AEG FAVORIT 35085VI User Manual [de]

FAVORIT 35085 Vi

User manual Dishwasher

2

1

Dear Customer

Thank you for choosing one of our highquality products.
With this appliance you will experience the perfect combination of functional
design and cutting edge technology.
Convince yourself that our appliances are engineered to deliver the best per
formance and control  indeed we are setting the highest standards of excel
lence.
In addition to this you find environmental and energy saving aspects as an inte
gral part of our products.
To ensure optimal and regular performance of your appliance please read this
instruction manual carefully. It will enable you to navigate all processes perfect
ly and most efficiently.
To refer to this manual any time you need to, we recommend you to keep it in a
safe place. And please pass it to any future owner of the appliance.
We wish you much joy with your new appliance.

The following symbols are used in this user manual:
Important information concerning your personal safety and information on

3 General information and tips

how to avoid damaging the appliance.

2 Environmental information

Contents

Operating Instructions 4

Safety 4

Diagram of Appliance 5

Control Panel 6

Prior to Using for the First Time 8

Setting the Water Softener 8
Adding dishwasher Salt 10
Filling Up with Rinse Aid 11
Activating/deactivating the acoustic signal 13

In daily use 14

Loading cutlery and dishes 14
Adjusting the Height of the Upper Basket 17
Adding Detergent 18
Using 3 in 1 detergents 20
Selecting the dishwashing cycle (Cycle Table) 21
Starting a dishwashing cycle 23
Setting the delay timer 23
Switching Off the dishwasher 24

Care and cleaning 25

3Contents

What to do if… 27

Remedying small malfunctions 27
If the dishwashing results are not satisfactory 29

Disposal 30

Technical data 30

Notes for Test Institutes 31

Installation and connection instructions 32

Safety Information for the Installation 32

Installing the Dishwasher 32

Connecting the dishwasher 33

Electrical Connection 35

Guarantee/Customer Service 36

Service and Spare Parts 39

Operating Instructions4

Operating Instructions

1 Safety

Prior to using for the first time

• Follow the ”Instructions for installation and connection”.

Correct Use

• The dishwasher is only intended for washing domestic dishes.

• Additions or modifications to the dishwasher are not permitted.

• Use only special salt, detergent and rinse aid suitable for domestic dishwash

ers.

• Do not put any solvents in the dishwasher. This could cause an explosion.

Child Safety

• Keep packaging away from children. There is a risk of suffocation.

• Children often do not recognise the hazards associated with electrical appli

ances. Don’t allow children to use the dishwasher unsupervised.

• Make sure that children and pets don’t climb into the dishwasher. Could en
danger life!

• Dishwasher detergents can cause chemical burns to the eyes, mouth and
throat. Could endanger life! Comply with the safety instructions of the dish
washer detergent manufacturer.

• The water in the dishwasher is not for drinking. Risk of chemical burns.

General Safety

• Repairs to the dishwasher are only to be carried out by qualified/authorised
service engineers.

• When the dishwasher is not being used, switch it off and shut off the water
tap.

• Never unplug the appliance by pulling on the cable. Always pull the plug.

• Ensure that the door of the dishwasher is always closed when it is not being

loaded or unloaded. In this way you will avoid anybody tripping over the open
door and hurting themselves.

• Never sit or stand on the open door.

• If the dishwasher is located in a room where there may be a frost, remove the

connection hose from the tap after each use of the dishwasher.

Diagram of Appliance

Upper basket spray arm
and lower spray arm

Water softener
unit.

Salt Container

Detergent
Dispenser

Rinse aid
dispenser

5Diagram of Appliance

Control panel

Rating plate

Filters

Control Panel6

Control Panel

To use the appliance, always open the dishwasher door first.

ON/OFF button

The ON/OFF button is used to turn the dishwasher on and off.

Programme displays

Programme display 2

Control
indicators

Programme

timer

button

The programme button is used to:

– set the water softener
– set the acoustic signal
– select the programme
– cancel a dishwashing cycle.

End of cycle indicatorSet delay

The control indicators have the following meanings:

1)

1)

1) These control indicators are never illuminated while a dishwashing cycle is running.

Refill with dishwasher salt

Refill with rinse aid

7Control Panel

Prior to Using for the First Time8

Prior to Using for the First Time

3

If you wish to use 3 in 1 detergent:
– First read the section “Using 3 in 1 detergents”.
– Do not fill up with special salt or rinse aid.

If you do not use 3 in 1 detergent, before using for the first time

1. Set the water softener

2. Fill up with dishwasher salt

3. Fill up with rinse aid

Setting the Water Softener

The water softener must be set manually and electronically:

3 To avoid scale deposits on the dishes and in the dishwasher, the dishes must be

washed with soft water, i.e. water with a low lime content. The water softener
must be set according to the table to the water hardness in the area where you
live. Your local water company will be able to give you information about the
water hardness in your area.

The dishwasher must be switched off.

Setting manually:

1. Open the dishwasher door.

2. Remove the lower basket from the

dishwasher.

