AEG LAV62900 User Manual

LAVAMAT 62900

Washing machine

User information

Dear customer,

Please read this User Information carefully and keep it to refer to at a
later date.
Pass this User Information on to any subsequent owner of the appli­ance.

The following symbols are used in the text:

1 Safety instructions

Warning: Notes that concern your personal safety.
Attention: Notes that show how to avoid damage to the appliance.

3 Useful tips and hints

2 Environmental information

2

Contents

Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Programme overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Before the first wash. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Preparing and sorting washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Running a washing cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Opening the door/Loading the washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Adding detergent/ additives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Switching on the appliance/selecting a programme . . . . . . . . . . . . . . . . . . . 13

Changing the spin speed/Selecting rinse hold . . . . . . . . . . . . . . . . . . . . . . . . 13

Selecting the programme options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

EXTRA RINSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

QUICK WASH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

PREWASH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

STAIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Setting the delay timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Starting a programme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Programme progress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Interrupting a programme/Adding washing . . . . . . . . . . . . . . . . . . . . . . . . . . 16

End of the wash cycle/Removing the washing . . . . . . . . . . . . . . . . . . . . . . . 16

Child safety device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Cleaning and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

What to do if.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Remedying small malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

If the wash results are not satisfactory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Carrying out an emergency drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Drain pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Consumption values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3

Installation and connection instructions. . . . . . . . . . . . . . . . . 27

Safety information for the installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Installing the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Transporting the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Removing the transit packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Where to install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Making the appliance level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Connecting to the water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Water inflow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Water drainage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Guarantee/Customer Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

4

Operating Instructions

1 Safety

Prior to using for the first time

• Follow the ”Instructions for installation and connection”.

• If the appliance is delivered in the winter months when there are mi-

nus temperatures: Store the washing machine at room temperature
for 24 hours before using for the first time.

Correct use

• The washing machine is only designed for the washing of normal do­mestic laundry at home.

• Additions or modifications to the washing machine are not permit­ted.

• Use only detergents and additives that are suitable for use in domes­tic washing machines.

• The washing must not contain any inflammable solutions. Danger of
explosion!

• Do not use the washing machine for dry cleaning.

• Dyes/colour removers may only be used in the washing machine, if

the manufacturer of these products expressly permits this. We cannot
be held responsible for any damage arising.

Child safety

• Keep packaging away from children. There is a risk of suffocation.

• Children often do not recognise the hazards associated with electrical

appliances. Don’t allow children to use the washing machine unsu­pervised.

• Make sure that children and pets don’t climb into the drum of the
washing machine. Could endanger life!

5

General safety

• Repairs to the washing machine must only be carried out by qualified
service engineers.

• Never use the washing machine if the mains cable is damaged; or if
the control panel, work top or plinth area is damaged such that the
inside of the appliance is freely accessible.

• Switch off the washing machine before cleaning, maintenance and
servicing. In addition, pull the mains plug out of the socket or – in
the case of a permanent connection – switch off the cut-out in the
fuse box or remove the screw fuse completely.

• If operation is stopped, disconnect the appliance from the mains sup­ply and shut off the water tap.

• Never unplug the appliance by pulling on the cable. Always pull the
plug.

• Multi-way plugs, connectors and extension cables must not be used.

This could constitute a fire hazard through overheating.

• Never wash the washing machine down with a water jet. Danger of
electric shock!

• In washing programmes with high temperatures the glass in the door
gets hot. Do not touch it.

• Before emergency emptying of the appliance, before cleaning the
drain pump or opening the door in an emergency, let the water cool
down.

• Small animals can nibble at the cables and water hoses. Danger of
electric shock and danger of water damage! Keep small animals away
from the washing machine.

6

Description of the appliance

Detergent dispenser
drawer

Rating plate
(behind door)

Screw feet
(height adjustable)

Control panel

SPIN/RINSE HOLD button

DELAY TIMER button

Control panel

Plinth flap/
Drain pump

Multidisplay

Programme Progress display

Programme option
buttons

START/PAUSE button

DOOR indicator

Programme knob

7

Programme overview

Programme options Spin speed

Programme

ECO (ENERGY SAVING)

(COTTONS/LINEN)

95, 60, 50, 40, 30

(EASY-CARES)

60, 50, 40, 30

2)

1)

max. load

(dry washing)

(EXTRA RINSE)

(QUICK WASH)

(PRE WASH)

(STAIN)

Schleudern-hoch

1200/ 1000/600

6kg • • • • • •

6kg • •

3)

3kg • • • •

• •

4)

• • •

4)

• •

l (EASY IRON) 40 1kg • • • • • •

(DELICATES)

40, 30

/ (WOOL/SILK)

(HANDWASH) 40, 30, X (COLD)

3kg • • • • •

2kg • •

(GENTLE RINSE) 3kg • •

(DRAIN)

n (RINSE HOLD)

(SPIN) 6kg • •

a (REFRESH) 3kg • •

1) A 10 litre bucket contains approx. 2.5 kg of dry washing (cotton)

2) Programme settings for tests in accordance with or support of EN 60 456 and IEC 60 456 are described in
the section “Consumption values”.

3) Recommended load for short progammes is 3 kg; full loading is possible however with somewhat reduced
cleaning results.

