PCI-7031 Intel® Atom™ Dual-Core D510 N450
CPU, PCI Half-size SBC with on-board DDR2/VGA/
LVDS/Dual GbE/SATA/COM
Startup Manual
Packing List
Before you begin installing your card, please make sure that
the following items have been shipped:
• 1 PCI-7031 Single Board Computer
• 1 CPU Cooler only for D SKU P/N: 1960046526N001
• 1 PCI-7031 Startup Manual
• 1 CD with Driver, Utility and Manual (in PDF format)
• 2 Serial ATA HDD Data Cable P/N: 1700003194
• 1 Serial ATA HDD Power Cable P/N: 1700022749-11
• 1 Printer (parallel) Port Cable Kit P/N: 1701260301
• 1 Dual COM Ports Cable Kit P/N: 1700008762
• 1 ATX Feature Cable P/N: 1700002343
• 1 4-port USB Cable Kit P/N: 1700014398-11
• 1 Y Cable for PS/2 Keyboard P/N: 1700060202
and PS/2 Mouse
• 1 ATX PSU 20-pin to P/N: 1700000265
12-pin Cable Kit
• 1 Jumper Pack P/N: 9689000068
• 1 Warranty Card
If any of these items are missing or damaged, please contact your distributor or sales representative immediately.
Note1: For detailed contents of PCI-7031, please refer
to information on the enclosed CD-ROM (in PDF
format). Acrobat Reader is required to view any
PDF file.
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com/ePlatform/
For technical support and service, please visit our
support website at:
http://support.advantech.com/support/default.aspx
This manual is for the PCI-7031 series Rev. A1
Part No. 2002703113
Printed in China
4th Edition
October 2014
Specications
Specications
Standard SBC functions
• CPU: Soldered-down (BGA type) Intel Atom 1.66 GHz
D510 dual-core CPU or 1.66 GHz N450 fanless CPU
• BIOS: AMI Flash BIOS
• Chipset: ICH8M I/O control hub
• System memory:
- N SKU: 1 GB on-board DDR2 667 memory
- D/DF SKU: Maximum 2 GB DDR2 667 memory by
SO-DIMM socket
Note: PCI-7031 is ONLY compatible with DDR2 memory
modules that are assembled with x16 (16-bit) memory
chips and NOT compatible with those that are assembled
with x 8 (8-bit) memory chips. Using wrong memory modules may cause unexpected system instability.
• IDE interface: One channel, supports one ultra ATA
100/66/33 and one CF slot
• SATA interface: Supports three SATAII HDD (300 MB/s)
• Serial ports: Two dedicated serial RS-232 ports on
board, plus four ports RS-422/485 w/ autoflow control by
module (Advantech P/N: PCA-COM485-00A1E)
• Parallel port: One EPP/ECP parallel port
• Keyboard/mouse connector: One standard PS/2 key-
board/mouse connector and one external 6-pin header
• Watchdog timer: Timer can be set from 1 to 255 seconds
or 1 to 255 minutes
• USB (2.0): 7 Universal Serial Bus ports
VGA Interface
• Chipset: Embedded Gen3.5+ GFX Core technology
• Display memory: 224 MB shared system memory
• Video output:
- Dual display:VGA+LVDS
- D510 (D &DF SKU):
VGA: up to 2048x1536@60Hz
LVDS: 18 bit, 1366x768 or 1280x800
- N450 (N SKU):
VGA: up to 1400x1050@60Hz
LVDS: 18 bit, 1366x768 or 1280x800
Ethernet Interface
• Chipset: Dual GbEs, LAN 1: Intel® 82567V; LAN 2: Intel®
82583V
• Connection: Onboard RJ-45 connectors
PCI-7031 Startup Manual 1
Specications (cont.)
1 2 3
1 2 3
Mechanical and Environmental
• Dimensions (L x W): 185 x 122 mm (7.3” x 4.8”)
• Power supply voltage: +5 V, +12 V, 5 Vsb, +3.3 V
• Power requirements:
PCI-7031D/PCI-7031DF
Intel Atom D510 (1.66GHz), DDR2 667, 2GB*1
Voltage (V) 12V 5V 3.3V 5VSB -12V
Current (A) 0.32 3.59 0.02 0.04 0.03
Total (W) 22.416
PCI-7031N
Intel Atom N450 (1.66GHz), DDR2 667, 1GB onboard
Voltage (V) 12V 5V 3.3V 5VSB -12V
Current (A) 0.16 2.83 0.01 0.04 0.01
Total (W) 16.423
• Operating temperature: 0 ~ 60° C (32 ~ 140° F) (opera-
tion humidity: 40° C @85% RH, Non-Condensing)
• Weight: 0.365 Kg (weight of board)
Jumpers and Connectors
The board has a number of connectors and jumpers that
allow you to configure your system to suit your application.
