Page 1
ARCTIS
Upright Freezer
Operating Instructions
818 19 26-01/8
Page 2
Dear customer,
Pri
Before placing your new freezer into operation please read these
operating instructions carefully. They contain important information
for safe use, for installation and for care of the appliance.
Please keep these operating instructions for future reference. Pass them
on to possible new owners of the appliance.
Notes which are important for your safety or for the proper
1
functioning of the appliance are stressed with a warning triangle and/
or with signal words (Warning!, Caution!, Important!). Please observe
the following carefully.
0 1. This symbol and numbered instructions guide you step by step in the
operation of the appliance.
2. .....
Supplementary information regarding operation and practical
3
applications of the appliance appear after this symbol.
Tips and notes concerning economical and environmentally sound use
2
of the appliance are marked with the cloverleaf.
Explanations of the technical terminology used in the operating
instructions can be found at the end in the section "Technical
Terminology".
The operating instructions contain instructions for the correction of
possible malfunctions by the user in the section "Something not
working". If these instructions should not be sufficient, please contact
your local AEG Service Force Centre.
nted on paper manufactured with environmentally sound processes.
he who thinks ecologically acts accordingly ...
2 818 19 26-01/8
Page 3
Contents
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Environmental Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Old Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Appliance Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
The freezer needs air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Appliance Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Reversing the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Opening the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
View of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Freezer tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cold accumulation block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Temperature setting buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Temperature display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
FAST FREEZE-button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Prior to Initial Start–Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Initial use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Temperature Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Switching the Appliance Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Control and Information Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Temperature Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Function Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
818 19 26-01/8 3
Page 4
Contents
Freezing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Frozen Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Preparation of Ice Cubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Storage Goods Symbols/Freezing Calendar . . . . . . . . . . . . . . . . . . . . . . . . 24
Maximum Load/Stacking Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Hints and Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Normal Operating Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Food Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Energy Saving Advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Maintenance and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Internal Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
External Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Regulations, Standards, Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Something Not Working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Technical Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Guarantee Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Service & Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4 818 19 26-01/8
Page 5
1 Important Safety Instructions
These warnings are provided in the interests of your safety. Ensure
that you understand them all before installing or using this appliance. Your safety is of paramount importance. If you are unsure
about any of the meanings of these warnings contact the Customer
Care Department.
Prior to Installation
• Check the freezer for transport damage. Under no circumstances
should a damaged appliance be installed! In the event of damage,
please contact your retailer.
Installation
• This appliance is heavy. Care should be taken when moving it.
• It is dangerous to alter the specifications or attempt to modify this
product in any way.
• Ensure that the appliance does not stand on the electrical supply
cable. If the supply cable is damaged, it must be replaced by a cable
available from your local Service Force Centre.
• Any electrical work required to install this appliance should be carried
out by a qualified electrician or competent person.
• Parts which heat up should not be exposed. Whenever possible, the
back of the appliance should be close to a wall, but leaving the
required distance for ventilation, as stated in the installation instructions.
• The appliance should be left for 4 hours after installation before it is
turned on, in order to allow the refrigerant to settle.
Refrigerant
The refrigerant isobutane (R600a) is contained within the refrigerant
circuit of the appliance, a natural gas with a high level of environmental compatibility, which is nevertheless flammable.
• During transportation and installation of the appliance, be certain
that none of the components of the refrigerant circuit become damaged.
• If the refrigerant circuit should become damaged:
– avoid open flames and sources of ignition;
– thoroughly ventilate the room in which the appliance is situated.
818 19 26-01/8 5
Page 6
Important Safety Instructions
Child Safety
• Do not allow children to tamper with the controls or play with the
product.
• Keep packaging material away from children! (There is a risk of suffocation!)
During Use
• This appliance is designed for domestic use only, specifically for the
storage of edible foodstuffs only. It is not intended for commercial or
industrial use.
• Containers with flammable gases or liquids can leak at low temperatures. Do not store any containers with flammable materials such as,
spray cans, fire extinguisher refill cartridges etc in the freezer.
• Frozen food should not be refrozen once it has thawed out.
• Do not place carbonated or fizzy drinks in the freezer.
• Ice lollies can cause ’frost/freezer burns’ if consumed straight from
the freezer compartment.
