Page 1
aeg.com/register
FFX32617ZW
aeg.com\register
EN User Manual | Dishwasher
Page 2
Welcome to AEG! Thank you for choosing our appliance.
Get usage advice, brochures, trouble shooter, service and repair information:
www.aeg.com/support
Subject to change without notice.
CONTENTS
1. SAFETY INFORMATION................................................................................ 2
2. SAFETY INSTRUCTIONS.............................................................................. 4
3. PRODUCT DESCRIPTION............................................................................. 6
4. CONTROL PANEL.......................................................................................... 7
5. PROGRAMMES.............................................................................................. 8
6. OPTIONS...................................................................................................... 10
7. SETTINGS.................................................................................................... 10
8. BEFORE FIRST USE....................................................................................13
9. DAILY USE....................................................................................................14
10. HINTS AND TIPS........................................................................................ 16
11. CARE AND CLEANING.............................................................................. 18
12. TROUBLESHOOTING................................................................................ 20
13. TECHNICAL INFORMATION......................................................................24
14. ENVIRONMENTAL CONCERNS................................................................25
1. SAFETY INFORMATION
Before the installation and use of the appliance, carefully read
the supplied instructions. The manufacturer is not responsible
for any injuries or damage that are the result of incorrect
installation or usage. Always keep the instructions in a safe
and accessible location for future reference.
1.1 Children and vulnerable people safety
• This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the
hazards involved.
• Children between 3 and 8 years of age and persons with
very extensive and complex disabilities shall be kept away
from the appliance unless continuously supervised.
2 ENGLISH
Page 3
• Children of less than 3 years of age should be kept away
from the appliance unless continuously supervised.
• Children should be supervised to ensure that they do not
play with the appliance.
• Keep detergents away from children.
• Keep children and pets away from the appliance when the
door is open.
• Children shall not carry out cleaning and user maintenance
of the appliance without supervision.
1.2 General Safety
• This appliance is for cleaning household-type dishes and
tableware only.
• This appliance is designed for single household domestic
use in an indoor environment.
• This appliance may be used in offices, hotel guest rooms,
bed & breakfast guest rooms, farm guest houses and other
similar accommodation where such use does not exceed
(average) domestic usage levels.
• Do not change the specification of this appliance.
• The operating water pressure (minimum and maximum)
must be between 0.05 (0.5) / 1 (10) MPa (bar).
• Follow the maximum number of 13 place settings.
• The appliance door should not be left in an open position to
avoid the tripping hazard.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
• WARNING: Knives and other utensils with sharp points
must be loaded in the basket with their points down or
placed in a horizontal position.
• Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the socket.
• Do not use high pressure water sprays and/or steam to
clean the appliance.
ENGLISH 3
Page 4
• If the appliance has ventilation openings in the base, they
must not be covered e.g. by a carpet.
• The appliance is to be connected to the water mains using
the new supplied hose-sets. Old hose sets must not be
reused.
2. SAFETY INSTRUCTIONS
2.1 Installation
WARNING!
Only a qualified person must install this
appliance.
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Follow the installation instructions supplied
with the appliance.
• Always take care when moving the
appliance as it is heavy. Always use safety
gloves and enclosed footwear.
• Do not install or use the appliance where
the temperature is less than 0 °C.
• Install the appliance in a safe and suitable
place that meets installation requirements.
2.2 Electrical connection
WARNING!
Risk of fire and electric shock.
• Warning: this appliance is designed to be
installed / connected to a grounding
connection in the building.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable. Should
the mains cable need to be replaced, this
must be carried out by our Authorised
Service Centre.
• Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug.
• This appliance is fitted with a 13 A mains
plug. If it is necessary to change the mains
plug fuse, use only a 13 A ASTA (BS
1362) fuse (UK and Ireland only).
2.3 Water connection
• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not
used for a long time, where repair work
has been carried out or new devices fitted
(water meters, etc.), let the water flow until
it is clean and clear.
• Ensure that there are no visible water
leaks during and after the first use of the
appliance.
• If the water inlet hose is damaged,
immediately close the water tap and
disconnect the mains plug from the mains
socket. Contact the Authorised Service
Centre to replace the water inlet hose.
• Without electrical power, the water
protection system is not active. In this
case there is a risk of flooding.
• The water inlet hose has a safety valve
and a sheath with an inner mains cable.
4 ENGLISH
Page 5
WARNING!
Dangerous voltage.
2.4 Use
• Do not put flammable products or items
that are wet with flammable products in,
near or on the appliance.
• Dishwasher detergents are dangerous.
Follow the safety instructions on the
detergent packaging.
• Do not drink and play with the water in the
appliance.
• Do not remove the dishes from the
appliance until the programme is
complete. Some detergent may remain on
the dishes.
• Do not store items or apply pressure on
the open door of the appliance.
• The appliance can release hot steam if
you open the door while a programme
operates.
2.5 Service
• To repair the appliance contact the
Authorised Service Centre. Use original
spare parts only.
• Please note that self-repair or nonprofessional repair can have safety
consequences and might void the
guarantee.
