AEG L50843 User Manual

LAVAMAT 50843

User manual Washing Machine

2 Contents

Thank you for choosing one of our high-quality products.

To ensure optimal and regular performance of your appliance please read this
instruction manual carefully. It will enable you to navigate all processes perfectly
and most efficiently. To refer to this manual any time you need to, we recommend
you to keep it in a safe place. And please pass it to any future owner of the
appliance.

We wish you much joy with your new appliance.

CONTENTS

OPERATING INSTRUCTIONS 3

SAFETY INFORMATION 3

General safety 3
Installation 3
Use 4
Child Safety 4

PRODUCT DESCRIPTION 5

Detergent dispenser drawer 6

CONTROL PANEL 6

Indicator pilot lights (7) 7

FIRST USE 7
DAILY USE 7

Load the laundry 7
Measure out the detergent and the fabric
softener 7
Select the required programme by means of
programme selector dial (1) 8
Select the SPIN speed or the RINSE HOLD
option (Button 2) 8
Programme option button 9
Select the STAIN option (Button 3) 9
Select the SUPER QUICK option (Button 4)

Select the START/PAUSE (Button 5) 9
Select the DELAY START (Button 6) 9
Select an additional rinse 10
Interrupting a programme 10
Cancelling a programme 10
Altering an option or a running programme

10

At the end of the programme 10

WASHING PROGRAMMES 11
HELPFUL HINTS AND TIPS 13

Sorting out the laundry 13
Before loading the laundry 13
Removing stains 14
Detergents and additives 14
Quantity of detergent to be used 15
Degrees of water hardness 15

CARE AND CLEANING 15

Descaling 15
After each wash 15
Maintenance wash 15
External cleaning 16
Detergent dispenser drawer 16
Washing drum 16
Door seal 17
Drain pump 17
Cleaning the water inlet filters 19
Emergency emptying out 20
Frost precautions 20

WHAT TO DO IF… 20
TECHNICAL DATA 24
CONSUMPTION VALUES 24

INSTALLATION INSTRUCTIONS 24

9

INSTALLATION 24

Unpacking 24
Positioning and levelling 27
Rubber feet kit (4055126249) 27
Water inlet 27
Water drainage 28

ELECTRICAL CONNECTION 29
ENVIRONMENT CONCERNS 29

Packaging materials 30
Ecological hints 30

Subject to change without notice

Safety information

OPERATING INSTRUCTIONS

SAFETY INFORMATION

Read carefully & keep for future reference.

• The safety of Your appliance complies with the industry standards and with legal re­quirements on the safety of appliances. However, as manufacturers, we feel it is our duty
to provide the following safety notes.

• It is most important that this instruction book should be retained with the appliance for
future reference. Should the appliance be sold or transferred to another owner, or should
you move house and leave the appliance, always ensure that the book is supplied with
the appliance in order that the new owner can get to know the functioning of the appli­ance and the relevant warnings.

• You MUST read them carefully before installing or using the appliance.

• Before first starting up, check the appliance for any damage incurred during transport.
Never connect up a damaged appliance . If parts are damaged, contact your supplier.

• If the appliance is delivered in the winter months when there are minus temperatures.
Store it at room temperature for 24 hours before using for the first time.

General safety

• It is dangerous to alter the specifications or attempt to modify this product in any way.

• During high temperature wash programmes the door glass may get hot. Do not touch it!

• Make sure that small pets and children do not climb into the drum. To avoid this, please
check into the drum before using.

• Any objects such as coins, safety pins, nails, screws, stones or any other hard, sharp ma­terial can cause extensive damage and must not be placed into the machine.

• Only use the advised quantities of fabric softener and detergent. Damage to the fabric
can ensue if you over-fill. Refer to the manufacturer’s recommendations of quantities.

• Wash small items such as socks, laces, washable belts etc in a washing bag or pillow case
as it is possible for such items to slip down between the tub and the inner drum.

• Do not use your washing machine to wash articles with whalebones, material without
hems or torn material.

• Always unplug the appliance and turn off the water supply after use, cleaning and main­tenance.

• Under no circumstances should you attempt to repair the machine yourself. Repairs car­ried out by inexperienced people may cause injury or serious malfunctioning. Contact
your local Service Centre. Always insist on genuine spare parts.

3

Installation

• This appliance is heavy. Care should be taken when moving it.

• When unpacking the appliance, check that it is not damaged. If in doubt, do not use it
and contact the Service Centre.

4 Safety information

• All packing and transit bolts must be removed before use. Serious damage can occur to
the product and to property if this is not adhered to. See relevant section in the user
manual.

• After having installed the appliance, check that it is not standing on the inlet and drain
hose and the worktop is not pressing the electrical supply cable against the wall.

• If the machine is situated on a carpeted floor, please adjust the feet in order to allow air
to circulate freely under the appliance.

• Always be sure, that there is no water leakage from hoses and their connections after the
installation.

• If the appliance is installed in a location subject to frost, please read the “dangers of
freezing” chapter.

• Any plumbing work required to install this appliance should be carried out by a qualified
plumber or competent person.

• Any electrical work required to install this appliance should be carried out by a qualified
electrician or competent person.

