263740.bk : 263740 Seite 5 Dienstag, Juni 17, 1997 11:59 AM
1
Safety instructions
The safety standards of AEG electric appliances are in keeping with the
recognised rules of technology and the law governing the safety of
appliances. Nevertheless as a manufacturer we are committed to
familiarise you with the following safety instructions:
General safety
Repairs to the washing machine may only be carried out by qualified
personnel. As a result of incorrect repairs considerable dangers for
the user may result. Please contact our customer service department
or an authorised AEG dealer in the event of repairs being necessary.
Never start the washing machine if the mains flex is damaged or the
control panel, work top or base area are so damaged that the inside
of the washing machine is accessible.
Switch off the washing machine before carrying out any cleaning,
care and maintenance work! You can make totally sure by pulling the
mains plug out of the socket or by switching off the fuse switch in
the fuse box.
Never use the flex to pull the plug out of the socket but pull the
actual plug.
Do not spray the washing machine with water.
During washing programs at a high temperature, the glass of the
door heats up. Do not touch!
Allow the water to cool down before cleaning the drain pump,
emergency emptying or opening the door in an emergency.
Small animals can nibble at power cables and water hoses. Electric
shock hazard and danger of damages from water!
Installation, connection and initial operation
Please follow the separate Installation and connection instructions.
If the machine is delivered during the winter at freezing tempera-
tures: store the washing machine for 24 hours at room temperature
before starting it.
Run the first washing cycle without washing (COTTONS 95, with half
the amount of washing powder) to remove residues from the drum
wich may have been left during manufacture.
5
263740.bk : 263740 Seite 6 Dienstag, Juni 17, 1997 11:59 AM
Safety instructions
Safety of children
Often children are not aware of the dangers involved in handling
electrical equipment. Therefore please ensure they are adequately
supervised whilst the appliance is on and do not allow children to
play with the washing machine there is a risk that the children may
lock themselves in the appliance.
Packaging (e.g. plastic films, polystyrene) could be dangerous for
children danger of suffocation! Keep packaging away from
children.
Please make sure that children or small animals do not climb into the
drum of the washing machine.
When disposing of the washing machine pull out the plug, cut off the
flex, dispose of the plug and remaining flex and destroy the door
lock. This hinders children from locking themselves in and
endangering their lives.
Intended use
Only use the washing machine to wash normal domestic washing. If
the washing machine is used for any other purpose or is incorrectly
used, the manufacturer adopts no liability for any damages which
may result.
Conversions or changes to washing machines are not permitted due
to safety reasons.
Only use washing powder which is suitable for washing machines.
Please follow the instructions of the washing powder manufacturers.
The washing may not contain any flammable solvents.
Please observe this above all when washing prewashed laundry.
Do not use your washing machine for dry cleaning.
Dyes and bleaching agents may only be used if specifically permitted
by the manufacturer of these products. We cannot be held liable for
any damages.
Installation must comply with local water authority and building
regulations requirements.
6
263740.bk : 263740 Seite 7 Dienstag, Juni 17, 1997 11:59 AM
2
Disposal
Dispose of the packaging!
Dispose of the packaging material of your washing machine correctly.
All packaging materials are environmentally friendly and can be
disposed of without any danger or burnt in the refuse incinerator.
The plastic parts can be reused:
The external plastic cover and the bags inside are made of
polyethylene (marking >PE<).
The padding is made of CFC free expanded polystyrene
(marking >PS<).
When disposing of the washing machine, cut off the mains cable, and
destroy the plug. Disable any door catches to prevent young children
being wrapped inside.
Use an authorised disposal site.
2
Environmental tips
For normally soiled washing you do not need a prewash. In this way
you can save washing powder, water and time (and not pollute the
environment!).
The washing machine works particularly economically if you exploit
the maximum loads.
For small quantities of washing use half to two thirds of the
recommended washing powder quantity.
By suitable pretreatment stains and a certain amount of dirt can be
removed. Then you can wash at a low temperature.
Wash slightly soiled to normally soiled cottons with the energy saving
program.
Often you do not need a fabric softener. Just try it! If you use a
tumble dryer your washing will become soft and fluffy without
softener.
7
263740.bk : 263740 Seite 8 Dienstag, Juni 17, 1997 11:59 AM
Important features of your appliance
Program and temperature setting using the program selector.
4 extra programs selectable with buttons.
Stain program for effectively treating stained washing.
Energy saving program for slightly soiled to normally soiled cottons.
