Advance Security RS-777 Users Manual

Download

Page 1

2013/05/29

MODEL NO. RS-777

REMOTE ENGINE STARTER

WITH ALARM SYSTEM

OWNER’S MANUAL

RS-777 OP REV 1D

Page 2

2013/05/29

LCD REMOTE CONTROL TRANSCEIVER

A. BATTERY REPLACEMENT:

This system needs no specific maintenance beyond remote control battery replacement. The 2-way remote is powered by a 1.5V AAA battery. The 1-way remote is powered by a 3V, CR2032 battery

Battery Level Indicator (2-way remote)

The Battery Level indicator has three level indicators that serve as a visual indication of battery charge. When the battery reaches a low charge level that requires replacement, the remote control will generate a single notification chirp, and the Battery Level indicator will flash continuously. Gently pull the end of the battery door away from the top of the remote control then slide the door up to expose the battery and remove the expired battery. Place the new battery into the remote. When power is returned the remote control will display all icons in the LCD and generate all beeper tones once. Press any button on the remote to terminate the beeper tone review.

B. STANDARD LCD ICON CONFIGURATIONS:

The lock icon will be displayed when the door locked.

Valet Mode

Remote start and alarm functions shall be temporarily on hold.

Hood Trigger

Hood is illegally opened (Zone 1)

Door Open Warning

Doors are illegally opened (Zone 3)

Ignition Trigger

Ignition switch is illegally turned on (Zone 5)

Remote Transmission

You are transmitting the signal to control unit

Anti Car-Jack Mode

Activate the anti car-jacking mode

Engine Cranking

Your vehicle engine Cranking by remote control

The unlock icon will be displayed when the door unlock

Hidden Alarm Mode The security system arm with hidden alarm function

Trunk Trigger

Trunk is illegally opened (Zone 2)

Sensor Trigger

Trigger on Sensor 1 (Zone 4)

System trigger

In – Range Indicator

Your are within the remote control range.

2nd Car Operation

Engine Running

Your vehicle's engine is running

RS-777 OP REV 1D

Page 3

2013/05/29

tart Memorizing for the car

PASS 1

12:00

0:10 P

Timer Control Start

Engine start automatically every 2 or 3 hours.

Sensor Bypass

Sensor 1bypass under Arm mode

Manual Gear

Engine S with manual gear was set up

Activate Channel 3

Time Monitor

Parking Meter

Reminder when time is up for parking

12:00

Daily Start

Engine start automatically at the same time next day

Turbo Timer

Turbo timer was set up

Activate Channel 3 (Trunk Release).

Activate Channel 4

Alarm Clock

You have set morning call alarm

Low Battery

You have to replace the battery of remote control.

Melody Mode

Remote Control alert user through melody sound

Vibration Mode

Remote Control vibrates when the system is triggered

C. 2-way LCD REMOTE CONTROL TRANSCEIVER OPERATION:

Table 1: Enter : Press & hold “ F “ button until one beep, release F-button and continue press

F button within 5 sec. to move forward to feature option you want to program.

EXIT: Press & hold " F " button for 2 sec. or do nothing wait for 5 sec. automatic exit

2-way LCD (1 beep) => Confirm Exit.

Button LCD Display Button Press and hold the Button until 1 beeps sound Press F Button 2nd time (HHU 1 beep) within 5 seconds Press F Button 3rd time (HHU 1 beep) within 5 seconds Press F Button 4th time (HHU 1 beep) within 5 seconds

SENSOR BYPASS

PASS 1 icon On

HIDDEN ALARM

icon On

ANTI- HIJACK

icon On

and

CH 4 flashing

and

Press button Enable to arm the alarm and bypass sensor 1.

Press button Enable to arm system and with Hidden Alarm Function. Under ignition in "on" position Press

button Enable to activate anti car jacking functions. Press button Enable CH#4 output

Note :

Press and release F Button 2-way LCD Backlight turns on for 5 seconds

Table 2 : Enter : Press & hold “ F “ button until 2 beeps heard, release F-button.

Continue press F button within 5 sec. to move forward to feature option you want to program.

EXIT: Press & hold " F " button for 2 sec. or do nothing wait for 5 sec. automatic exit

2-way LCD (1 beep) => Confirm Exit.