Use

• This appliance is designed for domestic use. It must not be used for purposes other than
those for which it was designed.

• Only wash fabrics which are designed to be machine washed. Follow the instructions on
each garment label.

• Do not overload the appliance. See the Washing Programme Table.

• Before washing, ensure that all pockets are empty and buttons and zips are fastened.
Avoid washing frayed or torn articles and treat stains such as paint, ink, rust, and grass
before washing. Underwired bras must NOT be machine washed.

• Garments which have been in contact with volatile petroleum products should not be
machine washed. If volatile cleaning fluids are used, care should be taken to ensure that
the fluid is removed from the garment before placing in the machine.

• Never pull the power supply cable to remove the plug from the socket; always take hold
of the plug itself.

• Never use the appliance if the power supply cable, the control panel, the working surface
or the base are damaged so that the inside of the washing machine is accessible.

Child Safety

• This appliance is not intended for use by person (including children) with reduced physi­cal sensory or mental capabilities or lack of experience and knowledge unless they have
been given supervision or instruction concerning use of the appliance by a person re­sponsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• The packaging components (e.g. plastic film, polystyrene) can be dangerous to children ­danger of suffocation! Keep them out of children's reach.

• Keep all detergents in a safe place out of children’s reach.

Product description 5

• Make sure that children or pets do not climb
inside the drum. To prevent children or pets
becoming trapped inside the drum the ma­chine incorporates a special feature. To acti­vate this device, rotate the button (without
pressing it) inside the door clockwise until
the groove is horizontal. If necessary use a
coin. To disable this device and restore the
possibility of closing the door, rotate the
button anticlockwise until the groove is ver­tical.

PRODUCT DESCRIPTION

Your new appliance meets all modern requirements for effective treatment of laundry with
low water, energy and detergent consumption.
The ECO valve system allows total use of detergent and reduces water consumption so sav­ing energy.

2

1

6

1 Detergent dispenser drawer
2 Control panel
3 Door opening handle
4 Rating plate
5 Drain pump
6 Adjustable feet

3

4

5

6 Control panel

Detergent dispenser drawer

Compartment for prewash phase or stain re-

mover.
The prewash detergent is added at the beginning
of the wash programme.
The stain remover is added during the STAIN-Ac-
tion phase in the main wash.

Compartment for powder or liquid detergent

used for main wash.

Compartment for liquid additives (fabric soft-

ener, starch).
Follow the product manufacturer’s recommendations on quantities to use and do not ex-

ceed the «MAX» mark in the detergent dispenser drawer. Any fabric softener or starching
additives must be poured into the compartment before starting the wash programme.

CONTROL PANEL

1

1 Programme selector dial
2 Spin reduction button (GIRI/MIN.)
3 STAIN button (MACCHIE)
4 SUPER QUICK button (RISP.TEMPO)
5 START/PAUSE button (AVVIO/PAUSA)
6 DELAY START button (PARTENZA RITARDATA)
7 Indicator lights:

– Washing (LAVAGGIO)
–End (FINE)
– Extra rinse (RISCIACQUO +)

Table of symbols

= Handwash

4

3

2

5

7

6

Indicator pilot lights (7)

When you press the button 5, the pilot light
WASHING (7.1) comes on. The appliance operates
and you cannot open the door.
When the programme completes, the pilot light
END (7.2) comes on and after some minutes you
can open the door.
When the appliance does the additional rinses,
the pilot light EXTRA RINSE (7.3) comes on. See
«Select an additional rinse».

FIRST USE

• Ensure that the electrical and water connections comply with the installation instruc­tions.

• Remove the polystyrene block and any material from the drum.

• Pour 2 litres of water into the main wash compartment
order to activate the ECO valve. Then run a cotton cycle at the highest temperature
without any laundry in the machine, to remove any manufacturing residue from the
drum and tub. Pour 1/2 a measure of detergent into the main wash compartment and
start the machine.

of the detergent drawer in

First use 7

DAILY USE

Load the laundry

1. Open the door by carefully pulling the

door handle outwards. Place the laundry
in the drum, one item at a time, shaking
them out as much as possible.

2. Close firmly the door. You must hear a

click during closing.

WARNING!

Do not embed the laundry between the door
and the rubber joint.

Measure out the detergent and the fabric softener

Your new appliance was designed to reduce water, energy and detergent consumption.

8 Daily use

1. Pull out the dispenser drawer until it

stops. Measure out the amount of de­tergent required, pour it into the main
wash compartment
to carry out the prewash phase or to
perform the stain function, pour the
detergent or the stain remover into the
compartment marked

2. If required, pour fabric softener into the

compartment marked
used must not exceed the MAX mark in
the drawer). Close the drawer gently.

and, if you wish

.

(the amount

Select the required programme by means of programme selector dial (1)

You can choose the right programme for any type of laundry following the descriptions on
the washing programme tables (see «Washing Programmes»).
Turn the programme selector dial to the required programme. The programme selector de­termines the type of washing cycle (e.g. water level, drum movement, number of rinses) and
the washing temperature according to the type of laundry.
The pilot light of button 5 starts blinking.

The selector dial can be turned either clockwise or anticlockwise. Position
gramme/ Switching OFF of the machine.