Maximum Spin speed 1200 revolutions per minute, speed for the
final spin automatically adapted depending on the washing program:
COTTONS/LINEN1200 revolutions per minute
EASY CARES1000 revolutions per minute
DELICATES1000 revolutions per minute
WOOLLENS1000 revolutions per minute
Speed for the final spin can be changed to 1000, 800, 600 or 400
revolutions per minute.
Rinse hold can be added: the washing remains in the final rinse
water, it is not spun.
Delay timer: program start can be delayed by 1 to max. 19 hours
(e.g. to times with a more economical power rate).
Multi-display to show
estimated program duration or time left until the end of the
program,
delay timer (start time delay or time left to start of program),
error code.
Program progress display
Automatic load adaptation with fuzzy logic: sensor controlled
washing process with variable number of rinse cycles, water quantity
dependent on foam and load, controlled spin etc, thus best washing
and rinsing results with the lowest automatically adapted water
consumption.
4-chamber detergent compartment for washing powder and fabric
softener: temporally delayed addition of softener, washing powder
and stain removing agent enables environmentally friendly washing
and improves the effectiveness of the detergents.
ÖKO lock: The Öko lock ensures 100% effective detergent usage. The
Öko valve closes off the wash tub from the drainage system during all
wash programmes.
Scoop ribs in the washing machine drum: ensure washing is wet fast
and equally.
Anti-unbalance control system: for stability and smooth running.
8
263740.bk : 263740 Seite 9 Dienstag, Juni 17, 1997 11:59 AM
Important features of your appliance
Extra water switch: suds cooling only or suds cooling with extra
rinse can be set.
What does "update" mean?
The control system of your machine is fully electronic. The software
which determines this control system can be reprogrammed. If a state
of the art in washing technology is reached, your machine can be
updated.
9
263740.bk : 263740 Seite 10 Dienstag, Juni 17, 1997 11:59 AM
Description of the appliance
Front view
Control panel
Compartment for washing powder
and fabric softener
with handle flap
Rating plate
(behind door)
Door with
handle
10
Flap in front of
drain pump
Height adjustable feet;
263740.bk : 263740 Seite 11 Dienstag, Juni 17, 1997 11:59 AM
Description of the appliance
Control panel
Final spin speed/
RINSE HOLD button
Program progress
Program selector
DELAY TIMER button
Display
DOOR Lock
START/PAUSE
button
display
program option buttons
Multi-display
Program selector
The program selector determines the
type of the washing cycle (e.g. water
level, drum movement, number of
rinses, spin speed) in accordance with
the type of washing to be washed, as
well as the wash temperature of the
water. The different setting positions
have the following effect:
OFF
Switches the washing machine off, on all other positions it is on.
COTTONS/LINEN
Main wash for cottons/linen (washing at 30-95 °C rinsing /fabric
softening, spinning).
Position ENERGY SAVING:Energy saving of the program at approx.
2
67 °C for slightly to normally soiled cottons, extended washing time
(cannot be combined with QUICK WASH and STAIN).
OVERDOSING
display
11
263740.bk : 263740 Seite 12 Dienstag, Juni 17, 1997 11:59 AM
Description of the appliance
EASY CARES
Main wash for easy care fabrics (washing at 30-60 °C rinsing/fabric
softening, spinning).
DELICATES
Main wash for delicates (washing at 30-40 °C, rinsing/fabric softening,
spinning, higher water level and reduced drum movement).
WOOLLENS
Main wash for machine washable woollens and especially delicate
fabrics (wash cold up to 40 °C, rinsing/fabric softening, spinning, higher
water level and considerably reduced drum movement).
GENTLE RINSE
Separate gentle rinse, e.g. for rinsing fabrics washed by hand (2 rinses
and spin).
STARCHING
1 Rinse with fabric softener or a starching agent. Additives from the
w compartment is added.
PUMP OUT
Pumping out the water after a rinse hold (without any spinning at all).
SPIN
Pumping out the water after a rinse hold and spinning, or separate
spinning of hand washed cottons/ linen.
SHORT SPIN
Pumping out the water after a rinse hold and short spinning, or
separate short spin of handwashed, delicate fabrics (easy care washing,
delicates, woollens).
12
263740.bk : 263740 Seite 13 Dienstag, Juni 17, 1997 11:59 AM
Description of the appliance
Program Option buttons
The program option buttons are used to adjust the
washing program to the degree of soiling of the
washing.
Depending on the program different functions can
be combined.
PRE WASH
Cold prewash before the main wash which follows
automatically (not selectable for the WOOLLENS
setting).
SOAKING
Soak before the main wash which follows automatically (1 hour at
40 °C, extendable to max. 19 hours, not selectable for WOOLLENS
setting).
QUICK WASH
Shortened main wash for slightly soiled washing.
