Page 1
Gas hob
INSTRINSTR
INSTR
INSTRINSTR
Please read this instruction booklet before using the appliance
UCTION BOOKLETUCTION BOOKLET
UCTION BOOKLET
UCTION BOOKLETUCTION BOOKLET
35678-9002
Mod. EGG 689
GB
Page 2
Important Safety Information
You MUST read these warnings carefully before installing or using the hob. If you need
assistance, contact our Customer Care Department on 08705 950950
During Operation
• This appliance has been designed for non professional
purpose in private houses only. It is meant to cook
edible foodstuff only and must not be used for any
other purposes.
• It is dangerous to alter the specification in any way.
• For hygiene and safety reasons, this appliance should
be kept clean at all times. A build-up of fats or other
foodstuff could result in a fire.
• Do not use this hob if it is in contact with water. Do
not operate the hob with wet hands.
• Never leave the hob unattended when cooking with
oil and fats.
• Unstable or misshapen pans should not be used on
the hob as unstable pans can cause an accident by
tipping or spillage.
• Never use plastic or aluminium foil dishes on the hob.
• Perishable food, plastic items and areosols may be
affected by heat and should not be stored above or
below the hob unit.
• Under no circumstances should you attempt to repair
the appliance yourself. Repairs carried out by
unexperienced persons may cause injury or serious
malfunctioning. Refer to your local Service Centre.
Always insist on genuine spare parts.
• Ensure that all control knobs are in the OFF position
when not in use.
• Should you connect any electrical tool to a plug near
this cooking appliance, ensure that electric cables
are not in contact with it and keep them far enough
from the heated parts of this appliance.
• If the appliance is out of order, disconnect it from the
electric supply.
Child Safety
! This appliance is not intended for use by children or
other persons whose physical, sensory or mental
capabilities or lack of experience and knowledge
prevents them from using the appliance safely without
supervision or instruction by a responsible person to
ensure that they can use the appliance safely.
• This appliance has been designed to be operated by
adults and children under supervision. Young children
must not be allowed to tamper with the controls or
play near or with the oven.
• Accessible parts of this appliance may become hot
when it is in use. Children should be kept away until
it has cooled.
• Children can also injure themselves by pulling pans
or pots off the hob.
About Installation, Cleaning
and Manteinance
! It is mandatory that all operations required for the
installation are carried out by a qualified or competent
person, in accordance with existing rules and
regulations in force in the country where the appliance
is used.
• Ensure a good ventilation around the appliance. A poor
air supply could cause lack of oxygen.
• Ensure that the gas and electrical supply complies
with the type stated on the identification label, placed
near the gas supply pipe.
• This appliance is not connected to a combustion
products evacuation device. It must be installed and
connected in accordance with current installation
regulations. Particular attention shall be given to the
relevant requirements regarding ventilation.
• The use of a gas cooking appliance results in the
production of heat and moisture in the room in which
it is installed. Ensure that the kitchen is well ventilated:
keep natural ventilation holes open or install a
mechanical ventilation device (mechanical extractor
hood).
• Prolonged intensive use of the appliance may call for
additional ventilation, for example opening of a window,
or more effective ventilation, for example increasing
the level of mechanical ventilation where present.
• Once you removed all packaging from the appliance,
ensure that it is not damaged and the electric cable
is in perfect conditions. Otherwise, contact your dealer
before proceeding with the installation.
• Disconnect the appliance from the electrical supply,
before carrying out any cleaning or manteinance work.
• This appliance cannot be cleaned with steam or with
a steam cleaning machine.
• The residual heat indicator comes on when the
cooking zone is switched on. Children should be kept
away until it switches off.
• Never use the ceramic hob as a working space. Do
not store things on the ceramic hob.
• Never use plastic or aluminium foil dishes on the
ceramic hob, as they could melt on the hob, thus
damaging it. Anyway,If anything of this nature
accidentally comes into contact with the ceramic
surface it must be scraped off immediately while stlll
hot and wiped away to avoid damage to the surface.
In the same way, remove sugar or food residues with
hich sugar content, which may have split from
saucepans by using a scraper for ceramic hobs.
• Unstable or misshapen pans should not be used on
the ceramic hob as unstable pans can cause an
accident by tipping or spillage.
2
Page 3
• The ceramic hob is shockproof, but not unbreakable!