• The following spare parts are available for
at least 7 years after the model has been
discontinued: motor, circulation and drain
pump, heaters and heating elements,
including heat pumps, piping and related
equipment including hoses, valves, filters
and aquastops, structural and interior
parts related to door assemblies, printed
circuit boards, electronic displays,
pressure switches, thermostats and
sensors, software and firmware including
reset software. The following spare parts
are available for at least 10 years after the
model has been discontinued: door hinge
and seals, other seals, spray arms, drain
filters, interior racks and plastic
peripherals such as baskets and lids. The
duration may be longer in your country.
For further information, please visit our
website.
• Please note that some of these spare
parts are only available to professional
repairers, and that not all spare parts are
relevant for all models.
• Concerning the lamp(s) inside this product
and spare part lamps sold separately:
These lamps are intended to withstand
extreme physical conditions in household
appliances, such as temperature,
vibration, humidity, or are intended to
signal information about the operational
status of the appliance. They are not
intended to be used in other applications
and are not suitable for household room
illumination.
2.6 Disposal
WARNING!
Risk of injury or suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children
and pets to get closed in the appliance.
ENGLISH 5
Page 6
3. PRODUCT DESCRIPTION
5
4
8
10
9
11
67
12
2
3
1
Worktop
1
Upper spray arm
2
Lower spray arm
3
Filters
4
Rating plate
5
Salt container
6
Air vent
7
Rinse aid dispenser
8
Detergent dispenser
9
Cutlery basket
10
Lower basket
11
Upper basket
12
The graphic is a general overview. For
more details, refer to other chapters or
documents provided with the appliance.
6 ENGLISH
Page 7
4. CONTROL PANEL
1
68 7
2 4 53
On/off button
1
Program button
2
Programme indicators
3
Display
4
Delay button
5
4.1 Indicators
Indicator Description
Salt indicator. It is on when the salt container needs refilling. It is always off while the pro‐
gramme operates.
Rinse aid indicator. It is on when the rinse aid dispenser needs refilling. It is always off while
the programme operates.
Washing phase indicator. It is on when the washing phase operates.
Rinsing phase indicator. It is on when the rinsing phase operates.
Drying phase indicator. It is on when you select a programme with the drying phase. It flash‐
es when the drying phase operates.
Delay indicator. It is on when you set the delay start.
GlassCare indicator.
ExtraPower indicator.
Option button
6
Indicators
7
Start button
8
ENGLISH 7
Page 8
Indicator Description
ExtraHygiene indicator.
5. PROGRAMMES
The order of the programmes in the table may not reflect their sequence on the control panel.
Programme Dishwasher
load
Crockery, cut‐
1)
lery, pots, pans
Crockery, cut‐
lery, pots, pans
Crockery, cut‐
lery, pots, pans
Crockery, cutlery Fresh, lightly
Crockery, cutlery Fresh
Crockery, cut‐
3)
lery, pots, pans
Degree of
soil
Normal, lightly
dried-on
Normal to
heavy, dried-on
Normal, lightly
dried-on
dried-on
All
Programme phases Options
• Prewash
• Dishwashing 50 °C
• Intermediate rinse
• Final rinse 55 °C
• Drying
• AirDry
• Prewash
• Dishwashing 60 °C
• Intermediate rinse
• Final rinse 60 °C
• Drying
• AirDry
• Dishwashing 60 °C
• Intermediate rinse
• Final rinse 55 °C
• Drying
• AirDry
• Dishwashing 60 °C
• Intermediate rinse
• Final rinse 50 °C
• AirDry
• Dishwashing 50 °C
• Intermediate rinse
• Final rinse 50 °C
• AirDry
• Prewash
• Dishwashing 50 - 60 °C
• Intermediate rinse
• Final rinse 60 °C
• Drying
• AirDry
2)
2)
2)
2)
2)
2)
• ExtraPower
• GlassCare
• ExtraHygiene
• ExtraPower
• GlassCare
• ExtraHygiene
• ExtraPower
• GlassCare
• ExtraHygiene
• ExtraPower
• GlassCare
• ExtraHygiene
• ExtraPower
• GlassCare
• ExtraHygiene
8 ENGLISH
Page 9
Programme Dishwasher
load
4)
5)
1)
This programme offers the most efficient use of water and energy consumption for crockery and cutlery with
normal soil. This is the standard programme for test institutes. This programme is used to assess compliance with
the Ecodesign Comission Regulation (EU) 2019/2022. This programme is used to assess compliance with the UK
Ecodesign for Energy-Related Products and Energy Information Regulations.
2)
Automatic door opening during the drying phase. Refer to "Settings".
3)
The appliance senses the degree of soil and the quantity of items in the baskets. It automatically adjusts the
temperature and the quantity of water, the energy consumption and the programme duration.
4)
This programme is designed to clean the inside of the appliance effectively and efficiently. It removes limescale
and grease buildup. The programme should be run at least once every 2 months with a descaler or a cleaning
product designed for dishwashers and without any load.
5)
With this programme, you can quickly rinse off food remains from dishes and prevent odours forming in the ap‐
pliance. Do not use detergent with this programme.