4) } (STAIN) can only be selected with wash temperatures of 40°C and above, as stain treatment products are
only effective at higher temperatures.

8

Application/features: Care symbols1)

Energy-saving programme at 60 °C for lightly to normally soiled whites/
coloureds made of cotton/linen.

Programme for normally to heavily soiled whites/coloureds made of cotton/
linen.

Programme for easy-care mixed fibres and synthetics.

Special programme which washes at 40 °C for easy-care fabrics which after
being washed using this programme need to be ironed only lightly or not at all.

Gentle programme for delicate fabrics such as bonded fabrics, microfibres,
synthetics, net curtains (max. load for net curtains 20 to 25 m
(RINSE HOLD) also suitable for fabrics with climate membrane, e.g., outdoor
clothing.

Particularly delicate programme for machine washable and hand washable
wool/silk.

Separate gentle rinse cycle (3 rinses, liquid conditioner is washed in from com­partment &, gentle spin).

Drains water away after a rinse hold.

Drains water out and spins, e.g. after a rinse hold, or separate spin for hand­washed cottons/linens.

Special programme at 30 °C, approx. 30 minutes long, for quickly washing
through items such as e.g. slightly dirty sports clothing that have been worn
once or new clothes.

1) The figures in the care symbols indicate the maximum temperatures.

2

). With n

M O

J M O

I K N

K N

I K

Q L H

I K N
Q L

H

J M O

J M O
I K N

9

Before the first wash

1. Open the detergent drawer.

2. Pour approx. 1 litre of water through the detergent drawer into the

washing machine.
This closes the water container when the next programme is started

and the economy valve can function properly.

3. In order to remove any residues from the drum and water container
which may have been left during manufacturing, perform the first
wash cycle without any washing in the machine. Programme:

(COTTONS/LINEN) 60, press (QUICK WASH), add approx. 1/4

measuring cup of washing powder.

Preparing and sorting washing

Preparing washing

• Empty pockets. Remove foreign bodies (e. g. coins, paper clips, nails,

etc.).

• Do up zips, button up covers to prevent damage to washing.

• Remove the runners from net curtains or cover them with a net or a

bag.

• Wash sensitive and small items in a net or a pillow case, e.g. net cur-

tains, tights, socks, handkerchiefs, bras.

Important! Bras and other items containing wires should only be
washed in a net bag. The wires can work loose and damage the appli­ance.

10

Sorting washing

• By colour: Wash white and coloured washing separately. Washing can

run.

• By temperature, type of washing and care symbol.
Important! Do not wash fabrics with care symbol G (= do not wash!)

in the washing machine.

Running a washing cycle

Opening the door/Loading the washing

1. To open the door: gently pull the handle on the door.

When the machine is switched on, the lights (DOOR) and
(START/PAUSE) indicate whether the door can be opened:

light (DOOR) light (START/PAUSE) Can the door be opened?

lit green flashes red or is off yes

lit green lit red

lit red

or is off

flashes red

or lit red

2. Unfold washing and load it loosely
into the machine. Mix large and
small items.
Important: Do not get any washing
caught between the door and the
rubber seal.

3. Press the door firmly shut. Door
catch must audibly latch.

yes, after pressing the

(START/PAUSE) button

no, water level too high or

temperature too high

Adding detergent/additives

Important: Use only detergents and additives that are suitable for use

in domestic washing machines.

1 For USA and Canada only!

Important! Only LOW-SUDSING detergent suitable for a front-loading
washing machine can be used in this machine. This machine can heat
the water up to 95 degrees celsius, or 200 degrees fahrenheit, and care
should be taken to ensure that the correct washing powder is used. If
you have any doubt, check with your dealer or the distributor.

WARRANTY AND CONSEQUENTIAL DAMAGES ARE VOIDED IF A LOW
SUDSING DETERGENT IS NOT USED.

Dose detergent and additives according to the instructions of the de­tergent and additive manufacturers. Follow the instructions on the
packaging.

11

Dosing depends upon:

– the washing’s degree of soiling,
– the size of the load
– the degree of hardness of the water supply.

• If the manufacturer does not give instructions for small loads: for a

half load, use a third less, for a very small load, use only half of the
detergent that is recommended for a full load.

• From water hardness 2 (= medium) upwards, water softener should

be used. Detergent can then always be dosed for water hardness 1
(= soft). Your local water company will be able to give you informa­tion about the water hardness in your area.

1. Pull the detergent dispenser drawer out as far as the stop.

2. Add the detergent/additives.

3. Push the drawer in fully.

Washing powder/tablets
for the main wash

Softeners/
wash-care products
to preserve the shape
of garments/
starch

In-wash stain treatment/
tablets

Washing powder/tablets
for the pre-wash
or for water softener

Washing powder/tablets for the main wash
If you are using water softener and need the right-hand compartment

for the pre-wash detergent, add the water softener to the main wash
detergent in the left-hand compartment.

Softeners, wash-care products to preserve the shape of garments,
starch

Do not fill the compartment beyond the MAX mark. Dilute thick liquid
concentrates according to the manufacturer’s instructions before
putting them into the drawer. Dissolve powder starches.