• Do not remove items from the freezer compartment if your hands are
damp/wet, as this could cause skin abrasions or frost/freezer burns.
• Bottles and cans must not be placed in the freezer. They can burst
when the contents freeze.
• Manufacturers´ recommended storage times should be adhered to.
Refer to relevant instructions.
Maintenance and Cleaning
• Before cleaning, always switch off the appliance and disconnect from
the electrical supply.
• When unplugging always pull the plug from the mains socket, do not
pull on the cable.
Servicing
• This product should be serviced by an authorised engineer and only
genuine spare parts should be used.
• Under no circumstances should you attempt to repair the appliance
yourself. Repairs carried out by inexperienced persons may cause
injury or serious malfunctioning.
Contact your local AEG Service Force Centre.
6 818 19 26-01/8
Page 7
Environmental Information
Packaging
All transit packaging materials are environmentally compatible and can
be reused. Wood is un-treated. The plastics can be recycled and are
identified as follows:
>PE< for polyethylene, e.g. the outer covering and the bags in the interior.
>PS< for polystyrene foam, e.g. the pads, which are pure hydrocarbon
compounds and can be recycled.
The carton parts are made from recycled paper. Please dispose of the
packaging with due care for the environment.
Old Appliances
When disposing of your old appliance:
Make the appliance unusable by cutting off the cable and remove any
door catches to ensure small children cannot be trapped inside.
Help to keep your country tidy - use an authorised disposal site.
Appliance Transport
Two persons are required for transport of the appliance. There are two
recessed handles at the front of the base and at the back of the appliance at the top for improved gripping.
0 1. Grip the appliance with the recessed handles positioned as in the draw-
ing, and transport the appliance.
2. In order to push the appliance into its final position, press carefully at
the top of the door and tip the appliance back slightly. The weight is
then transferred to the back wheels and the appliance can be easily
pushed.
818 19 26-01/8 7
Page 8
Before Use
Packaging
0 1. Remove all adhesive tape and packaging from the interior of the appli-
ance.
Any remnants of adhesive can be removed with white spirit.
3
2. Remove the transport protection pieces and pull off the adhesive tape.
3. Wash the inside of the appliance with lukewarm water with a little
bicarbonate of soda added (5 ml to 0.5 litre of water). Do not use soap
or detergent as the smell may linger. Dry the appliance thoroughly.
8 818 19 26-01/8
Page 9
Installation
Installation Location
The appliance should be installed in a well ventilated, dry room.
Energy use and efficient performance of the appliance is affected by
the ambient temperature.
The appliance should therefore
– not be exposed to direct sunlight;
– not be installed next to radiators, cookers or other sources of heat;
– only be installed at a location whose ambient temperature corre-
sponds to the climate classification, for which the appliance is
designed.
The climate classification can be found on the rating plate, which is
located at the left on the inside of the appliance.
The following table shows which ambient temperature is correct for
each climate classification:
Climate classification for an ambient temperature of
SN +10 to +32 °C
N +16 to +32 °C
ST +18 to +38 °C
T +18 to +43 °C
818 19 26-01/8 9
Page 10
Installation
The freezer needs air
Air is fed under the door through the
vent slots in the base and is exhausted
upwards along the back wall. To ensure
proper air circulation never cover or
alter the vent openings.
Important! If the appliance is installed
under, for example, a hanging cabinet, a
clearance of at least 10 cm between the
top of the appliance and the cabinet
above it must be maintained.
Please check whether, after installing
your appliance and especially after
reversing the door, the door seal fits
tightly. A badly fitting door seal may lead to heavy frosting and a
higher power consumption (see also “Something not working“).
Appliance Alignment
0 1. The appliance must be level. Please compensate for unevenness in the
floor by turning the two adjustable feet at the front.
2. When two appliances are placed beside each other, the spacers
enclosed in the plastic wrapping should be glued between the appliances as shown in the illustration.
10 818 19 26-01/8
Page 11
Electrical Connection
Any electrical work required to install this appliance should be carried
out by a qualified electrician or competent person.
WARNING – THIS APPLIANCE MUST BE EARTHED
1
The manufacturer declines any liability should these safety measures
not be observed.