Button LCD display Button

RS-777 OP REV 1D

Page 4

2013/05/29

Press and hold the Button until 2 beeps sounded Press F Button 2nd time (HHU 1 beep) within 5 seconds Press F Button 3rd times (HHU 1 beep) within 5 seconds Press F Button 4th times (HHU 1 beep) within 5 seconds Press F Button 5th time (HHU 1 beep) within 5 seconds

flashing Press button to enter 2-way

STATUS CHECK

ALARM CHECK

VOLTS

TEMP

CHECK

HHU menu mode

Press button Enable to check the vehicle’s status.

Press button Enable to check vehicle’s trigger status.

Press button Enable to check vehicle’s Voltage.

Press button Enable to check temp. status

Table 4 : Return 2-way HHU to default setting

Enter : Press & hold “ F “ button until 4 beeps heard, release F-button.

EXIT: Press & release " F " button or do nothing wait for 5 sec. automatic exit

2-way LCD (1 beep) => Confirm Exit.

Button LCD display Button Press and hold the F Button until 4 beeps sounded

D. PROGRAMMING 2-way LCD HHU (

Enter:

1. Press and hold F button until 2 beeps heard then release the F button.

2. The Matrix show MENU flash, press button to enter HHU menu mode. (LCD display show Hours of current time set up, set up hour(s) first.)

3. Press button to increase value, or Enable the selected feature.

4. Press button to decrease value, or Disable the selected feature .

5. Press button to confirm its selection, move to the next option.

EXIT: Press & hold " F " button or do nothing wait for 15 sec. automatic exit

2-way LCD (1 beep) => Confirm Exit.

Order Menu Option LCD display Functions

1 Current time set

2 Alarm Clock set

Adjust clock hours from 0 to 12

Adjust clock minutes from 0 to 59

RESET

12 is flashing

12: 00

00 is flashing

flashing Press & hold button for 2

seconds to back to default setting and 1 chip for confirm

Select and Adjusting Table-2-Menu options):

Default is 12:00

: 00

Press button = (+) or Press button = (-) Press button confirm its selection, move to next option.

Default is OFF

RS-777 OP REV 1D

Page 5

2013/05/29

3 Parking Meter

4 Power Save Default is OFF

Adjust Alarm Clock hours from 0 to 12

Adjust Alarm Clock minutes from 0 to 59

Select Alarm Clock Enable or Disable

countdown

Adjust Parking Meter countdown hours from 0 to 2

Adjust Parking Meter countdown minutes from 0 to

59. Select Parking

meter countdown Enable or Disable

Select Power Save Enable or Disable

:00

12 is flashing

12: 00 00 is flashing

+ or

OFF

PARK METER Default is OFF

:00 P

0 is flashing

0 :

30 P

30 is flashing

P-- ON

+ or

P -- OFF

+ or

Press button = (+) or Press button = (-) Press button confirm its selection, move to next option.

Press button = Enable or Press button = Disable Press button confirm its selection, move to next option.

Press button = (+) or Press button = (-) Press button confirm its selection, move to next option.

Press button = Enable or Press button = Disable Press button confirm its selection, move to next option. There is a beep sound at 5 min. before Parking countdown reach 0.

Press button = Enable or Press button = Disable

When power save enable, the LCD remote

transceiver uses “0” current to save the battery power. LCD show “Save” on text area

Exit: Press any button of the LCD remote

transmitter to exit the “Power Save Mode”. Press button confirm its selection, move to next option.

RS-777 OP REV 1D

Page 6

2013/05/29

Melody or Vibration

5 2-way HHU

Response mode

Select 2-way HHU confirmation by

Second Car Security Option Car Select CAR 1 or

(Time adjust for Daily Start mode) 1 -12 12 : 00

0 - 59 12 : 00

VIBRO

VIBRO BZ+VIB

CAR SELECT

CAR 2 ( II icon On)

12 is flashing

00 is flashing

+ or

+ +

icon flashing

Default is Buzzer

Press button = Melody or Press button = Vibration Press button confirm its selected, move to next option.

Default is CAR 1

- CAR 1 operation.

- CAR 2 operation (II icon On mean 2nd car

operation). Default is OFF

- Program Daily start hour Press button = (+) hours increase or Press button = (-) hours decrease

- Program Daily start minute Press button = (+)minutes increase or Press button = (-)minutes decrease

2-way HHU Quick feature programming

Enter : Press & hold “F” button until 3 beeps heard, release “ F” button LCD highlight flashing icon first,

press and release “F” button to move blinking cursor to the desired icon which you want to program. Press button means Enable, 2-way LCD HHU Note: Cursor method: a constant illumination mean the selected feature enable. Exit : Press & hold " F " button for 2 sec. or do nothing wait for 5 sec. automatic exit

2-way LCD (1 beep) => Confirm Exit.