Hard or pointed objects falling from a height can
damage the hob. If scratches or cracks are noticed,
disconnect the appliance from the electrical supply
to avoid the risk of electric shock and call you nearest
Service Force Centre.
Never use scratching sponges, abrasive products or
chemically powerful detergents. Use only cleaning
agents specific for ceramic hobs.
• The manufacturer disclaims any responsability should
all the safety measures not be carried out.
Contents
For the User
Important Safety Information 2
Description of the Hob 3
Operation 4
Maintenance and Cleaning 5
Service
! • Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried out by
unexperienced persons may cause injury or serious
malfunctioning. Refer to your local Service Centre.
Always insist on genuine spare parts.
Environmental Information
! After installation, please dispose of the packaging
with due regard to safety and the environment.
• When disposing of an old appliance, make it unusable,
by cutting off the cable.
• The symbol
indicates that this product may not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
and human health, which could otherwise be caused
by inappropriate waste handling of this product. For
more detailed information about recycling of this
product, please contact your local city office, your
household waste disposal service or the shop where
you purchased the product.
on the product or on its packaging
Something Not Working? 5
Guarantee/Customer Service 14
For the Installer
Instructions for the Installer 6
Important safety requirements 7
Installation 7
Building In 8
Electrical connections 9
Wiring Diagram 10
Fault Finding 10
Commissioning 12
Conversion from Natural Gas to LPG 13
Keep this instruction book for future reference
and ensure it is passed on to any new owner.
This appliance complies with the following
E.E.C. Directives:
* 73/23 - 90/683 (Low VoltageDirective);
* 93/68 (General Directives);
* 89/336 (Electromagnetical Compatibility
Directive);
* 90/396 (Gas Appliances),
and subsequent modifications
Guide to Use the instructions
The following symbols will be found in the text to guide
you throughout the Instructions:
Safety Instructions
Step by step instructions for an operation
"
Hints and Tips
Enviromental information
3
Page 4
Description of the Hob
1
1. Hob top
2. Rapid Burner
3. Semi-rapid Burner
4. Auxiliary Burner
5. Control knobs
3
3
5
4
2
Operation
Hob burners
"
To light a burner:
! push in the relevant control and turn it to maximum
position;
! then adjust the flame as required.
! If the burner does not ignite, turn the control knob to
zero, and try again.
In the absence of electricity, ignition can occur
without the electrical device; in this case approach
the burner with a flame, push the relevant knob
down and turn it anti-clockwise until it reaches
the"maximum" position.
When switching on the mains, after installation or
a power cut, it is quite normal for the spark
generator to be activated automatically.
If the control knobs become difficult to turn, please
contact your local Electrolux Service Centre.
If you use a saucepan which is smaller than the
recommended size, the flame will spread beyond
the bottom of the vessel, causing the handle to
overheat.
Take care when frying food in hot oil or fat, as
the overheated splashes could easily ignite.
As soon as a liquid starts boiling, turn down the
flame so that it will barely keep the liquid simmering.
Prolonged cooking with potstones, earthenware
pans or cast-iron plates is inadvisable. Also, do
not use aluminium foil to protect the top during
use.
Make sure pots do not protrude over the edges
of the cooktop and that they are centrally
positioned on the rings in order to obtain lower
gas consumption.
Do not place unstable or deformed pots on the
rings: they could tip over or spill their contents,
causing accidents.
Pots must not enter the control zone.
As soon as a liquid starts boiling, turn down the
flame so that it will barely keep the liquid
simmering.
Use only pans or pots with flat bottom.
To ensure maximum burner efficiency, you should only
use pots and pans with a flat bottom fitting the size of
the burner used (see table).
Burner minimum maximum
diameter diameter
Large (rapid) 160 mm. 240 mm.
Medium (semi-rapid) 120 mm. 220 mm.
Small (auxiliary) 80 mm. 160 mm.
4
Page 5
Maintenance and Cleaning
Before any maintenance or cleaning can be carried
out, you must DISCONNECT the hob from the
electricity supply.
The hob is best cleaned whilst it is still warm, as
spillage can be removed more easily than if it is
left to cool.
The Hob Top
Regularly wipe over the hob top and the aluminium frame
using a soft cloth well wrung out in warm water to which
a little washing up liquid has been added. Avoid the use
of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily soiled, it is
recommended that a cleaning product such as Hob Brite
or Bar Keepers Friend is used.