3. Turn water hardness dial on the left wall of
the dishwasher interior to 1 or 2 (see table).

Setting electronically:

1. Press the ON/OFF button.

3 If a programme display is illuminated, this wash programme is activated. The

wash programme must be deselected:
Press and hold the programme button for approx. 3 seconds.
The programme display goes out. The indicator for the end of the wash pro
gramme flashes.

2. Press and hold the programme button for approx. 3 seconds.
Programme display 2 will light up and go out after approx. 3 seconds. The indi
cator for the programme button will flash.
The indicator for the end of the dishwashing cycle will flash simultaneously:

– The number of times that the indicator for the end of the dishwashing cycle

flashes corresponds to the hardness setting.

– This sequence of flashes is repeated several times, with a 3 second pause in

between.

3. Pressing the programme button increases the hardness setting by 1.
(Exception: hardness setting 1 follows hardness setting 10).

4. When the hardness setting is correct, press the ON/OFF button.
The hardness setting is now saved.

If the water softener is set electronically to “1”, this switches off the control in
dicator for special salt.

9Prior to Using for the First Time

Water hardness Adjusting the hardness setting

1)

in °d

51  70
43  50
37  42
29  36
23  28

19  22
15  18

11  1 4 1,9  2,5 II 3 3

4  10 0,7  1,8 I/II 2 2

below 4 below 0.7 I

1) (°d) German degree, measure of the hardness of water

2) [mmol/l] millimol per litre, international unit for water hardness

3) On this setting the length of the dishwashing cycle may be slightly longer.
*) factory setting

in mmol/l

9,0  12,5

7,6  8,9
6,5  7,5
5,1  6,4
4,0  5,0

3,3  3,9
2,6  3,2

2)

Range Manual Electronic

IV

III

2*

1

3)

10

9
8
7
6

5*

4

1

no salt

necessary

Number of

flashes

10

9
8
7
6

5
4

1

Prior to Using for the First Time10

Adding dishwasher Salt

To decalcify the water softener, it must be filled up with dishwasher salt. Use
only special salt suitable for domestic dishwashers.

If you do not use 3 in1 detergent, fill up with dishwasher salt:

– Before using the dishwasher for the first time.
– When the control indicator for dishwasher salt is illuminated on the control

panel.

1. Open the door and remove the lower
basket.

2. Unscrew the lid on the salt dispenser by
turning it anticlockwise.

3. Only when using the dishwasher for the
first time:

Fill the salt dispenser with water.

4. Place the funnel (supplied) over the dis
penser opening.
Fill the dispenser with dishwasher salt; the
capacity of the dispenser is approx. 1.01.5
kg, depending on the size of the grains. Do
not overfill the dispenser.

3 If water overflows when filling up with dishwasher salt, this is completely harm

less.

5. Clean away any salt remnants from the dispenser opening.

6. Screw the lid back on in a clockwise direction.

7. Run a dishwashing cycle after filling the salt dispenser with dishwasher
salt. This will wash away salt water and salt crystals that have been spilt.

3 Depending on the size of the salt granules, it can take several hours for the salt

to dissolve in the water and for the control indicator for dishwasher salt to go
out.

Filling Up with Rinse Aid

Rinse aid causes the rinse water to flow easily from the crockery leaving gleam
ing dishes and glassware.

If you do not use 3in1 detergent, fill up with rinse aid:

– Before using the dishwasher for the first time.
– When the control indicator for rinse aid is illuminated on the control panel.

Use only special rinse aid for dishwashers.

1. Open the door.
The rinse aid compartment is located on
the inside of the dishwasher door.

2. Press the release button on the rinse aid
compartment.

3. Open the cover.

4. Pour rinse aid in slowly right up to the bro

ken “max” line;
this corresponds to a volume of approx.
140 ml when full.

5. Press the lid shut until it clicks into place.

6. Wipe up any spilt rinse aid with a cloth.

Otherwise there will be too much foam
when rinsing.

11Prior to Using for the First Time

Prior to Using for the First Time12

Setting the Amount of Rinse Aid Required

3 Only change the amount dispensed, if smears, milky spots (reduce the amount)

or dried on water spots (increase the amount) can be seen on glasses and dishes.
(See section “If dishwashing results are not satisfactory”.) The dosage can be set
from 16. The dosage is preset to “4” in the factory.

1. Open the dishwasher door.

2. Press the release button on the rinse aid

compartment.

3. Open the cover.

4. Set the dosage level.

5. Press the lid shut until it clicks into place.

6. If rinse aid has leaked out, wipe it away

with a cloth.

Activating/deactivating the acoustic signal

In addition to the optical display (e.g. indicating the end of the cycle, errors) you
can also choose to set an acoustic signal.

1. Press the ON/OFF button.

3 If a programme display is illuminated, this wash programme is activated. The

wash programme must be deselected:
Press and hold the programme button for approx. 3 seconds.
The programme display goes out. The indicator for the end of the wash pro
gramme flashes.