Button LCD display & Button

Press and hold the Button until 3 beeps sounded

Press & Release “ F” button to move cursor flash to Key Lock icon

Manual gear reservation Icon flash

Press button Enable Turbo mode

Press button Enable, sound “ Do-Re-Mi “or button Disable Key lock mode, sound “ Mi-Re-Do “

Turbo Timer icon flash

Key lock icon flash sound

Icon stay On = Enable

Icon Off = Disable.

Icon stay On = Enable Icon Off = Disable

RS-777 OP REV 1D

Page 7

2013/05/29

Press & Release “ F” button to move cursor flash to Daily Start icon

Press & Release “ F” button to move cursor flash to TIME START

Daily start icon flash

Timer start icon flash

Press button Enable Daily start mode.

Press button Enable Timer Start mode.

icon

OPERATION:

A. REMOTE TRANSMITTER OPERATION:

Transmitter

Button

----

Arm and Delete The 2 Stage Shock

- Arm System and Hidden Alarm

+ +

----

Unlock Doors & Disarm System

Two Steps Door Unlock & Disarm

----

Activate or Turn Off The Remote Start

System Function Remark

Lock Doors & Arm System

Panic function Press and Hold for 3 seconds

Car Locator Under armed mode

Sensor

Function

Silent Arming / Disarming Ignition in "off" position.

Active Anti Car-Jacking Mode

System

Trunk Release (Channel 3) Press and Hold for 2 seconds

Passive Arming By-pass While the system Disarmed.

Channel # 4 Timer Output (4)

Switching code For 2nd Car

Operation.

Press twice within 3 seconds

Press within 3 seconds and Hold

button for 2 seconds

Ignition in "on" position press and hold for 2

Press twice within 3 seconds.

Press button once.

For regular TX-935 remote transmitter Only

B CHIRP INDICATORS: C. PARKING LIGHT:

Chirp Function

1 chirp 2 chirps 3 chirps 4 chirps 6 chirps

Arm

Disarm

Defective Reminder

Disarm / Triggered

Car Locator

Parking light Function

1 flash 2 flashes 3 flashes

12 flashes

Constant On

Arm

Disarm

Disarm / Triggered

Car Locator

Under Remote Start

D. ALARM OPERATING CONDITION:

Siren / Horn Parking Light

1. Arming 1 or 3 Chirps 1 Flash Slow Flash Locking Disable

2. Disarming 2 or 4 Chirps 2 or 3 Flashes

3. Trigger Alarming Flashes Slow Flash

4. Passive Starter

Disable

5. Panic Alarming Flashes Flashes

6. Car-Jacking Alarming Flashes Disable

7. Car Locator 6 Chirps 12 Flashes

Fast Flash

LED Doors Starter Dome Light

Unlocking

Disable Disable

Locking

Turns on for 30

-second Flashes

Flashes

Icon On = Enable Icon Off = Disable

seconds

Optional

E. ACTIVE ARMING – LOCK & ARM:

1. Press

RS-777 OP REV 1D

button

on the transmitter.

Page 8

2013/05/29

The siren will chirp once and parking light will flash once indicating that the system is now armed. The vehicle’s

doors will lock upon arming if interfaced with the security system. DEFECTIVE SENSOR REMINDER: If the siren sounds 3 chirps and parking light flash one time, then you have left a door, trunk, or hood lid ajar.

SILENT ARMING / DISARMING: Press the transmitter and buttons at the same time will arm or disarm your security system, No chirp sound will be heard, arm / disarm confirmation will be through the vehicles parking lights only.

SENSOR BY-PASS:

The sensor bypass feature is programmed to activate for one arming cycle only. The security system will return to normal operation during the next arming cycle.

Sensor By-Pass : By 2-way HHU operation Table – 1 PASS 1 icon on, or press the button two times within 5 seconds will arm the security system and Bypass sensor 1 (zone 4 shock sensor).