None Cleaning the
All All
Degree of
soil
appliance inte‐
rior
Programme phases Options
• Cleaning 70 °C
• Intermediate rinse
• Final rinse
• AirDry
• Prewash
2)
5.1 Consumption values
Programme
1)
The pressure and the temperature of the water, the variations of the mains supply, the options, the quantity of
dishes and the degree of soil can change the values.
2)
The values for programmes other than ECO are indicative only.
1)2)
Water (l) Energy (kWh) Duration (min)
9.9 0.936 240
11.6 1.110 160
10.6 0.990 90
10.6 0.860 60
10.2 0.620 30
12.4 1.170 170
9.7 0.510 60
4.2 0.020 15
5.2 Information for test institutes
To receive the necessary information for conducting performance tests (e.g. according to:
EN60436 /BS EN60436 ), send an email to:
info.test@dishwasher-production.com
ENGLISH 9
Page 10
In your request, include the product number code (PNC) from the rating plate.
For any other questions regarding your dishwasher, refer to the service book provided with
your appliance.
6. OPTIONS
prevents rapid changes in the dishwashing
temperature of the selected programme and
Desired options must be activated every
time before you start a programme.
It is not possible to activate or deactivate
options while a programme is running.
The option button toggles between the
available options and their possible
combinations.
Not all options are compatible with each
other. If you select non compatible
options, the appliance automatically
deactivates one or more of them. Only
the indicators of the still active options
are on.
reduces it to 45 °C.
How to activate GlassCare
Press Option until the indicator is on.
The display shows the updated programme
duration.
6.2 ExtraPower
This option improves the dishwashing results
of the selected programme. It increases the
wash temperature and duration.
How to activate ExtraPower
Press Option until the indicator is on.
The display shows the updated programme
duration.
If an option is not applicable to a
programme, the related indicator is off or
it flashes quickly for a few seconds and
then goes out.
Activating options can affect the water
and energy consumption as well as the
programme duration.
6.1 GlassCare
This option protects a delicate load,
glassware in particular, from damaging. It
7. SETTINGS
7.1 Programme selection mode and user mode
When the appliance is in programme
selection mode, you can set a programme
and enter user mode.
10 ENGLISH
6.3 ExtraHygiene
This option provides better cleaning results
by keeping the temperature between 65 and
70 °C for at least 10 minutes during the last
rinsing phase.
How to activate ExtraHygiene
Press Option until the indicator is on.
The display shows the updated programme
duration.
Settings available in the user mode:
• The level of water softener according to
the water hardness.
• Activation or deactivation of the rinse aid
empty notification.
Page 11
• Activation or deactivation of the AirDry.
The saved settings remain valid until you
change them again.
To enter user mode, press and hold
simultaneously Delay and Option until the
indicators , and
flash and the display is blank.
How to set the programme selection mode
The appliance is in programme selection
mode when the programme indicator
is on and the display shows the programme
duration.
After activation, the appliance is in
programme selection mode by default. If not,
set the programme selection mode the
following way:
Press and hold simultaneously Delay and
Option until the appliance is in programme
selection mode.
7.2 The water softener
The water softener removes minerals from
the water supply, which would have a
negative effect on the washing results and on
the appliance.
The higher the content of these minerals, the
harder your water is. Water hardness is
measured in equivalent scales.
The water softener should be adjusted
according to the hardness of the water in your
area. Your local water authority can advise
you on the hardness of the water in your
area. Set the right level of the water softener
to assure good washing results.
How to enter user mode
Make sure the appliance is in programme
selection mode.
Water hardness
German de‐
grees (°dH)
47 - 50 84 - 90 8.4 - 9.0 835 - 904 58 - 63 10
43 - 46 76 - 83 7.6 - 8.3 755 - 834 53 - 57 9
37 - 42 65 - 75 6.5 - 7.5 645 - 754 46 - 52 8
29 - 36 51 - 64 5.1 - 6.4 505 - 644 36 - 45 7
23 - 28 40 - 50 4.0 - 5.0 395 - 504 28 - 35 6
19 - 22 33 - 39 3.3 - 3.9 325 - 394 23 - 27
15 - 18 26 - 32 2.6 - 3.2 255 - 324 18 - 22 4
11 - 14 19 - 25 1.9 - 2.5 185 - 254 13 - 17 3
4 - 10 7 - 18 0.7 - 1.8 70 - 184 5 - 12 2
<4 <7 <0.7 <70 < 5
1)
Factory setting.
2)
Do not use salt at this level.
French de‐
grees (°fH)
mmol/l mg/l (ppm) Clarke de‐
grees
Water softener
level
1)
5
2)
1
Regardless of the type of detergent used,
set the proper water hardness level to
keep the salt refill indicator active.
Multi-tabs containing salt are not effective
enough to soften hard water.
ENGLISH 11
Page 12
Regeneration process
For the correct water softener operation, the
resin of the softener device needs to be
regenerated regularly. This process is
automatic and is the part of the normal
dishwasher operation.
