Advance Security X11RF-LCD Users Manual

Download

Page 1

MODEL X11RF-LCD

REMOTE ENGINE STARTER

WITH ALARM SYSTEM

OWNER’S MANUAL

WARNINGS:

As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of.

1. Keep the transmitter out of children’s reach.

2. Do not leave anyone in the vehicle while running on remote control.

3. Alert servicing personnel that the vehicle can be started automatically.

4. Do not start the vehicle by remote while it’s in an enclosed area or garage.

5. Always apply the parking brake and lock the vehicle as you exit the vehicle.

6. The vehicle windows must be rolled up.

7. Should the unit malfunction, disconnect the fuse until the problem is corrected.

8. The use and operations of this system is the sole responsibility of the operator.

9. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets.

10. Do not start the vehicle by remote while the standard transmission vehicle is parked at a steep place.

Page 2

TABLE OF CONTENTS:

A. REMOTE TRANSMITTER OPERATION ……………………………………….………………….……………………….. 4 B. 2-WAY LCD REMOTE CONTROL TRANSCEIVER OPERATION ..…………………………….…………………..…... 4 C. LED DISPLAY .……………..……………………………………………………………………….…………………….……. 4 D. CHIRP INDICATOR ..………..……………………………………………………………………………..…………………... 4 E. PARKING LIGHT …….……..…………………………………………………………………………..………………………. 4 F. ACTIVE ARMING – ARM & LOCK .………………………………………………………………………………………..…. 4

Ajar Warning / Silent Arming / Disarming / Sensor By-Pass / Hidden Alarm Mode

G. PASSIVE ARMING .…………………………………………..………………………………………………………….…..… 5

Passive Arming with Passive Door Locking / Passive Arming By-Pass

H. ACTIVE DISARMING – UNLOCK & DISARM .………………………………………………………………..……………. 5

Tamper Disarming / Pathway Illumination / Two Steps Door Unlock / Automatic Re-Arm

I. DISARMING WITHOUT A TRANSMITTER .……………..…………………………………………………………………... 6

Overrides the Alarm without Password Pin Code / Overrides the Alarm With Password Pin Code

J. VALET MODE .……………..…………………………………………………………………….………….………………….. 6 K. CAR LOCATOR .……………………………………………………………………….……………………………………..… 7 L. PANIC FUNCTION .……………………………………………………………………………..….……………………….….. 7 M. TRIGGER THE SYSTEM .………………………………………..………………………..…………………………………... 7

Stop The Melody Sound / Noise Abatement Circuit

N. ANTI CAR- JACKING .………………………………………………………………………………….………………..…….. 7 O. SYSTEM’S TRIGGER CHECK ……………………………………………………………….….….…..……………………. 8 P. SYSTEM’S STATUS CHECK ……………………………………………………………..……….……………………….…. 8 Q. DRIVER PAGING / LOSE AND FOUND ………………………….…………..……………………...…………………...… 8 R. DOME LIGHT CONVENIENCE DELAY & SUPERVISION ……………………..………………….……………………... 8 S. IGNITION CONTROL THE DOOR LOCK/UNLOCK. ………..………………….……………………………………….…. 9 T. TRUNK RELEASE (CHANNEL 3) OUTPUT ………..……………………………………………….………………………. 9 U. CHANNEL 4 / 5 / 6 / 7 TIMER CONTROL OUTPUT ………..…………………………………………………………..….. 9 V. POWER ON MEMONRY: ………..……………………………………………………………….…….….…………………... 9

REMOTE START OPERATION:

A. TO REMOTE START THE VEHICLE ………..………………………………………………………………………..……... 9 B. TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START ……………………………………..…... 9 C. TEMPORARY STOP FEATURE ……………………………………………….………………….…….………………….… 9 D. TURBO TIMER MODE ……………………..………………………………….……………….………...…………………… 10 E. TIMER / TEMPERATURE START …………………………………………….…………….……..………………………… 10

3 (2 or 1) Hours Timer Start / Daily Timer Start / Cancel the Timer Start

F. TEMPERATURE CHECK …………….……………………………………………….….……….……………………….… 10 G. TO TURN OFF THE REMOTE START ……………………………………………….….…….………………………………11 H. SHUT-DOWN INPUT FOR REMOTE STARTER ………………………….………………………..……………………... 11 I. DISABLING THE REMOTE START SYSTEM …………………………….……………………..…….………………….… 11

LCD REMOTE TRANSCEIVER:

A. BATTERY REPLACEMENT ……………………………….……………………………………………………………….….. 11 B. THE REMOTE LCD ICONS WITH FUNCTION ……….……………………………………………………………………... 11 C. PROGRAMMING OF THE LCD REMOTE TRANSCEIVER …………………………………………………………….…. 12

1. Screen Lamp ON

2. Power Save Mode

3. Clear The Flash Icon and Melody Sound

4. Stop The Melody Sound.

5. Button Lock

6. Vibration / Melody Mode

7. Enable / Disable Bi Sound While Pressing Button:

8. Low Battery Indication.

9. Set Up Fixed Count Down Timer

10. Out Of The Range Check

11. Illumination

12. Second Vehicle Security System Operation

D. TIMER SETTING ……………………………….………………………………………………….………………………..… 14

1. Timer Setting.

2. Alert Alarm Timer Setting

3. Count Down Timer Setting

4. Time Set-Up For “Daily Timer Start”

Page 3

OPERATION:

A. REMOTE TRANSMITTER OPERATION:

Transmitter Button System Function Remark

Lock Doors & Arm System

- -

- Arm System and Hidden Alarm Function Press within 3 seconds

Car Locator Upon armed

Arm and Bypass The Sensor 1 (Zone 4). Arm and Bypass The Sensor 2 (Zone 6). Arm and Bypass The Sensor 1 and 2

Press twice within 3 seconds Press within 5 seconds Press within 5 seconds

(3-second) Panic function Press and Hold for 3 seconds.

+ Silent Arming / Disarming Ignition in "off" position. + (2-second) Active Anti Car-Jacking Mode Ignition in "on" position press and

hold for 2 seconds

Unlock Doors & Disarm System

- Two Steps Door Unlock & Disarm System Press twice within 3 seconds.

Trunk Release (Channel 3) Press and Hold for 1 sec.

- Passive Arming By-pass While the system Disarmed.

- Activate or Turn Off The Remote Start Press twice within 3 seconds.

+ Channel # 4 Timer Output + Channel # 5 Timer Output

+ Channel # 6 Timer Output

+ Channel # 7 Timer Output Defrost outpu t will be auto active 30

sec after R/S succeed; Output will be 1 sec. (-) pulse.