At the end of the programme the selector dial must be turned to position
switch the machine off.

If you turn the programme selector dial to another programme when the machine is work­ing, the yellow pilot light of button 5 will blink 3 times to indicate a wrong selection. The
machine will not perform the new selected programme.

to Reset pro-

Select the SPIN speed or the RINSE HOLD option (Button 2)

When the required programme has been selected, your appliance automatically proposes
the maximum spin speed provided for that programme.

, to

Daily use

Press the button 2 repeatedly to change the spin speed, if you want your laundry to be
spun at a speed different from the one proposed by the washing machine.
The relevant light will light up.
RINSE HOLD : by selecting this option the water of the last rinse is not emptied out to pre­vent the fabrics from creasing. When the programme has finished the pilot light 7.2 goes
on, the pilot light of button 5 and the pilot light (7.1) are off and the door is blocked to
indicate that the water must be emptied out.

To empty the water out please read chapter «At the end of the programme».

Programme option button

Depending on the programme, different functions can be combined. These must be selected
after choosing the desired programme and before depressing the button 5 . When these
buttons are pressed, the corresponding pilot lights come on. When they are pressed again,
the pilot lights go out.
If an incorrect option is selected, the yellow pilot light of the button 5 blinks for 3 times.
For the compatibility among the washing programmes and the options see chapter «Wash­ing Programmes».

Select the STAIN option (Button 3)

Select this option to treat heavily soiled or stained laundry with stain remover (extended
main wash with time optimized stain action phase). The relevant light will light up.
This option is not available with a temperature lower than 40°C.

CAUTION!

If you wish to perform a programme with the stain option, pour stain remover into com­partment

.

9

Select the SUPER QUICK option (Button 4)

By pressing this button, the relevant pilot light comes on and the washing duration will be
reduced to wash lightly soiled laundry. This option is suitable for items that have been used
or worn for a short time.

Select the START/PAUSE (Button 5)

To start the selected programme, press the button 5 ; the corresponding red pilot light
stops flashing.
The pilot light 7.1 is on to indicate that the appliance starts operating and the door is
locked.
To interrupt a programme which is running, press the button 5 : the corresponding red pi­lot light starts blinking.
To restart the programme from the point at which it was interrupted, press the button 5
again.
If you have chosen a delayed start, the machine will begin the countdown.

Select the DELAY START (Button 6)

Before you start the programme, if you wish to delay the start, press the button 6 re­peatedly, to select the desired delay. The relevant light illuminates. This button makes it
possible to delay the starting of the washing programme by 3, 6 and 9 hours.

10 Daily use

You must select this option after you have set the programme and before you press the
button 5.
You can cancel the delay time at any moment, before you press the button 5.
If the button 5 has already been pressed:

• set the washing machine to PAUSE by pressing the button 5;

• press the button 6 once, the light relevant to the selected delay goes off;

• press the button 5 again to start the programme.

Important!

• The selected delay can be changed only after selecting the washing programme again.

• The door will be locked throughout the delay time. If you need to open the door, you
must first set the washing machine to PAUSE by pressing the button 5 and then wait
some minutes. After you have closed the door, press the button 5 again.

The DELAY START can not be selected with DRAIN programme.

Select an additional rinse

This appliance is designed for saving water. However, for people with a very delicate skin
(allergic to detergents) it may be necessary to rinse the laundry using an extra quantity of
water (extra rinse).
Press simultaneously button 2 and 3 for a few seconds: the light 7.3 comes on. This func-
tion stays permanently on. To remove it press the same buttons again until the light 7.3
goes off.

Interrupting a programme

Press the button 5 to interrupt a programme which is running, the corresponding light
starts blinking. Press the button again to restart the programme.

Cancelling a programme

Turn the selector dial to to cancel a programme which is running. Now you can select a
new programme.

Altering an option or a running programme

It is possible to change any option before the programme carries it out. Before you make
any change, you must pause the washing machine by pressing the button 5.
Changing a running programme is possible only by resetting it. Turn the programme se-

lector dial to
pressing the 5 button again. The washing water in the tub will not emptied out.

and then to the new programme position. Start the new programme by

At the end of the programme

The machine stops automatically. The light of button 5 and the light 7.1 go off. The phase
light 7.2 illuminates.
If you have set a programme or an option that ends with water in the tub, the correspond­ing pilot light remains lit. The phase light 7.2 goes on. The door remains locked. The water
must be emptied out before opening the door. During this time, the drum continues to turn
at regular intervals until water drain.

To empty the water out:

•

turn the programme selector dial to

• select the DRAIN or SPIN programme

• if necessary, reduce the spin speed if needed

• press button 5

• when the programme has finished only the pilot light 7.2 comes on.

Turn the programme selector dial to

position to switch the machine off. Remove the
laundry from the drum and carefully check that the drum is empty.
If you do not intend to carry out another wash, close the water tap. Leave the door open to
prevent the formation of mildew and unpleasant smells.

Stand by: once the programme has finished after a few minutes the energy saving system
is enabled with the pilot lights switched on. By pressing any button the appliance will come
out of the energy saving status.

