Thank you for choosing this AEG product. We have created it to give you
impeccable performance for many years, with innovative technologies that help
make life simpler – features you might not find on ordinary appliances. Please
spend a few minutes reading to get the very best from it.
Visit our website to:
Get usage advice, brochures, trouble shooter, service and repair information:
www.aeg.com/support
Register your product for better service:
www.registeraeg.com
Buy Accessories, Consumables and Original spare parts for your appliance:
www.aeg.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
ENGLISH3
Subject to change without notice.
1.
SAFETY INFORMATION
Before the installation and use of the appliance,
carefully read the supplied instructions. The
manufacturer is not responsible for any injuries or
damage that are the result of incorrect installation or
usage. Always keep the instructions in a safe and
accessible location for future reference.
1.1 Children and vulnerable people safety
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
www.aeg.com4
• Children between 3 and 8 years of age and persons
with very extensive and complex disabilities shall be
kept away from the appliance unless continuously
supervised.
• Children of less than 3 years of age should be kept
away from the appliance unless continuously
supervised.
• Do not let children play with the appliance.
• Keep all packaging away from children and dispose of
it appropriately.
• Keep detergents away from children.
• Keep children and pets away from the appliance when
the door is open.
• If the appliance has a child safety device, it should be
activated.
• Children shall not carry out cleaning and user
maintenance of the appliance without supervision.
1.2 General Safety
• Do not change the specification of this appliance.
• This appliance is intended to be used in household
and similar applications such as:
– staff kitchen areas in shops, offices and other
working environments;
– by clients in hotels, motels, bed & breakfast and
other residential type environments;
– areas for communal use in blocks of flats or in
launderettes.
• Do not exceed the maximum load of 9 kg (refer to the
"Programme chart" chapter).
• The operating water pressure at the water entry point
from the outlet connection must be between 0.5 bar
(0.05 MPa) and 8 bar (0.8 MPa).
• The ventilation opening in the base must not be
covered by a carpet, mat, or any floor covering.
• The appliance must be connected to the water mains
using the new supplied hose sets, or other new hose
sets supplied by the Authorised Service Centre.
• Old hose sets must not be reused.
• If the mains power supply cable is damaged, it must
be replaced by the manufacturer, its Authorised
Service Centre or similarly qualified persons to avoid
an electrical hazard.
• Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the
socket.
• Do not use high pressure water sprays and/or steam
to clean the appliance.
• Clean the appliance with a moist cloth. Use only
neutral detergents. Do not use abrasive products,
abrasive cleaning pads, solvents or metal objects.
2. SAFETY INSTRUCTIONS
2.1 Installation
The installation must comply
with relevant national
regulations.
• Remove all the packaging and the
transit bolts including rubber bush
with plastic spacer.
• Keep the transit bolts in a safe place.
If the appliance is to be moved in the
future they must be reattached to lock
the drum to prevent an internal
damage.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Follow the installation instructions
supplied with the appliance.
• Do not install or use a damaged
appliance.
• Do not install or use the appliance
where the temperature can be less
than 0°C or where it is exposed to the
weather.
• The floor area on which the appliance
is to be installed must be flat, stable,
heat resistant and clean.
• Make sure that there is air circulation
between the appliance and the floor.
• When the appliance is in its
permanent position, check if it is
levelled correctly with the aid of a
ENGLISH5
spirit level. If it is not, adjust the feet
accordingly.
• Do not install the appliance directly
above a floor drain.
• Do not spray water on the appliance
and do not expose it to excessive
humidity.
• Do not install the appliance where the
appliance door cannot be fully
opened.
• Do not put a closed container to
collect possible water leakage under
the appliance. Contact the Authorised
Service Centre to ensure which
accessories can be used.
2.2 Electrical connection
WARNING!
Risk of fire and electric
shock.
• The appliance must be earthed.
• Always use a correctly installed
shockproof socket.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to
the mains plug and to the mains
cable. Should the mains cable need
www.aeg.com6
to be replaced, this must be carried
out by our Authorised Service Centre.
• Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
• Do not touch the mains cable or the
mains plug with wet hands.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• This appliance is fitted with a 13 A
mains plug. If it is necessary to
change the mains plug fuse, use only
a 13 A ASTA (BS 1362) fuse (UK and
Ireland only).