If you use liquid detergents:
Add liquid detergent using the dosage container provided by the deter­gent manufacturer.

12

Switching on the appliance/selecting a programme

Set the programme and tempera­ture using the programme knob.

3 By selecting a programme, you

switch the appliance on at the
same time.
– The programme progress display

indicates the programme steps
that the selected programme will
perform.

– In the multi-display the

estimated length of the programme (in minutes) appears.

Changing the spin speed/Selecting rinse hold

The washing machine suggests the
maximum permitted speed that is
suitable for the selected pro­gramme. You can reduce this
speed:

Press the SPIN/ (RINSE HOLD)
button repeatedly, until the desired
indicator lights up.

3 The speed for the final spin can still be altered during the programme.

To do this:

1. Press the button (START/PAUSE).

2. Change the speed.

3. Press the button (START/PAUSE) again.

(RINSE HOLD)

With (RINSE HOLD) the washing is left to soak in the final rinse wa­ter. There is no final spin after the intermediate spin(s). Intermediate
spins are programme-dependent and cannot be altered.

13

Selecting the programme options

If desired, press the programme op­tion button(s). The corresponding
indicator lights up.

3 If “Err” is flashing in the multi-

display, the programme option se­lected cannot be combined with the
wash programme set.

EXTRA RINSE

With the programmes ECO (ENERGY SAVING), (COTTONS/LINEN),

(DELICATES), (EASY-CARES) and l (EASY IRON) two addi-

tional rinses are carried out (e. g. in cases of over-sensitive skin).

QUICK WASH

Shortened wash programme for less soiled items.

PREWASH

Hot pre-wash before the main wash that follows automatically; with
intermediate spin for (COTTONS/LINEN) and (EASY-CARES),
without intermediate spin for (DELICATES).

14

STAIN

For heavily soiled or stained washing. In-wash stain treatments are
washed in at the optimum time as the programme progresses. Can only
be used for washing temperatures of above 40°C as stain removers are
not effective at lower temperatures.

Setting the delay timer

3 Using the button (DELAY TIMER) you can delay the start of a pro-

gramme by 30 minutes (30') to a maximum of 23 hours (23h).

1. Select the programme.

2. Press the button (DELAY TIMER) repeatedly until the multi-display

shows the desired time delay, e. g., 12h, if the programme is to start in
12 hours. The indicator (DELAY TIMER) will light up.

3 If the display is showing 23h and you press the button again, the time

delay will be cancelled. 0' will appear followed by the length of the
wash programme that has been set.

3. To activate the delay timer, press the
time remaining to the start of the programme is continuously displayed
(e. g., 12h, 11h, 10h,... 30

' etc.).

button (START/PAUSE). The

Starting a programme

1. Check that the tap is turned on.

2. Press the

starts after the time delay set has elapsed.

button (START/PAUSE). The programme is started or it

3 If after pressing the button (START/PAUSE) E40 flashes in the

multi-display, the (END) indicator flashes 4x and at the same time an
acoustic signal sounds 4x, the door has not been correctly shut. Push
the door firmly closed and press the

button (START/PAUSE) again.

Programme progress

• The programme progress display shows the programme step that is

currently being carried out.

– (Prewash)
– (Main wash)
– (Rinse)
– (Extra Rinse)
– (Spin)
– (End)

• The multi-display shows the estimated time remaining (in hours and

minutes) until the end of the programme.

3 The remaining programme time may increase or briefly remain constant

during the wash programme as the programme adjusts to various con­ditions while washing (e. g. type of washing, amount of washing, rec­ognising out-of-balance when spinning, special rinse cycle, etc.).

15

Interrupting a programme/Adding washing

Interrupting a programme

• A washing programme can be interrupted at any time by pressing the

button (START/PAUSE) and then re-started by pressing the
button (START/PAUSE) again.

• To stop the washing machine before the programme has ended, turn

the programme knob to (OFF). Important: Be careful if there is
water in the appliance!

Adding washing

It is possible to add washing, as long as the (DOOR) light is lit green.

1. Press the

2. Close the door and press the

button (START/PAUSE). The door can be opened.

button (START/PAUSE) again. The

programme will continue.

End of the wash cycle/Removing the washing

When the programme has finished, (END) will illuminate on the pro­gramme progress display. The door can be opened as soon as the in­dicator (DOOR) is lit green.

1. Open the door and remove the washing.

2. Turn the programme knob to (OFF).

3. Close the water tap.

4. When you have finished washing, pull out the detergent drawer a little

to let it to dry out. Keep the door very slightly open so that the washing
machine can air.

16

(RINSE HOLD) has been selected:

If

Following a rinse hold (END) will be lit on the programme progress
display.
The water must first be drained off:
– Either turn the programme knob to (OFF), then to (DRAIN) and

press the button (START/PAUSE) (the water will be drained
without spinning),

– turn the programme knob to (OFF) and then to (SPIN). Change

the spin speed, if necessary, and press the button (START/

PAUSE) (the water will be drained and the washing spun).

Child safety device

When the child safety device is set, the door can no longer be closed.

Setting the child safety device:

Use a coin to turn the knob (on the
inside of the door) in a clockwise di­rection as far as it will go.

1 Warning! The knob must not be

sunk-in after being set, otherwise
the child safety device is not active.
The knob must stand proud as
shown in the illustration.