B. 2-WAY LCD REMOTE CONTROL TRANSCEIVER OPERATION ONLY:

Transceiver Button System Function Remark

- (C) System’s Trigger Check Press within 3 seconds

- - (C) System’s Status Check Press within 3 seconds

- ( ) Optional Driving Pager Press within 3 seconds

- ( ) Monitor Indoor Temperature Press within 3 seconds

SET- + 2nd car Operation Press within 3 seconds

C. LED display:

LED Function LED Function Off Disarmed 1 flashes... pause Zone 1 / Trigger on Hood Slow Flash Armed 2 flashes... pause Zone 2 / Trigger on Trunk Fast Flash Passive Arming 3 flashes... pause Zone 3 / Trigger on Door Switch On (Solid) Valet Mode 4 flashes... pause Zone 4 / Trigger on Sensor 1 Pause On Password Lock-Out 5 flashes... pause Zone 5 / Trigger on Ignition Switch

D. CHIRP INDICATORS: E. PARKING LIGHT:

Chirp Function Parking light Function 1 chirp Arm 1 flash Arm 2 chirps Disarm 2 flashes Disarm 3 chirps Ajar Warning 3 flashes Disarm / Triggered 4 chirps Disarm / Triggered 12 flashes Car Locator 6 chirps Car Locator Constant On Under Remote Start

Switching code For 2nd Car Operation. For regular remote transmitter

6 flashes... pause Zone 6 / Trigger on Sensor 2

Page 4

F. ACTIVE ARMING – LOCK & ARM:

1. Press button on the transmitter.

2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The vehicle door will lock upon arming when interfaced with the security system.

System Arm

AJAR WARNING: If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar. SILENT ARMING / DISARMING:

disarm your security system, No chirp sound will be heard, arm / disarm confirmation will be through the vehicles parking lights only.

SENSOR BY-PASS: Bypass The Sensor 1 (Zone 4): Press the

arm the security system and by-pass the sensor 1 (zone 4 shock sensor). Bypass The Sensor 2 (Zone 6): Press the the security system and by-pass the zone 6 optional sensor 2. Bypass The Sensor 1 (Zone 4) and Sensor 2 (Zone 6): Press the the

button twice will arm the security system and by-pass the sensor 1 (zone 4 shock sensor) and zone 6 optional sensor 2. The system will chirp one additional time to confirm the sensor bypass mode was activated. The sensor bypass feature is programmed to activate for one arming cycle only. The security system will return to normal operation during the next arming cycle.

HIDDEN ALARM FUNCTION: Press the button to activate the hidden alarm function. The security system will arm and with “Hidden Alarm Function” The siren / horn will be silenced even if the sensor is triggered

in the armed status. (A melody sounding from your Remote LCD transceiver and “ icon will display on the LCD screen to confirm the hidden alarm was activated.)

Hood Ajar

Press the transmitter and buttons at the same time will arm or

Trunk Ajar

button on the transmitter two times within 3 seconds will button first, with 3 seconds press the button will arm

button first; within 3 seconds press the

Door Ajar

button first, with 3 seconds press

Clear The Flash Icon:

Press the times within 3 seconds will clear the flash icon on the LCD screen transmitter

”

button 3

G. PASSIVE ARMING

Active arming / disarming is controlling your security system via the remote transmitter. This security system is equipped with an optional Passive Arming feature, which allows the security system to arm 30 seconds after the last door is closed. Operation is as follows.

1. Turn the ignition to the “OFF” position and exit the vehicle.

2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any door / hood / trunk, the security system LED will stop flashing. It will begin flashing again once the vehicle all entrances are closed.

3. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren will chirp [1] time and the parking lights will flash [1] time.

PASSIVE ARMING WITH PASSIVE DOOR LOCKING:

The vehicle doors will automatically lock after passive arming cycle has been completed.

PASSIVE ARMING BY-PASS: While the system disarmed, Press the respond with [1] chirp and LED will turn “ON”. The security system will remain in this temporally state for as long as you wish. To exit passive by-pass, press the transmitter return to normal status.

button twice, the security will

button and the system will

H. ACTIVE DISARMING – UNLOCK & DISARM:

1. Press button on the transmitter.

2. The siren will chirp twice and parking light flash twice to indicating that the security system is now disarmed. The vehicle’s door will unlock and dome light turns on for 30 seconds upon disarming when interfaced with the security system.

Page 5

System Disarm

Hood Trigger

Trunk Trigger

Doors Trigger

Ignition Trigger

Sensor 1 Trigger

Sensor 2 Trigger

CLEAR THE FLASH ICON: Press the button 3 times

within 3 seconds will clear the flash icon on the LCD screen transceiver. TAMPER DISARMING: If alarm triggered, upon disarm the system, siren chirp 4 times, parking light flash 3 times.

PATHWAY ILLUMINATION: This feature turns the parking light “ON” for 30 seconds upon a unlock signal and for 10 seconds upon the lock signal TWO STEPS DOOR UNLOCK: This feature will independently unlock the driver’s door only when

disarming the security system. Pushing the

button a second time within 3 seconds will unlock the other doors. AUTOMATIC RE-ARM: If this feature is selected, the security system will automatically re-arm itself in 60 seconds after disarming with remote transmitter. Automatic rearm will cancel if any door is opened before the 60 seconds timer has elapsed.

J. VALET MODE: (System in Disarm or Valet mode)

Activate Valet Mode:

1. Turn the ignition to “Off” position and open any door.

2. Press and hold

3. The door locks will lock and unlock. Release the button

4. The LED will begin to flash every 5 sec. indicating that the system is in valet mode

Exit Valet Mode:

1. Turn ignition 'Off' and open any door.

2. Press and hold

3. The door locks will lock and unlock. Release the button

4. The LED will be off indicating that the system is out of Valet mode.

Remote Door Lock

Remote Door Unlock

K. CAR LOCATOR

Under armed mode, press the button to active car locator function. The siren will chirp 6 times. The parking light will flash 12 times, for you to easily locate your car.

L. PANIC FUNCTION:

The transmitter can be used as a remote panic switch to manually trigger the alarm in case emergency.

1. Press and hold the icon will display on the LCD screen.

2. During panic mode, the normal function of this transmitter button will be suspended.

The transmitter option is installed), however once the

disable device, (where installed) will be enable allowing the vehicle to start.

3. To stop the alarm, press and hold the transmitter or button on the transmitter again for 3 seconds. Also if any transmitter buttons other than

be turned off immediately.

4. If the button is not pressed, the alarm will automatically stop after 30 seconds.

button for 3 second. The alarm will immediately sound and the

and buttons can be used to lock and unlock the door (if the

button is pressed, the vehicle’s starter

or button is pressed and released, the panic mode will

Page 6

M. TRIGGER THE SYSTEM

When armed, your vehicle is protected as follows:

1. Light impact will trigger the warn-away signal.

2. Heavy impacts / Doors open / Hood open / Trunk open / Turn on the ignition key will trigger the

programmed sequence. The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren, horn, parking lights, and dome light will turn on to alerting of an intrusion for 30 seconds. Then it will stop and automatic reset and re-arm. If the one of sensors or detectors still active, the alarm system will sound a maximum of 6 times of 30 seconds cycles.