When the prescribed quantity of water (see
values in the table) has been used since the
previous regeneration process, a new
regeneration process will be initiated between
the final rinse and the programme end.
Water softener level Amount of water (l)
1 250
2 100
3 62
4 47
5 25
6 17
7 10
8 5
9 3
10 3
when it occurs at any point at the beginning
or in the middle of a programme.
All the consumption values mentioned in
this section are determined in line with
the currently applicable standard in
laboratory conditions with water hardness
2.5mmol/L (water softener: level 3)
according to the regulation: 2019/2022 /
UK Ecodesign 2021/745.
The pressure and the temperature of
water as well as the variations of the
mains supply can change the values.
How to set the water softener level
Make sure the appliance is in user mode.
1. Press Program.
• The indicator still flashes.
• The remaining indicators are off.
• The display shows the current setting:
e.g. = level 5.
2. Press Program repeatedly to change the
setting.
3. Press the on/off button to confirm the
setting.
In case of the high water softener setting, it
may occur also in the middle of the
programme, before the rinse (twice during a
programme). Regeneration initiation has no
impact on the cycle duration, unless it occurs
in the middle of a programme or at the end of
a programme with a short drying phase. In
such cases, the regeneration prolongs the
total duration of a programme by additional 5
minutes.
Subsequently, the rinsing of the water
softener that lasts 5 minutes may begin in the
same cycle or at the beginning of the next
programme. This activity increases the total
water consumption of a programme by
additional 4 litres and the total energy
consumption of a programme by additional 2
Wh. The rinsing of the softener ends with a
complete drain.
Each performed softener rinse (possible more
than one in the same cycle) may prolong the
programme duration by another 5 minutes
12 ENGLISH
7.3 The rinse aid empty notification
The rinse aid helps to dry the dishes without
streaks and stains. It is automatically
released during the final rinse.
When the rinse aid chamber is empty, the
rinse aid indicator turns on. If the drying
results are satisfactory while using multitablets only, you can deactivate the
notification for refilling the rinse aid. However,
for best drying performance, always use rinse
aid.
If standard detergent or multi-tablets without
rinse aid are used, activate the notification to
keep the rinse aid refill indicator active.
How to deactivate the rinse aid empty notification
Make sure the appliance is in user mode.
1. Press Start.
• The indicator still flashes.
Page 13
• The remaining indicators are off.
• The display shows the current setting.
– = the rinse aid empty
notification is deactivated.
– = the rinse aid empty
notification is activated.
2. Press Start to change the setting.
3. Press the on/off button to confirm the
setting.
7.4 AirDry
AirDry improves the drying results with less
energy consumption. The appliance door
opens automatically during the drying phase
and remains ajar.
AirDry is automatically activated with all
programmes other than (if applicable).
The duration of the drying phase and the door
opening time vary depending on the selected
programme and options.
When AirDry opens the door, the display
shows the remaining time of the running
programme.
CAUTION!
Do not try to close the appliance door
within 2 minutes after automatic opening.
This can cause damage to the appliance.
If, afterwards, the door is closed for at
least 3 minutes, the running programme
ends.
CAUTION!
If children have access to the appliance,
we advise to deactivate AirDry. The
automatic opening of the door may pose
a danger.
How to deactivate AirDry
Make sure the appliance is in user mode.
1. Press Delay.
• The indicator still flashes.
• The remaining indicators are off.
• The display shows the current setting:
– = AirDry is deactivated.
– = AirDry is activated.
2. Press Delay to change the setting.
3. Press the on/off button to confirm the
setting.
8. BEFORE FIRST USE
1. Make sure that the current level of the
water softener agrees with the
hardness of the water supply. If not,
adjust the level of the water softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start a programme to remove any
processing residuals that can still be
inside the appliance. Do not use
detergent and do not put dishes in the
baskets.
After starting the programme, the appliance
recharges the resin in the water softener for
up to 5 minutes. The washing phase starts
only after this procedure is complete. The
procedure is repeated periodically.
8.1 The salt container
CAUTION!
Use only regeneration salt for
dishwashers. Do not use kitchen salt.
ENGLISH 13
Page 14
The salt is used to recharge the resin in the
M
A
X
1
2
3
4
+
-
A B
D
C
water softener and to assure good washing
results in daily use.
How to fill the salt container
1. Turn the cap of the salt container
counterclockwise and remove it.
2. Put 1 litre of water in the salt container
(only for the first time).
3. Fill the salt container with 1 kg of salt
(until it is full).
4. Carefully shake the funnel by its handle to
get the last granules inside.
5. Remove the salt around the opening of
the salt container.
8.2 How to fill the rinse aid dispenser
CAUTION!
The compartment (A) is for rinse aid only.
Do not fill it with detergent.
CAUTION!
Only use rinse aid designed specifically
for dishwashers.
1. Press the release button (D) to open the
lid (C).
2. Fill the dispenser (A) until the rinse aid
reaches the marking ''MAX''.
3. Remove the spilled rinse aid with an
absorbent cloth to prevent excessive
foam formation.
4. Close the lid. Make sure that the release
button locks into position.