Releasing the child safety device:
Turn the knob anti-clockwise as far

as it will go.

17

Cleaning and maintenance

Important! Do not use furniture care products or aggressive cleaners to

clean the appliance.
Wipe control panel and body with a damp cloth.

Cleaning procedure

If you plan to wash mainly at low temperature, you should run a hot
programme from time to time. This will reduce any deposits and clean
the appliance from the inside.

Detergent dispenser drawer

The detergent dispenser drawer should be cleaned regularly.

1. Remove the detergent dispenser drawer by pulling it firmly.

2. Remove the conditioner insert from

the middle compartment.

3. Clean all parts with water.

4. Put the conditioner insert in as far as

it will go, so that it is firmly in place.

5. Clean all parts of the washing ma­chine, especially the nozzles in the
top of the washing-in chamber, with
a brush.

6. Insert the detergent dispenser draw­er in the guide rails and push it in.

Washing drum

Rust deposits in the drum may occur due to rusting foreign bodies in
the washing or tap water containing iron.

Important! Do not clean the drum with acidic descaling agents, scour­ing agents containing chlorine or iron or steel wool.

1. Remove any rust deposits on the drum with a cleaning agent for stain­less steel.

2. Run a washing cycle without any washing to clean off any cleaning
agent residues. Programme: (COTTONS/LINEN) 60, press the button

(QUICK WASH), add approx. 1/4 measuring cup of washing powder.

18

Door and rubber collar

Regularly check whether deposits or foreign bodies are present in the
folds of the rubber collar or on the inside of the glass door.
Clean the glass in the door and the rubber collar regularly.

What to do if...

Remedying small malfunctions

If during use of the appliance one of the following error codes is shown
in the multi-display:

– E10 (Problems with water inflow),
– E20 (Problems with water outflow),
– E40 (door open),

please have a look at the following table.
When the fault is remedied, press the button (START/PAUSE).

In the event of other errors (E and a number or letter): Switch the ap­pliance off and then on again. Re-set the programme. Press the

button (START/PAUSE).

If the error appears again, please contact the Customer Care Depart­ment, stating the error code.

Problem Possible cause Remedy

Washing machine is not
working.

The door cannot be
closed.

When a button is
pressed, Err appears in
the multi-display.

E40 appears.
indicator (END)
flashes 4x, at the same
time an acoustic signal
sounds 4x.

Mains plug not plugged in
or fuse not working.

Door not closed properly.

The button (START/

PAUSE) button was not

pressed for long enough.

Child safety device engaged.

The selected function can­not be combined with the
programme set.

The door is not closed prop­erly.

Connect the plug to a mains
socket. Check fuse.

Close door - there should be
an audible click.

Press the button
(START/ PAUSE).

Release the child safety de­vice.

Select another function.

Close the door properly. Re­start the programme.

19

Problem Possible cause Remedy

E10 appears.
indicator (END)
flashes 1x, at the same
time an acoustic signal
sounds 1x.
(Problems with water
inflow)

The washing machine
vibrates when operating
or is not stable.

Washing has not been
spun.

Water is running out
from under the washing
machine.

Washing water is foam­ing excessively. At the
end of the washing cy­cle, the spin stops.

E20 appears.
indicator (END)
flashes 2x, at the same
time an acoustic signal
sounds 2x.
(Problems with water
outflow)

Tap turned off. Turn on the tap.

The filter in the threaded in­let hose fitting is blocked.

Water tap is furred with
lime scale or is faulty.

The transit packaging has
not been removed.

The screw feet not correctly
adjusted.

Only a few large items of
washing in the drum.

Screw connection on the in­let hose is leaking.

Drain hose is leaking. Replace drain hose.

Drain pump cover is not
closed properly.

Washing was caught in the
door.

Emergency drain hose is
leaking.

Probably too much deter­gent has been used.

Kink in drain hose. Straighten the hose.

Maximum pumping height
of 1m exceeded.

Drain pump is blocked.

For sink spigot connections:
The sink spigot is blocked.

Turn off the tap. Unscrew the
hose, take out the filter and
clean it.

Check the tap and have it re­paired, if necessary.

Removing the transit pack­aging.

Adjust the feet as described
in the installation and con­nection instructions.

Always load the drum as full
as possible. Mix large and
small items.

Screw the inlet hose on
tightly.

Close the cover properly.

Load washing carefully for
the next wash.

Close off emergency drain
hose properly.

Follow the manufacturer's
instructions exactly when
measuring out detergent.

Please contact the Customer
Care Department.

Switch off the appliance.
Disconnect the power plug.
Clean the drain pump. Re­move foreign bodies from
the pump housing.

Clean the sink spigot.

20

Problem Possible cause Remedy

Conditioner not rinsed
in, w compartment for
additives is filled with
water.

The door cannot be
opened when the wash­ing machine is switched
on.

Washing is heavily
creased.

Conditioner insert in the
compartment for additives
is not correctly attached or
is blocked.

Door locked.

There has been a power cut.
(All indicators are off.)
For safety reasons, the door
remains locked for approx. 4
to 10 minutes.

Possibly too much washing
was loaded.

Clean the detergent drawer,
insert the conditioner insert
firmly.