Before switching on, make sure the electricity supply voltage is the
same as that indicated on the appliance rating plate. The rating plate is
inside, on the left.
The appliance is supplied with a 13 amp plug fitted. In the event of
having to change the fuse in the plug supplied, a 13 amp ASTA
approved (BS 1362) fuse must be used.
Important
The wires in the mains lead are coloured in accordance with the following code:
Green
Green and Yellow Earth
Blue Neutral
Brown Live
As the colours of the wires in the
mains lead of this appliance may
not correspond with the coloured
markings indentifying the termi-
Blue
nals in your plug, proceed as follows:
1. The wire coloured green and
yellow must be connected to
the terminal marked with the
letter “E“ or by the earth symbol or coloured green and yellow.
2. The wire coloured blue must be connected to the terminal “N“ or
coloured black.
3. The wire coloured brown must be connected to the terminal marked
“L“ or coloured red.
4. Upon completion there must be not cut, or stray strands of wire
present and the cord clamp must be secure over the outer sheat.
& Yellow
Installation
Brown
Cord Clamp
Warning! A cut-off plug inserted into a 13 amp socket is a serious
1
safety (shock) hazard. Ensure that the cut-off plug is disposed of safely.
818 19 26-01/8 11
Page 12
Reversing the door
The door hinges can be changed from right (as supplied) to left if
required to suit the location where the appliance is installed.
Warning! Unplug from the mains before reversing the door.
1
Open the door and remove the
plinth cover to the front. Move
the door bearing cover on the
plinth cover from the left to the
right. Close the door.
0 1. With the door closed, remove the
cross-head screws from the lower
door bearing and remove the door
bearing downwards.
2. Remove the door fitting from the
door bearing (1, 2). Move the
bearing pivot from the right to
the left hand hole (3). Place the
door fitting supplied on the bearing pivot (4, 5).
12 818 19 26-01/8
1
4
5
2
3
Page 13
3. Remove the door fitting on the
lower right (1) and reposition the
door bearing cover from the lower
left to the right of the door (2),
place the door fitting supplied in
the lower left of the door (3).
Carefully remove the door to the
front and place on one side.
4. Move the upper bearing pivot to
the left.
Reversing the door
5. Carefully slide the door onto the
top bearing pivot and close.
6. Place the lower door bearing with
the bearing pivot in the lower left
of the door and fasten.
818 19 26-01/8 13
Page 14
7. Move the door handle from the
left to the right and cover the
remaining holes with the hole
cover pins attached.
8. Open the door and fit the plinth
cover.
Opening the door
If the door is closed when the appliance is in operation, it cannot be
immediately opened again, because a vacuum occurs which holds the
door closed until pressure has been equalised. The door can be opened
again after several minutes.
If your appliance is equipped
with a QUICK door opener - an
opening mechanism integrated into the door handle the door can be opened easily
at any time.
14 818 19 26-01/8
Page 15
Description of the appliance
View of the appliance
(various models)
á Control panel
à Freezer tray with ice cube tray and cold accumulation block
â Compartments with lids and drawers (for storage and freezing)
ä Drawer (for frozen food storage only) The bottom drawer also
serves as a water collector when defrosting
Freezer tray
There is a freezer tray with an ice cube tray and a freezer pack located
in the freezer under the top freezer compartment.
Berries, for example, can be pre-frozen on the freezer tray. Advantage:
3
The berries are not squashed and maintain their natural form. The frozen berries can then be stored in compartments or drawers packaged in
individual portions.
818 19 26-01/8 15
Page 16
Description of the appliance
Cold accumulation block
There is one cold accumulation block in the freezer tray.
Refer to the section “Prior to Initial Start–Up” concerning freezing of
the cold accumulation block.
In the event of a power failure or malfunction, the cold accumulation
3
block will increase the hold over period by several hours, providing
it is placed in the uppermost drawer, at the front, above the frozen
food.
You can also use the cold accumulation block in a cool bag.