STAIN
To treat heavily soiled washing or stained washing with stain remover
(extended main wash with time optimised stain remover rinse, not
selectable for WOOLLENS setting).
Final spin speed/RINSE HOLD button
With this key you can change the maximum speed for
the final spin. With RINSE HOLD the washing stays in
the final rinse water, it is not spun.
START/ PAUSE button
This starts the washing program and enables the brief
interruption of a washing program.
DELAY TIMER button
With this button you can delay the start of a washing
program by 1 to max. 19 hours.
With the SOAKING button pushed the washing program starts
immediately, the soak is extended by the time set, the main wash
follows automatically.
13
263740.bk : 263740 Seite 14 Dienstag, Juni 17, 1997 11:59 AM
Description of the appliance
Displays
Display DOOR
This lamp indicates when the door can be
opened if the machine is on:
Green light = door can be opened
Light off = door can currently not be opened
Red light = door is open
Multi-display
The multi-display
shows the running time of the selected
program or the remaining wash time in
minutes (at the same time the display
lamp WASH TIME lights up); or
shows the delay time or the remaining
time in hours until the start of the
washing program; or
shows an error code (( and a number).
Program progress display
Before the start of the program, this shows
the program steps selected. During the
washing program, the display of the current
washing program step lights up.
OVERDOSING display
This shows that in the washing program which
has just run, too much washing powder was
used and due to this reason an extra rinse was
carried out.
14
263740.bk : 263740 Seite 15 Dienstag, Juni 17, 1997 11:59 AM
Description of the appliance
Compartment for washing powder and fabric softener
Suction cap
(must be firmly
pushed on)
Compartment for prewash detergent/soaking agent (water
k
softening agent if used).
They are added right at the beginning of the washing program.
Detergent compartment for main wash (and softening agent if
l
pre wash is being used).
They are added right at the beginning of the main washing
program.
Compartment for stain remover.
m
This is added during the STAIN program in the main wash at the
optimal time.
Compartment for liquid conditioners (fabric softener, starch).
w
They are added to the final rinse water.
15
263740.bk : 263740 Seite 16 Dienstag, Juni 17, 1997 11:59 AM
Consumption values and time required for selected
programs
The values in the following table were determined under standard
conditions. They provide a useful guide for household use.
Program selector/ Temperature
COTTONS/LINEN 955521.70125
COTTONS/LINEN 605521.00110
COTTONS/LINEN 405520.60100
EASY CARE 402.5530.4588
DELICATES 302.5500.4055
WOOLLENS 301520.3055
1) These times are approximate.
Load
in kg
Water
in litres
Energy
in kWh
1
Time
in
minutes
Before using your machine for the first time
0 Slightly pull the detergent compartment out of the control panel.
0 Pour about 1 litre of water through the detergent compartment into
the washing machine.
When this has been done the suds container will close and the ÖKO
lock can function correctly.
0 Run a wash cycle without washing (COTTONS 95, with half the amount
of washing powder).
This removes any residues from drum wich may have been left during
manufacture.
16
263740.bk : 263740 Seite 17 Dienstag, Juni 17, 1997 11:59 AM
Preparing the washing cycle
Sorting out and preparing washing
Sort out washing according to the type and care symbol (see "Types
of washing and care symbols").
Empty the pockets.
Remove any metal parts (safety pins, badges).
To prevent washing from getting damaged and forming bundles:
close zips, button up duvet covers and pillow cases, tie up loose straps
such as from aprons.
Turn clothes made from double layer fabric inside out (e.g. anoraks,
sleeping bags).
For knitted coloured fabrics as well as woollens and fabrics with
appliqué: turn inside out.
Put small and delicate items (baby socks, tights) in a washing net or a
pillow case with a zip.
Handle curtains with special care. Remove metal strips or plastic
hooks.
Keep coloureds and whites separately in different washing cycles.
When washing fabrics requiring different wash temperatures always
select the lowest temperature.
New coloured fabric often contains excess dyes. Wash this laundry
separately for the first time.
Mix small and large pieces of washing! This improves the
effectiveness of the wash and the washing is distributed better when
spinning.
Shake out washing before putting it into the machine.
Unfold the washing before putting it into the drum.
Types of washing and care symbols
The care symbols help to choose the correct washing program. The
washing should be sorted according to the type and care symbol.
The temperature specifications in the care symbols are always
maximum specifications.
17
263740.bk : 263740 Seite 18 Dienstag, Juni 17, 1997 11:59 AM
Preparing the washing cycle
Cottons
Fabrics made of cotton and linen with this care symbol will withstand
maximum wash actions and high temperatures. The COTTONS/LINEN
program is suitable for this type of washing.