Pan Supports
The pan supports are dishwasher proof. If washing them
by hand, take care when drying them as the enamelling
process occasionally leaves rough edges.
If necessary, remove stubborn stains using a paste
cleaner. Never use steel wool pads or acids.
The Burners
The burner caps and crowns can be removed for cleaning.
Wash the burner caps and crowns using hot soapy water,
and remove marks with a mild paste cleaner. A well
moistened soap impregnated steel wool pad can be used
with caution, if the marks are particularly difficult to
remove.
After cleaning, be sure to wipe dry with a soft cloth.
Something Not Working?
If the hob is not working correctly, please carry out the following checks before contacting your local Service Force
Centre.
IMPORTANT:
a charge will be made even if the appliance is under guarantee.
SYMPTOM
# There is no spark when lighting the gas
# The gas ring burns unevenly
If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation,
SOLUTION
$ Check that the unit is plugged in and the electrical
supply is switched on
$ Check that the RCCB has not tripped (if fitted)
$ Check the mains fuse has not blown
$ Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
$ Check the main jet is not blocked and the burner
crown is clear of food particles.
$ Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
If after all these checks, your hob still does not operate
correctly, contact your local Service Force Centre.
Please note that it will be necessary to provide proof of
purchase for any in-guarantee service calls.
In-guarantee customers should ensure that the
above checks have been made as the engineer will
make a charge if the fault is not a mechanical or
electrical breakdown.
5
Page 6
Instructions for the Installer
Engineers technical data
Overall dimensions
Width: 580 mm.
Depth: 510 mm.
Cut out dimensions
Width: 550 mm.
Depth: 470 mm.
Supply connections
Gas:
R 1/2 inch (1/2 inch male) Rear right hand corner
Electric:
230-240V 50Hz supply, 3 core flexible cable with non
rewireable plug fitted with a 3 amp cartridge fuse.
GAS
TYPE OF
BURNER RAPID SEMI-RAPID AUXILIARY
CHARACTERISTICS
3
3
POSITION MAX MIN M AX MIN MAX MIN
NOMINAL THERMAL
POWER kW 2.9 0.75 1.9 0.45 1.0 0.33
(large) (medium) (small)
Ignition HT Spark
Spark Generator Ispra Control's BF 50046
230-240V 0.6 YA T 120
Spark Gap Fixed
Semi-rapid Burner
Heat Input 1.9 kW (6483 BTU/HR)
Rapid Burner
Heat Input 2.9 kW Natural Gas (9895 BTU/HR)
2.7 kW L.P.G. (9212 BTU/HR)
Auxiliary Burner
Heat Input 1.0 kW (3412 BTU/HR)
20 mbar
NATURAL GAS
VALUE = 37.78 MJ/m
LPG GAS
28-30/37 mbar
NOMINAL FLOW
RATE m
Ws - 50.7 MJ/ m
NOZZLE REFERENCE 119 Adjust. 96 Adjust. 70 Adjust.
NOMINAL THERMAL
POWER kW 2.7 0.75 1.9 0.45 1.0 0.33
NOMINAL FLOW
RATE g/h 195 46.8 137 32.4 72 23.8
NOZZLE REFERENCE 86 4 0 71 3 2 50 28
VALUE = 49.92 MJ/Kg
3
/h 0.276 0.062 0.181 0.043 0.095 0.031
1/100 mm
1/100 mm
Burner Dia. Tap By-pass
1/100 mm
Auxiliary 28
Semi-rapid 32
Rapid 42
Aeration adjustment none
APPLIANCE CLASS: 3
APPLIANCE CATEGORY: II2H3+
APPLIANCE GAS SUPPLY: Natural gas G20 / 20mbar
6
Page 7
Important safety requirements
This hob must be installed in accordance with the Gas Safety (Installation and
Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current
Edition).
Detailed recommendations are contained in the following British Standards Codes
Of Practice: B.S. 6172/ B.S. 5440, Part 2 and B.S. 6891 Current Editions.
The hob should not be installed in a bed sitting room with a volume of less than
3
20 m
. If it is installed in a room of volume less than 5 m3 an air vent of effective
area of 110 cm
3
10 m
an air vent of effective area of 50 cm2 is required, while if the volume
exceeds 11 m
However, if the room has a door which opens directly to the outside no air vent is
required even if the volume is between 5 m
If there are other fuel burning appliances in the same room, B.S. 5440 Part 2
Current Edition, should be consulted to determine the requisite air vent
requirements.