2.3 Water connection
• Do not cause damage to the water
hoses.
• Before connection to new pipes,
pipes not used for a long time, where
repair work has been carried out or
new devices fitted (water meters, etc.),
let the water flow until it is clean and
clear.
• Ensure that there are no visible water
leaks during and after the first use of
the appliance.
• Do not use an extension hose if the
inlet hose is too short. Contact the
Authorised Service Centre for the
replacement of the inlet hose.
• When unpacking the appliance, It is
possible to see water flowing from the
drain hose. This is due to the testing
of the appliance with the use of water
in the factory.
• You can extend the drain hose to
maximum 400 cm. Contact the
Authorised Service Centre for the
other drain hose and the extension.
• Make sure that there is access to the
tap after the installation.
2.4 Use
WARNING!
Risk of injury, electric shock,
fire, burns or damage to the
appliance.
• Follow the safety instructions on the
detergent packaging.
• Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
• Do not wash fabrics which are heavily
soiled with oil, grease or other greasy
substances. It can damage rubber
parts of the washing machine.
Prewash such fabrics by hand before
loading them into the washing
machine.
• Do not touch the glass door while a
programme operates. The glass can
get hot.
• Make sure that all metal objects are
removed from the laundry.
2.5 Service
• To repair the appliance contact the
Authorised Service Centre. Use
original spare parts only.
• Please note that self-repair or nonprofessional repair can have safety
consequences and might void the
guarantee.
• The following spare parts will be
available for 10 years after the model
has been discontinued: motor and
motor brushes, transmission between
motor and drum, pumps, shock
absorbers and springs, washing drum,
drum spider and related ball bearings,
heaters and heating elements,
including heat pumps, piping and
related equipment including hoses,
valves, filters and aquastops, printed
circuit boards, electronic displays,
pressure switches, thermostats and
sensors, software and firmware
including reset software, door, door
hinge and seals, other seals, door
locking assembly, plastic peripherals
such as detergent dispensers. Please
note that some of these spare parts
are only available to professional
repairers, and that not all spare parts
are relevant for all models.
2.6 Disposal
WARNING!
Risk of injury or suffocation.
• Disconnect the appliance from the
mains electrical and water supplies.
123
9
5
6
7
4
10
8
11 12
ENGLISH7
• Cut off the mains electrical cable
close to the appliance and dispose of
it.
• Remove the door catch to prevent
children or pets from becoming
trapped in the drum.
3. PRODUCT DESCRIPTION
3.1 Special features
Your new washing machine meets all
modern requirements for an effective
treatment of laundry with low water,
energy and detergent consumption and
proper care of fabric.
• The AutoDose technology
automatically dispenses the right
amount of detergent according to the
load; the drawer has two integrated
tanks (detergent + softener) and two
additional compartments for
detergent and additives manual load.
It gives the highest use flexibility.
• The Wi-Fi connection and RemoteStart enable you to start a cycle, to
interact with your washing machine
and to check the washing cycle status
in remote control.
• Dispose of the appliance in
accordance with local requirements
for the disposal of Waste Electrical
and Electronic Equipment (WEEE).
• The ProSense technology detects
the laundry load size defining the
programme duration in 30 seconds.
The washing programme is tailored to
the laundry load and the type of fabric
without consuming more time, energy
and water than necessary.
• The steam has a quick and easy way
to refresh the clothes. The gentle
steam programmes remove odours
and reduce creases in dry fabrics so
they need little ironing.
The Plus Steam option, finishes every
cycle with gentle steam that relaxes
the fibres and reduces fabric creasing.
Ironing will be easier!
• The Intensive option pre-treats
stubborn stains optimizing the
effectiveness of washing performance.
3.2 Appliance overview
Worktop
1
00000000
00A
Mod.
xxxxxxxxx
000V ~ 00Hz 0000 W
910000000
00
A
B
C
Prod.No.