Linens G
Fabrics made of cotton and linen with this care symbol will withstand
maximum wash actions and are colourfast at 40°C or 60°C. The
COTTONS/LINEN program is suitable for this type of washing.
Easy care washing D
Fabrics such as finished cottons, cotton mixtures and synthetics with
this care symbol require a softer washing action. The EASY CARES
program is suitable for this type of washing.
Delicates
Fabrics such as layered fabrics, microfibres, synthetics, curtains with this
care symbol require a very gentle treatment. The DELICATES program is
suitable for this type of washing.
Woollens and very delicate types of washing 9 ?
Fabrics such as wool, wool mixtures or silk with this care symbol require
a very gentle wash cycle. The WOOLLENS program is suitable for this
type of washing.
Woollens with 9
machine if they bear the addition "does not felt" or "suitable for
machine washing".
Fabrics with the care symbol 8 (Hand washing)
may not be washed in the washing machine!
Please follow care instructions "wash separately" and "wash separately
several times"!
I
D
C
H
B
(wool mark) may only be washed in the washing
or @
(Do not wash!)
Washing powders and conditioners
Which washing powder and conditioner?
Only use washing powders and fabric softeners suitable for automatic
washing machine use. As a general rule follow the instructions of the
producers.
18
263740.bk : 263740 Seite 19 Dienstag, Juni 17, 1997 11:59 AM
Preparing the washing cycle
How much washing powder and fabric softener?
The amount to be used depends on
the load:
If the washing powder producer does not make any specifications for
small loads, use a third less for half loads, and for very small loads
only use half of the amount of washing powder recommended for a
full load.
the degree of soiling of the washing:
For only slightly soiled washing use less washing powder. Follow the
instructions of the washing powder producer and load.
on the degree of hardness of the tap water:
The harder the water, the higher the dosage! You will find the
quantities to use according to water hardness on the washing powder
packaging.
Liquid detergent
Add liquid detergent using the dispenser provided by the detergent
manufacturer. Please follow the instructions on the package.
Using a water softening agent
In areas of hard water, the use of a water softening agent can reduce
the amount of detergent necessary. See manufacturers
recommendations.
19
263740.bk : 263740 Seite 20 Dienstag, Juni 17, 1997 11:59 AM
Run wash cycle
Brief instructions
A washing cycle consists of the following steps:
0 Set the correct washing program:
Set the program and temperature with the program selector.
Set any program options required, change the final spin speed / select
RINSE HOLD.
Set any DELAY TIMER if required.
0 Open the door, put in the washing.
0 Shut the door.
0 Add washing powder/conditioner.
0 Start washing program.
After the washing program has finished:
Important! If the washing cycle ended with rinse hold, carry out a
PUMP OUT, SPIN or SHORT SPIN before opening the door.
0 Open the door, remove the washing.
0 Switch off the washing machine: set the program selector to OFF.
0 We recommend you turn off the water supply when the wash program
has finished.
20
263740.bk : 263740 Seite 21 Dienstag, Juni 17, 1997 11:59 AM
Run wash cycle
Setting the washing program
See "Program tables" for suitable program, correct temperature and
3
any possible program options for the respective type of washing.
0 Set washing program and temperature:
set program selector to the washing
program desired with the required
temperature.
The estimated duration of the program
set is shown in minutes on the multi-
display.
0 If applicable select program options:
The displays of the program options selected
lights up.
To change your selection press another button.
To deselect simply press the button again.
0 If required change the spin speed for the final spin/
rinse hold: Press the final spin speed/RINSE HOLD
button repeatedly until the display of the required
spin speed or RINSE HOLD illuminates.
With RINSE HOLD the washing stays in the final rinse
water, it is not spun.
0 If applicable set the delay timer: press the DELAY
TIMER button repeatedly until the time delay
required is displayed, for example
delay start of the program.
If
is displayed and you press the button again the running time
3
19h
of the currently set washing program appears and the delay start is
cancelled.
When the SOAKING option is selected the delay timer determines the
soaking time. (Without delay timer the soaking time is approx. 1 hour.)
for a 12 hour
12h
21
263740.bk : 263740 Seite 22 Dienstag, Juni 17, 1997 11:59 AM
Run wash cycle
Loading the washing
0 Sort the washing according to the type and prepare it correctly.
For information about the correct preparation of
3
the washing see "Types of washing and care
symbols".
0 Open the door: pull at the handle of the door.
0 Load the washing.
See the "Program tables" for the maximum load.
3
0 Firmly shut the door.
Caution! When shutting the door be careful not to catch any pieces of
washing! The fabric and machine could be damaged.