Hood Trigger

Trunk Trigger

Doors Trigger

Ignition Trigger Warn-away Trigger

Sensor 1 (Zone 4) Trigger

NOISE ABATEMENT CIRCUIT: You system has “Noise Abatement Circuit”. It prevents annoying

repetitive trigger sequences due to faulty door pin switches or environmental condition such as thunder, jackhammers airport noise, etc. Here’s how “Noise Abatement Circuit” works: The alarm triggers five times or ten times for warn-away triggers. Each time, the same sensor (zone 4 or zone 6) is triggering the alarm. “Noise Abatement Circuit” will interpret this pattern of triggers as false alarm. After the fifth trigger (tenth for warn-away), “Noise Abatement Circuit” ignores, or bypasses that sensor until the other sensor or switch is trigger. “Noise Abatement Circuit” covers doors (Hood/Trunk) differently: If the alarm is triggered by an open door for six full cycles, the doors will be bypassed until the trigger ceases.

Sensor 2 (Zone 6) Trigger

Stop The Melody Sound:

alarm the LCD screen will alert user through melody sound and flashing trigger icon, press any button on the LCD remote transceiver to stop melody sound.

While triggering the

N. ANTI CAR- JACKING

Warning: If you don't need the car jacking function in this alarm system, be sure to set car jacking feature

“OFF”. This system is default setting all cars jacking “OFF”.

ACTIVE ANTI CAR JACKING:

1. Press and hold the transmitter while the vehicle’s ignition are ON. The parking lights will turns on for 1.5 seconds to indicate the system enters the car-jacking mode. (A melody sounding from your

Remote LCD transceiver and “ car-jacking mode was activated.)

2. Once the system in car-jacking mode, If you are forced from the vehicle, the system

will be trigger when the door is opened and closed while the ignition is “ON”, the and

PASSIVE ANTI CAR- JACKING:

1. Turn the ignition switch to “ON” position; the system enters the car-jacking mode.

2. Once the system in car-jacking mode, If you are forced from the vehicle, the system will trigger when the door is opened and closed while the ignition is “ON”, the and icon will

display on the LCD screen.

TRIGGER THE ANTI CAR -JACKING MODE:

a). 50 seconds after the system has beer triggered. The siren will start chirping for 15 seconds. b). During this 15 seconds period of chirping, you will be alerting to push the valet switch once to turn off

c). 65 seconds after the system has beer triggered. The siren starts alarming and the parking light starts d). 90 seconds after the system has beer triggered

icon will display on the LCD screen.

the car-jacking feature. If not, it will enter second timer car jacking. flashing.

1. The siren still alarming and the parking light flashing, and

2. The starter disable will activate to prevent the vehicle from starting.

3. It will remain active until the vehicle's battery power exhausted.

and buttons at the same time for 2 seconds

” icon will display on the LCD screen to confirm the

Page 7

OVERRIDE THE SYSTEM TO TURN OFF ANTI CAR- JACKING:

Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch, the siren will stop and the system disarmed

O. SYSTEM’S TRIGGER CHECK (For two-way transceiver operation only)

Press the transceiver button first, within 3 seconds press (C) button. It

responds with one melody sound and all trigger’s records will immediately displayed on the LCD screen.

Note: If it has no responds then you are out of range.

P. SYSTEM’S STATUS CHECK (For two-way transceiver operation only)

When you want to check the system’s present status through the LCD screen, Press the transceiver

one melody sound and all vehicles’ status records will immediately displayed on the LCD screen. Note: If it has no responds then you are out of range.

button twice, within 3 seconds press (C) button. It responds with

Q. DRIVER PAGING / LOSE & FOUND (For two-way transceiver operation only)

It is useful the event that someone wants to page the driver of the parked vehicle or someone cannot find his LCD remote transceiver.

Indoor Driving Paging

Under the ignition switch “off” condition, press and hold the valet switch for 2 seconds to page the driver, one chirp sound shall be emitted from the vehicle and the paging melody sound continues sounding from you Remote LCD transceiver and “

” indication flashes on the LCD screen.

Outdoor Driving Paging

If someone tries to page you by tapping the paging (knock) sensor (optional) which is usually mounted on the bottom part of front window, the paging melody sound continues sounding from you Remote LCD transceiver and “

1. Press the transceiver activate outdoor driver paging function, It responds with chirps of the vehicle, a melody sound and " is on.

2. When tapping the paging (knock) sensor, one chirp sound shall be emitted from the

vehicle and the paging melody sound continues sounding from you Remote LCD

transceiver and “

3. Turn on the ignition switch; OR press the

disarm the system, this outdoor driver paging function will exit.

” indication flashes on the LCD screen.

button first, within 3 seconds press ( ) button to

" indication flashes on the LCD screen to confirm the function

” indication flashes on the LCD screen.

button to arm the system; OR press the button to

R. DOME LIGHT CONVENIENCE DELAY & SUPERVISION

The alarm with a unique feature which will turn on your vehicle dome light as following:

1. Upon disarming, the interior light will remain on for 30 seconds.

2. If the vehicle is intruded, the interior light will flash for the same duration as the siren.

Note: Turn on the ignition switch or arm the alarm will turn off the dome light.

S. IGNITION CONTROL DOOR LOCK/UNLOCK.

If the vehicles door locks have been interfaced to the security system, the system will automatically lock the vehicle's doors when the ignition is turned “ON” and /or unlock the vehicle’s doors when the ignition is turned “OFF”.

T. TRUNK RELEASE (CHANNEL 3) OUTPUT.

Press and hold button on the transmitter for one seconds to remote control the trunk

release or other electric devices.

U. CHANNEL 4 /5 /6 /7 TIMER CONTROL OUTPUT

Activate The Channel 4: Press and buttons at the same time to active Channel 4 function. Activate The Channel 5: Press Activate The Channel 6: Press Activate The Channel 7: Press and buttons at the same time to active Channel 7 function.

The channel output is user-programmable timer output. This timer output may be used to turn on the headlight, power window or sunroof. (Factory defaults setting at momentary output.)

and buttons at the same time to active Channel 5 function.

and buttons at the same time to active Channel 6 function.

Page 8

V. POWER ON MEMONRY:

This security system is equipped with circuitry that will allow the unit to remember its alarm state if the power is lost and then reconnected.

REMOTE START OPERATION:

A. TO REMOTE START THE VEHICLE:

1. Press button twice on the transmitter.

2. The parking light will activate to indicate the remote start received the signal. (A

melody sounding from your Remote LCD transceiver and “ LCD screen to confirm the remote start was activated.)

3. The engine will start approximately 5 seconds.

4. Once the engine is running, after couple seconds the parking light will turn on again

and climate controls will activate and adjust the vehicles interior temperature to your

preset setting. (While the vehicle is running, the “

the LCD screen will flash and it will indicate count down timer based on the 5, 10, 20 or 30 minute run time set up by your installation center.)

5. The vehicle will run for 5 to 30 minute cycle and automatically shut down. (When the

unit shuts off the count down timer will turn off and the transmitter will play a melody.)

Note: The Remote Start Unit will not start the vehicle if any one of the following

conditions exists:

1. The hood is opened.

2. The brake pedal is pressed.

3. Move the optional remote start enable toggle switch to OFF position. (If installed)

4. The gear selector is in any gear other then “PARK” or “NEUTRAL”

” icon and the “minutes” digit on

” icon will flashes on the

Activate Remote Start

Engine Running

B. TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START:

To operate the vehicle while engine running on the remote start.