The table below lists the function of each of the connectors
and jumpers.
Connectors
Label Function
JFP1(1-2) HDD LED connector
JFP1(3-4) Power LED connector
JFP1(5-6) Suspend LED connector
JFP1(7-8) Reset connector
JFP1(9-10) ATX power switch
JIR1 IR connector
IDE1 IDE connector
CF1 CF Socket
FDD1 FDD connector
LPT1 Parallel port
USB12 USB port 1, 2, pin-header
USB34 USB port 3, 4, pin-header
USB56 USB port 5, 6, pin-header
USB8 USB port 8 on rear I/O bracket
SATA 1 Serial ATA1
SATA 2 Serial ATA2
SATA 3 Serial ATA3
COM12 Serial Port: COM1 COM2
2 PCI-7031 Startup Manual
Jumpers and Connectors (cont.)
KBMS1 PS/2 keyboard and mouse connector
KBMS2 External keyboard and mouse connector
VGA1 VGA connector
LAN12 Dual Gigabit Ethernet connector
ATX1 ATX power connector
CPUFAN1 CPU FAN connector (3-pin)
SYSFAN1 System FAN connector (3-pin)
HDAUD1 High Denition audio connector
GPIO1 GPIO pin header
LPC1 LPC connector
LVDS1 LVDS connector
INV1 Inverter connector
Note: USB7 is reserved and can not be used.
Jumpers
Label Function
CMOS1 CMOS clear
JLVDS1 3.3 V / 5 V, LVDS voltage selection
JVBR1 LVDS backlight setting
JWDT1 Watchdog timer output selection
ATXF1 ATX feature connector
CMOS1: CMOS clear function
Closed Pins Result
1-2 Keep CMOS data *
2-3 Clear CMOS
* default setting
JLVDS1: LCD Power 3.3 V/5 V Selector
Closed Pins Result
1-2* 3.3 V*
2-3
* default setting
5 V
1 2 3
Jumpers and Connectors (cont.)
1 2 3
1 2 3
JVBR: LVDS backlight setting
Closed Pins Result
1-2 closed
(Default)
2-3 closed PWM to control brightness
JWDT1: Watchdog timer output option
Closed Pins Result
1-2 GPIO14
2-3
* default setting
ATXF1: AT/ATX mode selection
Closed Pins Result
1-2 (Default)
Connect to backplane with 1700002343 ATX mode
* For DF SKU, jumper setting on ATXF1 is not required,
please do not put the jumper.
Linear way to control brightness
System reset *
AT mode
PCI-7031 Startup Manual 3
Software Installation
The CD disc contains a driver installer program that will lead you through the installation of various device drivers needed to
take full advantage of your CPU card.
Caution! The computer is provided with a battery-powered real-time clock circuit. There is a danger of explosion if battery is
incorrectly replaced. Replace only with same or equivalent type recommended by Advantech. Discard used batteries according to manufacturer’s instructions.
Board Layout
This device complies with the requirements in Part 15 of the FCC rules. Operation is subject to the following two conditions.
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired
operation.
The locations of all connectors and jumpers:
SATA1~3
(300MB/Sec)
IDE1FDD1
Intel ICH8
I/O Control Hub
(D& DF SKU)
DIMMA1
On-board 1GB
DDR2 667 Memory
(Only on N SKU)
LPT1
COM12
COMLED1
VGA1
JIR1
JACSE1
JWDT1
SYSFAN1
LAN12
USB8
KBMS1
KBMS2
Note: USB7 is reserved
and can NOT be used.
USB1~6
LANLED1 GPIO1 LVDS1 HDAUD1 ATXF1
ATX1
Intel Atom
D510/N450 CPU
CMOS1
JFP1
JLVDS1
JVBR1
INV1
CPUFAN1
On-board 1GB
DDR2 667 Memory
(Only on N SKU)
CF1
LPC1
Figure 1: Board Layout: Jumper and Connector Locations
4 PCI-7031 Startup Manual
Loading...