22
263740.bk : 263740 Seite 23 Dienstag, Juni 17, 1997 11:59 AM
Run wash cycle
Adding washing powder/ fabric softener
0 Open the compartment: reach into the recess
under the compartment, pull the compartment
out as far as it will go.
0 Fill in washing powder/fabric softener.
For information about washing powder and fabric
3
softeners see section "Washing powder and
conditioners".
Prewash agent/soaking agent
k
(for extra programs PRE WASH/SOAKING),
or water softening agent if used.
Main detergent in powder form
l
(If you use water softening agent and need compartment k for
the prewash/soaking agent, add the water softening agent to
the main detergent compartment l.)
Stain remover (only for STAIN program)
m
Liquid conditioners (fabric softener, starch).
w
Important: Do not fill above the MAX mark. When using thick
concentrated fabric conditioners and starches we recommend
you dilute the concentrate with water to ensure trouble-free
dispensing.
If using starch powder dissolve according to manufacturers
instructions.
0 Push the compartment right in.
23
263740.bk : 263740 Seite 24 Dienstag, Juni 17, 1997 11:59 AM
Run wash cycle
Starting the washing program
0 Check the water tap is open.
0 Start the washing program: Press START/PAUSE button.
The washing program will start, or starts after the delay time set has
expired.
If the DOOR display is flashing red when the START/PAUSE button is
3
pushed, the door is not correctly closed. Firmly close the door and press
the START/PAUSE button again.
With the delay timer set:
The delay time set expires, in the multi-display the remaining time until
the start of the program is displayed (in hours). During this time, you
can add washing or change or cancel the delay timer.
Adding washing: press the START/ PAUSE button, this enables the
door to be opened. Then close the door and press the START/PAUSE
button again.
Changing or canceling the delay timer: press the button repeatedly
until the time desired is displayed; if the program running time is
displayed (such as
) the washing program will start immediately.
110
Progress of the washing program
Before the start the selected program steps are
displayed by the program progress display. During
the washing program the current program step is
shown.
The remaining wash time until the end of the
program is continuously displayed in minutes.
During a washing program the spin speed can still be
changed or RINSE HOLD can still be set. No other
settings can be changed.
With the START/PAUSE button, the washing program can be inter-
rupted at any time and continued by pressing the button again. The
washing program can also not be changed during the pause.
To change or stop the washing program, turn the program selector to
the OFF position.
24
263740.bk : 263740 Seite 25 Dienstag, Juni 17, 1997 11:59 AM
Run wash cycle
Washing cycle finished/ Removing the washing
If RINSE HOLD was selected:
0 After a rinse hold, the water has to be pumped out:
Either press the START/ PAUSE button (the washing is spun in
accordance with the program which has just finished; the final spin
speed can be changed whilst the washing is being spun using the spin
speed button,
or
turn the program selector to PUMP OUT and press the START/ PAUSE
button (the water is pumped out without the washing being spun),
or
turn the program selector to SPIN or SHORT SPIN and press the
START/PAUSE button (the washing is spun or spun gently).
After this program step has been completed the END lamp is
illuminated.
0 Open the door.
As soon as the DOOR display is green the door can be opened.
0 Turn the program selector to OFF.
0 Remove the washing.
0 After the program has finished, pull the washing powder compartment
out a little so that it can dry. Leave the door ajar for a while. This helps
to prevent stagnent smells and helps to preserve the door seal.
0 Close the water tap.
If the OVERDOSING display lights up it shows that too much washing
3
powder was used in the washing program which has just run. For this
reason an extra rinse was carried out. Check the dosage instructions of
the detergent manufacturers.
25
263740.bk : 263740 Seite 26 Dienstag, Juni 17, 1997 11:59 AM
Program tables
Washing
In the following not all possibilities, but only the ones used most often
and which are most useful are listed.
Type of washing,
care label
Cottons
I
Linen
G C
Easy cares
H D
Delicates
D
2
Wollens
9 ? B
Max. load
(dry weight)
5kg
5kg
2.5kg
2.5kg
(or 15-20m
curtains)
1kg
1
2
Program selector
Temperature
COTTONS/LINEN 95
Energy saving program:
COTTONS/LINEN
ENERGY SAVING
COTTONS/LINEN
30, 40, 50, 60
EASY CARES
30, 40, 50, 60
DELICATES
30, 40
WOOLLENS
COLD, 30, 40
Possible
extra
programs
PRE WASH
SOAKING
QUICK WASH
STAIN
PRE WASH
SOAKING
PRE WASH
SOAKING
QUICK WASH
STAIN
PRE WASH
SOAKING
QUICK WASH
STAIN
PRE WASH
SOAKING
QUICK WASH
STAIN
QUICK WASH
26
1) A 10 l bucket holds about 2.5kg of dry washing (cottons).