Control Panel
1 ON/OFF indicator light (green)
2 ON/OFF button
3 Temperature display
4 Temperature setting buttons
5 FAST FREEZE indicator light (yellow)
6 FAST FREEZE button
• FAST FREEZE for fast freezing fresh food
7 Warning indicator light (red)
8 WARNING OFF button
(see section: "Control and Information Systems")
16 818 19 26-01/8
Page 17
Description of the appliance
Temperature setting buttons
The temperature is adjusted using the
„+“ (WARMER) and „-“ (COLDER) buttons.
These buttons are connected to the temperature display.
• The temperature display is switched over from the display of the
ACTUAL temperature (one light illuminated) to the display of the
DESIRED temperature (one light flashing) by pressing one of the two
buttons, „+“ (WARMER) or „-“ (COLDER).
• With each further press of one of the two buttons, the DESIRED tem-
perature is adjusted by one display field.
• If neither button is pressed, the temperature display automatically
switches back after a short period (approx. 5 sec.) to the display of
the ACTUAL temperature.
DESIRED temperature means:
The temperature that is required in the freezer compartment, this can
be adjusted to the temperatures shown in the display. The DESIRED
temperature is indicated by a flashing light.
ACTUAL temperature means:
The temperature display indicates the temperature that is currently
present in the freezer compartment. The ACTUAL temperature is indicated by a continuously illuminated light.
Temperature display
The temperature display can indicate several pieces of information.
• During normal operation, the temperature currently present in the
appliance (ACTUAL temperature) is displayed, the corresponding light
illuminates.
• If the temperature in the freezer compartment is warmer than the
display range of the temperature display, the red warning light
flashes and all the lights in the temperature display are extinguished.
• If the temperature in the freezer compartment is colder than the dis-
play range of the temperature display, then the light for the lowest
temperature (-24) continues to illuminate.
• When the temperature is being adjusted, the temperature currently
set flashes (DESIRED temperature).
• If there is a malfunction in the appliance that prevents the tempera-
ture from being further measured, all the lights on the temperature
display flash.
818 19 26-01/8 17
Page 18
FAST FREEZE-button
The FAST FREEZE function provides for quick freezing of
fresh food products, and at the same time protects previously stored goods against undesired warming in the
freezer compartment.
0 1. The FAST FREEZE function is switched on by pressing the FAST FREEZE
button. The yellow light illuminates.
2. The FAST FREEZE function can be ended manually at any time by pressing the FAST FREEZE button again. The yellow light goes out.
If the FAST FREEZE function is not ended manually, the appliance electronics switch off the FAST FREEZE function after 48 hours. The yellow
light goes out.
Prior to Initial Start–Up
Before connecting the appliance to the mains and putting it into oper-
1
ation for the first time, leave the appliance to stand for 30 minutes if
was transported upright. After transport on its side, the appliance must
be left to stand for 2 hours before putting it into operation. This is necessary to allow the refrigerant to flow back into the compressor. Otherwise the compressor may be damaged.
0 1. Please clean the appliance interior and all accessories prior to initial
start-up (see section: “Maintenance and Cleaning”).
2. Remove the cold accumulation block from the appliance.
3. Only put the cold accumulation block to freeze in the top compartment
after the optimal storage temperature of –18 °C has been reached.
4. After 24 hours place the cold accumulation block in the uppermost
compartment, at the front, above the frozen food.
5. Re-freeze the thawed cold accumulation block in the same way, e. g.
after cleaning the appliance.
18 818 19 26-01/8
Page 19
Initial use
0 1. Insert plug into mains socket.
2. Press ON/OFF button. The green pilot light illuminates. The compressor
starts and then runs automatically.
A warning tone sounds and the red warning light flashes indicating
that the required storage temperature has not yet been reached.
3. Press the WARNING OFF button to switch off the warning tone.
4. Set temperature to -18°C or colder (see section: "Temperature Adjust-
ment").
Important! Wait until the freezer compartment has reached a temperature of –18 °C, or the red warning light has gone out, before storing
frozen food.
Temperature Adjustment
0 1. Press either the „+“ (WARMER) or „-“ (COLDER) button.
The temperature display switches over and the DESIRED temperature
currently set flashes on the temperature display.
2. To adjust to a warmer temperature, press the „+“ button. To adjust to a
colder temperature, press the „-“ button. The changed setting is immediately displayed on the temperature display.