WASHING PROGRAMMES

11

Programme - Maximum and Minimum Temperature ­Cycle Description - Maximum Spin Speed - Maximum
Fabrics Load - Type of Laundry

COTONI BIANCHI COLORATI

95° - 30°
Main wash - Rinses - Long spin
Spin at maximum speed
Max. load 6 kg - Reduced load 3 kg
For white and fast coloured cotton (heavily and
normally soiled items).

COTONI CON PRELAVAGGIO

60° - 40°
Prewash - Main wash - Rinses - Long spin
Spin at maximum speed
Max. load 6 kg - Reduced load 3 kg
White or coloured cottons with prewash phase
(heavily soiled items).

SINTETICI

60°- 30°
Main wash - Rinses - Short spin
Maximum spin speed at 900 rpm
Max. load 3 kg - Reduced load 1,5 kg
Synthetic or mixed fabrics: underwear, coloured
garments, non-shrink shirts, blouses.

Options

SPIN REDUCTION

NO CENTRIFUGA FINALE

RISPARMIO TEMPO

RISCIACQUO+

SPIN REDUCTION

NO CENTRIFUGA FINALE

RISPARMIO TEMPO

RISCIACQUO +

SPIN REDUCTION

NO CENTRIFUGA FINALE

RISPARMIO TEMPO

RISCIACQUO +

STAINS

STAINS

1)

2)

2)

1)

2)

Detergent

Compartment

3)

12 Washing programmes

Programme - Maximum and Minimum Temperature ­Cycle Description - Maximum Spin Speed - Maximum
Fabrics Load - Type of Laundry

FACILE STIRO PLUS

40°
Main wash - Rinses - Short spin
Maximum spin speed at 900 rpm
Max. load 1 kg

Synthetic fabrics to be gentle washed and spun.

Selecting this programme the laundry is gently
washed and spun to avoid any creasing. In this way
ironing is easier. Furthermore the machine will per­form additional rinses.

DELICATI

40°- 30°
Main wash - Rinses - Short spin
Spin at maximum speed
Max. load kg 3 - Reduced load kg 1,5

Delicate fabrics: acrylics, viscose, polyester.

LANA PLUS - HANDWASH

30°- Cold
Main wash - Rinses - Short spin
Maximum spin speed at 1000 rpm
Max. load 2 kg
A special washing programme for machine washable
wool and silk items as well as for hand washable
woollens and silk fabrics with handwash label. Note :
A single or bulky item may cause imbalance. If the
appliance doesn’t perform the final spin phase, add
more items, redistribute the load manually and then
select the spinning programme.

RISCIACQUI

Rinses - Short spin
Maximum spin speed at 900 rpm
Max. load 6 kg
With this programme it is possible to rinse and spin
cotton garments which have been washed by hand.
The machine performs some rinses, followed by a fi­nal spin.

SCARICO

Draining of water
Max. load 6 kg
For emptying out the water of the last rinse in pro­grammes with the Rinse Hold option selected.

Options

SPIN REDUCTION

NO CENTRIFUGA FINALE

RISCIACQUO +

SPIN REDUCTION

NO CENTRIFUGA FINALE

1)

STAINS

RISPARMIO TEMPO

2)

RISCIACQUO +

SPIN REDUCTION

NO CENTRIFUGA FINALE

SPIN REDUCTION

NO CENTRIFUGA FINALE

RISCIACQUO +

Detergent

Compartment

Helpful hints and tips

13

Programme - Maximum and Minimum Temperature ­Cycle Description - Maximum Spin Speed - Maximum
Fabrics Load - Type of Laundry

CENTRIFUGA

Drain and long spin
Spin at maximum speed
Max. load 6 kg
Separate spin for hand washed cotton garments and
after programmes with the Rinse Hold option selec­ted. Before selecting this programme the selector dial

must be turned to
speed by pressing the relevant button to adapt it to
the fabrics to be spun.

REFRESH

30°
Main wash - Rinses - Short spin
Maximum spin speed at 700 rpm
Max. load 3 kg
This programme may be used for a quick washing of
sport items or cotton and synthetic items , lightly
soiled or worn once.

RISPARMIO ENERGIA

60° - 40°
Main wash - Rinses - Long spin
Spin at maximum speed
Max. load 6 kg
White and fast coloured cotton.
This programme can be selected for slightly or nor­mally soiled cotton items. The temperature will de­crease and the washing time will be extended. This
allows to obtain a good washing efficiency so saving
energy.

/ OFF
For cancelling the programme which is running or to
switch the machine off .

1) This option is not available with a temperature lower than 40°C.

2) If you select the RISPARMIO TEMPO option (button 4), we recommend that you reduce the maximum load as
indicated. Full loading is possible however with somewhat reduced cleaning results.

3) If using liquid detergents, a programme without prewash must be selected.

. You can choose the spin

Options

SPIN REDUCTION

SPIN REDUCTION

SPIN REDUCTION

NO CENTRIFUGA FINALE

STAINS

RISCIACQUO +

Detergent

Compartment

HELPFUL HINTS AND TIPS

Sorting out the laundry

Follow the wash code symbols on each garment label and the manufacturer’s washing in­structions. Sort the laundry as follows: whites, coloureds, synthetics, delicates, woollens.

Before loading the laundry

Never wash whites and coloureds together. Whites may lose their «whiteness» in the wash.