2. Press the programme button.The indicator for the programme button will flash.
Programme display 2 will light up.

3. Press the programme button again within 3 seconds.
The indicator for the programme button will change from flashing to continual
illumination and will go out after approx. 3 seconds.
Programme display 2 flashes.
The end of wash programme indicator displays the current setting:

13Prior to Using for the First Time

End of wash programme indicator is
illuminated:

End of wash programme indicator is
not illuminated:

Acoustic signal activated
(factory setting)

Acoustic signal deactivated

4. By pressing the programme button you can turn the acoustic signal on and off.

5. If the acoustic signal is set as desired, press the ON/OFF button.

The setting for the acoustic signal has now been saved.

In daily use14

In daily use

Loading cutlery and dishes

1 Sponges, cleaning cloths and any other objects that can absorb water must not

be washed in the dishwasher. Plastic and Tefloncoated dishes and pans tend to
retain water droplets. These dishes and pans therefore do not dry as well as
those made of china and stainless steel.

For washing in the dishwasher, the following cutlery/dishes/pots and pans

are not suitable: are of limited suitability:

• Cutlery with wooden, horn, china or
mother of pearl handles

• Plastic items that are not heat re
sistant

• Older cutlery with cement
that is sensitive to temperature

• Dishes or cutlery with glued parts

• Pewter or copper items

• Lead crystal glass

• Steel items that rust

• Wooden boards/platters

• Items made from synthetic materials

• Before loading the dishes, you should:
– Remove the worst of the food residues.

– Soak pans with burnton food residues.

• When loading the dishes and cutlery, please note:
– Dishes and cutlery must not impede the rotation of the spray arms.

– Load bowls, cups, glasses, pans, etc. with the opening downwards so that

water cannot collect in them

– Dishes and items of cutlery must not lie inside one another or cover one an

other

– To avoid damage to glasses, they must not touch one another
– Don’t put small items (e.g. lids) in the baskets for the dishes, but in the cut

lery basket, so that they can’t fall through the holes.

• Only wash stoneware in the dishwasher if it is spe
cifically marked by the manufacturer as being dish
washersafe.

• Glazed patterns may fade if washed very frequently
in the dishwasher.

• Silver and aluminium parts have a tendency to dis
colour during washing. Food remains, e.g. egg white,
egg yolk and mustard often cause discoloration and
staining on silver. Therefore always clean food resi
dues from silver immediately, if it is not to be
washed straight after use.

• Glass can become dull after a large number of wash
es.

15In daily use

Loading cutlery

1 Warning: Sharp knives and other items of cutlery with sharp edges must be laid

in the cutlery rack or in the upper basket to avoid the risk of injury.
To ensure that all items of cutlery in the cutlery basket can be reached by the

water, you should:

1.Place the grid insert on the cutlery
basket

2.Place forks and spoons in the cutlery
basket's grid insert with their han
dles pointing downwards.

Pots, Pans, Large Plates

Load larger and heavily soiled dishes and
pans in the lower basket.
(Max. diameter for plates 29 cm).

In daily use16

To make it easier to load larger dishes, the
two plate racks on the right in the lower
basket can be folded down.

Cups, Glasses, Coffee Service

Load smaller, fragile crockery and long,
sharp cutlery in the upper basket.

• Arrange items of crockery on and under
the folding cup racks so that they are
offset from each other and water can
reach all items.

• The cup racks can be folded up out of the
way for tall crockery items.

• Lay or hang wine and brandy glasses in
the slots in the cup racks.

Adjusting the Height of the Upper Basket

Maximum height of dishes in the

Upper basket Lower basket

with upper basket raised 22 cm 30 cm

with upper basket lowered 24 cm 29 cm

3 The height of the baskets can also be adjusted when they are loaded.

Raising / Lowering the upper basket

1. Pull out the upper basket completely.

2. Holding the upper basket by the handle,

raise it as far as it will go and then lower it
vertically.
The upper basket will latch into the lower
or the upper position.

17In daily use

In daily use18

Adding Detergent

Detergents remove the dirt from dishes and
cutlery.
The detergent must be added before the
cycle starts.

1 Only use detergent intended for domestic

dishwashers.
The detergent compartment is located on

the inside of the door.

1. If the lid is closed:
Press the release button.
The lid will spring open.

2. Place the detergent in the detergent dis
penser. The markings indicate the dosing
levels for powder detergents: “20/30” cor
responds to approx.
20/30 ml of detergent.
Follow the manufacturer’s instructions
with regard to dosing and storage.

3. Close the lid and press until it locks into
place.

3 In the case of very heavily soiled dishes, fill

the adjoining compartment (1) with addi
tional detergent. This detergent comes into
use during the prewash cycle.

19In daily use

Concentrated detergents

Today’s detergents for dishwashers are almost exclusively lowalkaline concen
trated detergents with natural enzymes in tablet or powder form.

2 Using 50°C dishwashing cycles in conjunction with these concentrated deter

gents reduces pollution and is good for your dishes, as these dishwashing cycles
are specially matched to the dirtdissolving properties of the enzymes in con
centrated detergents. It is for this reason that using 50 °C dishwashing cycles in
conjunction with concentrated detergents can achieve the same cleaning results
that can otherwise only be achieved using 65 °C cycles.

