Advantech UNO-1170, UNO-1170E User Manual

UNO-1170/1170E

Pentium M / Celeron M Fanless,
DIN-rail Mounted Embedded
Automation Computer with 2 x LAN,
3 x COM, 4 x USB, Audio & PC/104+

User Manual

Copyright Notice

The documentation and the software included with this product are copy­righted 2009 by Advantech Co., Ltd. All rights are reserved. Advantech
Co., Ltd. reserves the right to make improvements in the products
described in this manual at any time without notice. No part of this man­ual may be reproduced, copied, translated or transmitted in any form or
by any means without the prior written permission of Advantech Co., Ltd.
Information provided in this manual is intended to be accurate and reli­able. However, Advantech Co., Ltd. assumes no responsibility for its use,
nor for any infringements of the rights of third parties, which may result
from its use.

Acknowledgements

IBM, PC/AT, PS/2 and VGA are trademarks of International Business

Machines Corporation.

Intel® and Pentium® are trademarks of Intel Corporation.

Microsoft Windows and MS-DOS are registered trademarks of

Microsoft Corp.

C&T is a trademark of Chips and Technologies, Inc.

All other product names or trademarks are properties of their respective
owners.

Part No. 2003117000 1st Edition

Printed in Taiwan April 2009

UNO-1170 User Manual ii

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its prod­ucts will be free from defects in materials and workmanship for two years
from the date of purchase.

This warranty does not apply to any products which have been repaired or
altered by persons other than repair personnel authorized by Advantech,
or which have been subject to misuse, abuse, accident or improper instal­lation. Advantech assumes no liability under the terms of this warranty as
a consequence of such events.

Because of Advantech’s high quality-control standards and rigorous test­ing, most of our customers never need to use our repair service. If an
Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you will
be billed according to the cost of replacement materials, service time and
freight. Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For
example, CPU speed, Advantech products used, other hardware
and software used, etc.) Note anything abnormal and list any
onscreen messages you get when the problem occurs.

2. Call your dealer and describe the problem. Please have your man­ual, product, and any helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return
merchandize authorization) number from your dealer. This allows
us to process your return more quickly.

4. Carefully pack the defective product, a fully-completed Repair and
Replacement Order Card and a photocopy proof of purchase date
(such as your sales receipt) in a shippable container. A product
returned without proof of the purchase date is not eligible for war­ranty service.

5. Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.

iii

CE

This product has passed the CE test for environmental specifications
when shielded cables are used for external wiring.

FCC Class A

This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer­ence when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

Technical Support and Assistance

Step 1. Visit the Advantech web site at www.advantech.com/support

where you can find the latest information about the product.

Step 2. Contact your distributor or Advantech's customer service center

if you need additional assistance. Have the following info ready:

- Product name and serial number

- Description of your software (OS, version, software, etc.)

- A complete description of the problem

- The exact wording of any error messages

Packing List

Before setting up the system, check that the items listed below are
included. If any item is not, please contact your dealer immediately.

• Software Supporting CD-ROM

• 6P-6P-6P 20cm PS/2 Mouse/Keyboard Y cable (P/N: 1700060202)

• Phoenix power connector (P/N: 1652003206)

• DIN-rail & wall mount accessories

• Key pro bracket

• SATA cable (UNO-1170E only)

• SATA power cable (UNO-1170E only)

• Spacer for PCI-104 expansion (UNO-1170E only)

UNO-1170 User Manual iv

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User's Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning.
Use a damp cloth. Do not use liquid or spray detergents for clean­ing.

4. For plug-in equipment, the power outlet socket must be located
near the equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Drop­ping it or letting it fall may cause damage.

7. The openings on the enclosure are for air convection. Protect the
equipment from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before con­necting the equipment to the power outlet.

9. Position the power cord so that people cannot step on it. Do not
place anything over the power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or elec­trical shock.

13. Never open the equipment. For safety reasons, the equipment
should be opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked
by service personnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well, or you cannot get it to work

according to the user's manual.

e. The equipment has been dropped and damaged.

f. The equipment has obvious signs of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT
WHERE THE STORAGE TEMPERATURE MAY GO BELOW

v

-10° C (14° F) OR ABOVE 60° C (140° F). THIS COULD DAM­AGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A
CONTROLLED ENVIRONMENT.

16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS
INCORRECTLY REPLACED. REPLACE ONLY WITH THE
SAME OR EQUIVALENT TYPE RECOMMENDED BY THE
MANUFACTURER, DISCARD USED BATTERIES ACCORD­ING TO THE MANUFACTURER'S INSTRUCTIONS.

The sound pressure level at the operator's position according to IEC 704­1:1982 is no more than 70 dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1.
Advantech disclaims all responsibility for the accuracy of any statements
contained herein.

Safety Precaution - Static Electricity

Follow these simple precautions to protect yourself from harm and the
products from damage.