Wait until indicator
(DOOR) is lit green.

The programme will continue
when the power cut is over.

To remove washing:
If water can be seen in the
appliance, before opening
the door, first drain off the
water. (See section “Carrying
out an emergency drain”.)

Observe maximum loads.

21

If the wash results are not satisfactory

Washing is grey and scale is being deposited in the drum

• Too little detergent is being used.

• The right detergent was not used.

• Special soiling was not pre-treated.

• Programme or temperature was not correctly set.

There are grey stains on the washing.

• Washing soiled with ointment, grease or oil was washed with too lit-

tle detergent.

• It was washed at too low a temperature.

• A common cause is that fabric conditioner – especially a concentrate

– has got onto the washing. Such stains should be washed out as
quickly as possible and make sure that you are careful when using
fabric conditioner.

After the last rinse foam can still be seen.

• Modern detergents may create foam even in the last rinse cycle. The

washing is however sufficiently rinsed.

There are white residues on the washing.

• This is due to the insoluble ingredients in modern detergents.

They are not caused by insufficient rinsing.
Shake or brush the washing. If possible turn the washing inside out
before washing. Check your choice of detergent. Especially with dark
colours it is advisable to use liquid detergents.

22

Carrying out an emergency drain

1 Warning! Before emergency draining, switch off the washing machine

and remove the mains plug from the socket.
Warning! The water that comes out of the emergency drain hose may

be hot. There is a risk of scalding. Let the water cool before performing
an emergency drain.

1. Open the plinth flap and remove it.

2. Take out the emergency drain hose.

3. Place a shallow container under-

neath it. Then loosen the drain plug
by turning it in an anti-clockwise
direction and pull it out.

4. The water runs out. If it is necessary
to empty the container more than
once, seal up the emergency drain
hose with the drain plug while you
are doing so.

When the water has all drained away:

5. Push the drain plug firmly into the emergency drain hose and screw it

tight in a clockwise direction.

6. Place the emergency drain hose back in the support.

7. Insert the plinth flap and close it.

23

Drain pump

The drain pump is maintenance-free. It is only necessary to open the
pump cover if there is a malfunction and water is no longer being
pumped out, e. g. if the pump wheel is blocked.
Please make sure before loading the washing that there are no foreign
bodies in the pockets or caught between the washing. Paperclips, nails,
etc. that may have got into the washing machine with the washing re­main in the pump housing (foreign body trap that protects the pump
wheel).

1 Warning! Before opening the pump cover, switch off the washing ma-

chine and remove the mains plug from the socket.

1. First carry out an emergency drain.

2. Place a cloth on the floor in front of the drain pump cover.

Residual water runs out.

3. Unscrew the pump cover in an anti­clockwise direction and remove it.

4. Remove foreign bodies and fluff
from the pump housing and from
the pump wheel.

5. Check whether the pump wheel
right at the back of the pump hous­ing can turn. (It is normal for the
pumping wheel to turn jerkily.) If
the pumping wheel cannot be
turned, please contact the Customer
Care Department.

6. Insert the pump cover. Insert the
guides at the sides of the cover into
the guide slots and tighten the cov­er by turning in a clockwise
direction.

7. Close off the emergency drain hose
and place it in the support.

8. Close plinth flap.

24

Disposal

Packaging material

2

The packaging materials are environmentally friendly and can be recy­cled. The plastic components are identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging materials in the appropriate
container at the community waste disposal facilities.

2 Old appliance

The symbol
product may not be treated as household waste. Instead it shall be
handed over to the applicable collection point for the recycling of elec­trical and electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed infor­mation about recycling of this product, please contact your local city
office, your household waste disposal service or the shop where you
purchased the product.

W on the product or on its packaging indicates that this

1 Warning! When an appliance is finished with, remove the plug from

the mains socket. Cut off the cable and plug and dispose of them.
Destroy the door lock. This prevents children from trapping themselves
inside and endangering their lives.

25

Technical data

This appliance conforms with the following EU Directives:

5

– 73/23/EEC dated 19.02.1973 Low Voltage Directive
– 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending

Directive 92/31/EEC

– 93/68/EEC dated 22.07.1993 CE Marking Directive

Height x Width x Depth 850 x 598 x 603 mm

Depth when door is open 980 mm

Height adjustment approx. +10/-5mm

Load (depending on programme) Max. 6kg

Area of use Domestic

Drum spin speed see Rating Plate

Water pressure 1-10bar (=10–100N/cm2=0.1–1.0MPa)

Consumption values

The consumption values were obtained under standardised conditions.
They may vary when operating in domestic conditions.

26

Programme selector

Temperature

(COTTONS/LINEN) 95 6 62 2,20

ECO (ENERGY SAVING)

(COTTONS/LINEN) 40 6 58 0,70

(EASY-CARES) 40 3 58 0,52

(DELICATES) 30 3 58 0,42

/ / (WOOL/SILK/HANDWASH) 30 2 54 0,35

1) The load size is determined in accordance with the EN 60456 standard load.

2) Note: Programme setting for testing in accordance with or in support of Standard

EN 60 456 and IEC 60 456. Consumption values will vary from those quoted depend­ing on the pressure and hardness of the water and its initial temperature, the room
temperature, type and quantity of washing, detergent used, fluctuations in mains
voltage and options selected.