Detergent tablets

3 Detergent tablets from different manufacturers dissolve at different rates. For

this reason, some detergent tablets do not attain their full cleaning power dur
ing short cycles. Therefore please use dishwashing cycles with prewash when
using detergent tablets.

In daily use20

Using 3 in 1 detergents

These products are detergents with a combined cleaning, rinsing and salt func
tion.

If you want to use 3 in 1 products

1. There is no need to fill up with special salt or rinse aid.

2. Set the water softener to water hardness range “I”.

3. Set the rinse aid dosage to “1”.

Before the start of the dishwashing cycle put 3in1 detergent in the detergent
dispenser.

If you do not want to use 3 in 1 products any more

If you want to stop using 3in1 products, please do the following:

• Fill up the dispensers for salt and rinse aid again.

• Switch the water softener to the highest setting and perform up to three nor

mal cycles without loading any dishes.

• Then set the water softener to the water hardness in your area.

If you want to use 4 in 1 products

When using "4 in 1" detergents that integrate also anti glass corrosion agent
into "3 in 1" formula, please follow the same indication as given for "3 in 1" de
tergents.

Selecting the dishwashing cycle (Cycle Table)

21In daily use

Dishwashing

cycle

Suitable

for:

Type of

soiling

Programme

sequence

Prewash

Main wash

Intermediate rinse

Final rinse

Drying

Consumption

values

Length (minutes)

1)

Energy (kWh)

heavily soiled,

INTENSIV

CARE 70°

30 MIN

(60°)

2)

3)

NORMAL 65°

Dinner service and
cookware

Dishes, excluding
saucepans

Dinner service and
cookware

driedon food remains,
in particular protein
and starch

just used, lightly to nor
mally soiled

normally soiled
driedon food remains

• •

2x

• •

 •  • 

• • • • •

120  130

1,80  2,00

30

0,8

95  105

1,40  1,60

Dinner service and
cookware, tempera

ECO 50°

4)

turesensitive
crockery

normally soiled • • • • •

130  160

0,95  1,05

Used dishes that are be

(cold)

5)

All types of dishes

ing stored in the dish
washer and are to be

•    

12

< 0,1

washed later.

1) The consumption values were obtained under standardised conditions. They depend on how full the bas
kets for the dishes are. Variations are therefore possible in practice.

2) During the final rinse, the temperature is increased to 68° for 10 minutes to sanitize e.g. plastic chopping
boards or jam jars.

3) When using this cycle, only load the dishwasher half full.

4) Test programme for Test Institutes

5) This cycle does not need any detergent.

Water (litres)

23  25

9

17  19

14  16

4

In daily use22

Selecting a programme

When your dishes look like this, select:
an intensive programme.

a normal or energysaving programme.

a short programme (e.g. 30 minute pro
gramme).

Starting a dishwashing cycle

1. Check that the spray arms can turn freely.

2. Turn the water tap on fully.

3. Press the ON/OFF button.

4. Select the required programme by repeatedly pressing the programme button.

The display for the selected programme lights up.

5. Close the door. The wash programme will begin.

Interrupting or Cancelling a dishwashing cycle

Interrupt a dishwashing cycle that is in progress if it is absolutely necessary.

Interrupting the dishwashing programme by opening the dishwasher door

1 Hot steam may escape when the door is opened. There is a risk of scalding.

1. Open the door carefully. The dishwashing cycle will stop.

2. Close the door. The cycle will continue.

Cancelling the dishwashing cycle

1. Press and hold the programme button for approx. 3 seconds.

The programme display goes out.
The indicator for the end of the wash programme flashes.
The dishwashing cycle has been cancelled.

2. Switch off using the ON/OFF button.

3. If you want to start a new dishwashing cycle, check whether there is any deter

gent in the dispenser.

23In daily use

Setting the delay timer

With the delay timer you can delay the start of a dishwashing cycle for 3 hours.

1. Press the ON/OFF button.

2. Press delay timer button. The delay timer indicator is illuminated.

3. Select dishwashing cycle.

The programme display will light up.

4. Close the door.The dishwashing cycle will start automatically when 3 hours have
elapsed.

Cancelling the delay timer:

Press the delay timer button. The hours indicator goes out. The selected pro
gramme will begin immediately once the door is closed.

In daily use24

Switching Off the dishwasher

If the acoustic signal has been enabled, 5 short tones will sound at the end of
the dishwashing cycle.

1 Carefully open the door. Hot steam may escape.

• Hot dishes are sensitive to knocks. Therefore leave the dishes to cool for about

15 minutes before removing them. You also get a better drying result.

• Dishes dry more quickly if you open the door for a moment after the cycle has

ended and then leave it slightly open.

1. Press the ON/OFF button. All display indicators will go out.

2. Turn off the water tap.

Removing the Dishes

3 It is normal for the inner door and the dispensers to be damp.

• Empty the lower basket first, then the upper basket. This way you avoid drip

ping water from the upper basket onto dishes in the lower basket.

