Thank you for choosing this AEG product. We have created it to give you
impeccable performance for many years, with innovative technologies that help
make life simpler features you might not find on ordinary appliances. Please
spend a few minutes reading to get the very best from it.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.aeg.com/webselfservice
Register your product for better service:
www.registeraeg.com
Buy Accessories, Consumables and Original spare parts for your appliance:
www.aeg.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
1.
SAFETY INFORMATION
Before the installation and use of the appliance,
carefully read the supplied instructions. The
ENGLISH
manufacturer is not responsible for any injuries or
damages that are the result of incorrect installation or
usage. Always keep the instructions in a safe and
accessible location for future reference.
1.1 Children and vulnerable people safety
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
• Children between 3 and 8 years of age and persons
with very extensive and complex disabilities shall be
kept away from the appliance unless continuously
supervised.
• Children of less than 3 years of age should be kept
away from the appliance unless continuously
supervised.
• Do not let children play with the appliance.
• Keep detergents away from children.
• Keep children and pets away from the appliance when
the door is open.
• Children shall not carry out cleaning and user
maintenance of the appliance without supervision.
3
1.2 General Safety
• This appliance is intended to be used in household
and similar applications such as:
– farm houses; staff kitchen areas in shops, offices
and other working environments;
– by clients in hotels, motels, bed & breakfast and
other residential type environments.
• Do not change the specification of this appliance.
• The operating water pressure (minimum and
maximum) must be between 0.5 (0.05) / 8 (0.8) bar
(MPa)
• Obey the maximum number of 13 place settings.
www.aeg.com4
• If the supply cord is damaged, it must be replaced by
the manufacturer, its Authorised Service Centre or
similarly qualified persons in order to avoid a hazard.
• Put the cutlery in the cutlery basket with the sharp
ends pointing down or put them in the cutlery drawer
in a horizontal position with the sharp edges down.
• Do not leave the appliance with the open door
unattended to avoid stepping accidentally onto it.
• Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the
socket.
• Do not use high pressure water sprays and/or steam
to clean the appliance.
• If the appliance has ventilation openings in the base,
they must not be covered e.g. by a carpet.
• The appliance is to be connected to the water mains
using the new supplied hose-sets. Old hose sets must
not be reused.
2. SAFETY INSTRUCTIONS
2.1 Installation
WARNING!
Only a qualified person must
install this appliance.
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Follow the installation instructions
supplied with the appliance.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Do not install or use the appliance
where the temperature is less than 0
°C.
• Install the appliance in a safe and
suitable place that meets installation
requirements.
2.2 Electrical connection
WARNING!
Risk of fire and electric
shock.
• The appliance must be earthed.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to
the mains plug and to the mains
cable. Should the mains cable need
to be replaced, this must be carried
out by our Authorised Service Centre.
• Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
ENGLISH
5
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• This appliance complies with the
E.E.C. Directives.
• UK and Ireland only. This appliance is
fitted with a 13 A mains plug. If it is
necessary to change the mains plug
fuse, use only a 13 A ASTA (BS 1362)
fuse.
2.3 Water connection
• Do not cause damage to the water
hoses.
• Before connection to new pipes,
pipes not used for a long time, where
repair work has been carried out or
new devices fitted (water meters,
etc.), let the water flow until it is clean
and clear.
• Ensure that there are no visible water
leaks during and after the first use of
the appliance.
• If the water inlet hose is damaged,
immediately close the water tap and
disconnect the mains plug from the
mains socket. Contact the Authorised
Service Centre to replace the water
inlet hose.
2.4 Use
• Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
• Dishwasher detergents are
dangerous. Follow the safety
instructions on the detergent
packaging.
• Do not drink and play with the water
in the appliance.
• Do not remove the dishes from the
appliance until the programme is
complete. Some detergent may
remain on the dishes.
• Do not sit or stand on the open door
of the appliance.
• The appliance can release hot steam
if you open the door while a
programme operates.
2.5 Service
• To repair the appliance contact the
Authorised Service Centre.
• Use original spare parts only.
2.6 Disposal
WARNING!
Risk of injury or suffocation.
• Disconnect the appliance from the
mains supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent
children and pets to get closed in the
appliance.
5
4
8
10
9
11
67
12
2
3
1
www.aeg.com6
3. PRODUCT DESCRIPTION
Worktop
1
Upper spray arm
2
Lower spray arm
3
Filters
4
Rating plate
5
Salt container
6
Air vent
7
Rinse aid dispenser
8
Detergent dispenser
9
Cutlery basket
10
Lower basket
11
Upper basket
12
4. CONTROL PANEL
2
1
3
45
ENGLISH
7
On/off button
1
Display
2
Indicators
3
4.1 Indicators
IndicatorDescription
XtraDry indicator.