HIDDEN ALARM FUNCTION: By 2-way HHU operation Table -1-2 icon on, Or by remote operation press the button first; within 3 seconds press the button to activate the hidden alarm function. The security system will arm and with

“Hidden Alarm Function” The siren / horn will be silenced even if the sensor is triggered in the armed status.

Alarm indication will only appear on the LCD.

F. PASSIVE ARMING

Active arming / disarming is controlled by your security system via the remote transmitter. This security system is equipped with an optional Passive Arming feature, which allows the security system to arm 30 seconds after the last door is closed. Operation is as follows.

1. Turn the ignition to the “OFF” position and exit the vehicle.

2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any door / hood / trunk, the security system LED will stop flashing. It will begin flashing again once all vehicle entrances are closed.

3. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren will chirp [1] time and the parking lights will flash [1] time.

PASSIVE ARMING WITH PASSIVE DOOR LOCKING

The vehicle doors will automatically lock after the passive arming cycle has been completed.

PASSIVE ARMING BY-PASS:

with [1] chirp and LED will turn “ON”. The security system will remain in this temporary state for as long as you wish. To exit passive by-pass, press the transmitter or buttons and the system will return to normal status.

While the system is disarmed, Press the button twice, the system will respond

G. ACTIVE DISARMING – UNLOCK & DISARM:

1. Press button on the transmitter.

2. The siren will chirp twice and the parking lights will flash twice indicating that the security system is now disarmed. The vehicle’s doors will unlock and the dome light will turn on for 30 seconds upon disarming. (Note: Power door locks and dome light must be installed with the security system.)

TAMPER DISARMING: If the alarm is triggered upon disarm, the system’s siren will chirp 4 times, and the parking

lights will flash 3 times. PATHWAY ILLUMINATION: When receiving an unlock /disarm signal, this feature will turn the parking lights “ON” for 30 seconds and for 10 seconds upon the lock signal. TWO STEPS DOOR UNLOCK: This feature will independently unlock the driver’s door only when disarming the

security system. Pushing the button a second time within 3 seconds will unlock the other doors. AUTOMATIC RE-ARM: If this feature is selected, the security system will automatically re-arm itself in 60 seconds after disarming with remote transmitter. Automatic rearm will cancel if any door is opened before the 60 seconds timer has elapsed.

H. DISARMING WITHOUT A TRANSMITTER

OVERRIDES THE ALARM WITHOUT PASSWORD PIN CODE:

(Factory Default Setting)

The Override function may be used if the remote transmitter is lost or inoperative.

1. Enter the vehicle and turn the ignition switch to 'ON’ position.

2. (Alarm will sound.)

3. Within 10 seconds push and release the valet switch. The alarm will stop sounding and enter the disarm mode. You can now start and operate the vehicle normally.

OVERRIDE THE ALARM WITH PASSWORD PIN CODE:

Unlike valet switch easily found, and defeated, this security system allows the consumer to program a password pin code. Offering a higher level of security.

1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)

2. Within 5 seconds, enter your chosen first digit code by pressing and releasing the Valet Switch. (When finished

above procedures, system's siren will stop alarming, lights will stop flashing, but the vehicle can’t be started.)

3. Within 15 seconds of the last digit code enter (the 1st code), then turn the Ignition Switch “OFF” and then “ON”.

4. Within 15 seconds, enter your chosen second digit code by pressing and releasing the Valet Switch.

5. Turn the ignition switch “OFF” position. 4 Chirps from siren/horn and 3 flashes from the parking light indicate the

system has disarmed.

RS-777 OP REV 1D

Page 9

2013/05/29

Note : You must override the alarm within 60 seconds. If not, the system will automatically re-arm.

EXAMPLE: To Override The System With The Password Code 83,

1. Enter the vehicle and turn the ignition switch to the 'ON’ position. (Alarm will sound.)

2. Within 5 seconds, Press and Release the Valet Switch 8 times, (When finished the system's siren will stop alarming, lights stop flashing, but the vehicle can not be started or driven away.)

3. Within 15 seconds of entering the last digit code enter (the 1st code), turn the Ignition Switch “Off” and then “ON”.

4. Within 15 seconds, Press and Release the Valet Switch 3 times.

Turn the Ignition Switch to the “Off” position. 4 Chirps form siren/horn and 3 flashes from the parking lights will

indicate the system has disarmed.

I. VALET MODE:

VALET MODE:

The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm functions and remote start functions are bypassed, however, the remote panic feature and remote door locks will remain operational. To use the valet mode, the system must first be disarmed either by using your remote transmitter, or by operating the Manual Override sequence.