The temperature is adjusted by one display field with each press of a
button.
Note: From a food safety point of view, -18 °C for the freezer compartment should be considered cold enough as a storage temperature.
If the buttons are not pressed again for approx. 5 seconds the tempera-
3
ture display will change from the DESIRED temperature to the ACTUAL
temperature. The display changes from flashing to continuous illumination.
Important! Please check red warning display and temperature display
regularly to assure maintenance of the storage temperature.
818 19 26-01/8 19
Page 20
Switching the Appliance Off
0 1. To switch off, press the ON/OFF button until the mains power light
extinguishes.
Note:
The appliance cannot be switched on or off if unplugged, or if there is
no power being supplied to it.
Following connection to the mains power supply, the appliance returns
to the same operating state as before the interruption of main power.
If the appliance is not going to be used for an extended period:
0 1. Switch off the appliance, to do this press the ON/OFF button until the
mains power light extinguishes.
2. Unplug or switch off at the mains supply.
3. Defrost freezer compartment and clean thoroughly (see section: "Main-
tenance and Cleaning").
4. Leave door open after defrosting to avoid accumulation of odours.
20 818 19 26-01/8
Page 21
Control and Information Systems
The control and information systems consist of the temperature display,
an optical warning display and an acoustic warning.
The system warns if:
– if the temperature in the freezer compartment is too warm;
– functional disturbances at the appliance.
Temperature Warning
The red warning display flashes and an audible warning sounds, as soon
as the temperature in the freezer compartment is warmer than -12 °C.
A rise in temperature may be caused by:
– frequent door opening for long periods of time;
– loading with large quantities of warm foods;
– high ambient temperature;
– an error with the appliance.
The audible warning can be switched off with the WARNING OFF button. Both warning display and audible warning are automatically
switched off, when the ACTUAL temperature in the freezer compartment falls to the range of the display.
The warning tone switches off automatically after one hour, even if the
3
ACTUAL temperature is still at a variance with the DESIRED temperature. The red warning light continues to flash.
Function Errors
If the electronics in the appliance have detected a fault that prevents
the ACTUAL temperature being measured, all the lights in the temperature display will flash. The appliance will continue to function using a
backup programme until a Service Force engineer has repaired the
appliance.
818 19 26-01/8 21
Page 22
Freezing
Except for the bottom drawer, which serves for storage purposes, all
compartments and drawers are suited for freezing.
Important!
• The temperature in the freezer compartment must be –18 °C or
colder before freezing food.
• Please observe the freezing capacity given on the rating plate. The
freezing capacity is the maximum quantity of fresh food that can be
frozen within a period of 24 hours. If you wish to freeze food several
days in a row, please observe a maximum capacity of only 2/3 to 3/4
of that on the rating plate.
• Allow warm food to cool down before freezing. The warmth will
cause increased ice formation and increase the power consumption.
• When freezing large quantities of food, place the frozen cold accu-
mulation block at the front into the top compartment in the freezing
chamber.
• Thawed foods which have not been processed further (cooked into
meals) may not under any circumstances be frozen a second time.
0 1. When freezing maximum capacity press the FAST FREEZE button 24
hours prior to freezing, or 4 to 6 hours for smaller quantities. Yellow
indicator light illuminates.
The FAST FREEZE button need not be pressed for freezing of small
3
quantities of up to 3 kg.
2. All foods must be packed air tight prior to freezing, so that they do not
dry out or lose their flavour, and so that no flavour contamination of
other frozen goods occurs.
Caution! Do not touch frozen food with wet hands. Your hands could
freeze to the food.
3. Place the packed food in the drawers. Unfrozen food must not touch
items already frozen, otherwise the frozen food could begin to defrost.
The appliance electronics automatically switch the FAST FREEZE func-
3
tion off after a period of 48 hours. Yellow indicator light goes out. You
can also stop the FAST FREEZE function manually by pressing the FAST
FREEZE button again.
22 818 19 26-01/8
Page 23
Tips:
• The following are suited for the packaging of frozen goods:
– freezer bags and polyethylene wraps;
– plastic containers for frozen goods;
– extra–thick aluminium foil.