2
is required. If it is installed in a room of volume between 5 m3 and
3
no air vent is required.
3
and 11 m3.
Location
The hob may be located in a kitchen, a kitchen/diner or bed sitting room, but not
in a bathroom, shower room or garage.
Before making the cut out in the worktop ensure that the edges of the hob that
are to be near either a side or rear wall have a minimum distance of 55 mm.
between the edge of the hob and the wall.
The minimum distance combustible material can be fitted above the hob is 400
mm. If it is fitted below 400 mm. a space of 50 mm. must be allowed from the
edges of the hob.
The minimum distance combustible material can be fitted directly above the hob
is 700 mm. A minimum distance of 100 mm. must be left between the side edges
of the hob and any adjacent cabinets or walls.
FITTING THE GAS HOB
WITHOUT A COOKER HOOD ABOVE
FITTING THE GAS HOB
WITH A COOKER HOOD ABOVE
FO 0812
Installation
IMPORTANT
This hob must be installed by qualified
personnel to the relevant British Standards.
Any gas installation must be carried out by a
registered CORGI installer.
The manufacturer will not accept liability, should
the above instructions or any of the other safety
instructions incorporated in this book be
ignored.
Gas Connection
Connection to the gas supply should be with either rigid
or semi-rigid pipe, i.e. steel or copper.
The connection should be suitable for connecting to R
1/2” (1/2 BSP male thread).
When the final connection has been made, it is essential
that a thorough leak test is carried out on the hob and
installation. Ensure that the main connection pipe does
not exert any strain on the hob.
It is important to install the elbow correctly, with
the shoulder on the end of the thread, fitted to the
hob connecting pipe.
Failure to ensure the correct assembly will cause
leakage of gas.
FO 0813
WHEN THE HOB IS FIRST INSTALLED
Once the hob has been installed, it is important
to remove any protective materials, which were
put on in the factory.
On the end of the shaft, which includes the G 1/2"
threaded elbow, adjustment is fixed so that the washer
is fitted between the components as shown in the
diagram. Screw the parts together without using excessive
force.
FO 0814
A) End of shaft with nut
B) Washer
FO 0264
C) Elbow
7
Page 8
Cut Out Size
The dimensions of the cut-out are given in the diagram.
1
470
FO 2098
30
550
Building In
Building over a cupboard or
drawer
If the hob is to be installed above a cupboard or drawer it
will be necessary to fit a heat resistant board below the
base of the hob on the underside of the work surface.
It is also recommended to carry out the electrical
connection to the hob as shown in diagrams 1 and 2.
Building over a kitchen unit with
door
Proper arrangements must be taken in designing the
furniture unit, in order to avoid any contact with the bottom
of the hob which can be heated when it is operated. The
recommended solution is shown in diagram 3.
The panel fitted under the hob ("a") should be easily
removable to allow easy access if technical assistance
is needed. The space behind the kitchen unit ("b") can
be used for connections.
2
FO 0764
Dimensions are given in mm.
FO 0763
3
FO 1013
Fitting the hob to the worktop
Before fitting the hob into the cut out, an adhesive seal
must be fitted to the underside outside edge of the hob.
It is essential that no gaps are left in this seal in order to
prevent spillage near the hob seeping into the cabinet
below.
1) Remove the pan supports, the burners caps and
"
crowns and turn the hob upside down, taking care
the ignition candles are not damaged in this
operation.
2) Place the relevant sealing all around the glass
top edge, taking care that the sealings meet
without overlapping (Fig. 4).
3) Place the hob in the cut out, taking care of its
centring.
4) Fix the hob with the relevant screws (Fig. 5).
8
FO 2108
a) Sealing gasket
4
5
A
Page 9
Electrical connections
Any electrical work required to install this hob
should be carried out by a qualified electrician or
competent person, in accordance with the current
regulations.
THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability should these
safety measures not be observed.
This hob is designed to be connected to a 230-240V
50Hz AC electrical supply.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the hob rating
plate. The rating plate is located on the bottom of the
hob. A copy is attached on the back cover of this book.
The hob is supplied with a 3 core flexible supply cord
incorporating a 3amp plug fitted. In the event of having to
change the fuse, a 3amp ASTA approved (BS 1362) fuse
must be used.
