AEG GA60GXI200 User Manual

user manual

GA60GXI200

dishwasher

We were thinking of you

when we made this product

welcome to the world of Electrolux electrolux 3

You’ve chosen a first class product from Electrolux, which
hopefully will provide you with lots of pleasure in the future.
Electrolux ambition is to offer a wide variety of quality products
that make your life more comfortable. You can look at some
examples on the cover in this manual. But now it’s time to study
this manual and start using and enjoying the benefits from your
new machine. We promise that it’ll make your life a little easier.
Good luck!

Welcome to the world of Electrolux

117990 83/0

Safety information 5
Product description 7
Control panel 8
First use 10
Daily use 14
Washing programmes 26
Care and cleaning 27
Something not working 29
Technical data 32
Hints for test institutes 34
Installation 35
Environment concerns 40
Warranty/Point of service 41

Contents

The following symbols are used in this manual:

Important information concerning your personal safety and information on
how to avoid damaging the appliance.

General information and tips

Environmental information

4 electrolux contents

safety information electrolux 5

In the interest of your safety and to
ensure the correct use, before
installing and first using the
appliance, read this user manual
carefully, including its hints and
warnings. To avoid unnecessary
mistakes and accidents, it is
important to ensure that all people
using the appliance are thoroughly
familiar with its operation and
safety features. Save these
instructions and make sure that
they remain with the appliance if it
is moved or sold, so that everyone
using it through its life will be
properly informed on appliance use
and safety.

Correct use

● This dishwasher is only intended

for washing household utensils
suitable for machine washing.

● Do not put any solvents in the

dishwasher. This could cause an
explosion.

● Knives and other items with sharp

points must be loaded in the
cutlery basket with their points
down or placed in a horizontal
position in the upper basket.

● Only use products (detergent, salt

and rinse aid) suitable for
dishwashers.

● Avoid opening the door whilst the

appliance is in operation, hot
steam may escape.

● Do not take any dishes out of the

dishwasher before the end of the
dishwashing cycle.

Safety information

● After use, isolate the appliance

from the power supply and turn off
the water supply.

● This product should be serviced

only by an authorised service
engineer, and only genuine spare
parts should be used.

● Under no circumstances should

you attempt to repair the machine
yourself. Repairs carried out by
inexperienced persons will cause
injury or serious malfunctioning.
Contact your local Service Force
Centre. Always insist on genuine
spare parts.

General safety

● Dishwasher detergents can cause

chemical burns to eyes, mouth and
throat. Could endanger life!
Comply with the safety instructions
of the dishwasher detergent
manufacturer.

● The water in your dishwasher is

not for drinking. Detergent
residues may still be present in
your machine.

● Ensure that the door of the

dishwasher is always closed when
it is not being loaded or unloaded.
In this way you will avoid anybody
tripping over the open door and
hurting themselves.

● Do not sit or stand on the open

door.

Child safety

● This appliance is designed to be

operated by adults. Don’t allow
children to use the dishwasher
unsupervised.

6 electrolux safety information

Installation

● Check your dishwasher for any

transport damage. Never connect
a damaged machine. If your
dishwasher is damaged contact
your supplier.

● All packaging must be removed

before use.

● Any electrical and plumbing work

required to install this appliance
must be carried out by a qualified
and competent person.

● For safety reasons it is dangerous

to alter the specifications or
attempt to modify this product in
any way.

● Never use the dishwasher if the

electrical supply cable and water
hoses are damaged; or if the
control panel, work top or plinth
area are damaged such that the
inside of the appliance is freely
accessible. Contact your local
Service Force centre, in order to
avoid hazard.

● All sides of the dishwasher must

never be drilled to prevent damage
to hydraulic and electric
components.

For electrical and water connection
carefully follow the instructions
given in specific paragraphs.

● Keep all packaging well away from

children. There is risk of
suffocation.

● Keep all detergents in a safe place

out of children’s reach.

● Keep children well away from the

dishwasher when the door is open.

product description electrolux 7

Product description

Upper basket
Water hardness dial
Salt container
Detergent dispenser
Rinse aid dispenser
Rating plate
Filters
Lower spray arm
Upper spray arm

1

2

3

4

5

6

7

8

9

8 electrolux control panel

Control panel

The digital display indicates:

- the level of hardness to which the
water softener is set,

- the approximate remaining time of
the running programme,

- activation/deactivation of the rinse
aid dispenser (ONLY with

"Multi-

tab function active"),

- the end of a washing programme
(a zero will appear in the digital
display),

- the countdown of the delay start,

- fault codes concerning malfunction
of the dishwasher.

Programme selection buttons

Multi-tab button

Delay start button

Digital display

Indicator lights

On/Off button

1

2

3

4

5

6

control panel electrolux 9

Programme in progress

Indicator lights

Illuminates when a washing programme is set
and remains illuminated for all the duration of
the washing programme.

Salt

Illuminates when the special salt has run out.

Rinse aid

Illuminates when the rinse aid has run out.

The salt and rinse aid indicator
lights are never illuminated while a
washing programme is running
even if filling with salt and/or rinse
aid is necessary.

