AEG EFC9563, EFC9583, EFC9561 User Manual
This manual explains the proper use of your new canopy
100mm
520mm
407mm
O163mm
850mm
1275mm
(maximum)
331mm
698mm
100mm
500mm
391mm
O163mm*
900mm
1175mm
(maximum)
328mm
593mm
rangehood. Please read this manual carefully before using
the product. This manual should be kept in a safe place for
handy reference.
This canopy rangehood is a domestic appliance which has
been manufactured and tested to comply with Australian
and New Zealand Standard AS/NZS 60335.2.31.
caution
This symbol indicates the possibility of injury or damage to
property
Meanings of symbols used in this manual are shown below:
This symbol indicates never to do this
This symbol indicates always do this
caution
Read the following carefully to avoid an electric
shock or fire.
Canopy dimensions (EFC9563X / EFC9561X)
Young children should be supervised to ensure they do not
play with the canopy rangehood.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning the use of the
appliance by a person responsible for their safety.
Ensure the canopy rangehood is switched off before carrying
out maintenance, to avoid any possibility of electric shock.
Never carry out flambé cooking under the canopy rangehood.
This canopy rangehood is not recommended for barbeques.
This canopy rangehood cannot be installed for external use.
Grease filters must be removed every four weeks
(maximum) for cleaning to reduce the risk of fire.
The exhaust from the canopy rangehood must not
be discharged into any heating flue, which may carry
combustion products from other sources. (Fig. 1)
Exhaust air must not be discharged into a wall cavity, unless
the cavity is designed for the purpose.
There must be adequate ventilation of the room when the
canopy rangehood is used at the same time as appliances
burning gas or other fuels.
Always cover lit gas burners with pots or pans when canopy
rangehood is in use.
Always switch off gas burners before you remove pots or pans.
Do not leave lit gas burners exposed due to the risk of fire.
(Fig. 2)
Electrical Connection
• Checkthatthemainsvoltagematcheswiththevoltage
on the data plate inside the canopy rangehood.
• Checkthattheinstallationcomplieswithstandardsof
local gas and electricity authorities.
• Ifthesupplycordisdamaged,itmustbereplacedby
the manufacturer or its service agent of similarly qualified
person in order to avoid a hazard.
1. Using a spirit level mark a vertical centre line on the wall
100mm
344mm
303mm
37mm
155mm 155mm
71mm
324mm
349mm
374mm
399mm
523mm
ceiling
wall mounting
brackets
ceiling
mounted
bracket
hood
base
top
of hob
anti-tilt fixing points
168mm168mm
(rear view of
hood)
(rear to wall)
46mm
(recommended area
behind flue cover for
power point location)
100mm
(rear view of
hood)
102mm
525mm
46mm
359mm
266mm
25mm
155mm155mm
ceiling
wall mounting
brackets
ceiling
mounted
bracket
168mm168mm
anti-tilt
fixing points
(rear to wall)
138mm 138mm
lower back
edge of glass
top
of hob
(recommended area
behind flue cover for
power point location)
where the hood is to be positioned, and a horizontal line
at the hood base position (refer diagram bottom left).
NOTE: The height of the underside of the hood body must
be a minimum of 600mm above an electric cooktop &
650mm above a gas cook top and a maximum height of
800mm (refer to table below).
Distance from hood base to top of hob
hob type minimum* maximum
gas 650mm 800mm
electric 600mm 800mm
*Iftheinstructionsofthehobspecifyagreaterdistancethanthe
minimum above, then that shall be the minimum height for installation
2. Mark the location for the wall and ceiling bracket fixing
points above the hood base using the hood base as the
reference point (refer diagram bottom left).
3. Installwallandceilingmountingbracketswithsuitable
screws (to support a total weight of 30kg) to the wall at the
positions marked in diagram bottom left.
4. Remove the protective plastic film from the hood body
and hang hood on the mounting brackets then secure at
the anti-tilt locations as indicated in diagram bottom left.
Depending on the preferred installation/ducting mode,
follow step 5a or 5b below.
5a. Recirculating mode (Fig. a). Using the centre line, secure
the ceiling mount bracket to the wall using suitable
screws (screws not supplied). Attach the recirculating
T-piecetotheceilingmountbracket.Installexiblepipe
between T-piece and fan transition outlet. Use cable ties
or suitable duct tape to secure flexible pipe to T-piece.
NOTE: When installed in recirculation mode, it is
recommended to use a carbon filter to prevent odours
being emitted back into the room.
OR
5b. Ducted mode (Fig. b). The canopy rangehood has been
supplied with flexible exhaust pipe and duct transition
piece, alternatively a 150mm dia. non-combustible flue
pipe can be used. Continue the centre line to the ceiling.
Attach the ceiling mount bracket on the centre line. Fit
preferred flue pipe to the fan transition duct.
(a)
(b)
low lock medium high light auto off
OFFboost
1 min.
caution
Loading...