Care and cleaning

25Care and cleaning

1

Do not use furniture care products or aggressive cleaners.

• When necessary, clean the dishwasher’s controls with a soft cloth.

• Occasionally check the internal dispensers, door seal and water inlet filter (if

fitted) for dirt and clean them, if necessary.

Cleaning the filters

3 The filters must be regularly checked and

cleaned. Dirty filters will spoil the wash re
sults, and may lead to malfunction of your
dishwasher.

1. Open the door and remove the lower basket.

2. Turn the handle about ¼ of a turn anticlock

wise (A) and remove the filter system (B).

3. Grasp the grip hole on the fine filter (1) and
remove it from the microfilter (2).

4. Clean all filters thoroughly under running
water.

Care and cleaning26

5. Remove the flat filter (3) from the base of
the washing compartment and clean both
surfaces thoroughly.

6. Reinsert the flat filter.

7. Place the fine filter in the microfilter and fit

the two together.

8. Insert the filter system in place and lock it by
turning the handle clockwise as far as it will
go. Ensure that the flat filter does not pro
trude above the base of the washing com
partment.

1 Under no circumstances may the dishwasher be used without its filters.

What to do if…

Remedying small malfunctions

Before you call the Customer Care Department, please check whether
– you cannot remedy the fault yourself with the help of the following fault ta

ble
or
– whether it is caused by faulty, electrical connections and/or faulty water con

nections.
In these cases the engineer must make you liable for the costs of the Customer
Service intervention even during the warranty period.
If the acoustic signal is activated, warning tones sound if there are faults.
If while the appliance is operating indicators on the control panel flash or are lit
up as described in the following table, please consult this to find out how to
remedy the fault.
After remedying the fault that is flashing in the first or second rhythm in the
programme progress display, press the button for the dishwashing cycle that
had already started. The cycle will continue.
In the case of other fault messages:

– Cancel the dishwashing cycle.
– Switch the appliance off and on again.
– Select dishwashing cycle.

If the fault is displayed again, please contact the Service Force Centre and in
form them of the fault message.

27What to do if…

Malfunction Possible cause Remedy

1 short warning tone, con
tinuously repeated, can be
heard,
the programme display for
the selected wash programme
is flashing:
the indicator for the end of
the wash programme is flash
ing once continuously .
(problems with water inflow).

Tap is blocked with limescale or
is faulty.

The tap is turned off. Turn on the tap.

The filter (where present) in the
threaded hose fitting on the
tap is blocked.

Filters in the base of the wash
ing compartment are blocked.

Water inflow hose has not
been correctly positioned.

Check the tap and have it re
paired, if necessary.

Clean the filter in the threaded
hose fitting.

Cancel the dishwashing cycle
(see chapter: Starting a dish
washing cycle),
clean filters (see chapter:
Cleaning the filters),
then start the dishwashing cy
cle again.

Check the position of the hose.

What to do if…28

Malfunction Possible cause Remedy

2 short warning tones, con
tinuously repeated, can be
heard,
the programme display for
the selected wash programme
is flashing,
the indicator for the end of
the wash programme is flash
ing twice continuously .
(Rinse water has collected in
the dishwasher's interior con
tainer).

3 short warning tones, con
tinuously repeated, can be
heard,
the indicator for the end of
the wash programme is flash
ing three times continuously .

The programme is not start
ing.

Rust spots are visible in the
dishwashing compartment.

A whistling noise can be
heard when washing dishes.

The siphon is blocked. Clean the siphon.

Water drain hose has not been
correctly positioned.

The antiflood system has been
triggered.

The mains plug is not plugged
in.

A fuse in the house’s wiring
system is defective.

For dishwasher models with a
start delay timer:
A start time has been selected.

Check the position of the hose.

First turn off the water tap,
then switch off the appliance
and contact customer service.

Connect the plug to a mains
socket.

Replace fuse.

If the dishes are to be washed
immediately, cancel the start
delay.

The dishwashing compart
ment is made from rustfree
stainless steel. Rust spots in
the dishwashing compartment
are due to rust particles from
external sources (rust particles
from water pipes, pans, cutlery,

Only wash cutlery, dishes and
pans that are suitable for dish
washer use.

etc.). Remove such spots with a
commercially available clean
ing product for stainless steel.

Decalcify appliance with com
mercially available agents for

cleaning dishwashers.
The whistling is not a cause for
concern.

If the noises can still be heard

after decalcifying the machine,

use a different brand of deter

gent for washing cutlery and

dishes.

If the dishwashing results are not satisfactory

The dishes are still dirty.

• The wrong dishwashing cycle was selected.

• The dishes were loaded is such a way that the dishwashing water did not

reach all items. The baskets for the dishes must not be overloaded. The spray
arms must be free to turn.

• Filters in the floor of the dishwasher are not clean or incorrectly inserted.

• Good quality detergent was not used, or too little was used.