To cancel a set programme or a
programme in progress

Simultaneously press and hold the
two Cancel buttons, until all the
programme button lights will
illuminate. The programme has been
cancelled and the machine is now in
setting mode.

Setting mode

● Press On/Off button, ALL

programme button lights are
illuminated = appliance in setting
mode.

● Press On/Off button, ONLY a

programme button light is
illuminated = last performed or
selected programme still set.
In this case, to return to setting
mode, the programme has to be
cancelled.

Always remember that when:

- setting a washing programme,

- setting the water softener,

- activating/deactivating the rinse aid
dispenser,

the appliance MUST be in setting
mode.

10 electrolux first use

Before using your dishwasher for the
first time:

● Ensure that the electrical and

water connections comply with the
installation instructions

● Remove all packaging from inside

the appliance

● Set the water softener

● Pour 1 litre of water inside the salt

container and then fill with
dishwasher salt

● Fill the rinse aid dispenser

If you want to use combi detergent
tablets such as: "3 in 1", "4 in 1",
"5 in 1" etc... set the Multi-tab
function (see "Multi-tab function").

First use

Set the water softener

The dishwasher is equipped with a
water softener designed to remove
minerals and salts from the water
supply, which would have a
detrimental or adverse effect on the
operation of the appliance.

The higher the content of these
minerals and salts, the harder your
water is.

Water hardness is measured in
equivalent scales, German degrees
(°dH), French degrees (°TH) and
mmol/l (millimol per litre - international
unit for the hardness of water).

The softener should be adjusted
according to the hardness of the
water in your area. Your local Water
Authority can advise you on the
hardness of the water in your area.

*

no salt is necessary

Water hardness

°dH °TH mmol/l manually electronically

Adjusting the water

hardness setting

Use of

salt

51 - 70 91 - 125 9.0 - 12.5 2 level 10 yes
43 - 50 76 - 90 7.6 - 8.9 2 level 9 yes

37 - 42 65 - 75 6.5 - 7.5 2 level 8 yes
29 - 36 51 - 64 5.1 - 6.4 2 level 7 yes

23 - 28 40 - 50 4.0 - 5.0 2 level 6 yes
19 - 22 33 - 39 3.3 - 3.9 2 level 5 yes

15 - 18 26 - 32 2.6 - 3.2 1 level 4 yes
11 - 14 19 - 25 1.9 - 2.5 1 level 3 yes

4 - 10 7 - 18 0.7 - 1.8 1 level 2 yes

< 4 < 7 < 0.7 1 level 1 no

*

first use electrolux 11

The water softener must be set in
both ways: manually, using the water
hardness dial and electronically, using
some of the programme buttons on
the control panel

Setting manually
The dishwasher is factory set at

position 2.

1. Open the dishwasher door.

2. Remove the lower basket from the
dishwasher.

3. Turn the water hardness dial to
position 1 or 2 (see table).

4. Replace the lower basket.

Setting electronically
The dishwasher is factory set at

level 5.

1. Press the On/Off button. The
dishwasher must be in setting
mode.

2. Simultaneously press and hold
buttons 2 and 3, until the lights of
buttons 1, 2 and 3 start flashing.

3. Press button 1, the lights of
buttons 2 and 3 turn off while the
light of button 1 goes on flashing.
In the digital display is visible the
current level.

Examples:

displayed = level 5
displayed = level 10

4. To change the level, press button

1. Each time the button is pressed
the level changes. (For the
selection of the new level see the
chart).

Examples:

if the current level is 5, by pressing
button 1 once, level 6 is selected.

if the current level is 10, by
pressing button 1 once, level 1 is
selected.

5. To memorise the operation, switch
off the dishwasher by pressing the
On/Off button.

12 electrolux first use

Filling with dishwasher salt

Only use salt specifically designed for
use in dishwashers.
All other types of salt not specifically
designed for use in a dishwasher,
especially table salt, will damage the
water softener.
Only fill with salt just before starting
one of the complete washing
programmes.
This will prevent any grains of salt or
salty water, which may have been
spilt, remaining on the bottom of the
machine for any period of time, which
may cause corrosion.

To fill:

1. Open the door, remove the lower
basket and unscrew the cap of the
salt container by turning it
anticlockwise.

2. Pour 1 litre of water inside the
container (this is necessary only

before filling with salt for the
first time).

3. Using the funnel provided, pour in
the salt until the container is full.

4. Replace the cap making sure that
there is no trace of salt on the
screw thread or on the gasket.

5. Replace the cap tightly turning it
clockwise until it stops with a click.

Do not worry if water overflows from
the unit when filling with salt, this is
quite normal.

The salt indicator light on the
control panel can remain
illuminated for 2-6 hours after the
salt has been replenished,
assuming the dishwasher remains
switched on. If you are using salts
that take longer to dissolve then
this can take longer. The function
of the machine is not affected.

first use electrolux 13

Filling with rinse aid

Rinse aid ensures thorough rinsing,
and spot and streak free drying.

Rinse aid is automatically added
during the last rinse.

1. Open the container by pressing
the release button (A).

2. Add the rinse aid in the container.
The maximum level for filling is
indicated by "max".

The dispenser holds about 110 ml of
rinse aid, which is sufficient for
between 16 and 40 dishwashing
cycles, depending upon the dosage
setting.