2) Woollens with the wool mark may only be washed in the machine if they bear
the addition "does not felt" or "suitable for washing machine".
263740.bk : 263740 Seite 27 Dienstag, Juni 17, 1997 11:59 AM
Program tables
Separate fabric softening/ starching
Type of washing
Cottons/Linen5kgSTARCHING
Max. load
(dry weight)
Program selector
Separate rinsing
Type of washing
Cottons/Linen5kg
Easy cares2.5kg
Delicates2.5kg
Woollens1kg
Max. load
(dry weight)
Program selector
GENTLE RINSE
Separate spinning
Type of washing
Cottons/Linen5kgSPIN
Easy cares2.5kg
Max. load
(dry weight)
Program selector
SHORT SPINDelicates2.5kg
Woollens1kg
27
263740.bk : 263740 Seite 28 Dienstag, Juni 17, 1997 11:59 AM
Maintenance and Cleaning
In daily use
0 After the program has finished pull out the detergent compartment a
little so that it can dry out.
0 Leave the door ajar for a while. This helps to prevent stagnent smellls,
and helps to preserve the door seal.
0 Close the water tap.
Control panel
Attention! Do not use household furniture polish or aggressive
detergents to clean the panel and operating parts
0 Wipe over the operating panel with a damp cloth. Only use warm
water.
Detergent compartment
Now and again the detergent compartment should be cleaned.
0 Pull out the detergent compartment as far as it will go.
0 Remove the detergent compartment by pulling firmly.
0 Remove the suction cap.
0 Clean the suction cap under running
water.
28
263740.bk : 263740 Seite 29 Dienstag, Juni 17, 1997 11:59 AM
Maintenance and Cleaning
0 Clean the separate compartments with
warm water from the back. A bottle
brush is a useful help here.
0 Push on the suction cap until the stop,
so that it is sitting tightly.
0 Clean the entire detergent
compartment inside area with a brush.
0 Insert the detergent compartment into the guides and push it in.
Washing machine drum
The washing machine drum is made from rust-free stainless steel. Any
objects left in the laundry wich are likely rust can stain the drum.
Attention! Do not clean the stainless steel drum with descaling agents
containing acids, scouring agents containing chlorine or iron or steel
wool.
0 Remove rust stains on the drum with a stainless steel cleaning agent.
Door
0 Regularly check if there are deposits or foreign bodies in the rubber
seal behind the door and remove them.
Precautionary measures in the event of a risk of frost
If the washing machine is located where temperatures may fall
3
below 0° C the following precautions must be taken:
0 Turn off water taps
0 Empty the appliance (see Carrying out an emergency emptying)
0 Disconnect the inlet hose.
29
263740.bk : 263740 Seite 30 Dienstag, Juni 17, 1997 11:59 AM
Troubleshooting
The whistling noise when spinning may be different to
3
your prevous washing machine wich is due to the
modern drive system.
Certain problems etc.
If you call out an engineer and the fault is listed here, a charge is levied
even if the appliance is in guarantee.
If in the display the error code (1 or
to solve the problem yourself.
Display (1 as for under "No water flows in".
Display (2 as for "Washing has not been spun well, ..." in the table of
disturbances below.
After eliminating the error, press the START/PAUSE button. If the error
code is displayed again, please contact your local AEG Service Force
Centre.
is displayed, you may be able
(2
30
FaultPossible causeRemedy
Washing machine does
not work.
No water flows in.
Error code
(1
appears.
The mains plug is not
connected.
The fuse of the household
electrical system is faulty.
The door is not correctly
closed.
START/PAUSE button not
pressed for long enough.
The water tap is closed.Open the water tap.
The Inlet filter in the clamp
of the inlet hose is blocked.
Plug in the mains plug.
Replace the fuse.
Close the door; you must
hear a click as it locks.
Press the START/PAUSE
button until the program
starts.
Unscrew the hose from the
tap, remove the filter and
clean it under flowing water.
263740.bk : 263740 Seite 31 Dienstag, Juni 17, 1997 11:59 AM
Troubleshooting
FaultPossible causeRemedy
Adjust the feet according to
The machine is not level.
the installation and
connection instruction.
Washing machine
vibrates during
operation or is
unsteady.
The suds in the main
wash cycle create too
much foam.
Water is leaking out
from under the
washing machine.
Fabric softener is not
added, compartment
À
for fabric softener
is filled with water.