D
www.aeg.com8
Detergent dispenser with AutoDose
2
tanks and manual compartments
Control panel
3
Door handle
4
Rating plate
5
Drain pump filter
6
Feet for levelling the appliance
7
4. TECHNICAL DATA
DimensionWidth/ Height/ Total depth59.7 cm /84.7 cm /66.0 cm
Electrical connectionVoltage
Level of protection against ingress of solid particles and
moisture ensured by the protective cover, except where
the low voltage equipment has no protection against
moisture
Water supply pressure
1)
Overall power
Fuse
Frequency
Minimum
Maximum
Drain hose
8
Inlet hose connection
9
Mains cable
10
Transit bolts
11
Hose support
12
The rating plate reports the model name (A) ,
product number (B), electrical ratings (C) and
serial number (D).
230 V
2200 W
10 A
50 Hz
IPX4
0.5 bar (0.05 MPa)
8 bar (0.8 MPa)
Water supply
Maximum LoadCotton9 kg
Spin SpeedMaximum spin speed1351 rpm
1)
The appliance works correctly if the water pressure is not lower than 0.05 MPa (0.5 bar). If you cannot
connect the water inlet hose to the cold water tap of the primary hydraulic system, connect it to your
domestic cold water storage system. Make sure not to exceed a distance of 5.02 m (16.5 ft) between the
appliance inlet hose and the bottom of the water storage tank.
2)
Connect the water inlet hose to a water tap with a 3/4'' thread.
5. INSTALLATION
2)
WARNING!
Refer to Safety chapters.
Cold water
5.1 Unpacking
1
2
WARNING!
Remove all the packaging
and the transit bolts before
installing the appliance.
WARNING!
Use the gloves.
ENGLISH9
1. Remove the external film. If
necessary, use a cutter.
2. Remove the cardboard top and the
polystyrene packaging materials.
3. Remove the internal film.
5. Carefully put the appliance down on
its rear side.
6. Put the front polystyrene packaging
element on the floor under the
appliance.
Make sure not to
damage the hoses.
7. Remove the polystyrene protection
from the bottom.
4. Open the door and remove the
polystyrene piece from the door seal
and all the items from the drum.
8. Pull up the appliance in vertical
position.
www.aeg.com10
9. Remove the power supply cable and
the drain hose from the hose holders.
It is possible to see
water flowing from the
drain hose. This is due to
the testing with water of
the appliance in factory.
10. Remove the three bolts by using the
spanner supplied with the appliance.
11. Pull out the plastic spacers.
12. Put the plastic caps, that you find in
the user manual bag, in the holes.
We recommend that you
keep the packaging and the
transit bolts for any
movement of the appliance.
5.2 Installation on suspended
flooring
Suspended wooden floors are
particularly susceptible to vibration.
To limit vibration we recommend placing
a waterproof wooden panel, at least 15
mm thick, under the appliance. It should
be screwed to at least 2 floor beams and
should extend beyond the front feet.
If possible, install the appliance where
the floor is more stable.
5.3 Positioning and levelling
1. Install the appliance on a flat hard
floor.
Make sure that carpets do
not stop the air circulation
below the appliance.
Make sure that the appliance
does not touch the wall or
other units.
2. Loosen or tighten the feet to adjust
the level.
WARNING!
Do not put cardboard, wood
or equivalent materials
below the appliance feet to
adjust the level.
x4
20º20º
45º45º
ENGLISH11
The appliance must be level and stable.
A correct adjustment of the
appliance level prevents the
vibration, noise and the
movement of the appliance
when in operation.
When the machine is
installed on a plinth or if a
washer dryer is stacked on
the washing machine, use
the accessories described in
chapter 'Accessories'. Read
carefully the instructions
supplied with the appliance
and with the accessory.
5.4 The inlet hose
1. Connect the water inlet hose to the
back of the appliance.
2. Position it toward left or right
depending on the position of the
water tap.
Make sure that the inlet hose
is not in vertical position.
3. If necessary, loose the ring nut to set
it in the correct position.
4. Connect the water inlet hose to the
cold water tap with 3/4" thread.
CAUTION!
Make sure that there are no
leaks from the couplings.
Do not use an extension
hose if the inlet hose is too
short. Contact the service
centre for the replacement
of the inlet hose.
5.5 Water-stop device
The inlet hose has a water stop device.
This device prevents water leaks in the
hose because of its natural ageing.