14 Helpful hints and tips

New coloured items may run in the first wash; they should therefore be washed separately
the first time.
Button up pillowcases, close zip fasteners, hooks and poppers. Tie any belts or long tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special detergent or detergent paste.
Treat curtains with special care. Remove hooks or tie them up in a bag or net.

Removing stains

Stubborn stains may not be removed by just water and detergent. It is therefore advisable
to treat them prior to washing.
Blood: treat fresh stains with cold water. For dried stains, soak overnight in water with a
special detergent then rub in the soap and water.
Oil based paint: moisten with benzine stain remover, lay the garment on a soft cloth and
dab the stain; treat several times.
Dried grease stains: moisten with turpentine, lay the garment on a soft surface and dab
the stain with the fingertips and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a rust removing product used cold. Be careful
with rust stains which are not recent since the cellulose structure will already have been
damaged and the fabric tends to hole.

Mould stains: treat with bleach, rinse well (whites and fast coloureds only).
Grass: soap lightly and treat with bleach (whites and fast coloureds only).

Ball point pen and glue: moisten with acetone

the stain.
Lipstick: moisten with acetone as above, then treat stains with methylated spirits. Treat
any residual marks with bleach.
Red wine: soak in water and detergent, rinse and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.

Ink: depending on the type of ink, moisten the fabric first with acetone
acid; treat any residual marks on white fabrics with bleach and then rinse thoroughly.
Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with de­tergent paste.

1)

, lay the garment on a soft cloth and dab

1)

, then with acetic

Detergents and additives

Good washing results also depend on the choice of detergent and use of the correct quan­tities to avoid waste and protect the environment.
Although biodegradable, detergents contain substances which, in large quantities, can up­set the delicate balance of nature.
The choice of detergent will depend on the type of fabric (delicates, woollens, cottons, etc.),
the colour, washing temperature and degree of soiling.
All commonly available washing machine detergents may be used in this appliance:

• powder detergents for all types of fabric

• powder detergents for delicate fabrics (60°C max) and woollens

• liquid detergents, preferably for low temperature wash programmes (60°C max) for all

types of fabric, or special for woollens only.
The detergent and any additives must be placed in the appropriate compartments of the
dispenser drawer before starting the wash programme.

1) do not use acetone on artificial silk

Care and cleaning

If using liquid detergents, a programme without prewash must be selected.
Your appliance incorporates a recirculation system which allows an optimal use of the con­centrated detergent.
Follow the product manufacturer’s recommendations on quantities to use and do not ex­ceed the «MAX» mark in the detergent dispenser drawer.

Quantity of detergent to be used

The type and quantity of detergent will depend on the type of fabric, load size, degree of
soiling and hardness of the water used.
Follow the product manufacturers’ instructions on quantities to use.
Use less detergent if:

• you are washing a small load

• the laundry is lightly soiled

• large amounts of foam form during washing.

Degrees of water hardness

Water hardness is classified in so-called “degrees” of hardness. Information on hardness of
the water in your area can be obtained from the relevant water supply company, or from
your local authority. If the water hardness degree is medium or high we suggest you to add
a water softener following always the manufacturer’s instructions. When the degree of
hardness is soft, readjust the quantity of the detergent.

CARE AND CLEANING

15

You must DISCONNECT the appliance from the electricity supply, before you can carry out
any cleaning or maintenance work.

Descaling

The water we use normally contains lime. It is a good idea to periodically use a water soft­ening powder in the machine. Do this separately from any laundry washing, and according
to the softening powder manufacturer's instructions. This will help to prevent the forma­tion of lime deposits.

After each wash

Leave the door open for a while. This helps to prevent mould and stagnant smells forming
inside the appliance. Keeping the door open after a wash will also help to preserve the door
seal.

Maintenance wash

With the use of low temperature washes it is possible to get a build up of residues inside
the drum.
We recommend that a maintenance wash be performed on a regular basis.
To run a maintenance wash:

• The drum should be empty of laundry.

• Select the hottest cotton wash programme.

• Use a normal measure of detergent, must be a powder with biological properties.

16 Care and cleaning

External cleaning

Clean the exterior cabinet of the appliance with soap and water only, and then dry thor­oughly.

Do not use methylated spirits, solvents or similar products to clean the cabinet.

Detergent dispenser drawer

The detergent dispenser drawer should be cleaned regularly.

1. Remove the detergent dispenser drawer by pulling it firmly.

2. Remove the conditioner insert from the

middle compartment.

3. Clean all parts with water.

4. Put the conditioner insert in as far as it

will go, so that it is firmly in place.

5. Clean all parts of the washing machine,

especially the nozzles in the top of the
washing-in chamber, with a brush.

6. Insert the detergent dispenser drawer in

the guide rails and push it in.

Washing drum

Rust deposits in the drum may occur due to rusting foreign bodies in the washing or tap
water containing iron.

Do not clean the drum with acidic descaling agents, scouring agents containing chlorine or
iron or steel wool.

1. Remove any rust deposits on the drum with a cleaning agent for stainless steel.

2. Run a washing cycle without any washing to clean off any cleaning agent residues.

Programme: Short Cotton Programme at maximum temperature and add approx. 1/4
measuring cup of detergent.