Rinse aid indicator. It is always off while the programme operates.
Salt indicator. It is always off while the programme operates.
5. PROGRAMMES
The order of the programmes in the
table may not reflect their sequence on
the control panel.
ProgrammeDegree of soil
Type of load
1)
• Normal soil
• Crockery and
cutlery
Delay button
4
Programme buttons
5
Programme phasesOptions
• Prewash
• Wash 50 °C
• Rinses
• Dry
• XtraDry
www.aeg.com8
ProgrammeDegree of soil
Programme phasesOptions
Type of load
• All
2)
• Crockery, cutlery, pots and
pans
• Prewash
• Wash from 45 °C to 70
°C
• Rinses
• XtraDry
• Dry
• Heavy soil
• Crockery, cutlery, pots and
pans
• Fresh soil
3)
• Crockery and
• Prewash
• Wash 70 °C
• Rinses
• Dry
• Wash 60 °C or 65 °C
• Rinses
• XtraDry
• XtraDry
cutlery
• Normal or light
soil
• Delicate crock-
• Wash 45 °C
• Rinses
• Dry
• XtraDry
ery and glassware
1)
This programme offers the most efficient use of water and energy consumption for crockery and cut-
lery with normal soil. This is the standard programme for test institutes.
2)
The appliance senses the degree of soil and the quantity of items in the baskets. It automatically ad-
justs the temperature and the quantity of water, the energy consumption and the programme duration.
3)
With this programme, you can wash a load with fresh soil. It gives good washing results in a short time.
5.1 Consumption values
Programme
1)
Water
(l)
Energy
(kWh)
Duration
(min)
111.039227
7 - 120.7 - 1.445 - 156
14 - 151.5 - 1.7155 - 170
100.830
13 - 141.0 - 1.175 - 85
1)
The pressure and the temperature of the water, the variations of the mains supply, the options and the
quantity of dishes can change the values.
5.2 Information for test
institutes
To receive the necessary information for
conducting performance tests (e.g.
info.test@dishwasher-production.com
In your request please include the
product number code (PNC) found on
the rating plate.
according to EN60436), send an email to:
For any other questions regarding your
dishwasher please refer to the service
book provided with your appliance.
6. SETTINGS
ENGLISH
9
6.1 Programme selection
mode and user mode
When the appliance is in programme
selection mode it is possible to set a
programme and to enter the user mode.
Settings available in the user mode:
• The level of water softener according
to the water hardness.
• Activation or deactivation of the rinse
aid empty notification.
• Activation or deactivation of AirDry.
As the appliance stores the saved
settings, there is no need to configure
it before every cycle.
How to set the programme
selection mode
The appliance is in programme selection
mode when the programme indicator
is on and the display shows the
programme duration.
After activation, the appliance is in
programme selection mode by default. If
not, set the programme selection mode
the following way:
Press and hold simultaneously
and until the appliance is in
programme selection mode.
To enter user mode, press and hold
simultaneously
the indicators
flash and the display is blank.
and until
, and
6.2 The water softener
The water softener removes minerals
from the water supply, which would have
a negative effect on the washing results
and on the appliance.
The higher the content of these minerals,
the harder your water is. Water hardness
is measured in equivalent scales.
The water softener should be adjusted
according to the hardness of the water in
your area. Your local water authority can
advise you on the hardness of the water
in your area. It is important to set the
right level of the water softener to assure
good washing results.
Softening hard water
increases the consumption
of water and energy as well
as the programme duration.
The higher the level of water
softener, the higher the
consumption and the longer
the duration.
How to enter user mode
Make sure the appliance is in
programme selection mode.
Water hardness
German de-
grees (°dH)
47 - 5084 - 908.4 - 9.058 - 6310
43 - 4676 - 837.6 - 8.353 - 579
37 - 4265 - 756.5 - 7.546 - 528
French degrees
(°fH)
mmol / lClarke de-
grees
Water softener lev-
el
www.aeg.com10
German de-
grees (°dH)
29 - 3651 - 645.1 - 6.436 - 457
23 - 2840 - 504.0 - 5.028 - 356
19 - 2233 - 393.3 - 3.923 - 27
15 - 1826 - 322.6 - 3.218 - 224
11 - 1419 - 251.9 - 2.513 - 173
4 - 107 - 180.7 - 1.85 - 122
<4<7<0.7< 5
1)
Factory setting.
2)
Do not use salt at this level.
Regardless of the type of detergent
used, set the proper water hardness
level to keep the salt refill indicator
active.
Multi-tabs containing salt
are not effective enough to
soften hard water.
How to set the water softener
level
Make sure the appliance is in user mode.
1. Press
French degrees
(°fH)
mmol / lClarke de-
grees
The rinse aid is automatically released
during the hot rinse phase.