Should the plug need to be replaced for any reason, the
wires in the mains lead are coloured in accordance with
the following code:
Green and Yellow - Earth
Blue - Neutral
Brown - Live
— Connect the green and yellow (earth) wire to
"
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure over
the outer sheath.
the terminal in the plug which is marked with
the letter 'E' or the earth symbol
green and yellow.
— Connect the blue (neutral) wire to the terminal
in the plug which is marked with the letter 'N'
or coloured black.
— Connect the brown (live) wire to the terminal in
the plug which is marked with the letter 'L' or
coloured red.
A cut off plug inserted into a 13 amp socket is
a serious safety (shock) hazard. Ensure that
the cut off plug is disposed of safely.
or coloured
Permanent Connection
In the case of a permanent connection, it is necessary
that you install a double pole switch between the hob
and the electricity supply (mains), with a minimum gap
of 3 mm. between the switch contacts and of a type
suitable for the required load in compliance with the
current electric regulations.
The switch must not break the yellow and green earth
cable at any point.
Ensure that the hob supply cord does not
come into contact with surfaces with
temperatures higher than 50 deg. C.
Supply cable replacement
The cable used to connect the hob to the electrical supply
must comply to the specifications given below.
Min. size Cable/flex Cable / flex type Fuse
0.75 mm
2
FO 0390
H05 V2V2-F (T90) 3 A
9
Page 10
N
Wiring Diagram
( )
FUSE
( )
E
N
L
220
240
0
2
1
2
3
4
Brown
L
1
Fault Finding
Preliminary Electrical Systems
Check
Blue
Blue
Brown
Green
Yellow
Green
Yellow
START
Isolate appliance
and carry out:
A: Earth Continuity
check.
NO
YES
A. IGNITOR SWITCH
B. IGNITOR UNIT
PLUG (with cover
removed)
Earth Wire
Green/Yellow
Neutral Wire
Blue
Carry out:
C: Polarity check.
Carry out:
D: Resistance to
Earth check.
SOCKET
(face view)
Electricity supply
should now be
satisfactory.
Has inlet fuse blown?
NO YES
Inlet wiring
faulty.
Rectify any
fault.
Isolate appliance and
carry out:
B: Insulation check.
Rectify any fault
including replacing
fuses as necessary.
A. EARTH CONTINUITY CHECK - Appliance must be
electrically disconnected - meter set on Ω (Ohms) x
1 scale and adjust zero if necessary.
a) Test leads from any appliance earth point to earth
pin on plug. Resistance should be less than 0.1
Ω (Ohm), check all earth wires for continuity and
all contacts are clean and tight.
B. INSULATION CHECK - Appliance electrically
disconnected, all switches ON.
a) meter set on Ω (Ohms) x 1 scale.
Test leads from L to N in appliance terminal block.
If meter reads «0» then there is a short circuit.
b) meter set on Ω (Ohm) x 100 scale.
Repeat test with leads from L to E. If meter reads
less than ∞ (infinity) there is a fault.
NOTE - Should it be found that the fuse has failed
but no fault is indicated - a detailed continuity check
(i.e. by disconnecting and checking each
component) is required to trace the faulty component.
It is possible that a fault could occur as a result of
local burning/arcing but no fault could be found under
test. However a detailed visual inspection should
reveal evidence of burning around the fault.
10
Page 11
Ignition System / Gas Ignition
Ignitor does not spark
NO
Check plug top fuse and
replace if necessary
Check polarity and earth
continuity of supply point
Check earth continuity
of appliance
Check continuity from 'N' on the
mains connector block and "O" on
the ignitor unit
YES
Check continuity from the tip of
each electrode to the terminals 1
to 4 on the ignitor unit
Check gas supply at
burner
Light burner manually
Check by pass simmer
adjusted
Check position of the
electrode
Check fitting of burners
Check continuity from 'L' on the
mains connector block and the
taps ignition switches
Check continuity from ignition
switches connector to ignitor unit
Check for breaks in the insulation
of the HT leads
Change the taps
ignition switches
Change the ignitor unit
11
Page 12
Commissioning
When the hob has been fully installed it will be necessary
to check the minimum flame setting. To do this, follow
the procedure below.
- Turn the gas tap to the MAX position and ignite.
- Set the gas tap to the MIN flame position then turn
the control knob from MIN to MAX several times. If
the flame is unstable or is extinguished follow the
procedure below.
Procedure:
Re-ignite the burner and set to MIN.
"
Remove the control knob.
