Thank you for choosing a fi rst class
product from Electrolux, which
hopefully will provide you with lots of
pleasure in the future. The Electrolux
ambition is to offer a wide variety of
quality products that make your life
more comfortable. You fi nd some
examples on the cover in this manual.
Please take a few minutes to study this
manual so that you can take advantage
of the benefi ts of your new machine.
We promise that it will provide a
superior User Experience delivering
Ease-of-Mind.
Good luck!
electrolux 3
Guide to use the instruction book
The following Symbols will be found in the text to guide you through the instruction book
Safety instructions Step by step instructions
Page 4
4 electrolux IMPORTANT SAFETY INFORMATION
IMPORTANT SAFETY INFORMATION
These warnings are provided in the interests of your safety. Ensure that you
understand them all before installing or using this appliance. Your safety is of
paramount importance. If you are unsure about any of the meanings of these
EN
warnings contact the Customer Care Department.
Installation
• Any installation work must be undertaken
by a qualifi ed electrician or a competent
person.
• This hood must be installed in accordance
with the installation instructions and all
measurements must be adhered to.
• If the cooker hood is installed for use
above a gas appliance then the provision
for ventilation must be in accordance
with the Gas Safety Codes of Practice
BS.6172, BS.5440 and BS.6891 (Natural
Gas) and BS.5482 (LP Gas) 1994, the
Gas Safety (Installation & Use) Regulations,
the Building Regulations issued by
the Department of the Environment,
the Building standards (Scotland)
(Consolidated) Regulations issued by the
Scottish Development Department.
• The fan motor of this cooker hood
incorporates a cut-out device which will
operate if the cooker hood is installed
below the minimum height recommended
under section ‘Clearance Height’, or if the
motor becomes overheated. If the cutout device is activated, switch off the fan
motor and allow the cooker hood to cool.
The cut-out device will reset itself when
the fan motor has cooled signifi cantly.
• It is dangerous to alter the specifi cations
or modify this product in any way.
• When installed between adjoining wall
cabinets the wall cabinets must not
overhang the hob.
• If the room where the hood is to be used
contains a fuel burning appliance such as
a central heating boiler then its fl ue must
be of the room sealed or balanced fl ue
type.
• If other types of fl ue or appliances are fi tted ensure that there is an adequate
supply of air to the room.
• The ducting system for this appliance
• Do not install above a cooker with a high
Child Safety
• This appliance is designed to be operated
During Use
• This product is for domestic use only.
• Never leave frying pans unattended during
• Never do flambé cooking under this
• Do not leave naked fl ames under the
• This cooker hood is designed to extract
Maintenance and Service
• This appliance can be a hazard if the
• Under no circumstances should you
must not be connected to any existing
ventilation system which is being used
for any other purpose.
level grill.
by adults. Children should not be allowed
to tamper with the controls or play with
the appliance.
use as over-heated fats and oils might
catch fi re.
cooker hood.
hood.
unpleasant odours from the kitchen, it will
not extract steam.
synthetic paper and charcoal fi lters are
not replaced as recommended.
attempt to repair the appliance yourself.
Repairs carried out by inexperienced
persons may cause injury or more
serious malfunction. Refer to your local
Electrolux Service Force Centre. Always
insist on genuine spare parts.
Page 5
YOUR APPLIANCE AND OPERATING INSTRUCTIONSelectrolux 5
YOUR APPLIANCE
OPERATING INSTRUCTIONS
The cooker hood is designed to extract
unpleasant odours from the kitchen, it
will not extract steam.
To obtain the best performance it is
advisable to switch on the hood a few
minutes before you start cooking and
leave it running for approximately 15
minutes after fi nishing.
Cooker Hood Controls
The cooker hood functions are
controlled by slide switches, located
centrally in the front edge of the metal
grille panel.
EFG 50021
L. Light ON/OFF control
0 - Off
1 - On
V. Fan Speed Control
Position 0 - Off
Position 1 - Low
Position 2 - Normal
Position 3 - Boost
EN
EFG 50021
Page 6
6 electrolux
EFG 50022
L. Light ON/OFF control
0 - Off
1 - On
M.Motor ON/OFF control
EN
0 - Off
1 - On
V. Fan Speed Control
Position 1 - Low
Position 2 - Normal
Position 3 - Boost
To Operate
Select the required functions.
The appliance can be installed to
recirculate or extract contaminated air.
The cooker hood is more effective when
used in the extraction mode.
Extraction
In the extraction mode the contaminated
air enters the cooker hood, passes
through the grease fi lter and out through
the ducting to the atmosphere.
