Thank you for choosing this AEG product. We have created it to give you impeccable
performance for many years, with innovative technologies that help make life simpler –
features you might not find on ordinary appliances. Please spend a few minutes reading to get
the very best from it.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.aeg.com
Register your product for better service:
www.aeg.com/productregistration
Buy Accessories, Consumables and Original spare parts for your appliance:
www.aeg.com/shop
CUSTOMER CARE AND SERVICE
We recommend the use of original spare parts.
When contacting Service, ensure that you have the following data available.
The information can be found on the rating plate. Model, PNC, Serial Number.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
1. SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is
not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions
with the appliance for future reference.
1.1 Children and vulnerable people safety
WARNING!
Risk of suffocation, injury or permanent disability.
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep all detergents away from children.
• Keep children and pets away from the appliance door
when it is open.
• If the appliance has a child safety device, we recommend you activate it.
• Cleaning and user maintenance shall not be made by
children without supervision.
ENGLISH3
1.2 General Safety
• Before maintenance, deactivate the appliance and
disconnect the mains plug from the mains socket.
• Do not change the specification of this appliance.
• Obey the maximum load volume of 8 kg (refer to the
“Programme chart” chapter).
www.aeg.com
4
• If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• The operating water pressure (minimum and maximum) must be between 0,5 bar (0,05 MPa) and 8 bar
(0,8 MPa)
• The ventilation openings in the base (if applicable)
must not be obstructed by a carpet.
• The appliance is to be connected to the water mains
using the new supplied hose-sets. Old hose sets must
not be reused.
2.
SAFETY INSTRUCTIONS
2.1 Installation
• Remove all the packaging and the
transit bolts.
• Keep the transit bolts. When you
move the appliance again you must
block the drum.
• Do not install or use a damaged appli-
ance.
• Do not install or use the appliance
where the temperature is less than 0
°C or where it is exposed to the
weather.
• Obey the installation instruction sup-
plied with the appliance.
• Make sure that the floor where you in-
stall the appliance is flat, stable, heat
resistant and clean.
• Do not install the appliance where the
appliance door can not be fully
opened.
• Always be careful when you move the
appliance because it is heavy. Always
wear safety gloves.
• Make sure that there is air circulation
between the appliance and the floor.
• Adjust the feet to have the necessary
space between the appliance and the
carpet.
Electrical connection
WARNING!
Risk of fire and electrical shock.
• The appliance must be earthed.
• Make sure that the electrical information on the rating plate agrees with
the power supply. If not, contact an
electrician.
• Always use a correctly installed shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable.
Should the appliance power supply
cable need to be replaced, this must
be carried out by our Service Centre.
• Connect the mains plug to the mains
socket only at the end of the installation. Make sure that there is access to
the mains plug after the installation.
• Do not pull the mains cable to disconnect the appliance. Always pull the
mains plug.
• Do not touch the mains cable or the
mains plug with wet hands.
• This appliance complies with the
E.E.C. Directives.
Water connection
• Make sure not to cause damage to the
water hoses.
• The appliance is to be connected to
the water mains using the new supplied hose-sets. Old hose sets must
not be reused.
• Before you connect the appliance to
new pipes or pipes not used for a long
time, let the water flow until it is clean.
• The first time you use the appliance,
make sure that there is no leakage.
2.2 Use
WARNING!
Risk of injury, electrical shock,
fire, burns or damage to the appliance.
• Use this appliance in a household environment.
• Do not change the specification of this
appliance.
• Obey the safety instructions on the
detergent packaging.
• Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
• Do not touch the glass of the door
while a programme operates. The
glass can be hot.
• Make sure that you remove all metal
objects from the laundry.
ENGLISH5
• Do not put a container to collect possible water leakage under the appliance. Contact the Service to ensure
which accessories can be used.
2.3 Care and Cleaning
WARNING!
Risk of injury or damage to the
appliance.
• Before maintenance, deactivate the
appliance and disconnect the mains
plug from the mains socket.
• Do not use water spray and steam to
clean the appliance.
• Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
not use abrasive products, abrasive
cleaning pads, solvents or metal objects.
2.4 Disposal
WARNING!
Risk of injury or suffocation.
• Disconnect the appliance from the
mains supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent
children and pets to get closed in the
appliance.