Care and cleaning 17

Door seal

Check from time to time the door seal and objects
that could be trapped in the fold.

Drain pump

The pump should be inspected regularly and particularly if:

• the appliance does not empty and/or spin;

• the appliance makes an unusual noise during draining due to objects such as safety pins,

coins etc. blocking the pump;

• a problem with water draining is detected (see chapter “What to do if...” for more de-

tails).

WARNING!

Before opening the pump door, switch the appliance off remove the mains plug from the
socket.

Proceed as follows:

1. Unplug the appliance.

2. If necessary wait until the water has cooled down.

3. Open the pump door.

4. Pull flap forward to remove.

5. Place a container close to the pump to

collect any spillage.

6. Pull out the emergency emptying hose,

place it in the container and remove its
cap.

18 Care and cleaning

7. When no more water comes out, un-

screw the pump cover by turning it an­ti-clockwise and remove the filter. Use
pliers, if necessary. Always keep a rag
nearby to dry up any water spillages
when removing the cover.

Clean the filter under a tap, to remove
any traces of fluff.

8. Remove foreign bodies and fluff from

the filter seat and from the pump im­peller.

9. Check carefully whether the pump im-

peller rotates (it rotates jerkily). If it
doesn’t rotate, please contact your Serv­ice Centre.

10. Put the cap back on the emergency

emptying hose and place the latter back
in its seat.

11. Replace the filter into the pump by in-

serting it correctly into the special
guides. Screw the pump cover firmly by
turning it clockwise.

12. Refit the flap and close the pump door.

WARNING!

When the appliance is in use and depending on the programme selected there can be hot
water in the pump.
Never remove the pump cover during a wash cycle, always wait until the appliance has fin­ished the cycle, and is empty. When refitting the pump cover, ensure it is securely re-tight­ened so as to stop leaks and young children being able to remove it.

Care and cleaning 19

Cleaning the water inlet filters

If the appliance doesn't fill, it takes a long time to fill with water, the starting button blinks
yellow or the display (if available) shows the relevant alarm (see chapter "What to do if..."
for more details), check if the water inlet filters are blocked .

To clean the water inlet filters:

1. Turn off the water tap.

2. Unscrew the hose from the tap.

3. Clean the filter in the hose with a stiff

brush.

4. Screw the hose back onto the tap. Make

sure the connection is tight.

5. Unscrew the hose from the machine.

Keep a towel nearby because some wa­ter may flow.

6. Clean the filter in the valve with a stiff

brush or with the piece of cloth.

7. Screw the hose back to the machine and

make sure the connection is tight.

8. Turn on the water tap.

20 What to do if…

Emergency emptying out

If the water is not discharged, proceed as follows to empty out the machine:

1. pull out the plug from the power socket;

2. close the water tap;

3. if necessary, wait until the water has cooled down;

4. open the pump door;

5. place a bowl on the floor and place the end of the emergency emptying hose into the

bowl. Remove its cap. The water should drain by gravity into the bowl. When the bowl
is full, put the cap back on the hose. Empty the bowl. Repeat the procedure until water
stops flowing out;

6. clean the pump if necessary as previously described;

7. replace the emergency emptying hose in its seat after having plugged it;

8. screw the pump again and close the door.

Frost precautions

If the machine is installed in a place where the temperature could drop below 0°C, proceed
as follows:

1. close the water tap and unscrew the water inlet hose from the tap;

2. place the end of the emergency emptying hose and that of the inlet hose in a bowl

placed on the floor and let water drain out;

3. screw the water inlet hose back on and reposition the emergency emptying hose after

having put the cap on again.
By doing this, any water remaining in the machine is removed, avoiding ice forming and
consequently damage to the appliance.
When you use the machine again, make sure that the ambient temperature is above 0°C.

Every time you drain the water through the emergency emptying hose you must pour 2
litres of water into the main wash compartment of the detergent drawer and then run the
drain programme. This will activate the ECO Valve device avoiding that part of the deter­gent remains unused at next washing.

WHAT TO DO IF…

Certain problems are due to lack of simple maintenance or oversights, which can be solved
easily without calling out an engineer. Before contacting your local Service Centre, please
carry out the checks listed below.
During machine operation it is possible that the pilot light of button 5 blinks to indicate
that the machine is not working.
It is possible to recognize the machine fault by the number of button 5 light flashes. If the
number of flashes is different from the ones indicated below, this is related to a fault that
you cannot solve. In this case, contact your local Service Centre.
Press simultaneously the buttons 4 and 5 for a few seconds. The yellow button 5 light will
flash for a short time as described (the green flash is not to be considered) :

• 4 flashes = «The washing machine does not start», follow the corresponding sugges-

tions in «Possible cause/Solutions» box and restart the programme.

• 1 flash = «The machine does not fill», follow the corresponding suggestions in «Possi-

ble cause/Solutions» box and restart the programme.

What to do if… 21

• 2 flashes = «The machine does not empty and/or does not spin», follow the corre-

sponding suggestions in «Possible cause/Solutions» box and restart the programme.
Once the problem has been eliminated, press the button 5 to restart the programme. If af­ter all checks, the problem persists, contact your local Service Centre.