When rinse aid chamber is empty, the
rinse aid indicator is turned on notifying
to refill rinse aid. If the drying results are
satisfactory while using multi-tablets
only, it is possible to deactivate the
notification for refilling rinse aid.
However, for best drying performance,
always use rinse aid.
If standard detergent or multi-tablets
without rinse aid are used, activate the
notification to keep the rinse aid refill
indicator active.
• The indicators and
are off.
• The indicator
still flashes.
• The display shows the current
setting: e.g.
2. Press
= level 5.
repeatedly to change
the setting. Each pressing of
increases the level number. After
reaching level 10, the count starts
again from level 1.
3. Press the on/off button to confirm
the setting.
6.3 The rinse aid empty
notification
The rinse aid helps to dry the dishes
without streaks and stains.
How to deactivate the rinse
aid empty notification
Makes ure the appliance is in user mode.
1. Press
• The indicators and are
off.
• The indicator
flashes.
• The display shows the current
setting.
–
= rinse aid empty
notification activated.
= rinse aid empty
–
notification deactivated.
2. Press to change the
setting.
3. Press on/off to confirm the setting.
Water softener lev-
el
1)
5
2)
1
.
still
ENGLISH
11
6.4 AirDry
AirDry improves the drying results with
less energy consumption.
During the drying phase, the
door opens automatically
and remains ajar.
CAUTION!
Do not try to close the
appliance door within 2
minutes after automatic
opening. This can cause
damage to the appliance.
7. OPTIONS
AirDry is automatically activated with all
programmes excluding
applicable).
To improve the drying performance refer
to the XtraDry option or activate AirDry.
CAUTION!
If children have access to the
appliance, it is advised to
deactivate AirDry as opening
the door may pose a danger.
(if
How to deactivate AirDry
Make sure the appliance is in user mode.
1. Press
• The indicators and
• The indicator
• The display shows the current
2. Press
3. Press on/off to confirm the setting.
.
are off.
still flashes.
setting:
– = AirDry activated.
–
= AirDry deactivated.
to change the setting.
Desired options must be
activated every time before
you start a programme.
It is not possible to activate
or deactivate options while a
programme is running.
Not all options are
compatible with each other.
If you select non compatible
options, the appliance
automatically deactivates
one or more of them. Only
the indicators of the still
active options are on.
If an option is not applicable
to a programme, the related
indicator is off or it flashes
quickly for a few seconds
and then goes out.
Activating options can affect
the water and energy
consumption as well as the
programme duration.
7.1 XtraDry
Activate this option to boost the drying
performance. With XtraDry on, the
duration of some programmes, water
consumption and the last rinse
temperature can be affected.
XtraDry is a permanent option for all
programmes other than
need not to be selected at every cycle.
In the other programmes the setting of
XtraDry is permanent and it is
automatically used in next cycles. This
configuration can be changed at any
time.
and
www.aeg.com12
Every time is
activated, XtraDry is off and
needs to be chosen
manually.
8. BEFORE FIRST USE
1. Make sure that the current level of
the water softener agrees with the
hardness of the water supply. If
not, adjust the level of the water
softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start a programme to remove any
processing residuals that can still be
inside the appliance. Do not use
detergent and do not put dishes in
the baskets.
After starting the programme, the
appliance recharges the resin in the
water softener for up to 5 minutes. The
washing phase starts only after this
procedure is complete. The procedure is
repeated periodically.
8.1 The salt container
How to activate XtraDry
Press simultaneously
The indicator
The display shows the updated
programme duration.
4. Carefully shake the funnel by its
handle to get the last granules
inside.
5. Remove the salt around the opening
of the salt container.
is on.
and .
CAUTION!
Use rough salt designed for
dishwashers only. Fine salt
increases the risk of
corrosion.
The salt is used to recharge the resin in
the water softener and to assure good
washing results in daily use.
How to fill the salt container
1. Turn the cap of the salt container
counterclockwise and remove it.
2. Put 1 litre of water in the salt
container (only for the first time).
3. Fill the salt container with 1 kg of salt
(until it is full).
6. Turn the cap of the salt container
clockwise to close the salt container.
CAUTION!
Water and salt can come out
of the salt container when
you fill it. After you fill the
salt container, immediately
start a programme to
prevent corrosion.
A
B
D
C
M
A
X
1
2
3
4
+
-
A
B
D
C
30
20
A BD
C
ENGLISH
13
8.2 How to fill the rinse aid
dispenser
9. DAILY USE
CAUTION!
Only use rinse aid
specifically designed for
dishwashers.
1. Press the release button (D) to open
the lid (C).
2. Fill the dispenser (A) until the rinse
aid reaches the marking ''MAX''.
3. Remove the spilled rinse aid with an
absorbent cloth to prevent too much
foam.