• The following are suitable for sealing bags and wrap:
plastic clips, rubber bands or tape.
• Smooth the air out of the bag before sealing; air makes it easier for
the frozen food to dry out.
• Make flat packages, because these freeze more quickly.
• Do not fill plastic containers for frozen goods to the brim with liquid
or paste–like goods, because liquids expand during freezing.
Frozen Storage
Important! Wait until the necessary storage temperature of –18 °C has
been reached before storing food already frozen.
• Load the freezer only with packaged frozen goods, so that they do
not dry out or lose their flavour, and so that no flavour contamination of other frozen goods can occur.
• Please observe maximum storage times and expiry dates of frozen
goods.
Place frozen foods in the drawers sorted by type, as far as possible. This
2
will give you a better overview of the contents, avoid extended door
opening and therefore save electricity.
818 19 26-01/8 23
Page 24
Preparation of Ice Cubes
0 1. Fill the ice cube tray 3/4 full with cold water, place it in the freezer and
leave to freeze.
2. To loosen the frozen cubes, either bend the ice cube tray or hold it
under running water for a few seconds.
Important! Never try to free an ice tray that is frozen to the freezer
compartment using pointed or sharp edged objects. Use a soft plastic
scraper.
Storage Goods Symbols/Freezing Calendar
• The symbols on the drawers
show different types of frozen
goods.
• The numbers indicate storage
times in months for the appropriate types of frozen goods. Whether
the upper or lower value of the indicated storage time is valid
depends on the quality of the foods and pre-treating before freezing.
The lower value applies to foods with high fat content.
Maximum Load/Stacking Limit
In order to load large quantities or bulky freezer items, you can remove
the drawers (except for the bottom one) and place the freezer goods
directly onto the evaporator grid.
However, when the drawers are removed, the freezer goods may not
extend above 20 mm of the storage grid‘s front.
24 818 19 26-01/8
Page 25
Defrosting
During use and when the door is opened, moisture is deposited as frost
inside the appliance, particularly on the evaporator. This frost must be
removed from time to time using a soft plastic scraper. Under no circumstances use hard or pointed objects for this purpose.
The freezer compartment should always be defrosted when the layer of
frost has reached a thickness of approx. 4 millimetres; however at least
once a year. A good time for defrosting is when the appliance is empty
or contains little food.
Warning!
1
• Do not use electrical heating appliances or any other mechanical or
artificial devices to speed up the defrosting process, with the exception of those recommended in these operating instructions.
• Do not use defrosting sprays, they can be hazardous to your health
and/or contain substances that damage plastics.
0 1. If large quantities of frozen goods are in storage, press the FAST FREEZE
button about 12 hours prior to defrosting, so that the frozen goods can
build up a sufficient chill reserve.
Caution! Do not touch frozen food with wet hands. Your hands could
freeze to the food.
2. Remove frozen food, wrap it in several layers of newspaper and store it,
covered, in a cool place.
3. Unplug or switch off at the mains.
4. Remove all the drawers. Place the
bottom drawer directly in front of
the appliance to collect the water
from defrosting. Take out the
drainage channel from its resting
position at the bottom of the
freezer compartment and place it
as shown.
Tip: In order to speed up the
defrosting process, place a pot of hot water in the freezer
compartment. In addition, remove pieces of ice that break away before
defrosting is complete.
5. After defrosting, thoroughly clean the freezer compartment and interior fittings ( see "Maintenance and Cleaning" section).
818 19 26-01/8 25
Page 26
Hints and Tips
Normal Operating Sounds
• You may hear faint gurgling or bubbling sounds when the refrigerant
is pumped through the coils or tubing at the rear, to the cooling
plate/evaporator.
• When the compressor is on, the refrigerant is being pumped round
and you will hear a whirring sound or pulsating noise from the compressor.
• A thermostat controls the compressor and you will hear a faint click
when the thermostat cuts in and out.
Food Storage
To obtain the best performance from your freezer:
• Do not store warm food or evaporating liquids.
• Do not store food uncovered.
• Keep the time between buying chilled food and placing it in your
freezer as short as possible.