• In the case of scale deposits on the dishes: The special salt dispenser is empty

or the water softening system has been incorrectly set.

• The drain hose is incorrectly positioned.

• If at the end of the dishwashing cycle there is still detergent left in the deter

gent dispenser, either the spray arm was jammed or the spray arm jets are
blocked with pollutants in the dishwashing water.
You have the option of removing the spray arms from their fixture for clean
ing (see section “Care and Cleaning”).

The dishes do not dry and are not shining.

• Poor quality rinse aid was used.

• The rinse aid dispenser is empty.

There are smears, streaks, milky spots or a shiny bluish coating on glasses
and dishes.

• Lower rinse aid dosage.

There are dried water drops on the glasses and dishes.

• Increase rinse aid dosage.

• The detergent may be the cause. Contact the detergent manufacturer's cus

tomer advice centre.

Glass corrosion

• Contact the detergent manufacturer's customer advice centre.

29What to do if…

Disposal30

Disposal

2

Packaging material

The packaging materials are environmentally friendly and can be recycled. The
plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dis
pose of the packaging materials in the appropriate container at your local waste
disposal facilities.

2 Old appliance

The symbol W on the product or on its packaging indicates that this product

may not be treated as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and electronic equip
ment. By ensuring this product is disposed of correctly, you will help prevent po
tential negative consequences for the environment and human health, which
could otherwise be caused by inappropriate waste handling of this product. For
more detailed information about recycling of this product, please contact your
local city office, your household waste disposal service or the shop where you
purchased the product.

1 Warning! When your appliance has finished its working life, remove the plug

from the socket. Cut off the cable and plug and dispose of them.
Break the door lock so that the door no longer shuts. This prevents children from
trapping themselves inside and endangering their lives.

Technical data

Capacity: 12 place settings including serving dishes

Permitted water pressure: 0.11.0 MPa (= 10100 N/cm2 = 110 bar )

Electrical connection: Also see the rating plate on the righthand side of the dishwasher’s

Dimensions: 820  880 x 596 x 555 (H x W x D in mm)

Max. weight: 45 kg

5

interior door .

Notes for Test Institutes

Testing in accordance with EN 60704 must be carried out with the appliance
fully loaded and using the test cycle (see “Cycle Table”).
Tests in accordance with EN 50242 must be carried out when the salt dis
penser in the water softener and the rinse aid dispenser have been filled with
salt and rinse aid respectively, and using the test cycle (see “Cycle Table”).

Amount of detergent required: 5g + 25g (Type B)

Rinse aid setting: 4 (Type III)

31Notes for Test Institutes

Full load:

12 place settings including serving dishes

Example loading arrangements:

Upper basket

*) If there are cup racks in place on the lefthand side or the cutlery tray is in place, remove them.

Lower basket with cutlery basket

*)

*)

Cutlery basket

*) If necessary, you can remove the cup racks on the lefthand side and/or the beer glass holder.

Installation and connection instructions32

Installation and connection instructions

1 Safety Information for the Installation

• Only transport the dishwasher in an upright position, otherwise salt water
may run out.

• Before using the dishwasher for the first time, check for any damage caused in
transport. Do not under any circumstances connect an appliance that is dam
aged. In the case of damage, please contact your supplier.

• Never use the dishwasher if the mains cable, water inlet or drain hose are
damaged; or if the control panel, work top or plinth area are damaged such
that the inside of the appliance is freely accessible.

• Always plug the mains plug into a correctly installed shockproof socket.

• Prior to using the appliance for the first time, ensure that the rated voltage

and type of supply on the rating plate match that of the supply where the ap
pliance is to be installed. The fuse rating is also to be found on the rating plate.

• Multiway plugs / connectors and extension cables must not be used. This
could constitute a fire hazard through overheating.

• The dishwasher’s cable must only be replaced by a Service Force Engineer.

• A water inlet hose with safety valve must only be replaced by a Service Force

Engineer.

Installing the Dishwasher

• The dishwasher must be installed on a firm floor and adjusted to ensure that it
is stable and level in all directions.

• To compensate for unevenness in the floor and to match the height of the ap
pliance to that of surrounding units, extend the threaded feet using a screw
driver.

• Adjust the rear foot of the appliance using a cordless screwdriver from the
front of the appliance (see installation template).

• The drain hose, inlet hose and mains cable must be laid so that they are able to
move freely within the plinth area, and so that they are not kinked or crushed
when the dishwasher is in position.

• The dishwasher must also be screwed tightly to the work surface or to the ad
joining units. This is essential to ensure the dishwasher does not tip up.

Dishwashers That Can be Integrated

(see installation template supplied)
Using the installation template supplied, split cupboard doors can be easily in

stalled and firmly fitted.

Connecting the dishwasher

Connecting to the water supply

• The dishwasher can be connected to cold or hot water supplies up to max.
60°C.

• The dishwasher must not be connected to open hot water appliances or in
stantaneous water heaters.