Recirculation
In the recirculation mode contaminated
air is passed through the charcoal
fi lters to be purifi ed and recirculated
into the kitchen through a recirculation
grille. Ensure the charcoal fi lters are in
position.
When the ducting mode is selected
the charcoal fi lters are not required.
Never do fl ambé cooking under this
cooker hood.
Never leave frying pans unattended
during use as over-heated fats and
oils can catch fi re.
Do not leave naked fl ames under the
cooker hood.
Ensure heating areas on your hob
are covered with pots and pans
when using the hob and cooker hood
simultaneously.
EFG 50022
Page 7
MAINTENANCE AND CLEANING electrolux 7
MAINTENANCE AND CLEANING
Before carrying out any maintenance
or cleaning isolate the cooker hood
from the mains supply.
The cooker hood must be kept clean,
as a build up of grease or fat can be
a fi re hazard.
The external surfaces of the hood
should be cleaned regularly. Wipe the
cooker hood frequently with warm
soapy water using a mild detergent. Dry
thoroughly after cleaning.
Always wear protective gloves when
cleaning the hood.
Never use scouring pads or abrasive
cleaners.
Never use excessive amounts of wa-
ter when cleaning particularly around
the control panel.
Charcoal Filter
The charcoal fi lters absorb the odours
from cooking. They will slowly become
saturated and gradually less effective.
The charcoal fi lters cannot be cleaned,
we recommend they are replaced every
3-6 months or more often if the hood is
used for more than 3 hours per day.
EN
To Remove/Replace the
Charcoal Filters
1.Remove the lower grille, supporting
the grille with one hand and draw
down on the two grey handles
(located on each side of the grille).
2.The charcoal fi lters are left and right
handed and should be fi tted one at
a time.
3.Insert one end of the fi lter into the
slots in the fan housing then lower the
other end until the tab engages the
slot in the casing.
Page 8
8 electrolux
Synthetic Grease Filter - EFG 50021
The synthetic grease fi lter cannot be
cleaned.
It cannot be washed.
EN
To Replace the Synthetic
Grease Filter
1.Remove the lower grille.
2.Push the wire retaining clips to the
side and remove.
3.Clean the metal grille and clips before
replacing the paper grease fi lter.
The clips have sharp points, handle
with care and keep away from children.
This appliance is a possible fi re ha-
zard if the grease and charcoal fi lters
are not replaced as recommended.
Metal Grease Filters - EFG 50022
The metal grease fi lters can be
machine washed in a dishwasher, or
hand washed in hot water and a mild
detergent or liquid soap.
To Remove/Replace the Metal
Filters
1.Press against the metal actuator to
release the spring catch.
2.Drop the front edge of the cassette
down as illustrated opposite and lift
the back edge out of the rear guide.
3.To refi t insert the back edge of the
cassette into the rear guide and push
up the front edge until the spring
catch engages.
This appliance is a possible fi re
hazard if the grease fi lters are not
cleaned reguarly and the charcoal
fi lters replaced as recommended.
Page 9
Changing the Light Bulb
If a lamp fails to function at any time
fi rst check that it is fully screwed into
the holder. To tighten the lamps turn
clockwise, but ensure not to over
tighten them and break the lens.
When changing the lamps an identical
replacement must be fi tted to ensure
the safe working of the cooker hood.
The replacement lamp is specifi ed 220-
240 volt 40 watt clear cylindrical shape
lens with a small Edison (E14) screw
thread.
Replacement fi lters and lamps bulbs
can be obtained from your local Service
Force Centre.
electrolux 9
EN
Page 10
10 electrolux SOMETHING NOT WORKING
SOMETHING NOT WORKING
If, having followed these instructions carefully, your cooker hood fails to work properly
please carry out the following checks.
EN
Symptom
The cooker hood will not start
The cooker hood is not working
effectively
The cooker hood has switched off
during operation
If after all these checks, the fault persists,
contact your local Service Force Centre,
quoting the model and serial number.
Please note that it will be necessary to provide proof of purchase for any in-guarantee
service calls.
Solution
• Check the hood is connected to the
electricity supply.
• Make sure the switch is in the ‘ON’ posi
tion.
• The fan speed is set high enough for the
task
• The grease fi lter is clean.
• The kitchen is adequately vented to allow
the entry of fresh air.
• If set up for recirculation, check that the
charcoal fi lter is still effective.
• If set up for extraction, check that the
ducting and outlets are not blocked.
• The safety cut-out device has been trip
ped.
• Tum off the hob and then wait for the
device to reset.
In-guarantee customers should ensure
that the above checks have been made
as the engineer will make a charge if
the fault is not a mechanical or electrical breakdown.