• Do not push food together too much, try to allow air to circulate
around each item.
2 Energy Saving Advice
• Do not install the appliance close to sources of heat, such as a cooker,
dishwasher or radiator.
• Locate the appliance in a cool well ventilated room and make sure
that the air openings of the appliance are not obstructed.
• Always leave warm food to cool down to room temperature before
placing in the freezer.
• Try to avoid keeping the door open for long periods or opening the
door too frequently as warm air will enter the cabinet and cause the
compressor to switch on unnecessarily often.
• Ensure there are no obstructions preventing the door from closing
properly.
26 818 19 26-01/8
Page 27
Maintenance and Cleaning
Before any maintenance or cleaning work is carried out DISCONNECT
the appliance from the ELECTRICITY supply.
Internal Cleaning
0 1. Defrost the freezer compartment (see section: "Defrosting").
2. Clean the inside and accessories with warm water and bicarbonate of
soda (5 ml to 0.5 litre of water). Rinse and dry thoroughly.
Warning!
1
• Do not use detergents, abrasive powders, highly perfumed cleaning
products, wax polishes or cleaning products containing bleach or
alcohol.
3. Regularly check the door seals and wipe clean to ensure they are clean
and free from debris.
External Cleaning
0 1. Wash the outer cabinet with warm soapy water.
Warning!
1
• Do not use abrasive products
• There are sharp edges on the underside of the product so care should
be taken when cleaning.
Accumulation of dust at the condenser increases energy consumption.
2
For this reason carefully clean the condenser at the back of the appliance once a year with a soft brush or a vacuum cleaner.
Regulations, Standards, Guidelines
This appliance was designed for household use and was manufactured
in accordance with the appropriate standards. The necessary measures
in accordance with appliance safety legislation regulations (GSG), accident prevention regulations for refrigeration appliances (VBG 20) and
the regulations of the German Society of Electrical Engineers (VDE)
were observed in the manufacture of this appliance.
The refrigerant circuit has been checked for leaks.
This appliance is in accordance with the following EU guidelines:
;
– 73/23/EWG dated 19 February 1973 - low voltage guidelines.
– 89/336/EWG dated 3 May 1989
(including guideline change notice 92/31/EWG) - EMV guideline
818 19 26-01/8 27
Page 28
Something Not Working
Before contacting your local Service Force Centre, check the following
points.
Sympton Solution
Check there is power at the socket
No power to the appliance.
All the lights in the temperature display
are flashing.
The temperature in the freezer is too high.
The compressor runs continuously
Excessive build up of frost.
Check there is not a power cut by
checking the household lights.
Check the fuse has not blown.
There is a function error.
Inform customer service. Do not open the
door of appliance any more.
Check the ambient temperature is within
the appliances operating limits
Check the temperature regulator is turned to the correct setting relative to
ambient conditions.
Adjust the temperature regulator to give
correct temperature control.
Check that the door is closed.
Large quantities of food have recently
been placed in the cabinet and/or door is
frequently opened.
Check that air ventilation is not
obstructed.
If the door seal is not airtight (probably
after reversing the door) apply warm air
to the non sealing area using a hair dryer
set to a gentle heat. (do not use a fan
heater for this purpose). This will make
the rubber more supple and allow it to
revert to its original shape.
Noise Refer to Normal Operating Sounds
The compressor does not start immediately after changing the temperature setting.
This is normal, the compressor starts after
a period of time.
28 818 19 26-01/8
Page 29
If after the above checks there is still a fault, call your local AEG Service
Force Centre.
In-guarantee customers should ensure that the above checks have been
made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for in-guarantee service
calls.
Technical Terminology
• Refrigerant
Liquids that can be used to a generate a cooling effect are known as
refrigerants. They have a relatively low boiling-point, indeed so low,
that the warmth from the food stored in the fridge or freezer can
cause the refrigerant to boil and vaporise.
• Refrigerant Circuit
Closed circulation system that contains the refrigerant. The refrigerant circuit comprises primarily of an evaporator, a compressor, a condenser and pipe work.
• Evaporator
The refrigerant is evaporated in the evaporator. Similar to all other
liquids, refrigerant requires heat to evaporate. This heat is removed
from the interior of the appliance, as a result the interior is cooled.