6. Turn the cap clockwise to close the salt
container.
CAUTION!
Water and salt can come out of the salt
container when you fill it. To prevent
corrosion, fill the salt container and then
immediately start a complete
dishwashing cycle with detergent.
9. DAILY USE
1. Open the water tap.
2. Press the on/off button to activate the
appliance.
14 ENGLISH
You can turn the selector of the released
quantity (B) between position 1 (lowest
quantity) and position 4 or 6 (highest
quantity).
Make sure that the appliance is in programme
selection mode.
• If the salt indicator is on, fill the salt
container.
Page 15
• If the rinse aid indicator is on, fill the
20
30
A
B
C
rinse aid dispenser.
3. Load the baskets.
4. Add the detergent.
5. Set and start a programme suitable for
the type of load and the degree of soil.
9.1 Using the detergent
CAUTION!
Only use detergent specifically designed
for dishwashers.
1. Press the release button (B) to open the
lid (C).
2. Put the detergent, in powder or tablets, in
the compartment (A).
3. If the programme has a prewash phase,
put a small quantity of detergent on the
inner part of the appliance door.
4. Close the lid. Make sure that the release
button locks into position.
For information about the detergent
dosage, refer to the manufacturer's
instructions on the packaging of the
product. Usually, 20 - 25 ml of gel
detergent is adequate for washing a load
with normal soil.
Do not fill the compartment (A) with more
than 30 ml of gel detergent.
9.2 Setting and starting a programme
The Auto off function
This function decreases energy consumption
by deactivating automatically the appliance
when it is not operating.
The function comes into operation:
• When the programme is complete.
• After 5 minutes if a programme was not
started.
Starting a programme
1. Press the on/off button to activate the
appliance. Make sure that the appliance
is in programme selection mode and the
door is closed.
2. Press Program again and again until the
indicator of the desired programme is on.
The display shows the programme duration.
3. Set the applicable options.
4. Press Start to start the programme.
• The indicator of the running phase is
on.
• The programme duration starts to
decrease with steps of 1 minute.
Starting a programme with delay start
1. Set a programme.
2. Press Delay repeatedly until the display
shows the desired delay time (from 1 to
24 hours).
3. Press Start to begin the countdown.
• The indicator
• The remaining time counts down in
hours. The final hour is displayed in
minutes.
When the countdown is completed, the
programme starts and the indicator of the
running phase is on. The indicator is off.
is on.
Opening the door while the appliance operates
Opening the door while a programme is
running stops the appliance. It may affect the
energy consumption and the programme
ENGLISH 15
Page 16
duration. After closing the door, the appliance
continues from the point of interruption.
Press simultaneously Delay and Option until
the appliance is in programme selection
mode.
If the door is opened for more than 30
seconds during the drying phase, the
running programme ends. It does not
happen if the door is opened by AirDry
function.
Do not try to close the appliance door
within 2 minutes after AirDry
automatically opens it as this may cause
damage to the appliance.
If, afterwards, the door is closed for at
least 3 minutes, the running programme
ends.
Cancelling the delay start while the countdown operates
When you cancel the delay start you have to
set the programme and options again.
10. HINTS AND TIPS
10.1 General
Follow the hints below to ensure optimal
cleaning and drying results in daily use and to
protect the environment.
• Washing dishes in the dishwasher as
instructed in the user manual usually
consumes less water and energy than
washing dishes by hand.
• Load the dishwasher to its full capacity to
save water and energy. For best cleaning
results, arrange items in the baskets as
instructed in the user manual and do not
overload the baskets.
• Do not pre-rinse dishes by hand. It
increases the water and energy
consumption. When needed, select a
programme with a prewash phase.
• Remove larger residues of food from the
dishes and empty cups and glasses
before putting them inside the appliance.
• Soak or slightly scour cookware with firmly
cooked-on or baked-on food before
washing it in the appliance.
Cancelling the programme
Press and hold simultaneously Delay and
Option until the appliance is in programme
selection mode.
Make sure that there is detergent in the
detergent dispenser before you start a new
programme.
End of the programme
When the programme is complete, the Auto
off function switches the appliance off
automatically.
All buttons are inactive except for the on/off
button.
Close the water tap.
• Make sure that items in the baskets do not
touch or cover each other. Only then can
the water completely reach and wash the
dishes.
• You can use dishwasher detergent, rinse
aid and salt separately or you can use the
multi-tablets (e.g. ''All in 1''). Follow the
instructions on the packaging.
• Select a programme according to the type
of load and the degree of soil.
offers the most efficient use of water and
energy consumption.
• To prevent limescale buildup inside the
appliance:
– Refill the salt container whenever
necessary.
– Use the recommended dosage of the
detergent and rinse aid.
– Make sure that the current level of the
water softener agrees with the
hardness of the water supply.
– Follow the instructions in the chapter
"Care and cleaning".
16 ENGLISH
Page 17
10.2 Using salt, rinse aid and detergent
• Only use salt, rinse aid and detergent
designed for dishwasher. Other products
can cause damage to the appliance.