1. To avoid electrical shock, always disconnect the power from your
PC chassis before you work on it. Don't touch any components on
the CPU card or other cards while the PC is on.

2. Disconnect power before making any configuration changes. The
sudden rush of power as you connect a jumper or install a card may
damage sensitive electronic components.

UNO-1170 User Manual vi

Contents

Chapter 1 UNO-1170 Overview ....................................... 2

1.1 Introduction ....................................................................... 2

1.2 Hardware Specifications ................................................... 2

1.3 Safety Precautions ............................................................. 3

1.4 UNO-1170 Series .............................................................. 4

1.5 Chassis Dimensions........................................................... 4

Chapter 2 Hardware Functionality ................................. 8

2.1 UNO-1170 Peripherals ...................................................... 8

2.2 COM1~COM2: RS-232 Interfaces ................................. 10

2.3 COM3: RS-232/422/485 Interfaces ................................ 10

2.4 LAN: Ethernet Connector ............................................... 13

2.5 Power Connector ............................................................. 13

2.6 LED Indicators ................................................................ 14

2.7 PS/2 Keyboard and Mouse Connector ............................ 14

2.8 Universal Serial Bus Connectors..................................... 14

2.9 VGA: VGA Display Connector ...................................... 14

2.10 RESET: Reset Button...................................................... 15

2.11 Audio ............................................................................... 15

2.13 LED and Buzzer for System Diagnosis........................... 15

2.14 PCI/104+ Connectors (UNO-1170E only) ...................... 17

Chapter 3 Initial Setup.................................................... 20

3.1 CompactFlash Card Installation ...................................... 20

3.2 USB Keypro and Keypro Bracket Installation ................ 22

3.3 Chassis Grounding .......................................................... 23

3.4 Power Connection ........................................................... 23

3.5 PC/104+ Card Installation (UNO-1170E)....................... 24

3.6 Hard Drive installation (UNO-1170E)............................ 27

3.7 BIOS Setup and System Assignments ............................ 29

Figure 1.1:UNO-1170 Chassis Dimensions ................... 4

Figure 1.2:UNO-1170E Chassis Dimensions ................ 5

Figure 2.1:UNO-1170 Front View ................................. 8

Figure 2.2:UNO-1170 Top View ................................... 8

Figure 2.3:UNO-1170E Front View .............................. 9

Figure 2.4:UNO-1157E Top View ................................ 9

2.3.1 TI 16C550 UARTs with 16-byte Standard .................. 10

2.3.2 Jumperless RS-422/485 ............................................... 10

2.3.3 Automatic Data Flow Control Function for RS-485 ... 10

2.3.4 RS-232/422/485 Selection ........................................... 11

Figure 2.5:RS-422/485 Jumper Settings ...................... 11

Figure 2.6:RS-232 Jumper Settings ............................. 11

2.3.5 Terminal Resistor Setup for RS-422/485 ..................... 12

Figure 2.7:RS-422/485 Jumper Settings ...................... 17

Figure 3.1:Chassis Grounding Connection .................. 23

vii Table of Contents

3.8 DIN-rail Mounting Setup ................................................ 29

3.9 Wallmounting Setup........................................................ 30

Appendix A System Settings and Pin Assignments ......... 32

A.2 Board Connectors and Jumpers....................................... 34

A.3 RS-232 Serial Port (COM1~COM2)............................... 37

A.4 RS-232/422/485 Serial Port (COM3).............................. 38

A.5 Ethernet RJ-45 Connector (LAN1~LAN2)..................... 38

A.6 Power Screw Terminal (CN8)......................................... 39

A.7 PS/2 Keyboard and Mouse Connector (CN10) ............... 39

A.8 USB Connector (CN13) .................................................. 40

A.9 VGA Display Connector (CN15) .................................... 40

A.10 SATA Data Connector (CN17) ....................................... 41

Figure A.1:Connector & Jumper Locations (Top) ....... 34

Figure A.2:Connector & Jumpers (UNO-1170E) ........ 36

Appendix B Programming the Watchdog Timer ............ 44

UNO-1170 User Manual viii

1

CHAPTER

UNO-1170 Overview

Sections include:

• Introduction

• Hardware Specifications

• Safety Precautions

• UNO-1170 Series

• Chassis Dimensions

Chapter 1 UNO-1170 Overview

1.1 Introduction

UNO-1170 is an DIN-rail mounted Embedded Automation Computer, which
provides several serial communication ports and Ethernet interfaces. UNO­1170 is designed with a compact size, small footprint, and help to saves space
with its front accessible and DIN-rail design. With rich OS and driver support,
such as Windows XP embedded, WinCE 6.0, and even embedded Linux. You
can integrate your applications easily with an application ready platform that
can provide a versatile function to fulfill diverse requirements.