According to the finish and drying
results obtained, adjust the dose of
rinse aid by means of the 6 position
selector (position 1 minimum dosage,
position 6 maximum dosage).

The dose is factory set in position 4.
Increase the dose if there are drops of

water or lime spots on the dishes after
washing.

Reduce it if there are sticky whitish
streaks on the dishes or a bluish film
on glassware or knife blades.

3. Ensure that the lid is closed after
every refill.

Clean up any rinse aid spilt during
filling with an absorbent cloth to
avoid excess foaming during the
next wash.

Only use branded rinse aid for
dishwashers.

Never fill the rinse aid dispenser
with any other substances (e.g.
dishwasher cleaning agent, liquid
detergent). This would damage the
appliance.

● Check if it’s necessary to refill with

dishwasher salt or rinse aid

● Load cutlery and dishes into the

dishwasher.

● Fill with dishwasher detergent .

● Select a wash programme suitable

for the cutlery and dishes.

● Start the wash programme.

Loading cutlery and dishes

Sponges, household cloths and any
object that can absorb water may not
be washed in the dishwasher.

● Before loading the dishes, you

should:

- Remove all left over food and
debris.

- Soften remnants of burnt food in
pans

● When loading the dishes and

cutlery, please note:

- Dishes and cutlery must not
impede the rotation of the spray
arms .

- Load hollow items such as cups,
glasses, pans, etc. with the
opening downwards so that water
cannot collect in the container or
a deep base.

- Dishes and items of cutlery must
not lie inside one another, or
cover each other.

- To avoid damage to glasses, they
must not touch.

Daily use

- Lay small objects in the cutlery
basket.

● Plastic items and pans with non

stick coatings have a tendency to
retain water drops; these items will
not dry as well as porcelain and
steel items.

● Light items (plastic bowls etc.)

must be loaded in the upper
basket and arranged so they do
not move.

14 electrolux daily use

daily use electrolux 15

For washing in the dishwasher the following cutlery and dishes

are not suitable: - Cutlery with wooden, horn, china or

mother-of-pearls handles.

- Plastic items that are not heat resistant.

- Older cutlery with glued parts that are not
temperature resistant.

- Bonded cutlery items or dishes.

- Pewter or copper items.

- Lead crystal glass.

- Steel items prone to rusting.

- Wooden platters.

- Items made from synthetics fibres.

are of limited suitability:

- Only wash stoneware in the dishwasher if
it is specially marked as being
dishwasher-safe by the manufacturer.

- Glazed patterns may fade if machine
washed frequently.

- Silver and aluminium parts have a
tendency to discolour during washing:
Residues, e.g. egg white, egg yolk and
mustard often cause discolouring and
staining on silver. Therefore always clean
left-overs from silver immediately, if it is
not to be washed straight after use.

16 electrolux daily use

Open the door and slide out the
baskets to load the dishes.

The lower basket

The lower basket is designed to take
saucepans, lids, plates, salad bowls,
cutlery etc.

Serving dishes and large lids should
be arranged around the edge of the
basket, ensuring that the spray arms
can turn freely.

The two rows of prongs on the lower
basket can be easily lowered to allow
you to load pots, pans and bowls.

daily use electrolux 17

To make loading of the cutlery basket
easier, lower the cutlery basket
handle (fig.2).

For best results we recommend you
to use the cutlery grids.

If the size and dimensions of the cutlery
do not allow the use of the grids, they
can be easily hidden (fig. 3).

The cutlery basket

Long bladed knives stored in an
upright position are a potential
hazard.

Long and/or sharp items of cutlery
such as carving knives must be
positioned horizontally in the upper
basket.

Take care when loading or
unloading sharp items such as
knives.

Forks and spoons should be placed in
the removable cutlery basket with the
handles facing downwards and the
knives with their handles facing
upwards (fig.1).

If the handles protrude from the
bottom of the basket, obstructing the
lower spray arm, load the cutlery with
the handles facing upwards.

Mix spoons with other cutlery to
prevent them from sticking together.

fig. 1

fig. 2

fig. 3

18 electrolux daily use

The cutlery basket is in two parts
which can be separated to give
greater loading flexibility. To separate
the two parts, slide them horizontally
in opposite directions and pull them
apart (fig. 4).

To reassemble, reverse the
procedure.

fig. 4

daily use electrolux 19

The central rows of prongs can be
easily lowered to improve loading
flexibility.

The upper basket

The upper basket is designed for
saucers, salad bowls, cups, glasses,
pots and lids.

Arrange items on and underneath the
cup racks so that water can reach all
surfaces.

Glasses with long stems can be
placed upside down in the cup racks.

The cup racks can be adjusted in
three different positions to improve
loading flexibility.

Before closing the door, ensure that
the spray arms can rotate freely.

For glasses with long stems
(according to the size and
dimensions), set the glass holder to
the left or right position.

20 electrolux daily use

Adjusting the height of the upper basket

If washing very large plates you can load them in the lower basket after moving
the upper basket to the higher position.