Permitted water pressure

33Connecting the dishwasher

Lowest permitted water pressure:
0,1 MPa ( = 1 bar = 10 N/cm

Highest permitted water pressure:

1 MPa ( = 10 bar = 100 N/cm

2

)

2

)

Consult your plumber if the water pressure is
less than 0,1 MPa

If the water pressure is greater than
1 MPa, a pressure reduction valve must be used
(available from your dealer).

Connecting the inlet hose

1 The water inlet hose must not be kinked, crushed or entangled when it is being

connected.
Connect the threaded hose fitting (ISO 2281:2000) on the water inlet hose to a
tap with an external thread (¾ inch). The inlet hose is fitted with either a plastic
or a metal nut:
– Only tighten the nut hand tight.
Then do a visual check for water tightness. (Make sure that the tap is not drip
ping.)

3 So that access to the tap in the kitchen is not restricted by the use of the dish

washer, we recommend installing an additional tap, or fitting a Tbranch to the
existing tap.

Connecting the dishwasher34

1 WARNING!  Dangerous voltage

(This does apply to dishwashers with safety
valve).
The electrical cable for the safety valve is in
the doublewalled water inlet hose and is
live.
Therefore do not immerse the water inlet
hose or the safety valve in water.



Water drainage

Drain hose

1 The drain hose must not be kinked, crushed or entangled.

Connecting the drain hose:

– Maximum permitted height: 1 metre.
– Minimum required height: 40 cm above the bottom edge of the appliance.

Extension hoses

• Extension hoses are available from your lo
cal Service Force Centre. To ensure that the
function of the appliance is not impeded,
the internal diameter of extension hoses
must be 19 mm.

• Extension hoses must not be laid more
than a maximum distance of 4 metres
horizontally; the maximum permitted
height for the connection for the drain
hose is then 85 cm.20

Sink outlet connection

• The outlet of the drain hose (ø 19 mm) fits all commonly available sink outlet
types. The outer diameter of the sink outlet connection must be at least
15 mm.

• The drain hose must be fixed to the sink outlet connection using the hose
clamp supplied.

Antiflood system

For protection from water damage, the dishwasher is equipped with a antiflood
system.
In the event of a fault, the safety valve in the water inlet hose immediately in
terrupts the supply of water to the appliance.

Electrical Connection

G

Any electrical work required to install this appliance should be carried out
by a qualified electrician or competent person.

1 WARNING  This appliance must be earthed.

The manufacturer declines any responsibility should these safety meas
ures not be observed.

Before switching on make sure the electricity supply voltage is the same as that
indicated on the appliance rating plate.

To isolate the dishwasher from the mains, remove the mains plug.
Important: The plug must still be accessible after the appliance has been in
stalled.

Changing a fuse

The appliance is supplied with a 13amp plug fitted. In the event of having to
change the fuse in the plug supplied, a 13amp ASTA approved (BS 1363A) fuse
must be used.

Should the plug need to be replaced for
any reason, proceed as described below.

The wires on the mains lead are coloured in
accordance with the following code.

35Connecting the dishwasher

reen & Yellow

Green and Yellow: Earth
Blue: Neutral
Brown: Live

• The wire coloured green and yellow must
be connected to the terminal marked
with the letter “E“ or by the earth symbol E or coloured green and yellow.

• The wire coloured blue must be connected to the terminal “N“ or coloured
black.

• The wire coloured brown must be connected to the terminal marked “L“ or col
oured red.

• Upon completion there must be no cut, or stray strands of wire present and
the cord clamp must be secure over the outer sheath.

Blue

Brown

Cord Clamp

1 WARNING! A cut off plug inserted into a 13 amp socket is a serious safety

(shock) hazard. Ensure that, if it is necessary to cut off the plug, it is dis
posed of safely and not retained.

Guarantee/Customer Service36

Guarantee/Customer Service

Standard guarantee conditions

We, AEGElectrolux, undertake that if within 12 months of the date of the pur
chase this AEGElectrolux appliance or any part thereof is proved to be defective
by reason only of faulty workmanship or materials, we will, at our option repair
or replace the same FREE OF CHARGE for labour, materials or carriage on condi
tion that:

• The appliance has been correctly installed and used only on the electricity
supply stated on the rating plate.

• The appliance has been used for normal domestic purposes only, and in ac
cordance with the manufacturer’s instructions.

• The appliance has not been serviced, maintained, repaired, taken apart or tam
pered with by any person not authorised by us.

• Electrolux Service Force Centre must undertake all service work under this
guarantee

• Any appliance or defective part replaced shall become the Company’s proper
ty.

• This guarantee is in addition to your statutory and other legal rights.

Exclusions

• Damage or calls resulting from transportation, improper use or neglect, the
replacement of any light bulbs or removable parts of glass or plastic.

• Costs incurred for calls to put right an appliance which is improperly installed
or calls to appliances outside the United Kingdom.

• Appliances found to be in use within a commercial environment, plus those
which are subject to rental agreements.