The red sector in the window «A» shows
this fault.
A
www.aeg.com12
If this occurs, close the water tap and
contact the authorized service centre to
replace the hose.
5.6 Water drainage
The drain hose should be positioned at a
height of not less than 60 cm and not
more than 100 cm from the floor.
You can extend the drain
hose to maximum 400 cm.
Contact the authorized
service centre for the other
drain hose and the
extension.
It is possible to connect the drain hose in
different ways:
1. Make a U shape with the drain hose
and put it around the plastic hose
guide.
Make sure that the drain
hose end is not immersed in
the water. There may be a
return of dirty water into the
appliance.
3. To a stand pipe with vent-hole Insert the drain hose directly into a
drain pipe. Refer to the illustration.
2. On the edge of a sink - Fasten the
guide to the water tap or to the wall.
Make sure that the plastic
guide cannot move when
the appliance drains.
The end of the drain hose
must always be ventilated ,
i.e. the inner diameter of the
drain pipe (min. 38 mm min. 1.5") must be larger
than the external diameter
of the drain hose.
4. If the end of the drain hose looks like
this (see the picture), you can push it
directly into the stand pipe.
ENGLISH13
5. Without the plastic hose guide, to
a sink spigot - Put the drain hose in
the spigot and tighten it with a
clamp. Refer to the illustration.
Make sure that the drain
hose makes a loop to
prevent particles going into
the appliance from the sink.
6. Position the hose directly to a builtin drain pipe in the room wall and
tighten it with a clamp.
5.7 Electrical connection
At the end of installation you can
connect the mains plug to the mains
socket.
The rating plate and the 'Technical Data'
chapter indicate the necessary electrical
ratings. Make sure that they are
compatible with the mains power supply.
Check that your domestic electrical
installation can take the maximum load
required, also taking into account any
other appliances in use.
Connect the appliance to an earthed
socket.
The power supply cable must be easily
accessible after installing the appliance.
For any electrical work required to install
this appliance, contact our Authorised
Service Centre.
The manufacturer does not accept any
responsibility for damage or injury
through failure to comply with the above
safety precaution.
6. ACCESSORIES
6.1 Available in
www.aeg.com/shop or from
authorised dealer
Read carefully the instructions supplied
with the accessory.
Only appropriate
accessories approved by
AEG ensure the safety
standards of the appliance. If
unapproved parts are used,
any claims will be
invalidated.
6.2 Fixing plate kit
If you install the appliance on a plinth,
secure the appliance with the fixing
plates.
Read carefully the instructions supplied
with the accessory.
6.3 Stacking kit
The tumble dryer can be stacked on the
top of the washing machine only byusing the correct stacking kit.
s
citehtn
y
S
s
etacil
e
D
kl
iS
/
looW
ma
et
S
y
g
rel
l
a-itnA
roodt
u
O
s
n
aeJ
gk3 nim02
P
rewash
Int
ensi
ve
Only Spi
n
T
emperature
Spin
T
ime Save
Intensive/
P
rewash
Only
Drain
St
eam Pl
us
S
tar
t
/
Pause
Delay
S
t
art
Program
Eco 40 -60
C
o
ttons
2
3
6
1211 10
8
1
4
5
7
9
www.aeg.com14
6.4 Pedestal with the drawer
WARNING!
Do not put the tumble dryer
under the washing machine.
Verify the compatible
stacking kit by checking the
depth of your appliances.
7. CONTROL PANEL
7.1 Control panel description
The options are not selectable with all washing programmes. Check the
compatibility between options and washing programmes in the
"AutoDose and options compatibility with programmes" paragraph in the
"Programmes" chapter. An option can exclude another one, in this case
the appliance doesn't allow you to set the incompatible options together.
Make sure the screen and touch buttons are always clean and dry.
To raise your appliance and make
loading and unloading laundry easier.
The drawer can be used for laundry
storage e.g.: towels, cleaning products
and more.
1
2
3
4
5
6
ENGLISH15
Programme di-alFor selecting the desired washing programme. Refer to "Pro-
grammes" chapter for more details.
Display
It provides information about the setting programme. Refer to
"Display" paragraph for more details.
For activating and deactivating the automatic detergent loading.