1. Insert the ignition key and turn it to “ON” (not the start) position.

2. Press the brake pedal.

Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down.

C. TEMPORARY STOP FEATURE:

This feature allows the vehicle to remain running after the key has been removed from the ignition. This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would like to leave the motor running and the climate control on.

1. Before turning off the engine, press the

-- The LED indicator will flash 3 times to confirm enter.

2.Turn the ignition key to OFF position. (The engine will stay running.)

3.The engine will run until the pre-programmed time elapsed or shutdown input is received.

button twice on the transmitter.

D. TURBO TIMER MODE:

Turbo timer mode keeps the engine running after arriving at you destination for a programmable period of 3/ 5 or 10 minutes, This allows the system’s time to conveniently cool down the turbo after you have left the vehicle. To activate:

1. While engine is running, place the transmission gear in the park position and pull up

the hand brake.

2. Before turning off the engine, press and release

time.

-- The parking light will activate to indicate the remote start has entered turbo charge mode. --

3. Pull off the “Ignition Key” from the key cylinder.

-- Engine keeps running. --

4. Exit and secure the vehicle.

-- Engine continues running until the pre-programmed time elapsed. -If you do not want the vehicle to continue to run for one cycle, simply step on the vehicle's brake, or activate the

button in succession. Any of these will cause the engine to turn off.

and buttons at the same

E. TIMER START:

Your system has the ability to automatically start the vehicle every 1,2 or 3 hours, run for the pre-programmed time (5, 10, 20 or 30 minutes), and then shut off. This will continue for 48 hours. This

Page 9

feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. If the system is set up to start in temperature mode, the system can be programmed to automatically start the vehicle engine whenever the temperature inside the vehicle reaches or drops below the preprogrammed temperature level. The system will monitor the air temperature every 3 (2 /1) hour and will only start the engine during extreme cold temperatures. WARNING! Be certain that the vehicle is outdoors before using this or any remote vehicle-starting device. A running engine produces dangerous carbon monoxide fumes, which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if it is garaged.

Timer Start Operation:

1. Turn the ignition key on then off. Within 15 seconds …..

2. Press the

3. The parking lights will flash and the siren will chirp 3 times indicating the timed start mode is activated.

Your set the timer icon or the temperature icon for engine start flashes for approx. 3 seconds on the LCD screen. After 3 seconds

icon stays displayed on the LCD screen

the Daily Timer Start Operation: The feature is very useful for the driver who wants to run the vehicle punctually at the same time next morning. Before set-up of the “Daily Timer Start”, you should set you time for engine start.( see Timer Setting /

1. Turn the ignition key on then off. Within 15 seconds …..

2. Press the seconds.

3. The parking lights will flash and the siren will chirp 6 times indicating the daily timed start mode is activated.

Your set time for the next day engine start flashes for approx. 3 seconds on the LCD screen. After 3 seconds the

Cancel the timer start: To cancel the timer start do one of the following;

1. Start the vehicle manually with the use of the ignition key.

2. Remote starts the vehicle using your keychain RF transmitter.

button first, with 3 seconds press the button.

Timer set-up for “Daily Timer Start, page 16)

button first, with 3 seconds press and hold the button for three

icon stays displayed on the LCD screen.

Timer Start Temperature Start

Daily Timer Start

F. TEMPERATURE CHECK

You can monitor through the LCD screen, the present indoor temperature of the passenger compartment before cooling or heating your vehicle.

Press the transceiver in-door temperature will be shown on the LCD screen. This reading may be higher than actual ambient temperature due to the greenhouse and is relative only the inside vehicle temperature.

button first, within 3 seconds press the ( ) button; the

G. TO TURN OFF THE REMOTE START:

When the engine is running (by remote start), if you want to stop it,

1. Press

2. Move the optional remote start enable toggle switch to OFF position. (If installed)

3. Press the brake pedal. The vehicle will shut down and turn off the parking light to indicate engine stopped.

button twice on the remote transmitter under remote start mode.

H. SHUT-DOWN INPUT FOR REMOTE STARTER:

If any of the following conditions exist while the system is operating, the engine will not start or will shut down immediately:

1. The hood is opened.

2. The brake pedal is pressed.

3. Engine is over-revved. {“Tachometer checking type” only}

4. The pre-programmed run time (5 / 10 /20 / 30 minutes) has elapsed.

5. Press

6. Move the optional remote start enable toggle switch to OFF position. (If installed)

8. The vehicle refused to start running after {3} unsuccessful attempts.

button twice on the remote transmitter under remote start mode.

I. DISABLING THE REMOTE START SYSTEM: (If installed)

This feature allows your system’s remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed area. To disable the remote start, move the optional remote start enable toggle switch to the OFF position.

Page 10

LCD REMOTE CONTROL TRANSCEIVER:

Note: If the system is interfered by stronger radio frequency around, sources of high voltage electric power

or such Obstacles like tall buildings and so on, the transmission range may get shorter as the system uses low out put powered frequency.

A. BATTERY REPLACEMENT:

A 1.5V type AAA Lithium / digital camera use / Alkaline battery powers the Remote Transmitter. When the power of the battery weakens a replaced to new one, there will be beep sounds indicate the power is up and the clock on the LCD screen returns to AM12:00 after displaying all the icons. Correct the time by pressing Note : 1. 1.5V type AAA Lithium battery (highly recommend) / 1.5V type AAA Hi-power battery for digital

camera use (suggest) / 1.5V type AAA Alkaline battery (at least)

2. Press the battery.

button two times when the battery compartment is empty, then insert the new

icon shall be displayed on the LCD screen. When the old battery is

for 3 seconds before using (See Timer Setting).

B. THE REMORE LCD ICONS WITH FUNCTION:

C3 C5

Door Lock

Your vehicle doors are locked

Armed Mode

Your vehicle is in armed mode Car Jack Mode

Activate the car jacking mode

Remote Transmission

You are transmitting the signal to control unit

Hood Trigger Hood is illegally opened (Zone 1)

Door Open Warning Doors are illegally opened (Zone 3)

Ignition Trigger

Ignition switch is illegally turned on (Zone 5)

System Trigger

Engine Cranking

Your vehicle engine Cranking by remote control Timer Control Start Engine start automatically at the same time next day or every 2 / 3-hour.

Activate Channel 3 (Trunk Release). Activate Channel 5

C4 C6

Door Unlock

Your vehicle doors are unlocked and the system is Disarmed

Hidden Alarm Mode

Your vehicle is in armed with hidden alarm mode

Valet Mode

All the function shall be temporarily on hold.

In – Range Indicator

Your are within the remote control range.

Trunk Trigger Trunk is illegally opened (Zone 2)

Sensor Trigger

Trigger on Sensor 1 (Zone 4) or Optional Sensor 2 (Zone 6)

Warn Away Trigger

Warn Away Trigger on Sensor 1 or Optional Sensor 2.

Low Battery

You have to replace the battery of remote control.