To move to the higher position
proceed as follows:

1. Pull out the basket until it stops.

2. Carefully lift both sides upwards
until the mechanism is engaged
and the basket is stable.

To lower the basket to the original
position proceed as follows:

1. Pull out the basket until it stops.

2. Carefully lift both sides upwards
and then allow the mechanism to
drop back down slowly, keeping
hold of it.

Never lift or lower the basket on
one side only

With the upper basket raised we
recommend to adjust the cup racks
in the lowest position.

After loading your machine always
close the door, as an open door can
be a hazard.

Maximum height of the dishes in the lower basket

33 cm

With upper basket raised

29 cm

With upper basket lowered

daily use electrolux 21

Use of detergent

Only use detergents specifically
designed for use in dishwashers.

Please observe the manufacturer’s
dosing and storage recommendations
as stated on the detergent packaging.

Using no more than the correct
amount of detergent contributes to
reducing pollution.

Fill with detergent

1. Open the lid.

2. Fill the detergent dispenser (1)
with detergent. The marking
indicates the dosing levels:

20 = approximately 20 g of
detergent

30 = approximately 30 g of
detergent

3. All programmes with prewash
need an additional detergent dose
(5/10 g) that must be placed in the
prewash detergent chamber (2).
This detergent will take effect
during the prewash phase.

When using detergent tablets;
place the tablet in compartment (1)

4. Close the lid and press until it
locks in place.

Detergent tablets

Detergent tablets from different
manufactures dissolve at different
rates. For this reason, some detergent
tablets do not attain their full cleaning
power during short washing
programmes. Therefore, please use
long washing programmes when
using detergent tablets, to ensure the
complete removal of detergent
residuals.

1

2

22 electrolux daily use

Multi-tab function

This appliance is equipped with the
Multi-tab function, that allows the use
of combi detergent tablets.

These products are detergents with a
combined cleaning, rinsing and salt
functions. They can also contain other
different agents depending on which
kind of tablets you choose (‘3 in 1’, ‘4
in 1’, ‘5 in 1’ etc...)

Check whether these detergents are
suitable for your water hardness. See
the manufacturers instructions.

Once this function is selected it will
remain active also for the following
washing programmes.

With the selection of this function the
inflow of rinse aid and salt from each
respective supply container is
automatically deactivated and also the
indicator lights for salt and rinse aid
are deactivated.

Select the Multi-tab function before
the start of a washing programme.

With the use of the Multi-tab function,
the cycle durations may change. In
this case, in the digital display, the
indication of the running time of the
programme is automatically updated.

Once the programme is running, the
Multi-tab function can NO longer be
changed. If you want to exclude the
Multi-tab function you have to cancel
the programme setting and then
deactivate the Multi-tab function.
In this case you have to set a
washing programme (and desired
options) again.

Activation / deactivation of the
Multi-tab function

Press the Multi-tab button, the
corresponding indicator light
illuminates. (Function active).

To deactivate the function press the
Multi-tab button again, the
corresponding indicator light turns off.
(Function not active).

If the drying results are not
satisfactory we suggest that you:

1. Fill up the rinse aid dispenser with
rinse aid.

2. Activate the rinse aid dispenser.

3. Set the rinse aid dosage to
position 2.

● The activation/deactivation of the

rinse aid dispenser can only be
possible with the Multi-tab function
active.

Activation/deactivation of the rinse
aid dispenser

1. Press the On/Off button. The
dishwasher must be in setting
mode.

2. Simultaneously press and hold
buttons 2 and 3, until the lights of
buttons 1, 2

, and 3 start flashing.

daily use electrolux 23

3. Press button 2, the lights of
buttons 1 and 3 turn off while the
light of button 2 goes on flashing.
The digital display indicates the
current setting.

4. To change the setting, press
button 2 again, the digital display
indicates the new setting.

5. To memorise the operation, switch
off the dishwasher by pressing the
On/Off button.

Rinse aid dispenser deactivated

Rinse aid dispenser activated

If you decide to turn back to the
use of standard detergent system
we advise that you:

1. Deactivate the Multi-tab function.

2. Fill up the salt container and the
rinse aid dispenser again.

3. Adjust the water hardness setting
to the highest setting and perform
1 normal washing programme
without loading any dishes.

4. Adjust the water hardness setting
according to the hardness of the
water in your area.

5. Adjust the rinse aid dosage.

24 electrolux daily use

Select and start a washing
programme

Select the washing programme and
delay start with the door slightly
opened. The start of the
programme or the countdown of
the delay start will occur only after
the closure of the door. Until then it
is possible to modify the settings.

1. Check that the baskets have been
loaded correctly and that the spray
arms are free to rotate

2. Check that the water tap is opened

3. Press the On/Off button. The
dishwasher must be in setting
mode.

4. Press the button corresponding to
the required programme (see
"Washing programmes" chart).

When a programme has been
selected the corresponding light
will illuminate.

The programme in progress
indicator light illuminates.

Close the dishwasher door, the
programme starts automatically.

The programme in progress
indicator light remains illuminated.

Setting and starting the programme
with "delay start"

1. After having selected the washing
programme, press the delay start
button until the flashing number of
hours for the delay start will
appear in the digital display. The
commencement of the selected
washing programme can be
delayed from 1 to 19 hours.

2. Close the dishwasher door, the
countdown starts automatically.
The number in the display is no
longer flashing but fixed with static
light.