Problem Possible cause/Solution

The door has not been closed. (Yellow pilot

light of button 5 blinks)

• Close firmly the door.
The plug is not properly inserted in the power
socket.

• Insert the plug into the power socket.
There is no power at the socket.

• Please check your domestic electrical installa-

The washing machine does not start:

The machine does not fill:

The machine fills then empties immediately:

tion.

The main fuse has blown.

•Replace the fuse.
The selector dial is not correctly positioned and
the button 5 has not been pressed.

• Please turn the selector dial and press the
button 5 again.

The delay start has been selected.

• If the laundry are to be washed immediately,
cancel the delay start.

The water tap is closed. (Yellow pilot light of

button 5 blinks)

• Open the water tap.

The inlet hose is squashed or kinked. (Yellow pi-

lot light of button 5 blinks)

• Check the inlet hose connection.

The filter in the inlet hose or the inlet valve filter
are blocked. (Yellow pilot light of button 5

blinks)

• Clean the water inlet filters (see "Cleaning the
water inlet filters" for more details)

The door is not properly closed. (Yellow pilot

light of button 5 blinks)

• Close firmly the door.

The end of the drain hose is too low.

• Refer to relevant paragraph in «water drain­age» section.

22 What to do if…

Problem Possible cause/Solution

The machine does not empty and/or does
not spin:

There is water on the floor:

Unsatisfactory washing results:

The drain hose is squashed or kinked. (Yellow
pilot light of button 5 blinks)

• Check the drain hose connection.

The drain filter is clogged. (Yellow pilot light

of button 5 blinks)

• Clean the drain filter.

An option or a programme that ends with the
water still in the tub or a that eliminates all the
spinning phases has been selected.

• Select the draining or spinning programme.

The laundry is not evenly distributed in the
drum.

• Redistribute the laundry.

• The laundry load is perhaps to little, add more
items, redistribute the load manually and
then select the spinning programme.

Too much detergent or unsuitable detergent
(creates too much foam) has been used.

• Reduce the detergent quantity or use another
one.

Check whether there are any leaks from one of
the inlet hose fittings. It is not always easy to
see this as the water runs down the hose; check
to see if it is damp.

• Check the water inlet hose connection.

The drain or the inlet hose is damaged.

• Replace it with a new one.

The cap on the emergency emptying hose has
not been replaced or the filter has not been
properly screwed in after cleaning action.

• Refit the cap on the emergency emptying
hose or screw the filter fully in.

Too little detergent or unsuitable detergent has
been used.

• Increase the detergent quantity or use anoth­er one.

Stubborn stains have not been treated prior to
washing.

• Use commercial products to treat the stub­born stains.

The correct temperature was not selected.

• Check if you have selected the correct tem­perature.

Excessive laundry load.

• Introduce into the drum less laundry.

Problem Possible cause/Solution

The programme is still running.

• Wait the end of washing cycle.

The door will not open:

The machine vibrates is noisy:

The machine makes an unusual noise:

No water is visible in the drum:

The door lock has not been released.

• Wait a few minutes.

There is water in the drum.

• Select drain or spin programme to empty out

The transit bolts and packing have not been re­moved.

• Check the correct installation of the appli-

The support feet have not been adjusted.

• Check the correct levelling of the appliance.

The laundry is not evenly distributed in the
drum.

• Redistribute the laundry.

Maybe there is very little laundry in the drum.

• Load more laundry.

The machine is fitted with a type of motor
which makes an unusual noise compared with
other traditional motors. This new motor en­sures a softer start and more even distribution
of the laundry in the drum when spinning, as
well as increased stability of the machine.

Machines based on modern technology operate
very economically using very little water with­out affecting performance.

If you are unable to identify or solve the problem,
contact our service centre. Before telephoning,
make a note of the model, serial number and pur­chase date of your machine: the Service Centre
will require this information.

What to do if… 23

the water.

ance.

24 Technical data

TECHNICAL DATA

Dimensions Width

Electrical connection
Voltage - Overall power - Fuse

Water supply pressure Minimum

Maximum Load Cotton 6 kg

Spin Speed Maximum 1000 rpm

Height
Depth
Depth (Overall dimensions)

Information on the electrical connection is given on the rating
plate, on the inner edge of the appliance door.

Maximum

60 cm
85 cm
60 cm
63 cm

0,05 MPa
0,8 MPa

CONSUMPTION VALUES

Programme Energy consumption

White Cottons 95 °C 2.0 61 135

Cottons 60 °C 1.3 58 125

Cottons 40 °C 0.7 58 120

Synthetics 40 °C 0.5 50 80

Delicates 40 °C 0.55 60 65

Wool/ Handwash 30 °C 0.25 53 55

1) The consumption information shown in this chart is indicative. It can vary depending on the quantity and the
type of laundry, on the temperature of the water supply and on the ambient temperature.

(KWh)

1)

Standard programmes for the Energy Label consumption values

The cotton 60 °C economy and cotton 40 °C economy are the standard cotton programmes
for normally soiled cotton laundry. They are suitable to clean normally soiled cotton laundry
and they are the most efficient programmes in terms of combined energy and water con­sumption for washing that type of cotton laundry.
They agree with EN60456.