Engine Running

Your vehicle's engine is running

Temperature Monitor

Indoor temperature of your vehicle

Activate Channel 4

Activate Channel 6

Page 11

Activate Channel 7 Time Monitor

Count Down Timer

Reminder when time is up for parking

Melody Mode

Remote Control alert user through melody sound

Button Lock

Disable the transmission function temporarily

Alert Alarm

You have set morning call alarm

Power Save Mode

Save the battery power

Vibration Mode

Remote Control vibrates when the system is triggered

Driver paging / Lose and Found Someone is paging you in front of your vehicle

C. PROGRAMMING OF THE LCD REMOTE TRANSMITTER:

Transmitter Button Description Operation

(1 second) LCD screen lamp turns on for

5 seconds.

(3 seconds) Timer Programming Mode. Press and hold for 3 seconds

(5 seconds) Power Save Mode Press and hold for 5 seconds

- -

- (2-second)

- -

(2-second)

- + (2-second)

1. Screen Lamp ON: Press and hold the button one second, with one melody sound and the LCD screen lamp will turns on for 5 seconds

2. Power Save Mode: While the power save mode, the LCD remote transceiver uses “0” current to save the battery power. Entry: Press & hold the

icon on the LCD screen to indicate entry the “power save mode”.

Exit: Press any button of the LCD remote transmitter to exit the “Power Save Mode”.

3. Clear the Flash Icon and Melody Sound: Press the button 3 times within 3 seconds will clear the

flash icon and melody sound on the LCD screen transceiver

4. Stop The Trigger Melody Sound:

melody sound and flashing trigger icon, press any button on the LCD remote transmitter to stop melody sound

5. Button Lock: It is useful if you want to disable the transmission function of the remote control temporarily to prevent from any inadvertent pressing of buttons by others. Press

the activate or cancel the button lock function, the

to show the LCD remote transmitter is on “Button Lock”.

6. Vibration / Melody Mode:

only.

button first, within 3 seconds press and hold the ( ) button for 2 seconds to

Clear the Flash Icon and Melody Sound on the LCD Screen Transmitter

Button Lock ( Melody ( ) / Vibration ( ) Mode Program Count Down Timer

(10-Minute / 20M / 30 M /1Hour /1.5H /

2.0H) Enable / Disable Bi Sound (Bi) While

Pressing Button Illumination On /Off Press within 3 seconds

Switching code for 2nd / 1st Car Operation

button for 5 seconds, with one melody sound and

) enable / disable

( )

While triggering the alarm the LCD screen will alert user through

icon will displayed on the LCD screen

Press and hold for 1 second 1 melody sound to confirm enters.

2-melody sounds to confirm enter.

1 melody sound to confirm enters. Press within 3 seconds

Press within 3 seconds Press within 3 seconds Press within 3 seconds cycling

*leave the buttons starting count down then flashes

Press within 3 seconds

Page 12

It is useful when you are in a noisy place and difficult to hear beep sound from the

remote control as the remote control in this mode, vibrates itself if your security system is triggered.

Press the mode of melody (

displayed on the LCD screen.

7. Enable / Disable Bi Sound While Pressing Button:

It has a short “bi” sound while pressing the button of the LCD screen transceiver If you want mute the “bi” sound mute always while press button. Press the

seconds press and hold the

8. Low Battery Indication:

When the power of the battery weakens, it has two short “bi” sound and flash button of the LCD screen transceiver.

9. Set Up Fixed Count Down Timer:

1. Press the

LCD screen will shows

2. Press the

(ie.0:30)…..and so on.

3. Leave the buttons starting count down then

Note: 1.The count down period is fixed as 10 minutes, 20 minutes, 30 minutes, 1 hour, 1.5 hours and 2 hours maximum.

2.When count down timer showing 0:00 means to turn off the timer.

3. Press

10. Out Of Range Indication:

If this feature is selected, the system will automatically check the range every 30 minutes.

1. If user is within the range, the

2. If user is out of range, it has five short “bi” sounds and the

Note: Programming “Out Of Range Indication” will decrease the life expectancy of battery.

11. Illumination

Illumination for the LCD display can be programmed “On” or “Off”. When programmed “On”, the LCD will illuminate every time the remote control receives a page or transmits a command.

Press the beep once for “On”, twice for “Off” and the light will turn on/off with each press.

Note: Programming “illumination “On” will decrease the life expectancy of battery.

12. Second Vehicle Security Operation:

Your remote transmitter can be utilized to control a second vehicle security system, To program the remote control transmitter to a second vehicle, follow the instructions for Transmitter programming. All programming parameters be the same except for the following:

button first, within 3 seconds press and hold the button to select the

) / vibration ( ) or melody with vibration ( ) , the / icon will

button first, within 3

(Bi) button for 2 seconds to disable the “bi” sound.

icon while pressing the

button first, within 3 seconds press and hold the ( ) button for 2 seconds, the

icon and timer (ie. 0:10) ,

( ) button again showing next order time on the screen ( ie.0:20), press them again

icon flashes

button for real time indication when the timer is counting down.

icon will display on the LCD screen.

icon will disappear on the LCD screen.

button twice, within 3 seconds press and hold the button for 2 seconds. The remote will

For 1-way Remote Control Transceiver:

1. Press the button first within 3 seconds press and hold and buttons at the same time for 2 seconds

2. Once button is pressed, the LED on the transmitter will illuminate for 3 sec. to indicate second vehicle transmitter operation.

3. While the LED is illuminated, press any button on the transmitter to control the 2nd car security system or alarm function (arm/ disarm/ trunk/ remote start)

Note: Button functions are the same for the second car as they are for the first car.

For 2-way LCD Remote Control Transceiver:

2nd Car Operation: you can remote control and communicate with a second vehicle security system.

1. Press with two beeping sound and the “

indicate the second transceiver pin code has built-in.

2. While the “ communicate with a second vehicle security system. It has two short “bi” sounds while pressing the button of the LCD screen transceiver.

Back to 1st Car Operation:

first, within 3 seconds press and hold and buttons at the same time for 2 seconds

” icon will display on the LCD screen to

” icon display on the LCD screen, you can remote control and

Page 13

1. Press for 2 seconds with one long beeping sound and the “ the LCD screen to indicate the system is back to first transceiver pin code.

2. While the “ and communicate with a first vehicle security system. It has one short “bi” sound while pressing the button of the LCD screen transceiver.

first, within 3 seconds press and hold and buttons at the same time

” timer icon will display on

” timer icon display on the LCD screen, you can remote control

D. TIMER SETTING:

Transceiver Button Description Press Transceiver Button 1 Press & Hold the

button for 3 seconds

Press the button once Time setting (Minute) 2 Press the button once. Press the button once Alert Alarm Time Setting (Minute)

Press the button once Alert Alarm Setting ON / OFF for OFF and for ON

3 Press the button once

Press the button once Count down Timer Setting (Minute)

Press the button once Count down Timer Setting ON / OFF for OFF and for ON

Press & hold the for 2 seconds.

EXIT: Press and hold the button for 2 seconds or leave it for 10seconds, the system will exit the

programming mode.