AutoDose Liquid Detergent
Refer to "The AutoDose Technology (Autodosing)" chapter for
more details.
touch button
For activating and deactivating the automatic fabric softener load-
AutoDose Fabric Softener
ing. Refer to "The AutoDose Technology (Autodosing)" chapter
for more details.
touch button
With this option you can decrease the programme duration:
Daily
•
If your laundry is normally or lightly soiled, it may be advisable
to shorten the washing programme. Touch this button once to
decrease the duration.
Time Save
touch button
•Super Quick
In case of smaller load, touch this button twice to set an extra
quick programme.
This option can also be used to shorten the
Steam programme duration.
Start/Pause
touch button
Touch this button to start, pause the appliance or interrupt a running programme.
7
www.aeg.com16
Press this button repeatedly to activate one of the two options or
both.
The relevant indicator comes on.
•Intensive
Intesive/
Prewash touch
button
By setting this option, the indicator
gent symbol, and the appliance will automatically dose an extra amount of detergent when automatic detergent tank is enabled.
If automatic detergent tank is Off, it is possible to run this option as in traditional washing machine by filling detergent or
additive in the manual compartment.
If you press detergent tank button while Inten-
appears close to deter-
sive option is active, AutoDose function is
switched off, but Intensive option still remains
active in manual mode.
•Prewash
Use this option to add a pre-wash phase at 30 °C before the
washing phase.
This option is recommended for heavily soiled laundry, especially if containing sand, dust, mud and other solid particles.
When selecting a pre-wash phase and AutoDose is active, the appliance will automatically
dose the detergent. When AutoDose is switched off, put the detergent/additive in a dosing
ball inside the drum.
The options can increase the programme duration.
8
Remote/Delay
9
Start touch
button
Plus Steam
touch button
ENGLISH17
Press this button repeatedly to activate one of the two options or
both.
The relevant indicator comes on in the display.
•Remote
Select this option to connect appliance with App.
Touch this button, the display shows the indicator blinking for a few seconds.
After touching the Start/Pause button, the display shows the
indicator and the Remote is confirmed.
When touching the Start/Pause button after
the indicator
stops blinking, the Remote
Start is not activated, but the set programme
starts.
•
Delay Start
With this option you can delay the start of a programme in a
more convenient time.
Touch the button repeatedly to set the required delay. The
time increases by steps of 30 minutes up to 90' and from 2
hours up to 20 h.
After touching the Start/Pause button, the display shows the
indicator and the selected delay time and the appliance
begins the countdown.
This option adds a steam phase followed by a short anti-crease
phase at the end of the washing programme.
The steam phase reduces fabric creasing and facilitates the fabric
ironing.
The indicator
flashes on the display during steam phase.
This option can increase the programme duration.
When the programme stops the display shows a zero
cator
drum performs smooth movements for about 30 minutes to keep
the steam benefit. By touching any button the anti-crease movements stop and the door unlocks.
is steady on and the indicator starts flashing. The
, the indi-
A small laundry load helps to reach better results.
10
www.aeg.com18
When you set a programme, the appliance automatically selects
the maximum spin speed.
Touch this button repeatedly to:
• Decrease the spin speed.
The display shows only the spin speeds available for the set programme.
•
Activate the Rinse Hold option .
The water of the last rinse is not drained out to prevent the
fabrics from creasing. The washing programme ends with water in the drum and the final spin phase is not performed.
. The door stays locked.
. The door stays locked. The
Spin touch button
The display shows the indicator
The drum turns regularly to reduce creasing. You must drain
the water to unlock the door.
Touch Start/Pause button: the appliance performs the spinning
phase and drains the water.
•Activate the Quiet option.
All spinning phases (intermediate spin and final spin) are suppressed and the programme ends with water in the drum. This
helps to reduce creasing.
As the programme is very quiet, it is suitable for use at night
time when cheaper electricity tariffs are available. In some programmes the rinses are performed with more water.
The display shows the indicator
drum turns regularly to reduce creasing. You must drain the
water to unlock the door.
Touch the Start/Pause button button: the appliance performs
only the draining phase.
The appliance empties the water out automatically after approximately 18 hours.
Loading...
+ 42 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.