3. TECHNICAL INFORMATION
DimensionsWidth / Height / Depth600 / 850 / 605 mm
Total depth640 mm
Electrical connection:Voltage
Overall power
Fuse
Frequency
Level of protection against ingress of solid particles
and moisture ensured by the protective cover, except where the low voltage equipment has no protection against moisture
230 V
2200 W
10 A
50 Hz
IPX4
www.aeg.com
6
Water supply pressureMinimum0,5 bar (0,05 MPa)
Maximum8 bar (0,8 MPa)
Water supply
1)
Cold water
Maximum loadCotton8 kg
Spin speedMaximum1400 rpm
1)
Connect the water inlet hose to a water tap with a 3/4'' thread.
4. PRODUCT DESCRIPTION
1238
Worktop
1
Detergent dispenser
2
Control panel
3
Door handle
4
Rating plate
5
Drain pump
6
9
0
4
5
1
6
7
Feet for the appliance level
7
Water drain hose
8
Water inlet valve
9
Mains cable
10
Transit bolts
11
Feet for the appliance level
12
2
4.1 Accessories
12
34
4.2 Child safety device
• When you activate this device, you
cannot close the door. This prevents
children or pets to be closed in the
drum. To activate the device, turn it
clockwise, until the groove is horizontal. To deactivate the device, turn it
counterclockwise, until the groove is
vertical.
ENGLISH7
Spanner
1
To remove the transit bolts.
Plastic caps
2
To close the holes on the rear side
of the cabinet after the removal of
the transit bolts.
Anti-flood inlet hose
3
To prevent possible leakage
Plastic hose guide
4
To connect the drain hose on the
edge of a sink.
5. CONTROL PANEL
123
ECO
SUPER ECO
20 Min. - 3 kg
On/Off button (On/Off)
1
Programme knob
2
Display
3
45678910
www.aeg.com
8
Start Pause button
4
Delay start button
5
Time save button
6
Extra rinse button
7
Stain button
8
Spin reduction button
9
Temperature button
10
5.1 On Off button
Press this button to activate or deactivate the appliance. A tune sounds when
the appliance is activated.
The AUTO Stand-by function automatically deactivates the appliance to decrease the energy consumption when:
• You do not use the appliance for 5 minutes before you press button
– All settings are cancelled.
–
Press button
pliance again.
5.3 Display
3
1
1
to activate the ap-
4
.
– Set again the washing programme
and all possible options.
• After 5 minutes from the end of the
washing programme. Refer to 'At the
end of programme'.
5.2 Programme knob
Turn this knob to set a programme. The
related programme indicator comes on.
ABCD
The display shows:
A• The maximum temperature of the programme.
B• The default spin speed of the programme.
1)
and 'Rinse Hold' symbols.
2)
C•
•
'No Spin'
The display symbols.
SymbolsDescription
Washing phase
2
Rinse phases
Spin phase
Child lock
You cannot open the appliance door when the symbol is
on.
You can open the door only when the symbol goes off.
If the programme is completed but the symbol stays on:
• There is water in the drum.
• The 'Rinse Hold' function is on.
Delay start
D• The programme time
When the programme starts, the time decreases with steps of 1 minute.
• The delay start
When you press the delay start button, the display shows the delay
start time.
• Alarm codes
If the appliance has a malfunction, the display shows alarm codes. Re-
fer to 'Troubleshooting' chapter.
•Err
The display shows this message for some seconds if:
– You set a function that is not applicable for the programme.
– You change the programme while it operates.
4
The indicator of the Start/Pause button
flashes.
•
When the programme is completed.
1)
Only available for Spin/Drain programme.
2)
The symbols appear on the display when the related phase or function is set.
5.4 Start/Pause button
Press button 4 to start or interrupt a
programme.
4
Some programmes accept only
one of the two functions.
5.7 Extra rinse button
ENGLISH9
7
5.5 Delay start button
Press button 5 to delay the start of a
programme from 30 minutes to 20 hours.
5.6 Time save button
Press the button 6 to decrease the
programme duration.
• Press one time to set 'Shortened duration' for items with daily soil.
• Press two times to set 'Extra Quick' for
items with almost no soil.
5
6
Press button 7 to add rinsing phases to
a programme.
Use this function for persons allergic to
detergents and in areas where the water
is soft.