The actual water temperature may differ from the declared cycle temperature.

Water consump-

tion (litre)

1)

Programme dura-

tion (Minutes)

1)

INSTALLATION INSTRUCTIONS

INSTALLATION

Unpacking

All transit bolts and packing must be removed before using the appliance.

Installation 25

You are advised to keep all transit devices so that they can be refitted if the machine ever
has to be transported again.

1. After removing all the packaging, care-

fully lay machine on it’s back to remove
the polystyrene base from the bottom.

2. Remove the power supply cable and the

draining and inlet hose from the hose
holders on the rear of the appliance.

3. Unscrew the three bolts with the key

supplied with the appliance.

26 Installation

4. Slide out the relevant plastic spacers.

5. Open the porthole and remove the poly-

styrene block fitted on the door seal.

6. Fill the smaller upper hole and the two

large ones with the corresponding plas­tic plug caps supplied in the bag con­taining the instruction booklet.

Installation 27

Positioning and levelling

Install the machine on a flat hard floor.
Make sure that air circulation around the machine
is not impeded by carpets, rugs etc.
Before placing it on small tiles, apply a rubber
coating.
Never try to correct any unevenness in the floor
by putting pieces of wood, cardboard or similar
materials under the machine.
If it is impossible to avoid positioning the machine
next to a gas cooker or coalburning stove, an in­sulating panel covered with aluminium foil on the
side facing the cooker or stove, must be inserted
between the two appliances.
The machine must not be installed in rooms where the temperature can drop below 0°C.
The water inlet hose and the drain hose must not be kinked.
Please ensure that when the appliance is installed, it is easily accessible for the engineer in
the event of a breakdown.
Carefully level by screwing the adjustable feet in or out. Never place cardboard, wood or
similar materials under the machine to compensate for any unevenness in the floor.

Rubber feet kit (4055126249)

Available from your authorized dealer.
The rubber feet are particularly recommended on floating, slippery and wooden floors.
Mount the rubber feet to prevent vibration, noises and displacement of the appliance dur­ing operation.
Read carefully the instructions supplied with the kit.

Water inlet

This appliance must be connected to a cold water supply.

1. Connect the hose to a tap with a 3/4”

thread. Always use the hose supplied
with the appliance.

Do not use the hose from your previ­ous machine to connect to the water
supply.

28 Installation

2. The other end of the inlet hose which

connects to the machine can be turned
as showed in the picture.

Do not place the inlet hose down­wards. Angle the hose to the left or
right depending on the position of
your water tap.

3. Set the hose correctly by loosening the

ring nut. After positioning the inlet
hose, be sure to tighten the ring nut

again to prevent leaks.
The inlet hose must not be lengthened. If it is too short and you do not wish to move the
tap, you will have to purchase a new, longer hose specially designed for this type of use.
Installation should comply with local water authority and building regulations require­ments. A minimum water pressure of 0.05 MPa is required for safe operation of the appli­ance.

Before connecting up the machine to new pipework or to pipework that has not been used
for some time, run off a reasonable amount of water to flush out any debris that may have
collected in the pipes.

Water drainage

The end of the drain hose can be positioned in three ways:

Hooked over the edge of a sink using the plastic hose guide supplied with the

1.

machine.

In this case, make sure the end cannot come unhooked when the machine is emptying.

This could be done by tying it to the tap

with a piece of string or attaching it to

the wall.

2. In a sink drain pipe branch. This

branch must be above the trap so that

the bend is at least 60 cm above the

ground.

Directly into a drain pipe at a height

3.

of not less than 60 cm and not more

than 90 cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the
drain pipe must be larger than the outside
diameter of the drain hose.
The drain hose must not be kinked.

Electrical connection

The drain hose may be extended to a maximum of 4 metres. An additional drain hose and
joining piece is available from your local Service Centre.

ELECTRICAL CONNECTION

Information on the electrical connection is given on the rating plate on the inner edge of
the appliance door.
Check that your domestic electrical installation can take the maximum load required, also
taking into account any other appliances in use.

WARNING!
Connect the machine to an earthed socket.

29

WARNING!
The manufacturer does not accept any responsibility for damage or injury through
failure to comply with the above safety precaution.

WARNING!
The power supply cable must be easily accessible after installing the machine.

WARNING!
Should the appliance power supply cable need to be replaced, this must be carried
out by a Service Centre.

ENVIRONMENT CONCERNS

The symbol on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it should be taken to the appropriate collection point
for the recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of this product,
please contact your local council, your household waste disposal service or the shop where
you purchased the product.

30

Packaging materials

The materials marked with the symbol are recyclable.
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by disposing of them properly in appropriate collec­tion containers.

Ecological hints

To save water, energy and to help protect the environment, we recommend that you follow
these tips:

• Normally soiled laundry may be washed without prewashing in order to save detergent,

water and time (the environment is protected too!).

• The machine works more economically if it is fully loaded.

• With adequate pre-treatment, stains and limited soiling can be removed; the laundry can

then be washed at a lower temperature.

• Measure out detergent according to the water hardness, the degree of soiling and the

quantity of laundry being washed.

31

www.aeg.com/shop

132933250-A-242011