• Products of Electrolux manufacturer that are not marketed by Electrolux

37Guarantee/Customer Service

European Guarantee

This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for
the period specified in the appliance guarantee or otherwise by law. If you move from one of these coun
tries to another of the countries listed below the appliance guarantee will move with you subject to the fol
lowing qualifications:

•

The appliance guarantee starts from the date you first purchased the appliance which will be evidenced
by production of a valid purchase document issued by the seller of the appliance.

•

The appliance guarantee is for the same period and to the same extent for labour and parts as exists in
your new country of residence for this particular model or range of appliances.
The appliance guarantee is personal to the original purchaser of the appliance and cannot be transferred

•

to another user.

•

The appliance is installed and used in accordance with instructions issued by Electrolux and is only used
within the home, i.e. is not used for commercial purposes.

The appliance is installed in accordance with all relevant regulations in force within your new country of

•

residence.

The provisions of this European Guarantee do not affect any of the rights granted to you by law.

www.electrolux.com

p t b

Albania [phone] Rr. Pjeter Bogdani Nr. 7 Tirane

Belgique/België/
Belgien

Èeská republika [phone] Budìjovická 3, Praha 4, 140 21

Danmark [phone] Sjællandsgade 2, 7000 Fredericia

Deutschland [phone] Muggenhofer Str. 135, 90429 Nürnberg

Eesti [phone] Mustamäe tee 24, 10621 Tallinn

España [phone]

France www.electrolux.fr

Great Britain [phone]

Hellas [phone] Limnou Str., 54627 Thessaloniki

Hrvatska [phone] Slavonska avenija 3, 10000 Zagreb

Ireland [phone] Long Mile Road Dublin 12

Italia [phone] C.so Lino Zanussi, 26  33080 Porcia (PN)

Latvija [phone] Kr. Barona iela 130/2, LV1012, Riga

Lithuania [phone] Žirmūnų 67, LT09001 Vilnius

Luxembourg [phone] Rue de Bitbourg, 7, L1273 Hamm

Magyarország [phone]

[phone] Bergensesteenweg 719, 1502 Lembeek

Carretera M300, Km. 29,900
Alcalá de Henares Madrid

Addington Way, Luton, Bedfordshire
LU4 9QQ

H1142 Budapest XIV,
Erzsébet királyné útja 87

Guarantee/Customer Service38

p t b

Nederland [phone]

Norge [phone] Risløkkvn. 2 , 0508 Oslo

Österreich [phone] Herziggasse 9, 1230 Wien

Polska [phone] ul. Kolejowa 5/7, Warszawa

Portugal [phone]

Romania [phone] Str. Garii Progresului 2, S4, 040671 RO

Schweiz/Suisse/
Svizzera

[phone] Industriestrasse 10, CH5506 Mägenwil

Slovenija [phone]

Slovensko [phone]

Suomi www.electrolux.fi

Sverige [phone]

Türkiye [phone]

Россия [phone]

Vennootsweg 1, 2404 CG 
Alphen aan den Rijn

Quinta da Fonte  Edificio Gonçalves Zarco  Q 35
2774  518 Paço de Arcos

Electrolux Ljubljana d.o.o.
Gerbièeva 98, 1000 Ljubljana

Electrolux Slovakia s.r.o., Electrolux Domáce spot
rebièe SK, Seberíniho 1, 821 03 Bratislava

Electrolux Service, S:t Göransgatan 143,
S105 45 Stockholm

Tarlabaþý caddesi no : 35 Taksim
Istanbul

129090 Москва, Олимпийский
проспект, 16, БЦ „Олимпик“

Service and Spare Parts

If the event of your appliance requiring service, or if you wish to purchase spare
parts, please contact Service Force by telephoning:

0870 5 929 929

Your telephone call will be automatically routed to the Service Force Centre cov
ering your post code area.
For the address of your local Service Force Centre and further information about
Service Force, please visit the website at

www. serviceforce.co.uk

Before calling out an engineer, please ensure you have read the details under the
heading „What to do if...“

When you contact the Service Force Centre you will need to give the following
details:

1. Your name, address and post code.

2. Your telephone number.

3. Clear and concise details of the fault.

4. The model and serial number of the appliance (found on the rating plate)

5. The purchase date.

Please note that a valid purchase receipt or
guarantee documentation is required for in
guarantee service calls.

Customer Care

For general enquiries concerning your AEG
Electrolux appliance, or for further informa
tion on AEGElectrolux products please
contact our Customer Care Department by
letter or telephone at the address below or
visit our website at www.aeg.co.uk.

Customer Care Department
Major Appliances
AEGElectrolux
Domestic Appliances
Addington Way
Luton
Bedfordshire, LU4 9QQ
Tel: [phone] (*)

39Service and Spare Parts

For Customer Service in the Republic of
Ireland please contact us at the address be

low:
AEG/ Electrolux Group (Ire) Ltd
Long Mile Road/ Dublin 12
Republic of Ireland
Tel: [phone]
Email: [e-mail]

(*) Calls may be recorded for training purposes

www.electrolux.com

www.aeg-electrolux.co.uk

117 985 74/0-00-020507-01 Subject to change without notice