1. Timer Setting: Example to AM10:30

1. Press & hold the adjusting.

2. Press the

3. Press the button once again then the “Minute” digit flashes for adjusting.

4. Press the

5. Press the button for 2 seconds with one-melody sound to confirm exit the timer program mode.

2. Alert Alarm Timer Setting: Example to PM 6:30

1. Press & hold the adjusting.

2. Press the adjusting.

3. Press the

4. Press the button once again then the “Minutes” digit flashes for adjusting.

5. Press the

6. Press the

7. Press the Press the button to stop the “Alert Alarm Timer”, and the “OFF” icon will show on the LCD screen.

8. Press button for 2 seconds with one-melody sound to confirm exit the timer program mode.

3. Count Down Timer Setting: Example Set count down timer at 2:30

1. Press & hold the adjusting.

2. Press the adjusting.

3.Press the

4.Press the button once again then the “Minutes” digit flashes for adjusting.

5. Press the

6. Press the

7. Press the button to start the count down timer, and the “ON” icon will show on the LCD screen. Press the button to stop the count down timer, and the “OFF” icon will show on the LCD screen.

8. Press the button for 2 seconds with one-melody sound to confirm exit the timer program mode.

or button to decrease or increase the “Hour” digit until AM10:xx or button to decrease or increase the “Minutes” digit until AM 10:30

button twice, the LCD screen will shows icon and “Hours” digit is flashes for or button to decrease or increase the “Hour” digit until PM 6:xx or button to decrease or increase the “Minutes” digit until PM 6:30

button once again then icon flashes for alert alarm “ON / OFF” setting

button to start the “Alert Alarm Timer”, and the “ON” icon will show on the LCD screen.

button 5 times, the LCD screen will shows icon and “Hours” digit is flashes for

or button to decrease or increase the “Hour” digit until 2:xx

or button to decrease or increase the “Minute” digit until 2:30

button once again then icon flashes for alert alarm “ON / OFF” setting

button

button for 3 seconds, with two-melody sound and the “Hours” digit flashes for

Timer Setting (Hour) *Flash digit for adjusting

*Flash digit for adjusting Alert Alarm Time Setting (Hour) *Flash digit for adjusting

*Flash digit for adjusting

Count Down Timer Setting (Hour) *Flash digit for adjusting (Max.19 hours 59 minutes)

*Flash digit for adjusting

Daily Timer Start Timer Setting Flash

adjusting

/ icon and “Hours” for

for – and for + for – and for + for – and for + for – and for +

for – and for + for – and for +

for – and for +

Page 14

Note: Maximum is 19 hours.

4. Time Set-Up For “Daily Timer Start”: Example to AM 6:30

1. Press & hold the adjusting.

2. Press & hold the digit for Hour set-up.

3. Press the

4. Press the button once again then the minute digit flashes.

5. Press the

6. Press the button for 2 seconds with one-melody sound to confirm exit the timer program mode.

or button to decrease or increase the hour digit until AM 6:00 or button to decrease or increase the minutes digit until AM 6:30

button for 3 seconds, with two-melody sound and the “Hours” digit flashes for

button for 2 seconds, the LCD screen will flash / icon and “Hours”

A. PROGRAMMING THE REMOTE TRANSMITTER:

Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is exceeded, the security system will start deleting transmitters from memory in chronological order.

1. Turn the Ignition 'switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds.

2. Push the Valet switch 3 times and holding in on 3rd push until a long chirp is hearing then release the valet switch. You are now in the Transmitter programming mode.

3. Press and hold any button of the transmitter until the siren responds with a confirming chirp, indicating the signal has been stored into memory.

4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each transmitter.

Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds to exit the program mode and the siren will

chirp three long chirps.

B. FEATURES PROGRAMMING:

ALARM FEATURE “I” PRORAMMING:

1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.

2. Push the Valet switch 2 times and holding in on 2

release the valet switch. You are now in the Alarm feature ‘I’ programming mode.

3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.

a. The siren chirps and LED pause will indicate previously setting. b. The factory default settings is always [1] LED flash, [1] chirp.

4 Depress the transmitter button ‘A’ again to change the feature. Simple keep re-depressing the

transmitter button ‘A’ again until the module advances to your desired setting.

a. In this case, Press button ‘A’ again, the module would advance to [2] LED flash, [2] chirps. b. Press button ‘A’ again, the module would advance to [3] LED flash, [3] chirps etc.

5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you wants to program.

Press Transmitter Button

5 +

One Chirp / LED one pulse

Factory Default Setting

All Siren/Horn

arming, disarming

and tamper

indicator chirps on

Active arming Passive arming

Automatic Rearm off Instantly Door Ajar Warning Without Car-jack mode Panic with Ignition off

Two Chirps / LED two pulses

Siren/Horn arming Chirps OFF w/second TX button push confirmation, Disarm chirp OFF. All tamper indicator chirps ON

without passive door locking Automatic Rearm on

45 seconds delay Door Ajar Warning. Active Car-jack mode Passive Car-jack

Panic with Ignition on & off

push until one chirp with a long chirp is hearing then

Three Chirps / LED three pulses

All Siren/Horn arming, disarming and tamper indicator chirps off

Passive arming with passive door locking.

mode Panic with Ignition on & off. Panic with No time limit.

Four Chirps / LED four pulses

Siren/Horn arming and disarming chirps off with all tamper indicator chirps on

Without Panic function.

Page 15

Horn output for alarm

trigger, panic and

car- finder only

“SOS” type

S-S-S - L-L-L - S-S-S Six Chirps / LED six pulses

S-L-S-L S-S-S - L

7 +

8 +

Standard Horn

output Function

Standard horn

pulse Five Chirps / LED five pulses

S-M-L-S-M-L S-S - L - S-S

Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds to exit the program mode and the siren will

chirp three long chirps.

ALARM FEATURE “II” PRORAMMING:

1 Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2 Push the Valet switch 4 times and holding in on the 4

then release the valet switch. You are now in the Alarm feature ‘II’ programming mode.

3 Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program. Press T

ransmitte

Button

3 Pathway illumination

4 Horn Chirp

One Chirp / LED one pulse

Factory Default Setting

0.8 second door lock & unlock

Five Chirps = 0.8 second Lock, double 0.8 second. Unlock Six Chirps = Double 0.8 second Lock, 0.8 second Unlock Seven Chirps = Door lock with “Comfort Feature”

Ignition controlled door locks & unlocks

feature “off”

Output16 mS The Vehicle without Turbo Timer mode

Enable the out of range check

Two Chirps / LED two pulses

3.5 second door lock & Unlock

Ignition controlled door locks only

Parking light turns “on” for 30- second upon an unlock signal

Horn Chirp Output 30 mS

Press buttons at the same time to control Engine running three minute. Disable the out of range check.

and

push until two chirps with a long chirp is hearing

Three Chirps / LED three pulses

0.8 second Lock,

0.35 second Unlock

Ignition controlled door unlocks only

Parking light turns “on” for 30- second upon an unlock signal & 10-second upon a lock signal. Horn Chirp Output40 mS

Press buttons at the same time to control Engine running five minutes

and

Four Chirps / LED four pulses

0.8 sec. dbl Lock,

0.8 sec. dbl Unlock

Without ignition controlled door locks & unlocks

Horn Chirp Output10 mS

Press buttons at the same time to control Engine running ten minutes

and

Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds to exit the program mode and the siren will

chirp three long chirps.