The evaporator is therefore located inside the appliance or placed in
foam immediately behind the inner wall and thus not visible.
• Compressor
The compressor looks like a small drum. It is driven by a built-in electric motor and is mounted on the base of the appliance at the rear.
The task of the compressor is to draw in vaporised refrigerant from
the evaporator, to compress it, and to pass it on to the condenser.
• Condenser
The condenser normally has the form of a grid. The refrigerant compressed in the compressor is liquefied in the condenser. During this
process, heat is released to the surrounding air at the surface of the
condenser. The condenser is mounted on the base of the appliance.
818 19 26-01/8 29
Page 30
Guarantee Conditions
We, AEG, undertake that if within 12 months of the date of the purchase this AEG
appliance or any part thereof is proved to be defective by reason only of faulty
workmanship or materials, we will, at our discretion repair or replace the same FREE OF
CHARGE for labour, materials or carriage on condition that:
• The appliance has been correctly installed and used only on the electricity or gas
supply stated on the rating plate.
• The appliance has been used for normal domestic purposes only, and in accordance
with the manufacturer's operating and maintenance instructions.
• The appliance has not been serviced, maintained, repaired, taken apart or tampered
with by any person not authorised by us.
• All service work under this guarantee must be undertaken by a Service Force Centre.
Any appliance or defective part replaced shall become the Company's property.
• This guarantee is in addition to your statutory and other legal rights.
• Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be
available outside these hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
• Damage or calls resulting from transportation, improper use or neglect, the
replacement of any light bulbs or removable parts of glass or plastic.
• Costs incurred for calls to put right an appliance which is improperly installed or calls
to appliances outside the United Kingdom.
• Appliances found to be in use within a commercial environment, plus those which
are subject to rental agreements.
• Products of AEG manufacture which are not marketed by AEG.
European Guarantee
If you should move to another country within Europe then your guarantee moves with
you to your new home subject to the following qualifications:
• The guarantee starts from the date you first purchased your product.
• The guarantee is for the same period and to the same extent for labour and parts as
exists in the new country of use for this brand or range of products.
• This guarantee relates to you and cannot be transferred to another user.
• Your new home is within the European Community (EC) or European Free Trade Area.
• The product is installed and used in accordance with our instructions and is only used
domestically, i.e. a normal household.
• The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to
give them details of your new home. They will then ensure that the local Service
Organisation is aware of your move and able to look after you and your appliances..
France Senlis +33 (0) 3 44 62 29 29
Germany Nürnberg +49 (0) 800 234 7378
Italy Pordenone +39 (0) 800 117511
Sweden Stockholm +46 (0) 8 672 5360
UK Slough +44 (0) 1753 219899
30 818 19 26-01/8
Page 31
Service & Spare Parts
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact Service Force by telephoning:
08705 929 929
Your telephone call will be automatically routed to the Service Force
Centre covering your post code area.
For the adress of your local Service Force Centre and further information about Service Force, please visit the website at
www.serviceforce.co.uk
Before calling out an engineer, please ensure you have read the details
under the heading „What to do if.....“
When you contact the Service Force Centre you will need to give the
following details:
1 Your name, address and post code
2 Your telephone number
3 Clear and concise details of the fault
4 Date of purchase
5 The model and serial number of the appliance (found on the rating
plate)
•Model Name
• Model Number (PNC)
• Serial Number (S-No.)
Please note that a valid purchase receipt or guarantee documentation
is required for in-guarantee service calls.
Customer Care
For general enquiries concerning your AEG appliance or for further
information on AEG products please contact our Customer Care
Department by letter or telephone at the address below or visit our
website at www.aeg.co.uk.
Customer Care Department
AEG Domestic Appliances
55-77 High Street
Slough
Berkshire SL 1 1DZ
Tel: 08705 350350 *
* calls may be recorded for training purposes.
818 19 26-01/8 31
Page 32
From the Electrolux Group. The world´s No.1 choice.
The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more
than 150 countries around the world.
AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg.hausgeraete.de
© Copyright by AEG
818 1926 – 01/8 - 0103
Subject to change without notice
Loading...