2)

Load size

1)

in kg

6 49 1,02

Water

in litres

Energy

in kWh

Installation and connection instructions

1 Safety information for the installation

• This washing machine cannot be built-in.

• Before using for the first time, check the appliance for damage sus-

tained while it was being transported. Do not under any circumstanc­es connect an appliance that is damaged. In the case of damage,
please contact your supplier.

• Before using for the first time, all parts of the transit packaging must

be removed. Otherwise when spinning damage may be caused to the
appliance or to neighbouring units or furniture.

• Before using the appliance for the first time, splash protection must

be completed. (See “Removing the transit packaging”.)

• Always plug the mains plug into a correctly installed shockproof

socket.

• Permanent connection: a permanent connection must only be in-

stalled by a trained electrician.

• Prior to using the appliance for the first time, ensure that the rated

voltage and type of supply on the rating plate match that of the sup­ply where the appliance is to be installed. The fuse rating is also to be
found on the rating plate.

• If work on the plumbing is required for the proper connection of the

washing machine to the water supply, this must be undertaken by a
registered plumber.

• If work on the electricity supply system is required for the proper

connection of the washing machine to the electricity supply, this
must be undertaken by a registered electrician.

• The washing machine’s cable must only be replaced by the Customer

Care Department or a registered electrician.

27

Installing the appliance

Transporting the appliance

1 Warning! The washing machine is very heavy. Risk of injury. Be careful

when lifting.

• Do not lay the appliance on its front nor on its right side (as seen

from the front). Electrical components may get wet.

• Never transport the appliance without its transit packaging. Only re-

move the transit packaging when the appliance is in its place of in­stallation. Transporting the appliance without its transit packaging
can lead to damage to the appliance.

• Never lift the appliance by the door when it is open nor by the plinth.

When moving using a sack trolley:

• Only use the sack trolley on the side of the appliance.

Removing the transit packaging

Important! Before using the appli-

ance for the first time, all parts of
the transit packaging must be re­moved! Keep the transit packaging
in a safe place, in case it is needed at
a later date when the appliance is to
be moved (e.g. moving house).

1. At the back of the appliance, open
both hose clips and remove both
hoses and mains cable.

2. Remove both hose clips from the ap­pliance by jerking them hard.

28

3. Remove both plastic caps sideways.

3 Special spanner A and sealing caps B

(2 off) and C (1 off) are supplied
with the appliance.

4. Remove screw D with its compres­sion spring using special spanner A.

5. Turn sealing cap C upside down as
shown in the illustration.

6. Seal hole using sealing cap C.

7. Unscrew and remove two screws E

using special spanner A.

8. Unscrew and remove four screws F
using special spanner A.

9. Remove transit bar G.

10. Screw in the four screws F again.

11. Seal the two big holes using sealing

caps B.
Important! Press all sealing caps B

(2 off) and C (1 off) in firmly, so that
they snap into place. (Splash protec­tion).

29

Where to install

Important! The appliance must not be used in a room where there is a

danger of frost. Frost damage or impaired operation! Frost damage is
not covered by the warranty.

• The surface on which the appliance is to be installed must be firm

and level. Do not install the appliance on carpets or on soft floor cov­erings.

• The surface on which the appliance is to be installed must be clean

and dry and free from coverings that move, so that the appliance
does not slide.

• If the location in which the appliance is to be installed is fitted with

small-format tiles, put a rubber mat (available in the shops) under
the appliance.

If the appliance is to stand on a
plinth:

In order for the appliance to be se­cure on the plinth, fixing plates*)
must be mounted, into which the
appliance is inserted.

If the appliance is to stand on floors that vibrate, e. g. floors of
wooden joists with deal boards:

If possible, install the appliance in one corner of the room.

1. Screw a water-resistant wooden board (at least 15 mm thick) onto at
least 2 of the floor joists.

2. Affix fixing plates *) onto the wooden board, into which the appliance
is inserted.
*) The fixing plates can be obtained from the Customer Care Depart­ment.

30

Making the appliance level

The four feet of the appliance are
pre-adjusted.
Large degrees of unevenness can be
compensated for by individually ad­justing the height adjustable screw
feet.
Use the special spanner supplied to
do this.

Important! Do not use pieces of
wood, cardboard or such like to lev­el out unevenness in the floor, but
adjust the height adjustable screw
feet instead.

Electrical connection

Details about the voltage, type of supply and the fuses required are to
be found on the rating plate. The rating plate is next to the doorway.

Connecting to the water supply

Important!

• This appliance must not be connected to the hot water system.

• When connecting it, use only new hose kits.

• Only connect the appliance to the drinking water supply. Rain water

or water for industrial use may only be used if it fulfils the require­ments of DIN1986 and DIN1988.

• Do not kink or crush the water inlet hose or drain hose.

Permitted water pressure

The water pressure must be at least 1 bar (= 10N/cm2=0.1MPa) and may
be a maximum of 10bar (= 100N/cm

– If more than 10 bar: Connect a pressure reduction valve.
– If less than 1bar: Disconnect the appliance end of the inlet hose from

the solenoid inlet valve and remove the flow meter. (In addition re­move the filter using pointed pliers and take out the rubber gasket
behind it.) Re-insert the filter.