Comfort Feature:

Some Vehicles have a special “COMFORT feature”. When you lock the door with the key, you just have to

keep on turning the key on the door about 5 or 7 seconds and the window will close directly.

If your vehicle with “COMFORT feature” and you wish the door being locked and the window being closed automatically at the same time by remote control, you can set the alarm feature II-1 “with comfort feature

ALARM FEATURE “III” PRORAMMING:

1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.

2 Push the Valet switch 6 times and holding in on the 6

hearing then release the valet switch. You are now in the Alarm feature ‘III’ programming mode.

3 Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program. Press T

ransmitte

Button

One Chirp / LED one pulse

Factory Default Setting

Two Chirps / LED two pulses

push until three chirps with a long chirp is

Three Chirps / LED three pulses

Four Chirps / LED four pulses

Page 16

H1/6 Pink Wire =

Ignition 2 on during Crank

6 +

7 +

H11/5 Brown Wire = Constant Siren output H3/9 White / Blue Wire = 1 pulse activate H4/4 White / Yellow Wire Disarm Signal Output = One Pulse Output H3/13 Yellow Wire = Ignition 3 on during Crank H3/17 Black / Green Wire Channel 4 Output = 1 pulse output

FIVE Chirps= Output for 30 sec. H3/18 Black / Red Wire Channel 5 Output = 1 pulse output

H1/6 Pink Wire = Ignition 2 off during Crank H11/5 Brown Wire = 5-second pulse Siren output H3/9 White / Blue Wire = 2 pulse activate H4/4 White / Yellow Wire Disarm Signal Output = Same as Door Unlock Output H3/13 Yellow Wire = Ignition 3 off during Crank H3/17 Black / Green Wire Channel 4 Output = Latched output until IGN ON

H3/18 Black / Red Wire Channel 5 Output = Latched output until IGN ON

H1/6 Pink Wire = Ignition 2 same as accessory H10/5 Brown Wire =

H3/13 Yellow Wire = same as accessory

H3/17 Black / Green Wire Channel 4 Output = As long as TX button is held

H3/18 Black / Red Wire Channel 5 Output = As long as TX button is held

Horn Output

H3/17 Black / Green Wire Channel 4 Output = Output for 15-sec.

H3/18 Black / Red Wire Channel 5 Output = Output for 15-sec

8 +

*9 +

FIVE Chirps= Output for 30 sec. H3/19 Black / Violet

Wire Channel 6 Output = 1 pulse output

FIVE Chirps= Output for 30 sec. H3/20 Black /

Yellow Wire Channel 7 Output = 1 pulse output

FIVE Chirps= Output for 30 sec.

H3/19 Black / Violet Wire Channel 6 Output = Latched output until IGN ON

H3/20 Black / Yellow Wire Channel 7 Output = Latched output until IGN ON

H3/19 Black / Violet Wire Channel 6 Output = As long as TX button is held

H3/20 Black / Yellow Wire Channel 7 Output = As long as TX button is held

H3/19 Black / Violet Wire Channel 6 Output = Output for 15-sec

H3/20 Black / Yellow Wire Channel 7 Output = Output for 15-sec

Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds to exit the program mode and the siren will

chirp three long chirps.

REMOTE START FEATURE PROGRAM MODE.

START FEATURE “I” PRORAMMING:

1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.

2. Push the Valet switch 8 times and holding in on the 8 then release the valet switch. You are now in the Start feature ‘I’ programming mode.

3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.

Press T

ransmitte

Button

One Chirp / LED one pulse

Factory Default Setting

Gasoline Engine

Two Chirps / LED two pulse

push until four chirps with a long chirp is hearing

Three Chirps / LED three pulse

Four Chirps / LED four pulse

Page 17

Diesel Engine with Wait-To-Start Light (H3/9 White/Green wire must be connected)

Five Chirps/ 30 seconds warn-up timer for Diesel Engine

10 seconds warn-up timer for Diesel Engine

Six Chirps/ 45 seconds warn-up timer for Diesel Engine

15 seconds warn-up timer for Diesel Engine

20 seconds warn-up timer for Diesel Engine

2 10 minutes run time 20 minutes run time 30 minutes run time 5 minutes run time

Factory alarm

Without this feature disarm with channel 3 on

Flashing parking light output

Door lock before start

Constant parking

light output

Door lock after

shut-down

Door lock before

Without this feature start and Door lock after shut-down

8 +

3 Hour Time start 2 Hour Time Start 1 Hour Time Start Temperature-Contro

l Start OFF Fahrenheit display for temperature

Temperature-Contro l Start 5F (-15C) Celsius display for temperature

Temperature-Contro l Start – 4F (-20C)

Temperature-Contro

l Start – 22F(-30C)

Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds to exit the program mode and the siren will

chirp three long chirps.

START FEATURE “II” PRORAMMING:

1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.

2. Push the Valet switch 10 times and holding in on the 10 hearing then release the valet switch. You are now in the Start feature ‘II’ programming mode.

3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.

Press T

ransmitte

Button

One Chirp / LED one pulse

Factory Default

Two Chirps / LED two pulse

Setting

Exit the programming mode.

Engine Checking Voltage

Engine Checking

TACH..

RPM learning Start Timer:

0.6-second

0.8-second (2 chirps), 1.0-second (3 chirps), 1.2-second (4 chirps),

1.4-second (5 chirps), 1.6-second (6 chirps), 1.8-second (7 chirps),

2.0-second (8 chirps), 3.0-second (9 chirps), 4.0-second (10

chirps),

5 6 +

Hi check level Low check level

Start or Stop the system for TESTING & ADJUSTMENT Test Mode for

Trigger input

Test Mode for

Sensor 1 / Shock

Sensor (Zone 4).

push until five chirps with a long chirp is

Three Chirps / LED three pulse

Engine Checking

Four Chirps / LED four pulse

OFF

Test Mode for Optional Sensor 2 (Zone 6)

Exit: Press the button to exit the program mode and the siren will chirp three long chirps.

ENGINE CHECKING TACH. / RPM LEARNING

Important Note: You must program the “Tach Signal” before trying to remote start.

1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.

2. Push the Valet switch 10 times and holding in on the 10 hearing then release the valet switch.

3. Press

and buttons at the same time once to set the “Engine Checking TACH.” One chirp

confirms this setting.

4. Press the

button once, one chirp to indicate the system in features “RPM Learning mode”.