There is very little washing in
the machine (e.g. only a bath
robe).
Water could not be comple-
tely pumped out before the
spin
- because there is a kink in
the outlet hose or
the drain pump is blocked.
Probably too much washing
powder was used.
The clamp on the inlet hose
is not tight.
The inlet hose has a leak.
The lid of the drain pump is
not correctly closed.
Washing is caught in the
door.
Suction cap in the
compartment for fabric
softener is not correctly
fitted or is blocked.
This does not hinder the
machine from functioning
correctly.
Check that the outlet hose is
correctly laid and if appli-
cable eliminate the kink or
clean the drain pump and if
necessary remove any
foreign bodies from the
pump housing.
Only use as much as the
washing powder manufac-
turer recommends.
Tighten the inlet hose clamp.
Check the inlet hose and if
necessary replace it.
Close the lid correctly.
Abort the program, remove
the washing caught in the
door, start a new program.
Clean the detergent
compartment, fit the
suction cap on firmly.
31
263740.bk : 263740 Seite 32 Dienstag, Juni 17, 1997 11:59 AM
Troubleshooting
FaultPossible causeRemedy
Washing has not been
spun well, there is
water left in the drum.
Error code
The door cannot be
opened with the
machine on.
The rinse water is
cloudy.
When pressing an
program option
button the
corresponding display
does not light up.
(2
appears.
There is a kink in the outlet
hose.
Maximum pumping height
(drain height 1m from the
position of the machine) is
exceeded.
Drain pump is blocked.
The water drainage system is
blocked.
The door is locked due to
safety reasons (DOOR
display is off).
Probably caused by a
washing powder with a high
silicate content.
The program option selected
is not available with the
program set.
Eliminate the kink.
Please contact AEG Service
Force Centre, it has a retro-
kit available for pump
heights above 1m.
Switch off the machine and
pull the plug out of the
socket, clean the drain pump.
Clean the blockage.
Wait until the DOOR display
is green.
This does not negatively
affect the rinse results. If
necessary use liquid
detergent.
Make another selection.
32
Washing powder
residues are left in the
washing powder
compartment.
The water tap is not fully
open.
The filter in the clamp of the
inlet hose is blocked.
The filter at the clamp
connection of the inlet hose
on the machine is blocked.
Open the water tap fully.
Clean the filter.
Clean the filter.
263740.bk : 263740 Seite 33 Dienstag, Juni 17, 1997 11:59 AM
Troubleshooting
If the washing results are not satisfactory
If the washing turns greyish and limescale deposits are present in
the drum
Insufficient washing powder has been added.
Incorrect washing powder was used.
Special stains were not pretreated.
Program or temperature was not set correctly.
When using modular washing powders the individual components
were not used in the correct ratio.
If there are still grey stains on the washing
Washing soiled with ointments, grease or oils was washed with
insufficient washing powder.
The temperature selected for the wash was too low.
A frequent cause is that fabric softener especially a concentrated one
has come into contact with the washing. Wash out these types of
stains as fast as possible and use the fabric softener carefully.
If after the final rinse foam is still visible
Modern washing powders can still cause foam in the final rinse cycle.
The washing is nevertheless sufficiently rinsed.
If there are white residues on the washing
These are insoluble contents of modern washing powders. They are
not the result of an insufficient rinse.
Shake out the washing or brush it off. Turn the washing inside before
washing it. Review your choice of powder, possibly use liquid
detergents.
Carrying out an emergency emptying
Warning! Switch off the washing machine before the emergency
1
emptying!
If the washing machine no longer pumps out the water an emergency
emptying must be carried out.
Warning! The water, which flow out of the emergency emptying hose
can be hot. First allow the water to cool down before emergency
emptying!
0 Put down a flat container to catch the water draining out.
33
263740.bk : 263740 Seite 34 Dienstag, Juni 17, 1997 11:59 AM
Troubleshooting
0 Pull down the flap in the left corner of
the base strip and remove it.
0 Release the emergency emptying hose
from its holder.
0 Pull the emergency emptying hose out a
little.
0 Place a container underneath to
catch the water.
0 Release the plugs of the emergency
emptying hose by turning them anti-
clockwise and pull them out.
The water will drain out. Depending on
the amount of water, it may be necessary
to empty the container to catch the
water several times. To do this, temporarily
close the emergency emptying hose again with the plugs.
When the water has drained out completely:
0 Push the plug firmly back into the emergency emptying hose.
0 Push the emergency emptying hose back in a little and let it catch onto
the holder.