2

=1MPa).

31

Water inflow

A 1.50 m long pressure hose is supplied with the appliance.
If a longer water inlet hose is required, only original hoses are to be
used. The Customer Care Department stocks hose kits of different
lengths.

3 Sealing rings are either inserted in the nuts of the threaded hose fitting

or are included as spare parts . Do not use any other type of sealing
rings.

Important! All threaded hose fit­tings must only be tightened by
hand.

1. Connect the hose with the right-an­gle connector to the machine.

Important! Do not position the inlet
hose vertically downwards. Position
it to the right or the left as shown in
the illustration.

2. Connect the hose with the straight
connector to a water tap with an R
¾ (inch) screw thread.

3. To tighten or loosen the threaded
hose fitting, only the metal nuts
must be turned. When doing this,
keep a firm hold on the housing of
the safety valve with one hand, so
that it does not turn at the same
time.
Important! To tighten or loosen the
threaded hose fitting, never turn the
housing of the safety valve, as oth­erwise the inner hose will be dam­aged.

4. Open the water tap slowly and check all connections for water tight­ness.

32

Water drainage

The maximum permitted difference between the height of the surface
on which the appliance is installed and the water outlet is 1 metre.

Only original hoses may be used to extend hoses. (A maximum of 3 m
laid on the floor and then 80 cm vertically). The Customer Care Depart­ment stocks outlet hoses of different lengths.

Draining water into a sink outlet

Secure the outlet/sink outlet joint
with a hose band clip (available from
your dealer).

Draining water into a wash basin/bath

1 Important!

– Small basins are not suitable. Wa-

ter may overflow.

– The end of the drain hose must

not be in the water that has been
pumped out. Otherwise water
could be sucked back into the ap­pliance.

– When draining into a wash basin

or a bath, secure the drain hose
with the supplied elbow to stop it
slipping. Otherwise the water run­ning out can force the hose out of
the basin.

– When pumping the water out,

check that the water is running
away fast enough.

Pumping heights over 1 m

The washing machine’s drain pump is able to pump water to a height of
1meter, calculated from the surface on which the appliance is installed.

Warning! If pumping height is over 1 metre, malfunctions and damage
to the appliance may arise.

For pumping heights over 1metre a conversion kit can be obtained.
Please contact the Customer Care Department.

33

Guarantee/Customer Service

Weitere Kundendienststellen im Ausland

In diesen Ländern gelten die Garantiebedingungen der örtlichen Part­ner. Diese können dort eingesehen werden.

Further after-sales service agencies overseas

In these countries our AEG-Electrolux agents’ own guarantee conditi­ons are applicable. Please obtain further details direct.

Autres agences étrangères assurant le service après-vente

Dans ces pays, les conditions de garantie des concessionnaires de la ré­gion sont valables. Vous pouvez les consulter sur place.

Otros puntos de Postventa en el extranjero

En estos países rigen las condiciones de nuestros representantes locales.
las cuales pueden ser consultadas allí mismo.

Ulteriori uffici del servizio tecnico assistenza clienti all’estero

In questi paesi sono valide le condizioni di garanzia dei partner locali.
Queste condizioni possono essere esaminante sul luogo.

Serviços de assistência técnica no estrangeiro

Nestes países são válidas as condições de garantia dos concessionários
locais, podendo aí ser consultadas.

További vevöszolgálati irodák külföldön

Ezekben az országokban a mi AEG-Electrolux vevöszolgálatainknál
saját jótállási feltételek alkalmazhatók. A további adatokat kérjük
közvetlenül szerezzék be.

34

Servisne službe

Na garancijskem listu boste našli seznam pooblašèenih servisnih
služb AEG-Electrolux.

U.A.E. Abu Dhabi

Universal Trading Company
P.O. Box 43 99
Tel.: [phone]
Service Center 6733974

Egypt

Middle East Commercial
Center
4 Salah El Dein St. - 2nd floor
Heliopolis, Kairo
Egypt
Tel.: [phone]

Jordan

Jordan Household
Supply Co. Ltd.
P.O. Box 3/68
Amman/Tel.: 69 70 50

Canada

EURO-LINE Appliances
2150 Winston PARK Drive 20
Oakville, Ontario L6H 5V1
Tel.: [phone]
Fax: [phone]

Malta

ITC
International Trading Company
White House Building
Mountbatte Street
Blata L-Bajda/Tel.: 220644

Mauritius

Happy World Centre Ltd.
P.O. 7 54
1 Chausee Street
Port Louis
Tel.: 25355

Australia

The Andi-Co Group
1 Stamford Road
Oakleigh VIC 3166
Tel.: [phone]
Fax: [phone]
www.andico.com.au

Bahrain/Arabian Gulf

A.A. Zayani & Sons
P.O. Box 9 3 2
Bahrain
Tel . : [phone]

Bulgaria

Electrolux Bulgaria E.O.O.D.
91 Levski Blvd.
1000 Sofia
Tel.: [phone]
Fax. [phone]