5.8 Stain button
Press button 8 to add the stain phase
to a programme.
Use this function for laundry with hard
stains to remove.
When you set this function, put the stain
remover into compartment
8
.
www.aeg.com
10
This function increases the programme duration.
This function is not available with
a temperature lower than 40° C.
5.9 Spin button
Press this button to:
• Decrease the maximum speed of the
spin phase when you set a programme.
The display shows only the spin
speeds available with the set
programme.
• Deactivate the spin phase.
• Activate the 'Rinse Hold' function. Set
this function to prevent fabric creases.
The appliance does not drain the water when the programme is completed.
9
Spin phase is off.
'Rinse Hold' function is
on.
5.10 Temperature button
Press button 10 to change the default
temperature.
10
- -= cold water
5.11 Acoustic signals function
You can hear the acoustic signals when:
• You activate the appliance.
• You deactivate the appliance.
• You press the buttons.
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic sig-
8
nals, press button
the same time for 6 seconds.
If you deactivate the acoustic signals, they continue operate only
when you press the buttons and
when a malfunction occurs.
and button 7 at
5.12 Child lock function
This function prevents children to play
with the control panel.
• To activate the function, press button
10
and button 9 at the same time
until the display shows the symbol
• To deactivate the function, press but-
10
ton
and button 9 at the same
time until the symbol
You can activate the function:
• Before you press the Start/Pause but-
4
: the appliance cannot start.
ton
• After you press the Start/Pause button
4
, all the buttons and the pro-
gramme knob are deactivated.
goes off.
5.13 Permanent extra rinse
function
With this function you can keep the extra
rinse function permanently on when you
set a new programme.
• To activate the function press button
6
and button 5 at the same time
until the indicator of button
• To deactivate the function press but-
6
and button 5 at the same
ton
time until the indicator of button
off.
7
is on.
7
is
.
6. PROGRAMMES
Programme
Temperature
Cottons
95° - Cold
Type of load
max. weight of load
White and coloured
cotton with normal
soil.
max. 8 kg
Cycle
description
Wash
Rinses
Long spin
Functions
SPIN REDUCTION
RINSE HOLD
STAIN
EXTRA RINSE
TIME SAVE
1)
ENGLISH11
Programme
Temperature
Cottons+Prewash
95° - Cold
Extra Silent
95° - Cold
Synthetics
60° - Cold
Easy Iron
2)
60° - Cold
Delicates
40° - Cold
Wool/Silk
40° - Cold
Duvets
60° - 30°
Spin/Drain
3)
Rinse
Type of load
max. weight of load
White and coloured
cotton with heavy
soil.
max. 8 kg
White and coloured
cotton with normal
soil.
max. 8 kg
Synthetic or mixed
fabric items with normal level of soil.
Cycle
description
Prewash
Wash
Rinses
Long spin
Wash
Rinses
Stop with water
in the drum
Wash
Rinses
Short spin
max. 4 kg
Synthetic fabric items
with normal soil.
max. 4 kg
Delicate fabrics as
acrylics, viscose, polyester items with nor-
Wash
Rinses
Short spin
Wash
Rinses
Short spin
mal soil.
max. 4 kg
Machine washable
wool. Hand washable
wool and delicate
Wash
Rinses
Short spin
fabrics with «hand
washing» care symbol.
max. 2 kg
One synthetic blanket, duvet, bedspread and so on.
Wash
Rinses
Short spin
max. 3 kg
All fabrics
The maximum load
of the laundry is related to the type of
laundry.
Drainage of the
water
Spin phase at
the maximum
speed.
Hand washed items.Rinses
Long spin
Functions
SPIN REDUCTION
RINSE HOLD
STAIN
EXTRA RINSE
TIME SAVE
1)
STAIN
EXTRA RINSE
TIME SAVE
1)
SPIN REDUCTION
RINSE HOLD
STAIN
EXTRA RINSE
TIME SAVE
1)
RINSE HOLD
EXTRA RINSE
TIME SAVE
1)
SPIN REDUCTION
RINSE HOLD
STAIN
EXTRA RINSE
TIME SAVE
1)
SPIN REDUCTION
RINSE HOLD
SPIN REDUCTION
SPIN REDUCTION
NO SPIN
SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
4)
Loading...
+ 25 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.