• In areas with hard and very hard water, we
recommend to use basic dishwasher
detergent (powder, gel, tablets containing
no additional agents), rinse aid and salt
separately for optimal cleaning and drying
results.
• Detergent tablets do not fully dissolve with
short programmes. To prevent detergent
residues on the tableware, we recommend
that you use tablets with long
programmes.
• Always use the correct quantity of
detergent. Insufficient dosage of detergent
can result in poor cleaning results and
hard-water filming or spotting on the items.
Using too much detergent with soft or
softened water results in detergent
residues on the dishes. Adjust the amount
of detergent based on the water hardness.
Refer to the instructions on the detergent
packaging.
• Always use the correct quantity of rinse
aid. Insufficient dosage of rinse aid
decreases the drying results. Using too
much rinse aid results in bluish layers on
the items.
• Make sure that the water softener level is
correct. If the level is too high, the
increased quantity of salt in the water
might result in rust on cutlery.
10.3 What to do if you want to stop
using multi-tablets
Before you start to use separately detergent,
salt and rinse aid, complete the following
steps:
1. Set the highest level of the water
softener.
2. Make sure that the salt and rinse aid
containers are full.
3. Start the shortest programme with a
rinsing phase. Do not add detergent and
do put dishes in the baskets.
4. When the programme is complete, adjust
the water softener according to the water
hardness in your area.
5. Adjust the released quantity of rinse aid.
6. Activate the rinse aid empty notification.
10.4 Loading the baskets
• Always use the whole space of the
baskets.
• Use the appliance to wash dishwashersafe items only.
• Do not wash in the appliance items made
of wood, horn, aluminium, pewter and
copper as they could crack, warp, get
discoloured or pitted.
• Do not wash in the appliance items that
can absorb water (sponges, household
cloths).
• Put hollow items (cups, glasses and pans)
with the opening facing downwards.
• Make sure that glass items do not touch
each other.
• Put light items in the upper basket. Make
sure that the items do not move freely.
• Put cutlery and small items in the cutlery
basket.
• Move the upper basket upwards to
accommodate large items in the lower
basket.
• Make sure that the spray arms can move
freely before you start a programme.
10.5 Before starting a programme
Before you start the selected programme,
make sure that:
• The filters are clean and correctly
installed.
• The cap of the salt container is tight.
• The spray arms are not clogged.
• There is enough salt and rinse aid (unless
you use multi-tablets).
• The arrangement of the items in the
baskets is correct.
• The programme is suitable to the type of
load and the degree of soil.
• The correct quantity of detergent is used.
10.6 Unloading the baskets
1. Let the tableware cool down before you
remove it from the appliance. Hot items
can be easily damaged.
2. First remove items from the lower basket,
then from the upper basket.
ENGLISH 17
Page 18
After the programme is completed, water
C
B
A
can still remain on the inside surfaces of
the appliance.
11. CARE AND CLEANING
WARNING!
Before maintenance, deactivate the
appliance and disconnect the mains plug
from the main socket.
Dirty filters and clogged spray arms
decrease the washing results. Make a
check regularly and, if necessary, clean
them.
11.1 Internal cleaning
• Clean the appliance interior with a soft
damp cloth.
• Do not use abrasive products, abrasive
cleaning pads, sharp tools, strong
chemicals, scourer or solvents.
• Wipe clean the door, including the rubber
gasket, once a week.
• To maintain the performance of your
appliance, use a cleaning product
designed for dishwashers at least once
every two months. Carefully follow the
instructions on the packaging of the
product.
• Use the automatic cleaning programme for
optimal cleaning results.
• Using short-duration programmes
regularly can cause grease and limescale
buildup inside the appliance. Run longduration programmes at least twice a
month to prevent the buildup.
CAUTION!
If unable to remove the foreign objects,
contact an Authorised Service Centre.
1. Disassemble the filters system as
instructed in this chapter.
2. Remove any foreign objects manually.
3. Reassemble the filters as instructed in
this chapter.
11.3 External cleaning
• Clean the appliance with a moist soft
cloth.
• Only use neutral detergents.
• Do not use abrasive products, abrasive
cleaning pads or solvents.
11.4 Cleaning the filters
The filter system is made of 3 parts.
11.2 Removal of foreign objects
Check the filters and the sump after each use
of the dishwasher. Foreign objects (e.g.
pieces of glass, plastic, bones or toothpicks,
etc) decrease the cleaning performance and
can cause damage to the drain pump.
18 ENGLISH
1. Turn the filter (B) counterclockwise and
remove it.
Page 19
2. Remove the filter (C) out of filter (B).
3. Remove the flat filter (A).
4. Wash the filters.
5. Make sure that there are no residues of
food or soil in or around the edge of the
sump.
6. Put back in place the flat filter (A). Make
sure that it is correctly positioned under
the 2 guides.
7. Reassemble the filters (B) and (C).
8. Put back the filter (B) in the flat filter (A).
Turn it clockwise until it locks.
CAUTION!
An incorrect position of the filters can
cause bad washing results and damage
to the appliance.
