PROGRAMMABLE OPTIONS
You can program multiple options in one session if you start with the lowest option and continue
on to higher options [if needed] without repeating steps #1-3 below. For example, you can follow
the programming steps to change Option #2 to “OFF” by pressing the lock button on the remote,
then you can continue pressing the program button additional times to get to a high number option
and change the setting without having to repeat Steps 1-5. You can only go from low to higher
option numbers in one session.
To Engage Option Programming:
1. Open hood (ground the Blue wire if no hood pin switch is installed)
2. Turn Key to the ON position
3. Press program / valet button 5 times, after a few seconds the unit will flash the
lights 5 times.
4. Push the valet/program button [again] the number of times that corresponds to
the option number desired (1 thru 20). You must get a light flash after each
button press. See chart on next page for option list.
5. When you reach the desired programming level, Press button #1, #2, #3 or #4 to
change the option.
6. Turn Ignition OFF, Close hood and check for changed features. Change each
option individually repeating #1-5.
PROGRAMMABLE OPTION RESET
This system provides a reset method to restore all options to FACTORY DEFAULT
VALUES as listed in the “Button #2” column of the programmable option chart on
pages 18-19. This can be helpful if you have lost track of the option settings on
your system, or when you are moving the system from car to car and want a “clean
slate”.
1. Open hood (ground the Blue Hood Switch Wire if no hood pin is installed)
2. Turn Key to the ON position
3. Press program / valet button 5 times, after a few seconds the unit will flash the
lights 5 times.
4. Push the valet/program button 25 times. Press carefully, do not lose count! You
must get a light flash each time you press the button. If the unit didn’t flash the
lights, then the system did not register your press.
PROGRAMMABLE OPTION TABLE
Option # CS-2205 Alarm
Function
1 Horn Pulse
2
3
4 Active Re-Arm ON *OFF
5 Passive Locks ON *OFF
6
7
Auto lock with
Ignition
Passive/Active
Arming
Parking Lights
on w/Disarm
Arm with
Ignition ON
TX Button #1 TX Button #2 TX Button #3 TX Button #4
Door & Hood
Trigger Only
OFF
ON = Passive Arm *OFF = Active Arm
OFF *ON
OFF
*All Functions
*ON =
Lock/Unlock
*ON (Sensors off
with Ignition On)
No Warn-A-
Way
Lock Only Unlock Only
ON
(Sensors on
with Ignition
ON)
No Arm/Disarm
Pulse
8
9
10
11
12
13
14
Siren Chirps
with Arm/Disarm
Override PIN
Code
Disarm on Trunk
pop
Open Door
Warning
Lock/Unlock
Pulse
Double Unlock
Pulse
Carjack
Enable/Disable
OFF *ON
ON *OFF
OFF *ON
5 seconds *60 seconds
3.5 Sec. *0.80 Sec. 0.50 Sec. Comfort Feature
ON *OFF
ON *OFF
15
16
17 "TEST MODE" Zone 2 & 3 *OFF Zone 1 & 4
18 Panic Mode OFF *ON
19 Aux Channel #1 Latched *Momentary
20 Aux Channel #2 Latched *Momentary
21 Aux Channel #3 Latched *Momentary
22 Aux Channel #4 Latched *Momentary
23
Type of Carjack
Protection
Enable Range
Check
Option Reset to
Default (*)
Values
PASSIVE ACTIVE* FULL-TIME
ON *OFF
With Ignition
Off
Reset with
Ignition ON
Reset with
Ignition ON
Reset with
Ignition ON
Reset with
Ignition ON
Reset options
Timed 1 to120
Timed 1 to120
Timed 1 to120
Timed 1 to120
Sec.
Sec.
Sec.
Sec.
TRANSCEIVER / REMOTE CONTROL PROGRAMMING
1. Turn key to the ON position.
2. Press Programming button 4 times, then after a few seconds the unit will flash
the parking lights 4 times.
Press buttons #1 (Lock) & #2 (Unlock) together at the same time of each transceiver
to be learned. You should get 2 light flashes indication the unit is waiting for a 2
code, then press button #1 & #2 of a second transmitter or transceiver, the unit will
flash 3 times indicating its waiting for the 3
rd
code and lights will flash 4 times for 4th
code. If all 4 codes are learned, the unit will automatically exit code learning mode.
nd
(BLUE WIRE GROUNDED)
2-WAY SYSTEMS &
"SideKick" REMOTES
IGN
OFF
WAIT FOR
4 FLASHES
PRESS 4X's
LOCK &
UNLOCK
PRESS TOGETHER
FLASH 2, 3, or 4 X's
IGN
OFF
COMPLETE
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions.
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that
may cause undesired operation.
Per FCC 15.21, you are cautioned that changes or modifications not expressly
approved by the part responsible for compliance could void the user’s authority to
operate the equipment.
Loading...