4. Close the lid. Make sure that the
release button locks into position.
You can turn the selector of
the released quantity (B)
between position 1 (lowest
quantity) and position 4 or 6
(highest quantity).
1. Open the water tap.
2. Press the on/off button to activate
9.1 Using the detergent
the appliance.
Make sure that the appliance is in
programme selection mode.
• If the salt indicator is on, fill the
salt container.
• If the rinse aid indicator is on, fill
the rinse aid dispenser.
3. Load the baskets.
4. Add the detergent.
5. Set and start the correct programme
for the type of load and the degree
of soil.
20
30
B
AD
C
www.aeg.com14
CAUTION!
Only use detergent
specifically designed for
dishwashers.
1. Press the release button (B) to open
the lid (C).
2. Put the detergent, in powder or
tablets, in the compartment (A).
3. If the programme has a prewash
phase, put a small quantity of
detergent in the compartment (D).
4. Close the lid. Make sure that the
release button locks into position.
9.2 Setting and starting a
programme
The Auto Off function
This function decreases energy
consumption by deactivating
automatically the appliance when it is not
operating.
The function comes into operation:
• 5 minutes after the completion of the
programme.
• After 5 minutes if the programme has
not started.
Starting a programme
1. Keep the appliance door ajar.
2. Press the on/off button to activate
the appliance. Make sure that the
appliance is in programme selection
mode.
3. Press the button related to the
chosen programme.
The display shows the programme
duration.
4. Set the applicable options.
5. Close the appliance door to start the
programme.
Starting a programme with
delay start
1. Set a programme.
2. Press Delay repeatedly until the
display shows the desired delay time
(from 1 to 24 hours).
The indicator of the selected programme
flashes.
3. Close the appliance door to start the
countdown.
The indicator of the selected programme
is on.
While a countdown is running it is
possible to increase the delay time but
not to change the selection of the
programme and options.
When the countdown is completed, the
programme starts.
Opening the door while the
appliance operates
Opening the door while a programme is
running stops the appliance. It may affect
the energy consumption and the
programme duration. After closing the
door, the appliance continues from the
point of interruption.
If the door is opened for
more than 30 seconds
during the drying phase, the
running programme ends. It
does not happen if the door
is opened by AirDry
function.
Do not try to close the
appliance door within 2
minutes after AirDry
automatically opens it, as
this may cause damage to
the appliance.
If, afterwards, the door is
closed for another 3
minutes, the running
programme ends.
ENGLISH
15
Cancelling the delay start while
the countdown operates
When you cancel the delay start you
have to set the programme and options
again.
Press and hold simultaneously
and until the appliance is in
programme selection mode.
Cancelling the programme
Press and hold simultaneously
and until the appliance is in
programme selection mode.
Make sure that there is detergent in the
detergent dispenser before you start a
new programme.
10. HINTS AND TIPS
10.1 General
Follow the hints below to ensure optimal
cleaning and drying results in daily use
and to help you protect the environment.
• Remove larger residues of food from
the dishes into the waste bin.
• Do not pre-rinse dishes by hand.
When needed, select a programme
with a prewash phase.
• Always use the whole space of the
baskets.
• Make sure that items in the baskets
do not touch or cover each other.
Only then can the water completely
reach and wash the dishes.
• You can use dishwasher detergent,
rinse aid and salt separately or you
can use the multi-tablets (e.g. ''All in
1''). Follow the instructions on the
packaging.
• Select a programme according to the
type of load and the degree of soil.
offers the most efficient use of
water and energy consumption.
10.2 Using salt, rinse aid and
detergent
• Only use salt, rinse aid and detergent
for dishwasher. Other products can
cause damage to the appliance.
End of the programme
When the programme is completed the
display shows 0:00.
All buttons are inactive except for the
on/off button.
1. Press the on/off button or wait for
the Auto Off function to
automatically deactivate the
appliance.
If you open the door before the
activation of Auto Off, the appliance
is automatically deactivated.
2. Close the water tap.
• In areas with hard and very hard water
we recommend to use plain
dishwasher detergent (powder, gel,
tablets containing no additional
agents), rinse aid and salt separately
for optimal cleaning and drying
results.
• At least once a month run the
appliance with the use of appliance
cleaner which is particularly suitable
for this purpose.
• Detergent tablets do not fully dissolve
with short programmes. To prevent
detergent residues on the tableware,
we recommend that you use the
tablets with long programmes.
• Do not use more than the correct
quantity of detergent. Refer to the
instructions on the detergent
packaging.
10.3 What to do if you want to
stop using multi-tablets
Before you start to use separately
detergent, salt and rinse aid do the
following procedure.
1. Set the highest level of the water
softener.
2. Make sure that the salt and rinse aid
containers are full.
Loading...
+ 33 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.