Page 11
GUARANTEE/CUSTOMER SERVICE electrolux 11
GUARANTEE/CUSTOMER SERVICE
Standard guarantee conditions
We, Electrolux, undertake that if within
12 months of the date of the purchase
this Electrolux appliance or any part
thereof is proved to be defective by
reason only of faulty workmanship or
materials, we will, at our option repair
or replace the same FREE OF CHARGE
for labour, materials or carriage on
condition that:
• The appliance has been correctly
installed and used only on the
electricity supply stated on the rating
plate.
• The appliance has been used for
normal domestic purposes only, and
in accordance with the manufacturer’s
instructions.
• The appliance has not been serviced,
maintained, repaired, taken apart or
tampered with by any person not
authorised by us.
• Electrolux Service Force Centre must
undertake all service work under this
guarantee
• Any appliance or defective part
replaced shall become the Company’s
property.
• This guarantee is in addition to your
statutory and other legal rights.
Exclusions
• Damage or calls resulting from
transportation, improper use or
neglect, the replacement of any light
bulbs or removable parts of glass or
plastic.
• Costs incurred for calls to put right
an appliance which is improperly
installed or calls to appliances outside
the United Kingdom.
• Appliances found to be in use within
a commercial environment, plus
those which are subject to rental
agreements.
• Products of Electrolux manufacturer
that are not marketed by Electrolux
Service and Spare Parts
In the event of your appliance requiring
service, or if you wish to purchase spare
parts, please contact your local Service
Force Centre by telephoning
0870 5 929 929
Your telephone call will be automatically
routed to the Service Force Centre
covering your postcode area.
For the address of your local Service
Force Centre and further information
about Service Force, please visit the
website at
www.serviceforce.co.uk
Before calling out an engineer, please
ensure you have read the details under
the heading “Something not working”
When you contact the Service Force
Centre you will need to give the
following details:
1.Your name, address and postcode.
2.Your telephone number.
3.Clear concise details of the fault.
4.The model and Serial number of the
appliance (found on the rating plate).
5.The purchase date.
Please note a valid purchase receipt or
guarantee documentation is required for
in guarantee service calls.
EN
Page 12
12 electrolux GUARANTEE CONDITIONS
GUARANTEE CONDITIONS
Customer Care
For general enquiries concerning your
Electrolux appliance, or for further
information on Electrolux products
EN
please contact our Customer Care
Department by letter or telephone at
the address below or visit our website
at www.electrolux.co.uk
Customer Care Department
Electrolux Major Appliances
Addington Way
Luton
Bedfordshire, LU4 9QQ
Tel: 08705 950 950 (*)
(*) Calls may be recorded for training
purposes
European Guarantee
This appliance is guaranteed by
Electrolux in each of the countries
listed at the back of this user manual,
for the period specifi ed in the appliance
guarantee or otherwise by law. If you
move from one of these countries to
another of the countries listed below the
appliance guarantee will move with you
subject to the following qualifi cations:-
• The appliance guarantee starts from
the date you fi rst purchased the
appliance which will be evidenced
by production of a valid purchase
document issued by the seller of the
appliance.
• The appliance guarantee is for the
same period and to the same extent
for labour and parts as exists in
your new country of residence for
this particular model or range of
appliances.
• The appliance guarantee is personal
to the original purchaser of the
appliance and cannot be transferred
to another user.
• The appliance is installed and used
in accordance with instructions
issued by Electrolux and is only used
within the home, i.e. is not used for
commercial purposes.
• The appliance is installed in
accordance with all relevant
regulations in force within your new
country of residence.
The provisions of this European Guarantee
do not affect any of the rights granted to you
by law.