Cyprus

Hadjikyrlakos & Sons Ltd.
Prodromou 121
P.O. Box 21587
Nicosia 1511
Service Telephones:
Nicosia 02 481226
Limassol 05 562182
Larnaca 04 633929
Paphos 06 932 699

Estonia

Electrolux Estonia Ltd.
Mustamäe tee 24
EE0006 Tallinn
Tel.: [phone]
Fax: [phone]

Hong Kong

Dah Chong Hong Ltd.
20 Kai Cheung Road
Kowloon Bay
Kowloon - Hong Kong
Tel.: [phone]
Fax: [phone]

Israel

Evis Ltd.
Tadiran-Ampa Service
10 Gibonay Israel Street
New Industrial Zone
Netanya, 42504
Israel

Korea (South)

Core Incorp.
3/F Chewoo Bldg.
200 Nonhyun-Dong
Kangnam-Ku 135-010
Seoul
Telefon [phone]

Croatia

Electrolux D.O.O.
Suplova 7
10000 Zagreb
Tel.: [phone]
Fax: [phone]

Kuwait/Arabian Gulf

Ali Al-Ghanim Est.
P.O. Box 21540 - Safat
Tel.: [phone]
Fax: [phone]

Lebanon

Adib & Assaferi
P.O. Box 539
Tripoli

Latvia

Electrolux Latvija Ltd.
Kr.Barona iela 130/2
Riga, LV-1012
Tel.: [phone]
Fax: [phone]

Lithuania

Electrolux Lithuania
Verkui 29
2600 Vilnus
Tel.: [phone]
Fax: [phone]

Malaysia

Arzbergh Engineering
No. 49A/B, Jalan Petaling
Utama 7
4600 Petaling Jaya
Tel.: [phone]
Fax: [phone]

Namibia

AEG NAMIBIA (PTY)
LIMITED-Jeppe Street
Northern Industrial Area
Windhoek
Tel.: [phone]
Fax: [phone]

New Zealand

Monaco Corporation Ltd.
10 Rothwell Avenue
Albany - Auckland
4399 Auckland 1
New Zealand
Tel.: [phone]
Fax: [phone]

Syria

WATTAR CO.
P.O. B ox 3 6109
Mazzeh - Damascus
Direct Phone: [phone]
Fax: [phone]

Iran

ARIAN International Develop­ment Co.
AEG Showroom
Shariati, Balatar as Safar
Teheran / Iran
Phone No. Showroom:
021 / 285 513 / 4
Phone No. Service:
021 / 312 27 67 / 8

Poland

Electrolux Poland Sp. zo.o.
ul. Domaniewska 41
02-034 Warszawa
tel.: [phone]
fax: [phone]

Russia

Electrolux Russia Ltd.
16 Olympiysky prospekt
129090 Moscow
Tel.: [phone]
Fax: [phone]

Saudi Arabia

Awad Badi Nahas Est
Shara Siteen
Jeddah 21463
Phone: [phone]
Alia Trading Co
Mecca Road
Riyadh 11491
Phone [phone]

35

Japan

Electrolux Japan Ltd.
Domestic Appliances
Department
Maruzen Showa Warehouse
Building
Tookai 4-5-12, Ota-ku
143-006 Tokyo
Tel.: [phone]
Fax: [phone]

Thailand

Olympia Thai Tower, 444
Rachadapiser Road
Samsennok- Huaykwang
10320 Bangkok
Thailand
Tel.: [phone]
Fax: [phone]

Hungary

Electrolux Lehel KFT
Erzsébet Királyné útja 87.
1142 Budapest
Tel.: [phone]

Singapore

Group Pte Ltd.
833 Bukit Timah Road
Unit no. 01-11 Royalville
279887 Singapore
Tel.: [phone]
Fax: [phone]

Slovakia Rep.

Electrolux Slovakia S.R.O.
Seberiniho 1
821 03 Bratislava
Tel.: [phone], 4355
Fax: [phone]

Czech Rep.

ELECTROLUX DOMÁCå
SPOTØEBIÈE CZ
DIVIZE ELECTROLUX S.R.O.
Customer Centre
Hanusova ul.
140 21 Praha 4
Tel.: [phone]
Telefax: 2 6112 3504

Slovenia

Electrolux Slovenia D.O.O.
Traska Ul. 132
1000 Ljubljana
Tel.: [phone]
Fax: [phone]

South Africa

AEG (Pty) Ltd.
55, 12th Road
P.O. Box 1 02 64
Kew/Johannesburg 2000
Tel.: [phone]

36

373839

Service

In the event of technical faults, please first check whether you can
remedy the problem yourself with the help of the operating instruc­tions (section “What to do if…”).

If you were not able to remedy the problem yourself, please contact the
Customer Care Department or one of our service partners.

In order to be able to assist you
quickly, we require the following
information:

– Model description
– Product number (PNC)
– Serial number (S No.)

(for numbers see rating plate)

– Type of fault
– Any error messages displayed by

the appliance

So that you have the necessary reference numbers from your appliance
at hand, we recommend that you write them in here:

Model description: .....................................

PNC: .....................................

S No: .....................................

From the Electrolux Group. The world´s No.1 choice.

The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more
than 150 countries around the world.

AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg

http://www.aeg-electrolux.de

© Copyright by AEG

105 176 922-01-110106-01

Subject to change without notice