0 Replace the flap in the base plate and close it.
When the washing machine is completely empty, the ÖKO lock can no
3
longer function correctly. Therefore before the next wash fill in approx
1 litre water (pour it in through the washing powder compartment).
Cleaning the drain pump
Warning! Switch off the washing machine and pull the plug out of the
1
socket before cleaning the drain pump!
0 First carry out an emergency emptying (see section "Carrying out an
emergency emptying").
0 Place a towel on the floor in front of the lid of the drain pump. Left
over water may flow out.
34
263740.bk : 263740 Seite 35 Dienstag, Juni 17, 1997 11:59 AM
Troubleshooting
0 Unscrew the lid of the drain pump by
twisting it anti-clockwise and pull it off.
0 Remove any foreign bodies which may be
in the pump housing.
0 Check whether the impeller of the pump
can be turned. (It is normal for the pump
to turn in steps.) If the impeller cannot be
turned at all please contact your local
AEG Service Force Centre.
0 Replace the lid (insert the ridges on the
lid into the guiding slots) and screw on
tightly in a clockwise direction.
0 Close the emergency emptying hose, push
it in and fasten it.
0 Close the flap.
Unlocking the door in an emergency
If the door cannot be opened (e.g. due to a faulty door lock or due to a
power cut during the washing program), it can be opened using the
emergency unlock feature.
0 If water can be seen in the window of the door first carry out an
emergency emptying (see section "Carrying out an emergency
emptying").
0 Turn the knob anti-clockwise with the help
of a coin or a screwdriver.
0 Open the door by pulling on the door
handle.
Knob
35
263740.bk : 263740 Seite 36 Dienstag, Juni 17, 1997 11:59 AM
Troubleshooting
Selecting suds cooling or an extra rinse
The washing machine is on a very economical water consumption
setting.
For people who suffer from a washing powder allergy, it may be helpful
to rinse with extra water (extra rinse cycle). This can be set with the
extra water switch:
Position 1: Suds cooling
The suds are cooled down before being pumped out at the end of the
main wash (by adding cold water). This reduces thermal shock to
fabrics, helping to prevent creasing. (This setting is only effective for
COTTONS/LINEN at a temperature of above 40 °C.)
Position 2: Suds cooling and extra rinse
The water is cooled down as for position 1, in addition to this (except
for WOOLLENS) an extra rinse cycle is carried out.
On delivery of the machine the extra water switch is in the 0 position.
Due to the process of cooling down the suds or an extra rinse cycle, the
3
water consumption and wash time is increased.
Setting:
0 Pull the washing powder compartment out until
the extra water switch on the left of the frame is
accessible.
0 Set the extra water switch to 1 (suds cooling) or 2
(suds cooling and extra rinse).
36
263740.bk : 263740 Seite 37 Dienstag, Juni 17, 1997 11:59 AM
Technical data
Height x width x depth85x60 x60cm
Depth with the door opened 95cm
Height adjustability approx. +10/-5mm
Empty weightapprox. 85kg
Full load (depending on the program)max. 5kg
Area of applicationhousehold
Drum speed when washing max. 53rpm
Drum speed when spinningsee type plate
Water pressure1-10bar
(=10100N/cm
This appliance complies with the following EC directives:
;
73/ 23 /EEC of 19/2/1973 Low voltage directive
89/ 336 /EEC of 3/5/1989 EMC directive including the
Modification directive 92/31 /EEC
2
= 0.11,0MPa)
-1
Power supply
Please refer to the type plate for specifications about the power supply.
The nominal voltage stated on the type plate and type of current must
be identical with the nominal voltage and type of current at the point
of installation. Also refer to the type plate for the fuse required.
Information for the electrician
When connecting the appliance without a plug, care must be taken
that this is done correctly. Please follow the relevant information in the
separate "Installation and connection instructions"
.
37
263740.bk : 263740 Seite 38 Dienstag, Juni 17, 1997 11:59 AM
Service & Spare Parts
If after carrying out the ecessary checks there is still a fault with your
appliance please contact your local AEG Service Force Centre.
In guarantee customers should ensure that the suggested checks
have been made as the engineer will make a charge if the fault is
not a mechanical or electrical breakdown.
Please note that proof of purchase is required for in-guarantee service
calls.
Service & Spare Parts
If you require a service engineer or wish to purchase spare parts,
contact your local AEG Service Force Centre, by telephoning
0990 234 234
Help us to help you
Please determine your type of enquiry before telephoning. When you
contact us we need to know.
1. Your name, address and post code.
2. Your telephone number.
3. Clear and concise details of the fault.
What is the fault?
When does the fault occur?
Does the multi-display issue an error-message ((and a number)?
4. The model, production number and product identification number.