11.5 Cleaning the lower spray arm
We recommend to clean the lower spray arm
regularly to prevent soil from clogging the
holes.
Clogged holes can cause unsatisfactory
washing results.
1. To remove the lower spray arm, pull it
upwards.
ENGLISH 19
Page 20
2. Wash the spray arm under running water.
Use a thin pointed tool, e.g. a toothpick,
to remove particles of soil from the holes.
3. To install the spray arm back, press it
downwards.
11.6 Cleaning the upper spray arm
Do not remove the upper spray arm. If the
openings in the spray arm are clogged,
remove the remaining particles of soil with a
thin pointed object, e.g. a toothpick.
12. TROUBLESHOOTING
WARNING!
Improper repair of the appliance may
pose a danger to the safety of the user.
Any repairs must be performed by
qualified personnel.
The majority of problems that may occur
can be solved without the need to contact
an Authorised Service Centre.
Problem and alarm code Possible cause and solution
You cannot activate the appliance.
• Make sure that the mains plug is connected to the mains socket.
• Make sure that there is no damaged fuse in the fuse box.
20 ENGLISH
Refer to the below table for information on
possible problems.
With some problems, the display shows an
alarm code.
Page 21
Problem and alarm code Possible cause and solution
The programme does not start.
The appliance does not fill with wa‐
ter.
The display shows i10 or i11.
The appliance does not drain the
water.
The display shows i20.
The anti-flood device is on.
The display shows i30.
Malfunction of the water level detec‐
tion sensor.
The display shows i41 - i44.
Malfunction of the wash pump or the
drain pump.
The display shows i51 - i59 or i5A i5F.
The temperature of the water inside
the appliance is too high or malfunc‐
tion of the temperature sensor oc‐
curred.
The display shows i61 or i69.
Technical malfunction of the appli‐
ance.
The display shows iC0 or iC3.
The level of water inside the appli‐
ance is too high.
The display shows iF1.
The appliance stops and starts
more times during operation.
The programme lasts too long.
The displayed programme duration
is different than the duration in the
consumption values table.
• Make sure that the appliance door is closed.
• Press the start button.
• If the delay start is set, cancel the setting or wait for the end of the
countdown.
• The appliance recharges the resin inside the water softener. The dura‐
tion of the procedure is approximately 5 minutes.
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not too low. For this
information, contact your local water authority.
• Make sure that the water tap is not clogged.
• Make sure that the filter in the inlet hose is not clogged.
• Make sure that the inlet hose has no kinks or bends.
• Make sure that the sink spigot is not clogged.
• Make sure that the interior filter system is not clogged.
• Make sure that the drain hose has no kinks or bends.
• Close the water tap.
• Make sure that the appliance is correctly installed.
• Make sure the baskets are loaded as instructed in the user manual.
• Make sure that the filters are clean.
• Switch the appliance off and on.
• Switch the appliance off and on.
• Make sure that the temperature of the inlet water does not exceed
60°C.
• Switch the appliance off and on.
• Switch the appliance off and on.
• Switch the appliance off and on.
• Make sure that the filters are clean.
• Make sure that the outlet hose is installed at the right height above the
floor. Refer to the installation instructions.
• It is normal. It provides optimal cleaning results and energy savings.
• If the delayed start is set, cancel the delay setting or wait for the end of
the countdown.
• The pressure and the temperature of the water, the variations of the
mains supply, the options, the quantity of dishes and the degree of soil
can change the programme duration.
ENGLISH 21
Page 22
Problem and alarm code Possible cause and solution
The remaining time in the display in‐
creases and skips nearly to the end
of programme time.
Small leak from the appliance door.
The appliance door is difficult to
close.
The appliance door opens during
the wash cycle.
Rattling/knocking sounds from in‐
side the appliance.
The appliance trips the circuit-beak‐
er.
• This is not a defect. The appliance is working correctly.
• The appliance is not levelled. Loosen or tighten the adjustable feet (if
applicable).
• The appliance door is not centred on the tub. Adjust the rear foot (if ap‐
plicable).
• The appliance is not levelled. Loosen or tighten the adjustable feet (if
applicable).
• Parts of the tableware are protruding from the baskets.
• The AirDry function is activated. You can deactivate the function. Refer
to "Settings".
• The tableware is not properly arranged in the baskets. Refer to basket
loading leaflet.
• Make sure that the spray arms can rotate freely.
• The amperage is insufficient to supply simultaneously all the applian‐
ces in use. Check the socket amperage and the capacity of the meter
or turn off one of the appliances in use.
• Internal electrical fault of the appliance. Contact an Authorised Service
Centre.
WARNING!
Refer to "Before first use", "Daily use",
or "Hints and tips" for other possible
causes.
Once you have checked the appliance,
deactivate and activate the appliance. If the
We do not recommend using the
appliance until the problem has been
completely fixed. Unplug the appliance
and do not plug it in again until you are
certain that it operates correctly.
problem occurs again, contact an Authorised
Service Centre.
For alarm codes not described in the table,
contact an Authorised Service Centre.