5. Start the vehicle with the key.

push until five chirps with a long chirp is

Page 18

-- While the engine is running, the parking light & LED will flash, If don’t, please check tach. wire connection. (H3/7 White/Red) --

6. Press and hold the valet switch for 2 seconds until a long chirp. The RPM signal is learned.

7. Turns off the ignition switch to stop engine running. Once you complete step 7, you can adjust and test “Check Level” as below:

CHECK LEVEL PROGRAMMING: (TEST and ADJUST)

1. Press the button twice to start the vehicle.

2. If everything goes well: a. Press the button twice to stop engine running. You have been completed this programming

successfully.

b. Press

button once to exit the program mode and the siren will chirp three long chirps.

3. If the crank time is too short, -- The engine did not successfully run before the starter quit cranking --:

a. Press the button twice on the transmitter to stop engine running.

b. Press button to set proper “Check Level ” to Hi position. Two chirps confirm this setting.

c. Repeat the step1 – 4.

4. If the crank time is too long, -- Engine is successfully running, while the starter is still cranking --:

a. Press the button twice on the transmitter to stop engine running.

b. Press button to set proper “ Check Level ” to Low position. One chirp confirm this setting

c. Repeat the step1 – 4.

ENGINE CHECKING VOLTAGE

Important Note: The voltage “Check Level” for most vehicles would be set in “Hi Check Level”, while in

“Engine Check Voltage” mode, the “Check Level” must be set at “HI” position first.

1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.

2. Push the Valet switch 10 times and holding in on the 10

push until five chirps with a long chirp is

hearing then release the valet switch.

3. Press

and buttons at the same time twice to set the “Engine Checking Voltage”. Two chirps

confirm this setting.

4. Press

button twice to set “Check Level” to “HI” position. Two chirps confirm this setting.

Once you complete step 4, you can adjust and test “Start Timer” as below:

START TIMER PROGRAMMING: (TEST and ADJUST)

1. Press the button twice on the transmitter to start the vehicle.

2. If everything go well, Wait for 20 seconds: a. If the engine still running.

I. Press the button twice to stop engine running. You have been completed this programming

successfully.

II. Press

button once to exit the program mode and the siren will chirp three long chirps.

b. If the engine shut down after the vehicle has been started.

I. Press the II. Press

button twice to stop engine running.

button once to set “Check Level” to “LOW” position. One chirp confirm this setting

III. Repeat the step1 – 2.

3. If the crank time is too long. -- Engine is successfully running, while the starter is still cranking --:

a. Press the button twice to stop engine running. b. Press

button to set proper “Start Timer”. The chirp will confirm these enter.

-- Decrease “Start Timer” is necessary. --

c. Repeat the step1 – 4.

4. If the crank time is too short. -- The engine did not successfully run before the starter quit cranking --:

a. Press the button twice to stop engine running. b. Press

button to set proper “Start Timer”. The chirp will confirm these enter.

-- Increase “Start Timer ” is necessary.--

c. Repeat the step1 – 4.

ENGINE CHECKING OFF

1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.

2. Push the Valet switch 10 times and holding in on the 10

hearing then release the valet switch.

3. Press

and buttons together three times to set the “Engine Checking Off”. Three chirps confirm

this setting.

Once you complete step 3, you can adjust and test “Start Timer” as below:

START TIMER PROGRAMMING: (TEST and ADJUST)

1. Press the button twice on the transmitter to start the vehicle.

2. If everything goes well:

push until five chirps with a long chirp is

Page 19

a. Press the

button twice to stop engine running. You have been completed this programming

successfully.

b. Press button once to exit the program mode and the siren will chirp three long chirps.

3. If the crank time is too long. -- (Engine is successfully running, while the starter is still cranking --: a. Press the button twice to stop engine running.

b. Press the

button to set proper “Start Timer”. The chirp will confirm these enter.

-- Decrease “Start Timer” is necessary --

c. Repeat the step1 – 4.

4. If the crank time is too short. -- The engine did not successfully run before the starter quit cranking --: a. Press the button twice to stop engine running.

b. Press

button to set proper “Start Timer”. The chirp will confirm these enter.

-- Increase “Start Timer ” is necessary --

Repeat the step1 – 4.

RETURN TO FACTORY DEFAULT SETTING:

1. Turn the ignition ON then OFF 3 TIMES and stay in OFF position.

2. Push the Valet switch 12 times and holding in on the 12

then release the valet switch. You are now in the “Return To Factory Default Setting” programming mode.

ALARM FEATURE ALL RETURNS TO FACTORY DEFAULT SETTING:

3. Press and hold the

and buttons at the same time for 5 seconds, there will be a confirmation six

chirp with 3 long chirp to confirm the system “Alarm Feature I & II & III Programming all returns to factory default setting.

START FEATURE ALL RETURNS TO FACTORY DEFAULT SETTING:

4. Press the

first, within 3 seconds press and hold the and buttons at the same time for 5

seconds, there will be a confirmation six chirp with 3 long chirp to confirm the system “Start Feature I & II Programming all returns to factory default setting.

push until six chirp with a long chirp is hearing

TEST MODE

In this test mode, this system can test the all of the trigger input. The installer can save time to test the sensitivity of the 2-stage shock sensor and optional sensor without using the traditional arming/disarming procedures to test the sensors.

Enter:

1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.

2. Push the Valet switch 10 times and holding in on the 10

hearing then release the valet switch. You are now in the Start feature ‘II’ programming mode.

a. Test the Trigger Input:

Press and release

and buttons at the same time once. One chirp to indicate you are in test

mode.

Trigger sensor Siren short chirps Zone 1 / Hood trigger (H3/4 White/ Black wire) 1 Zone 2 / Trunk trigger (H3/1 Blue wire) 2 Zone 3 / Door trigger (H3/2 Green or H3/3 Violet wire) 3

b. Test the Sensor 1 / Shock Sensor (Connected to H7 4 Pin Plug):

Press and release

and buttons at the same twice. Two chirps to indicate you are in the shock

sensor (connected to H7 4 pin plug) test mode.

1. Activate the warn-away (first stage of the shock sensor); system will emit a short chirp.

2. Activate the full alarm (second stage of the shock sensor); system will emit a long chirp.

3. Continue to test the shock sensor until reach the proper sensitivity.

c. Test the Optional Sensor 2 (Connected to H6 4 Pin Plug):

Press and release the transmitter

and buttons together three times. Three chirps to indicate you

are in the optional sensor (connected to H6 4 pin plug) test mode.

1. Activate the warn-away (first stage of the optional sensor); system will emit a short chirp.

2. Activate the full alarm (second stage of the optional sensor); system will emit a long chirp.

3. Continue to test the optional sensor until reach the proper sensitivity.

Exit: While in test mode, turns the ignition on or press any button to exit the test mode.

push until five chirps with a long chirp is

Page 20

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or an experienced radio/TV technician for help.

FCC Caution :To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices).

FCC Radiation Exposure Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept

any interference received, including interference that may cause undesired operation.

To satisfy FCC RF exposure compliance requirements, this device should be used in hand-held, hand-operated configurations only. The device and its antenna must maintain a separation distance of 20cm or more from a person’s body, except for the hand and wrists, to satisfy RF exposure compliance.

This device is designed to be used in a person’s hands and its operating configurations do not support normal transmissions while it is carried in pockets or holsters next tot a person’s body.