3. The countdown will decrease with
steps of 1 hour.

4. The opening of the door will
interrupt the countdown. Close the
door; the countdown will continue
from the point at which it was
interrupted.

5. Once the delay start has elapsed
the programme will start
automatically.

With the delay start function set,
the programme in progress
indicator light is off. Once the
countdown of the delay start has
elapsed, the washing programme
will start automatically and the
programme in progress indicator
light will illuminate.

The selection of the washing
programme and delay start can
also occur with the door closed.
Keep in mind that in this way, once
a washing programme button is
pressed you have ONLY 3
seconds in which you can choose
another programme or select a
delay start, after which the
selected programme will start
automatically.

daily use electrolux 25

Cancelling the "delay start"

To cancel a delay start in progress
you have to reset the dishwasher.

Simultaneously press and hold the
two Cancel buttons, until all the
programme button lights illuminate.

Cancelling a delay start involves
also the cancelling of the washing
programme set. In this case you
have to set the washing
programme again.

Interrupt or cancel a washing
programme in progress ONLY if it’s
absolutely necessary.
Attention! Hot steam may escape
when the door is opened. Open the
door carefully.

Interrupt a washing programme in
progress:

● Open the dishwasher door; the

programme will stop. Close the
door; the programme will start from
the point at which it was
interrupted.

● Press the On/Off button, all lights

will turn off. Press the On/Off
button again; the programme will
start from the point at which it was
interrupted.

End of the washing programme

● The dishwasher will automatically

stop.

● The programme in progress

indicator light remains illuminated.

● The light of the programme just

ended will remain on.

● Zero appears in the digital display.

1. Switch off the dishwasher by
pressing the On/Off button.

2. Open the dishwasher door, leave it
ajar and wait a few minutes before
removing the dishes; in this way
they will be cooler and the drying
will be improved.

Cancel a washing programme in
progress

● Simultaneously press and hold the

two Cancel buttons, until all the
programme button lights illuminate.
The washing programme has been
cancelled.

If a new washing programme is to
be selected, check that there is
detergent in the detergent
dispenser.

Unloading the dishwasher

● Hot dishes are sensitive to knocks.

The dishes should therefore be
allowed to cool down before
removing from the appliance.

● Empty the lower basket first and

then the upper one; this will avoid
water dripping from the upper
basket onto the dishes in the lower
one.

● Water may appear on the sides

and the door of the dishwasher as
the stainless steel will eventually
become cooler than the dishes.

When the washing programme has
finished, it is recommended that
the dishwasher is unplugged and
the water tap turned off.

26 electrolux washing programmes

Washing programmes

Washing programmes information

(1)During the "Auto" washing

programme the amount of soil on
the dishes is determined by how
cloudy the water is.
The programme duration, water
and energy consumption levels
can vary; this depends upon if the
appliance is fully or partially loaded
and if the dishes are lightly or
heavily soiled. The temperature of
the water is automatically adjusted
between 50°C and 65°C.

(2)Ideal for washing a partially loaded

dishwasher. This is the perfect
daily programme, made to meet
the needs of a family of 4 persons
who only wish to load breakfast
and dinner crockery and cutlery.

(3)Test programme for test institutes.

Programme

Intensive

Heavy soil

Crockery,
cutlery, pots
and pans

Prewash
Main wash up to 70°C
2 intermediate rinses
Final rinse
Drying

Normal soil

Auto (1)

Crockery,
cutlery, pots
and pans

Prewash
Main wash up to 50°C or 65°C
1 or 2 intermediate rinses
Final rinse
Drying

Degree of

soil

Type of load Programme description

Normal soil

Eco (2)

Crockery and
cutlery

Prewash
Main wash up to 50°C
1 intermediate rinse
Final rinse
Drying

Quick (3)

Normal or

light soil

Crockery and
cutlery

Main wash up to 60°C
Final rinse

care and cleaning electrolux 27

Cleaning the filters

The filters must be checked and
cleaned from time to time. Dirty filters
will degrade the washing result.

1. Open the door, remove the lower
basket.

2. The dishwasher filter system
comprises a coarse filter (A), a
microfilter (B) and a flat filter.
Unlock the filter system using the
handle on the microfilter.

3. Turn the handle about

1

/4a turn
anticlockwise and remove the filter
system.

Before cleaning the filters ensure
that the machine is switched off.

4. Take hold of the coarse filter (A)
by the handle with the hole and
remove from the microfilter (B).

5. Clean all filters thoroughly under
running water.

6. Remove the flat filter from the
base of the washing compartment
and clean both faces thoroughly.

7. Put the flat filter back in the base
of the washing compartment and
ensure that it fits perfectly.

8. Place the coarse filter (A) in the
microfilter (B) and press together.

9. Put the filter combination in place
and lock by turning the handle
clockwise to the stop. During this
process ensure that the flat filter
does not protrude above the base
of the washing compartment.

Care and cleaning

NEVER use the dishwasher without
filters. Incorrect repositioning and
fitting of the filters will produce poor
washing results and may result in
damage to the appliance.

28 electrolux care and cleaning

NEVER try to remove the spray
arms.

If residues of soil have clogged the
holes in the spray arms, remove them
with a cocktail stick.