12.1 The dishwashing and drying results are not satisfactory
Problem Possible cause and solution
Poor washing results.
• Refer to "Daily use", "Hints and tips" and the basket loading leaf‐
let.
• Use more intensive washing programme.
• Activate the ExtraPower option to improve the washing results of a
selected programme.
• Clean spray arm jets and filter. Refer to "Care and Cleaning".
22 ENGLISH
Page 23
Problem Possible cause and solution
Poor drying results.
There are whitish streaks or bluish lay‐
ers on glasses and dishes.
There are stains and dry water drops
on glasses and dishes.
The interior of the appliance is wet.
Unusual foam during washing.
Traces of rust on cutlery.
There are residues of detergent in the
dispenser at the end of the pro‐
gramme.
Odours inside the appliance.
• Tableware was left for too long inside the closed appliance. Activate
the function AirDry to set the automatic opening of the door and to
improve the drying performance.
• There is no rinse aid or the dosage of rinse aid is not sufficient. Fill
the rinse aid dispenser or set the dosage of rinse aid to a higher lev‐
el.
• The quality of the rinse aid can be the cause.
• Always use rinse aid, even with multi-tablets.
• Plastic items may need to be towel dried.
• The programme does not have the drying phase. Refer to "Pro‐
grammes overview".
• The released quantity of rinse aid is too high. Adjust the rinse aid
dosage to a lower level.
• The quantity of detergent is too high.
• The released quantity of rinse aid is not sufficient. Adjust the rinse
aid dosage to a higher level.
• The quality of the rinse aid can be the cause.
• This is not a defect of the appliance. Humidity condensates on the
appliance walls.
• Use the detergent designed specifically for dishwashers.
• Use a detergent from a different manufacturer.
• Do not pre-rinse dishes under running water.
• There is too much salt in the water used for washing. Refer to "The
water softener".
• Silver and stainless steel cutlery were placed together. Do not place
silver and stainless steel items close together.
• The detergent tablet was stuck in the dispenser and was not washed
away by water.
• Water cannot wash away the detergent from the dispenser. Make
sure that the spray arms are not blocked or clogged.
• Make sure that items in the baskets do not impede the lid of the de‐
tergent dispenser from opening.
• Refer to "Internal cleaning".
• Start the programme with a descaler or a cleaning product de‐
signed for dishwashers.
ENGLISH 23
Page 24
Problem Possible cause and solution
Limescale deposits on the tableware,
on the tub and on the inside of the
door.
Dull, discoloured or chipped table‐
ware.
• The level of salt is low, check the refill indicator.
• The cap of the salt container is loose.
• Your tap water is hard. Refer to "The water softener".
• Use salt and set regeneration of the water softener even when multifunctional tablets are used. Refer to "The water softener".
• Start the programme with a descaler designed for dishwashers.
• If limescale deposits persist, clean the appliance with the suitable de‐
tergents.
• Try a different detergent.
• Contact the detergent manufacturer.
• Make sure that only dishwasher-safe items are washed in the appli‐
ance.
• Load and unload the basket carefully. Refer to the basket loading
leaflet.
• Place delicate items in the upper basket.
• Activate the GlassCare option to ensure special care for glassware
and delicate items.
Refer to "Before first use", "Daily use",
or "Hints and tips" for other possible
causes.
13. TECHNICAL INFORMATION
Dimensions Width / height / depth (mm) 598 / 850 / 622
Electrical connection
Water supply pressure Min. / max. MPa (bar) 0.05 (0.5) / 1 (10)
Water supply
Capacity Place settings 13
1)
Refer to the rating plate for other values.
2)
If the hot water comes from alternative source of energy (e.g. solar panels), use the hot water supply to de‐
crease energy consumption.
1)
13.1 Link to the EU EPREL database
The QR code on the energy label supplied
with the appliance provides a web link to the
registration of this appliance in the EU
EPREL database. Keep the energy label for
reference together with the user manual and
all other documents provided with this
Voltage (V) 220 - 240
Frequency (Hz) 50
Cold water or hot water
2)
min. 5 - max. 60 °C
It is possible to find information related to the
performance of the product in the EU EPREL
database using the link https://
eprel.ec.europa.eu and the model name and
product number that you can find on the
rating plate of the appliance. Refer to the
chapter "Product description".
appliance.
24 ENGLISH
Page 25
For more detailed information about the
energy label, visit www.theenergylabel.eu.
13.2 Link to the product information sheet - for the UK only
The QR code on the energy label supplied
with the appliance provides a web link to the
product information sheet. Keep the energy
label for reference together with the user
manual and all other documents provided
with this appliance.
For more detailed information about the
energy label, visit www.theenergylabel.eu.
14. ENVIRONMENTAL CONCERNS
Recycle materials with the symbol . Put the
packaging in relevant containers to recycle it.
Help protect the environment and human
health by recycling waste of electrical and
electronic appliances. Do not dispose of
appliances marked with the symbol with
the household waste. Return the product to
your local recycling facility or contact your
municipal office.
ENGLISH 25
*
Page 26
Page 27
Page 28
156825660-A-442023
Loading...