To adjust, use a thin bladed screwdriver and turn
the adjustment screw (see diagram) until the flame
is steady and does not extinguish, when the knob
is turned from MIN to MAX. Repeat this procedure
for all burners.
Minimum adjustment screw
Pressure Testing
Remove left hand pan support and front left burner
"
cap and crown.
Fit manometer tube over the injector.
Turn on the burner gas supply and ignite another
burner.
The pressure reading should be nominally 20mbar
and must be between 17 mbar and 25mbar.
Turn off the burner supplies.
12
Page 13
Conversion from Natural Gas to
LPG
It is important to note that this model is designed for
use with natural gas but can be converted for use with
butane or propane gas providing the correct injectors
are fitted. The gas rate is adjusted to suit.
Method
• Ensure that the gas taps are in the 'OFF' position
• Isolate the hob from the electrical supply
• Remove all pan supports, burner caps, rings, crowns
and control knobs.
• With the aid of a 7mm box spanner the burner injectors
can then be unscrewed and replaced by the
appropriate LPG injectors.
To adjust the gas rate
With the aid of a thin bladed screwdriver completely
tighten down the by pass adjustment screw. Upon
completion affix the replacement rating plate on the under
side of the hob.
IMPORTANT
The replacement/conversion of the gas hob should only
be undertaken by a competent person.
13
Page 14
Guarantee/Customer Service
Standard guarantee conditions
We, Electrolux, undertake that if within 12 months of the
date of the purchase this Electrolux appliance or any
part thereof is proved to be defective by reason only of
faulty workmanship or materials, we will, at our option
repair or replace the same FREE OF CHARGE for labour,
materials or carriage on condition that:
· The appliance has been correctly installed and
used only on the electricity or gas supply stated
on the rating plate.
· The appliance has been used for normal domestic
purposes only, and in accordance with the
manufacturer’s instructions.
· The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any
person not authorised by us.
· Electrolux Service Force Centre must undertake
all service work under this guarantee.
· Any appliance or defective part replaced shall
become the Company’s property.
· This guarantee is in addition to your statutory and
other legal rights.
Exclusions
· Damage or calls resulting from transportation,
improper use or neg-lect, the replacement of any
light bulbs or removable parts of glass or plastic.
· Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliances
outside the United Kingdom.
· Appliances found to be in use within a commercial
environment, plus those which are subject to rental
agreements.
· Products of Electrolux manufacturer that are not
marketed by Electrolux.
Service and Spare Parts
In the event of your appliance requiring service, or if you
wish to purchase spare parts, please contact your local
Service Force Centre by telephoning
0870 5 929 929
Your telephone call will be automatically routed to the
Service Force Centre covering your postcode area.
For the address of your local Service Force Centre and
further information about Service Force, please visit the
website at
www.serviceforce.co.uk
Before calling out an engineer, please ensure you have
read the details under the heading “Something not
working”.
When you contact the Service Force Centre you will need
to give the following details:
1.Your name, address and postcode.
2.Your telephone number.
3. Clear concise details of the fault.
4. The model and Serial number of the appliance (found
on the rating plate).
5.The purchase date.
Please note a valid purchase receipt or guarantee
documentation is required for in guarantee service calls.
Customer Care
For general enquiries concerning your Electrolux
appliance, or for further information on Electrolux products
please contact our Customer Care Department by letter
or telephone at the address below or visit our website at
www.electrolux.co.uk
Customer Care Department
Electrolux Major Appliances
Addington Way
Luton
Bedfordshire, LU4 9QQ
Tel: 08705 350 350 (*)
(*) Calls may be recorded for training purposes
14
Page 15
European Guarantee
This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period
specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the
countries listed below the appliance guarantee will move with you subject to the following qualifications:
• The appliance guarantee starts from the date you first purchased the appliance which will be evidenced by
production of a valid purchase document issued by the seller of the appliance.
• The appliance guarantee is for the same period and to the same extent for labour and parts as exists in your new
country of residence for this particular model or range of appliances.
• The appliance guarantee is personal to the original purchaser of the appliance and cannot be transferred to
another user.
• The appliance is installed and used in accordance with instructions issued by Electrolux and is only used within
the home, i.e. is not used for commercial purposes.
• The appliance is installed in accordance with all relevant regulations in force within your new country of residence.
The provisions of this European Guarantee do not affect any of the rights granted to you by law.
15
Page 16
Grafiche MDM - Forlì
11/06
Loading...