Frost precautions

Avoid placing the machine in a
location where the temperature is
below 0°C. If this is unavoidable,
empty the machine, close the
appliance door, disconnect the water
inlet pipe and empty it.

Moving the machine

If you have to move the machine

(moving house etc....):

1. Unplug it.

2. Turn the water tap off.

3. Remove the water inlet and
discharge hoses.

4. Pull the machine out together with
the hoses.

Avoid over tilting the machine during
transportation.

External cleaning

Clean the external surfaces of the
machine and control panel with a
damp soft cloth. If necessary use only
neutral detergents. Never use
abrasive products, scouring pads or
solvent (acetone, trichloroethylene

etc....).

Ensure that the seals around the
door, the detergent and rinse aid
dispensers are cleaned regularly with
a damp cloth.

Internal cleaning

We recommend every 3 months to
run the wash programme for heavy
soiled dishes using detergent but
without dishes.

Prolonged periods of non­operation

If you are not using the machine for
any prolonged period of time you are
advised to:

1. Unplug the appliance and then
turn off the water.

2. Leave the door ajar to prevent the
formation of any unpleasant
smells.

3. Leave the inside of the machine
clean.

something not working electrolux 29

The dishwasher will not start or stops during operation.
Certain problems are due to the lack of simple maintenance or oversights,
which can be solved with the help of the indications described in the chart,
without calling out an engineer.

Switch off the appliance and carry out the following suggested corrective
actions.

Something not working

Fault code and malfunction Possible cause and solution

● appears in the digital display

The dishwasher does not fill with water

● The water tap is blocked or furred with

limescale.
Clean the water tap.

● The water inlet hose has not been

correctly laid or it is bent or squashed.
Check the water drain hose connection.

● The filter (where present) in the threaded

hose fitting at the water inlet valve is
blocked.
Clean the filter in the threaded hose.

● The water tap is turned off.

Turn the water tap on.

● appears in the digital display

The dishwasher will not drain

● The sink spigot is blocked.

Clean out the sink spigot.

● The water drain hose has not been

correctly laid or it is bent or squashed.
Check the water drain hose connection.

● appears in the digital display

Anti-flood device is activated

● Close the water tap and contact your

local Service Force Centre.

30 electrolux something not working

Malfunction Possible cause and solution

The programme does not start

● The dishwasher’s door has not been

properly closed.
Close the door.

● The main plug is not plugged in.

Insert the main plug.

● Delay start has been set.

If dishes are to be washed immediately,
cancel the delay start.

● The fuse has blown out in the household

fuse box.
Replace the fuse.

Once these checks have been carried
out; switch on the appliance.

The programme will continue from the
point at which it was interrupted.

If the message reappears in the
display contact the Service Force
Centre.

For other messages not described in
the chart, please contact your Service
Force Centre.

Contact your local Service Force
Centre, quoting the model (Mod.),
product number (PNC) and serial
number (S.N.).
This information can be found on the
rating plate located on the side of the
dishwasher door.

So that you always have these
numbers at hand, we recommend you
to make a note of them here:

Mod. : . . . . . . . . . . . . . . . . . . . . . . .

PNC :. . . . . . . . . . . . . . . . . . . . . . . .

S.N. :. . . . . . . . . . . . . . . . . . . . . . . .

something not working electrolux 31

If after all these checks, the problem
persists, contact your local Service
Force Centre.

The wash results are not satisfactory

The dishes are not
clean

●The wrong washing programme has been selected.

●The dishes are arranged in such a way as to stop water

reaching all parts of the surface. The baskets must not
be overloaded.

●The spray arms do not rotate freely due to incorrect

arrangement of the load.

●The filters in the base of the washing compartment are

dirty or incorrectly positioned.

●Too little or no detergent has been used.

●Where there are limescales deposits on the dishes; the

salt container is empty or the incorrect level of the water
softener has been set.

●The drain hose connection is not correct.

●The salt container cap is not properly closed.

The dishes are wet and
dull

●Rinse aid was not used.

●The rinse aid dispenser is empty.

There are streaks, milky
spots or a bluish
coating on glasses and
dishes

●Decrease rinse aid dosing.

Water drops have dries
onto glasses and dishes

●Increase rinse aid dosing.

●The detergent may be the cause. Contact the detergent

manufacturer’s consumer care line.

32 electrolux technical data

Technical data

Dimensions Width 59.6 cm

86.8 - 94.8 cm

57.5 cm

Height
Depth

Water supply pressure Minimum 0.05 MPa

0.8 MPa

Maximum

Capacity 12 place settings
Max. weight 43.5 kg

Electrical connection
Voltage - Overall power ­Fuse

Information on the electrical connection is given
on the rating plate on the inner edge of the
dishwasher’s door

Subject to change without notice

technical data electrolux 33

The consumption values are intended
as a guide and depends on the
pressure and the temperature of the
water and also by the variations of the
power supply and the amount of
dishes.

Consumption values

Programme

duration

(in minutes)

Programme Energy

consumption

(in kWh)

Water

consumption

(in litres)

110 - 120Intensive 1.8 - 2.0 23 - 25

90 115Auto 1.1 - 1.5 12 - 23

30Quick 0.9 9

160

Eco

(Test programme
for test institutes)

1.05 15

34 electrolux hints for test institutes

Hints for test institutes

Testing in accordance with EN 60704
must be carried out with appliance
fully loaded and using the test
programme (see "Consumption
values").