Page 13
electrolux 13
www.electrolux.com
à
Albania+35 5 4 261 450Rr. Pjeter Bogdani Nr. 7 Tirane
Belgique/België/Belgien+32 2 363 04 44Bergensesteenweg 719, 1502 Lembeek
Česká republika+420 2 61 12 61 12Budějovická 3, Praha 4, 140 21
Danmark+45 70 11 74 00Sjællandsgade 2, 7000 Fredericia
Deutschland+49 180 32 26 622Muggenhofer Str. 135, 90429 Nürnberg
Eesti+37 2 66 50 030Mustamäe tee 24, 10621 Tallinn
España+34 902 11 63 88Carretera M-300, Km. 29,900 Alcalá de Henares Madrid
France www.electrolux.fr
Great Britain+44 8705 929 929Addington Way, Luton, Bedfordshire LU4 9QQ
Hellas+30 23 10 56 19 704, Limnou Str., 54627 Thessaloniki
Hrvatska+385 1 63 23 338Slavonska avenija 3, 10000 Zagreb
Ireland+353 1 40 90 753Long Mile Road Dublin 12
Italia+39 (0) 434 558500C.so Lino Zanussi, 26 - 33080 Porcia (PN)
Latvija+37 17 84 59 34Kr. Barona iela 130/2, LV-1012, Riga
Lietuva+370 5 2780609Verkių 29, LT-09108 Vilnius
Luxembourg+35 2 42 43 13 01Rue de Bitbourg, 7, L-1273 Hamm
Magyarország+36 1 252 1773H-1142 Budapest XIV, Erzsébet királyné útja 87
Nederland+31 17 24 68 300Vennootsweg 1, 2404 CG - Alphen aan den Rijn
Norge+47 81 5 30 222Risløkkvn. 2 , 0508 Oslo
Österreich +43 18 66 400Herziggasse 9, 1230 Wien
Polska+48 22 43 47 300ul. Kolejowa 5/7, Warsaw
Electrolux Service, S:t Göransgatan 143, S-105 45
Stockholm
129090 Москва, Олимпийскийпроспект, 16, БЦ
“Олимпик”
EN
Page 14
14 electrolux INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
It is dangerous to alter the specifi cations or attempt to modify this product in any way.
Technical Information
EN
DIMENSIONS HEIGHT: 196mm
WIDTH: 522mm
DEPTH: 284mm
DUCTING OUTLET: 120mm
WEIGHT GROSS: EFG 50021 4,2 kg - EFG 50022 4.4 kgNET: EFG 50021 5,2 kg - EFG 50022 5.4 kg
ELECTRICAL SUPPLY: Voltage (50Hz) 220-240V
POWER CONSUMPTION: EFG 50021 195W - EFG 50022 215W
FAN MOTOR: EFG 50021 115W - EFG 50022 135W
LAMP: 2 x 40 W 80W
SUITABLE FOR INSTALLATION
ABOVE: ELECTRIC HOB: 7KW (max)
GAS HOB: 10KW (max)
SLOT-IN GAS COOKER 13.5KW (max)
SLOT-IN ELECTRIC COOKER 12.4KW (max)
Note: CE Marking certifi es that this appliance complies with the requirements
laid down in EEC directive 89:336. (Electromagnetic compatibility) and subsequent modifi cations and Low Voltage directive 72/23/E.
The symbol
shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product,
please contact your local city offi ce, your household waste disposal service or the shop where you purchased the product.
on the product or on its packaging indicates that this product may not be treated as household waste. Instead it
Page 15
ELECTRICAL CONNECTIONSelectrolux 15
ELECTRICAL CONNECTIONS
DOUBLE INSULATED DO NOT EARTH
Electrical Requirements
Any permanent electrical installation
must comply with the latest I.E.E.
Regulations and local Electricity Board
regulations. For your own safety this
should be undertaken by a qualifi ed
electrician e.g. your local Electricity
Board, or a contractor who is on the
roll of the National Inspection Council
for Electrical Installation Contracting
(NICEIC).
Electrical Connection
Before connecting to the mains
supply ensure that the mains voltage
corresponds to the voltage on the rating
plate inside the cooker hood.
This appliance is fi tted with a 2 core
mains cable and must be permanently
connected to the electricity supply
via a double-pole switch having
3mm minimum contact gap on each
pole. A Switched Fuse Connection
Unit to BS1363 Part 4, fi tted with
a 3 Amp fuse, is a recommended
mains supply connection accessory
to ensure compliance with the Safety
Requirements applicable to fi xed wiring
instructions.
This appliance conforms to BS 800:
1988 and EEC Directive No. 78 308
regarding suppression of ra dio and
television interference.
EN
Page 16
16 electrolux INSTALLING THE COOKER HOOD
INSTALLING THE COOKER HOOD
Please ensure that when the
appliance is installed it is easily
accessible to an engineer in the
EN
event of a breakdown.
All installations must comply with the
local authorities requirements for the
discharge of exhaust air.
Incorrect installation may affect the
safety of this cooker hood.
Installation Requirements
Before fi tting the hood beneath
any type of canopy or wall cabinet,
ensure that the housing is fi rmly fi xed
to the wall in accordance with the
manufacturer’s instructions.
If it is necessary to fi x the housing for
the canopy to a hollow construction
plaster or partition board structure then
it should be suffi ciently reinforced to
be quite rigid in the area of the cabinet
housing fi xings.
Clearance Height
The cooker hood is designed to be
fi tted over a cooking appliance at the
clearance heights stated, providing
the maximum output of the appliance
beneath does not exceed the maximums
quoted in the Technical Specifi cations.