1.2 Hardware Specifications

• CPU: Pentium M 1.4GHZ / Celeron M 1 GHZ

• Memory: 512MB/1GB on board

• Battery-backup RAM: 512 KB Battery-backup RAM

• VGA/Keyboard/Mouse: DB-15 VGA Connector, Mini-DIN connector for
PS/2 keyboard & mouse

• Serial Ports: 2 × RS-232 and 1 x RS-232/422/485 with DB-9 connectors.

Automatic RS-485 data flow control

• Serial Speeds: RS-232: 50~115.2 kbps, RS-422/485: 50~921.6 kbps

• LAN: Two 10/100 Base-T RJ-45 Ports

• USB interface: Four USB ports, USB EHCI, Rev. 2.0 compliant. (Including

3 external connectors and 1 internal connector for USB dongle)

• Audio: Mic in, Line in, Line out

• Storage: SSD: 1 x internal type I/II CompactFlash slot

HDD: one 2.5" SATA HDD bracket (Only for UNO-1170E)

• LEDs: Power (Power Standby: Orange, Power on : Green), 3 pairs of serial

flow indicators (Tx, Rx ), -IDE, Alarm for RAM Backup Battery

• PC/104+: PC/104+ slot, Supports +5V Power (Optional, UNO-1170E only)

• Mini PCI: 1x MiniPCI (UNO-1170E only)

• Shock Protection: IEC 68-2-27, CompactFlash: 50G @ Wall mount, half

sine, 11ms (Optional, for UNO-1170E: 20G @ wall mount, half sine, 11ms)

UNO-1170 User Manual 2

• Vibration Protection: IEC 68 2-64 (Random 1 Oct./min, 1hr/axis),

CompactFlash: 2Grms@ 5~500Hz, (Optional, UNO-1170E only)
HDD: 0.5 Grms @ 5~500Hz

• Power Supply Voltage: 10-36 VDC, reversed wiring protection

• Power Requirement: Min. 48 W (10 ~ 53 VDC) (e.g +24 V @ 2 A) (ATX)

• Power Consumption: 24W (Typical)

• Operating Temperature: -20~60° C (-4~149° F)

• Storage Temperature: -20~80° C (-4~176° F)

• Relative humidity: 95% @ 40°C

• Wei ght: 1.6KG (for UNO-1170) 2.0KG (for UNO-1170E)

• Chassis size (W × L × H): 85x155x140 mm (3.4"x 6.1"x 5.6") (UNO-1170)

110 x 155 x 140 mm (4.4" x 6.1" x 5.6") (UNO-1170E)

• Software options: WinXP Embedded, Win CE, Linux

• Certification: CE, FCC Class A, UL

1.3 Safety Precautions

The following sections tell how to make each connection. In most cases, you
will simply need to connect a standard cable. All of the connector pin assign­ments are shown in Appendix A.

Warning!! Always disconnect the power cord from your chassis when

you are working on it. Do not connect while the power is
on. A sudden rush of power can damage sensitive elec­tronic components. Only experienced electronics person­nel should open the chassis.

Caution!! Always ground yourself to remove any static electric

charge before touching UNO-1170. Modern electronic
devices are very sensitive to static electric charges. Use a
grounding wrist strap at all times. Place all electronic com­ponents on a static-dissipative surface or in a static­shielded bag.

3

1.4 UNO-1170 Series

There are four products in UNO-1170 series, as listed below:

UNO-1170-C11E

UNO-1170-P12E

UNO-1170E-C11E

UNO-1170E-P12E

UNO-1170 with Intel Celeron M 1.0GHz CPU
and 512MB RAM

UNO-1170 with Intel Pentium M 1.4GHz CPU
and 1GB RAM

UNO-1170 with Intel Celeron M 1.0GHz CPU,
512MB RAM, and PC/104+ expansion

UNO-1170 with Intel Pentium M 1.4GHz CPU,
1GB RAM and PC/104+ expansion

1.5 Chassis Dimensions

Figure 1.1: UNO-1170 Chassis Dimensions

UNO-1170 User Manual 4

Figure 1.2: UNO-1170E Chassis Dimensions

5

UNO-1170 User Manual 6

Hardware

Functionality

Sections include:

•UNO-1170 Peripherals

•COM1: RS-232 Interfaces

•COM2~3: RS-232/422/485 Interfaces

•LAN: Ethernet Connector

•Power Connector

•LED Indicators

•PS/2 Keyboard and Mouse Connector

•Universal Serial Bus Connectors

•VGA: VGA Display Connector

•RESET: Reset Button

•Audio

• PC/104+ Voltage Selection

2

CHAPTER

Chapter 2 Hardware Functionality

2.1 UNO-1170 Peripherals

The following figures show the connectors on UNO-1170. and UNO­1170E. Information in this chapter is applied to both UNO-1170 and
UNO-1170E. Therefore, in this chapter, we just mention UNO-1150 to
represent the series product. The following sections give you detailed
information about function of each peripheral.

Figure 2.1: UNO-1170 Front View

Figure 2.2: UNO-1170 Top View

UNO-1170 User Manual 8