Test in accordance with EN 50242
must be carried out when the salt
container and rinse aid dispenser
have been filled with salt and rinse aid
respectively and using the test
programme (see "Consumption
values").

Full load: 12 standard place settings

Amount of detergent required: 5 g + 25 g (Type B)
Rinse aid setting: position 4 (Type III)

Arrangement upper basket

(take off the glass holder)

Arrangement lower basket

Arrangement cutlery

basket

Cup racks: position 2

installation electrolux 35

Any electrical and/or plumbing
work required to install this
appliance should be carried out by
a qualified electrician and/or
plumber or competent person.

Remove all packaging before
positioning the machine.

If possible, position the machine next
to a water tap and a drain.

This dishwasher is designed to be
fitted under a kitchen counter or
worksurface.

Attention! Carefully follow the
instructions on the enclosed template
for building in the dishwasher and
fitting the furniture panel.

No further openings for the venting of
the dishwasher are required, but only
to let the water fill and drain hose and
power supply cable pass through.

The dishwasher incorporates
adjustable feet to allow the
adjustment of the height.

During all operations that involve
accessibility to internal components
the dishwasher has to be unplugged.

When inserting the machine, ensure
that the water inlet hose, the drain
hose and the supply cable are not
kinked or squashed.

Installation

Levelling

Good levelling is essential for correct
closure and sealing of the door.
When the appliance is correctly
levelled, the door will not catch on
either side of the cabinet.
If the door does not close correctly,
loosen or tighten the adjustable feet
until the machine is perfectly level.

Fixing to the adjacent units

The dishwasher must be secured
against tilting.
Therefore make sure that the counter
it is fixed under, is suitably secured to
a fixed structure (adjacent kitchen
units cabinets, wall).

36 electrolux installation

This appliance has been fitted with
safety features which will prevent the
water used in the appliance from
returning back into the drinking water
system. This appliance complies with
the applicable plumbing regulations.

Water supply connections

This dishwasher may be fed with
either hot (max. 60°) or cold water.
Nevertheless we advise you a cold
water supply.

A hot water supply is not always
efficient with very soiled crockery as it
shortens the washing programmes a
lot.

For making the connection itself, the
coupling nut fitted to the machine’s
supply hose is designed to screw onto
a 3/4" gas thread spout or to a
purpose made quick-coupling tap
such as the Press-block.

The water pressure must be within
the limits given in the "Technical
specifications". Your local Water
Authority will advise you on the
average mains pressure in your area.

The water inlet hose must not be
kinked, crushed, or entangled when it
is being connected.

The dishwasher features fill and drain
hoses which can be turned either to
the left or the right to suit the
installation by means of the locknut.

The locknut must be correctly fitted
to avoid water leaks.

(Attention! NOT all models of
dishwashers have fill and drain hoses
provided with locknut. In this case,
this kind of facility is not possible).

If the machine is connected to new
pipes or pipes which have not been
used for a long time, you should run
the water for a few minutes before
connecting the inlet hose.

DO NOT use connection hoses
which have previously been used
for an old appliance.

installation electrolux 37

Water inlet hose with safety valve

After connecting the double-walled
water inlet hose, the safety valve is
next to the tap. Therefore the water
inlet hose is only under pressure
while the water is running. If the water
inlet hose starts to leak during this
operation, the safety valve cuts off the
running water.

Please take care when installing the
water inlet hose:

● The electrical cable for the safety

valve is in the double-walled water
inlet hose. Do not immerse the
water inlet hose or the safety valve
in water.

● If water inlet hose or the safety

valve is damaged, remove the
mains plug immediately.

● A water inlet hose with safety valve

must only by the Service Force
Centre.

● Place the water inlet hose in such

a way that it is never higher than
the bottom edge of the safety
valve.

Warning!
Dangerous voltage

38 electrolux installation

Water outlet hose connection

The end of the drain hose can be
connected in the following ways:

1. To the sink outlet spigot, securing
it to the underside of the work
surface. This will prevent waste
water from the sink running into
the machine.

2. To a stand pipe provided with vent­hole, minimum internal diameter 4
cm.

The waste connection must be at a
height of between 30 cm (minimum)
and 100 cm (maximum) from the
bottom of the dishwasher.

The drain hose can face either to the
right or left of the dishwasher

Ensure the hose is not bent or
squashed as this could prevent or
slow down the discharge of water.

The sink plug must not be in place
when the machine is draining as this
could cause the water to syphon back
into the machine.

If you use a drain hose extension it
must be no longer than 2 metres and
its internal diameter must be no
smaller than the diameter of the hose
provided.

Likewise the internal diameter of the
couplings used for connections to the
waste outlet must be no smaller than
the diameter of the hose provided.

Our appliances are supplied with a
security device to protect against the
return of dirty water back into the
machine.
If the spigot of your sink has a "no
return valve" incorporated this can
prevent the correct draining of your
dishwasher. We therefore advise you
to remove it.