If the output of the appliance below the
cooker hood exceeds the maximum
outputs quoted, please refer to the
cooker manufacturer’s installation
instructions.
Clearance Height
A clearance height of 650mm (25 1/2 ”)
is required when installed above a builtin electric hob, or 700mm (27 1/2 ”)
when installed above a built-in gas hob.
A clearance height of 685mm (27”)
is required when installed above a
slot-in electric cooker, or 787mm (30
1/2 ”) when installed above a slot-in gas
cooker.
Ducting
The ducting must be fi re retardant
125mm (5ins) in diameter and the length
should be no more than:
3 metres with one 90° bend
2 metres with two 90° bends
Bends of more than 90° will reduce the
effi ciency of the hood and reduce the
airfl ow.
Page 17
When installed between adjoining wall
cabinets, the wall cabinets must not
overhang the hob and the distance
between the underside of the cabinet
and the worktop must be 450mm. If
the height of the wall cabinet is less
than 450mm, a gap of 50mm must be
maintained either side of the hob.
electrolux 17
EN
Hob
This cooker hood must not be instal-
led above a cooking appliance with a
high level grill.
Unpacking
The fi ttings supplied to install this cooker
hood can be found with the instruction
book inside the packaging:
120 - 125 mm ducting collar
Fitting the Cooker Hood
into the Housing/Canopy
The hood is fi xed to the housing using
the screw holes located around the
base of the casing. Access to the screw
holes will require the removal of the
metal grille panel.
Positioning the Cooker Hood
Measure the underside of the canopy or
kitchen cabinet to mark the position for
the cut-out. The cut-out measurement
should be:
- 497mm (19 5/8”) wide
- 259mm (10 1/4”) deep
A: Built-in Electric Hob: 650mm clearance
B: Built-in Gas hob: 700mm clearance
C: Slot-in Electric Cooker: 685mm clearance
D: Slot-in Gas Cooker: 787mm clearance
Check the position of the hole is
correct with the measurements
above before making the cut-out.
Page 18
18 electrolux
The hood is fi xed using the holes
located in the rim around the base of
the casing visible when the inlet grille is
in the open position.
Support the grille panel with one hand
EN
and draw down on the two grey handles
(A) which are located on each side of
the grille with the other hand.
Raise the hood into the cut out and mark
the positions for the fi xing screws. Pilot
drill the fi xing holes and fi t the hood.
Venting
The hood is more effective when used
in the extraction mode (ducted to the
outside). Venting kits maybe purchased
through your retailer or DIY store, and
must be ducted to an outside vent of
125mm (5”) minimum.
The ducting used must be manufac-
tured from fi re retardant material.
When the hood is ducted externally the
charcoal fi lters must be removed.
Recirculation
If you are using the hood for recirculating,
ensure the charcoal fi lters are in position
following the instructions below.
Inserting the Charcoal
Filters
1.Remove the grille panel, support the
grille with one hand and draw down
on the two grey handles (located at
each side of the grille).
2.The charcoal fi lters are handed and
should be fi tted one at a time.
3.Insert one end of the fi lter into the
slots in the fan housing, then lower
the other and until the tab engages
the slot in the casing.
Page 19
Extraction
The charcoal fi lters are not required in
this mode and should be removed. To
do this reverse the procedure described
in Inserting the ‘Charcoal Filters’.
Ducting
The ducting used must be fi re retardant
125mm (5”) in diameter. If possible
duct through the wall at the rear of the
canopy or wall cabinet. For the best
per for man ce use the shortest possible
duct run and the minimum number
of bends. Where fl exible ducting is fi tted it should not be turned through
very tight bends as this may impair
the performance of the hood. It is
recommended a maximum length of
3m, to be installed, to be reduced
1m for each 90° bend installed in the
ducting run. If the distance is greater
than 3m the effi ciency of the hood could
be impaired.
A ducting collar of 120-125 mm (5”) is
supplied for attaching to ducting if you
are using the appliance in the extraction
mode.
electrolux 19
EN
If the room where the cooker hood
is to be used contains a fuel burning
appliance such as a central heating
boiler, then its fl ue must be of the
room sealed or balanced fl ue type.
If other types of fl ue or appliances are
fi tted ensure that there is an adequate supply of air to the room.
The cooker hood ducting (extraction
version) must never be connected
to central heating fl ues, radiators or
water heaters etc.
Page 20
electrolux 20
Page 21
electrolux 21
Page 22
electrolux 22
Page 23
Page 24
www.electrolux.com
436003735_01 - 070314
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.