When connecting the drain hose to an
under sink trap spigot, the entire

plastic membrane (A) must be
removed. Failure to remove all the

membrane will result in food particles
building up over time eventually
blocking the dishwasher drain hose
spigot

installation electrolux 39

Electrical connection

Safety standards require the
appliance to be earthed.

Prior to using the appliance for the
first time, ensure that the rated
voltage and type of supply on the
rating plate match that of the
supply where the appliance is to be
installed. The fuse rating is also to
be found on the rating plate.

Always plug the mains plug into a
correctly installed shockproof
socket.

Multi-way plugs, connectors and
extension cables must not be used.
This could constitute a fire hazard
through overheating.

If necessary, have the domestic
wiring system socket replaced. In
case that the electrical cable has to
be replaced, contact your local
Service Force centre.

The plug must be accessible after
the appliance has been installed.

Never unplug the appliance by
pulling on the cable. Always pull
the plug.

The manufacturer accepts no
liability for failure to observe the
above safety precautions.

40 electrolux environment concerns

Packaging material

The packaging materials are
environmentally friendly and can be
recycled. The plastic components are
identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the
packaging materials in the appropriate
container at the community waste
disposal facilities.

When a unit is no longer being used:

- Pull the plug out of the socket.

- Cut off the cable and plug and
dispose of them.

- Dispose of the door catch. This
prevents children from trapping
themselves inside and
endangering their lives.

Environment concerns

Old appliance

The symbol on the product or on
its packaging indicates that this
product may not be treated as
household waste. Instead it shall be
handed over to the applicable
collection point for the recycling of
electrical and electronic equipment.
By ensuring this product is disposed
of correctly, you will help prevent
potential negative consequences for
the environment and human health,
which could otherwise be caused by
inappropriate waste handling of this
product.
For more detailed information about
recycling of this product, please
contact your local city office, your
household waste disposal service or
the shop where you purchased the
product.

warranty/point of service electrolux 41

Warranty/Point of service

Servicestellen Points de service Servizio dopo vendita Point of service

Ersatzteilverkauf / Point de vente de rechange / Vendita pezzi di ricambio /

spare parts service

5506 Mägenwil/Zürich
Industriestr. 10

9000 St. Gallen
Zürcherstrasse 204 e

4127 Birsfelden
Hauptstrasse 52

6020 Emmenbrücke
Seetalstrasse 11

7000 Chur
Comercialstrasse 19

3018 Bern
Morgenstrasse 131

1028 Préverenges Le
Trési 6

6916 Grancia
Zona Industriale E

55

Mägenwil, Industriestrasse 10, Tel. [phone]

Fachberatung, Verkauf/Demonstration, Vente/Consulente (cucina),

Vendita/consulting, sales

8048 Zürich

, Badenerstrasse 587, Tel. [phone]

Service-Helpline

0848 848 111

[e-mail]

42 electrolux warranty/point of service

Garantie

Für jedes Produkt gewähren wir ab Verkauf bzw. Lieferdatum
an den Endverbraucher eine Garantie von 2 Jahren.
(Ausweis durch Garantieschein, Faktura oder Verkaufsbeleg).
Die Garantieleistung umfasst die Kosten für Material, Arbeits­und Reisezeit.

Die Garantieleistung entfällt bei Nichtbeachtung der
Gebrauchsanweisung und Betriebsvorschriften,
unsachgerechter Installation, sowie bei Beschädigung durch
äussere Einflüsse, höhere Gewalt, Eingriffe Dritter und
Verwendung von Nicht-Original Teilen.

Garantie

Nous octroyons sur chaque produit 2 ans de garantie à partir
de la date de livraison ou de la mise en service au
consommateur (documenté au moyen d’une facture, d’un bon
de garantie ou d’un justificatif d’achat). Notre garantie couvre
les frais de mains d’oeuvres et de déplacement, ainsi que les
pièces de rechange.

Les conditions de garantie ne sont pas valables en cas
d’intervention d’un tiers non autorisé, de l’emploi de pièces
de rechange non originales, d’erreurs de maniement ou
d’installation dues à l’inobservation du mode d’emploi, et
pour des dommages causés par des influences extérieures
ou de force majeure.

Garanzia

Per ogni prodotto concediamo una garanzia di 2 anni a
partire dalla data di consegna o dalla sua messa in funzione.
(Fa stato la data della fattura, del certificato di garanzia o
dello scontrino d’acquisto) Nella garanzia sono comprese le
spese di manodopera, di viaggio e del materiale.

Dalla copertura sono esclusi il logoramento ed i danni causati
da agenti esterni, intervento di terzi, utilizzo di ricambi non
originali o dalla inosservanza delle prescrizioni d’istallazione
ed istruzioni per l’uso.

Warranty

For each product we provide a two-year guarantee from the
date of purchase or delivery to the consumer (with a
guarantee certificate, invoice or sales receipt serving as
proof).
The guarantee covers the costs of materials, labour and
travel.

The guarantee will lapse if the operating instructions and
conditions of use are not adhered to, if the product is
incorrectly installed, or in the event of damage caused by
external influences, force majeure, intervention by third
parties or the use of non-genuine components.

117990 83/0 - 00 - 22012007

www.electrolux.com

www.electrolux.ch