Get into/out valet mode using the ignition key.

Enter Valet Mode: a). Under disarm mode, turn the ignition to “ON” position. b). Press and hold valet switch for 2 seconds until the LED turns on. The LED will remain on as long as

the system is in 'valet mode'. Exit Valet Mode: a). Turn ignition 'on'. b). Push and hold valet switch for 2 seconds, The LED will turn off indicate the system are exiting the

valet mode.

(System in Disarm)

J. CAR LOCATOR

Under armed mode, press the button to active car locator function. The siren will chirp 6 times. The parking light will flash 12 times, for you to easily locate your car.

K. PANIC FUNCTION:

The transmitter can be used as a remote panic switch to manually trigger the alarm in case of emergency.

1. Press and hold the button for 3 second. The alarm will immediately sound.

2. During panic mode, the normal function of this transmitter button will be disabled. The transmitter and buttons can be used to lock and unlock the door (if the option is installed), however once the button is

pressed, the vehicle’s starter disable device, (where installed) will be disengaged allowing the vehicle to start.

3. To stop the alarm, press and hold the transmitter or button on the transmitter again for 3 seconds. Also, if any transmitter buttons other than or button is pressed and released, the panic mode will be turned off

immediately.

4. If the button is not pressed, the alarm will automatically stop after 30 seconds.

L. TRIGGER THE SYSTEM

When armed, your vehicle is protected as follows: Light impact will trigger the warn-away signal. Heavy impacts / Doors open /(if installed) Hood open / (if installed) Trunk open / Turning on the ignition key will trigger the programmed sequence. The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren, horn, parking lights, and dome light will turn on alerting of an intrusion for 30 seconds. Then it will stop and automatic reset and re-arm. If the any one of the sensors or detectors is still active, the alarm system will sound a maximum of 3 times of 30 seconds cycles

NOISE ABATEMENT CIRCUIT:

Your system has a “Noise Abatement Circuit”. It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental conditions such as thunder, jackhammers airport noise, etc. Here’s how “Noise Abatement Circuit” works: The alarm triggers five times. Each time, the same sensor or switch has triggered the alarm; the “Noise Abatement Circuit” will interpret this pattern of triggers as a false alarm. After the third trigger, the “Noise Abatement Circuit” ignores, or bypasses, that sensor or switch until a different sensor or switch is trigger. “Noise Abatement Circuit” covers doors (Hood/Trunk) differently: If the alarm is triggered by an open door for 3 full cycles, the doors will be bypassed until the trigger ceases.

M. ANTI HI - JACKING

Warning: If you don't need the car jacking function in this alarm system, be sure to set car jacking feature

“OFF”. This system is default setting all cars jacking “OFF”.

ACTIVE ANTI CAR JACKING:

RS-777 OP REV 1D

Page 10

2013/05/29

1.Under ignition on press F button four times while “CAR JACK” flash on text area(see Table 1), then press button for 2 seconds to activate Anti Car-Jacking mode or

Under ignition on press and hold the and buttons at the same time for 2 seconds. The parking

lights will turn on for 1.5 seconds to indicate the system enter the anti car-jacking mode.

2.Once the system in anti car-jacking mode, the system will be triggered when the door is opened and closed while the ignition is “ON”.

PASSIVE ANTI CAR- JACKING:

It will operate as noted below:

1. Turn the ignition switch to the “ON” position and the system will arm.

2. Once the system is armed, if you are forced from the vehicle, the system will trigger when the door is opened and closed while the ignition is “ON”.

TRIGGER THE ANTI CAR -JACKING MODE:

a). 50 seconds after the system has beer triggered. The siren will start chirping for 15 seconds.

b). During this 15 second period of chirping, you will be alerted to push the valet switch once to turn off the

car-jacking feature. If not, it will enter a second timer for car jacking.

c). 65 seconds after the system has been triggered, the siren will start sounding and the parking lights will start

flashing.

d). 90 seconds after the system has been triggered,

1. The siren will sound and the parking lights will flash, and

2. The starter disable will activate to prevent the vehicle from starting.

3. It will remain active until the vehicle's battery power is exhausted.

OVERRIDE THE SYSTEM TO TURN OFF ANTI CAR- JACKING:

Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch, the siren will stop and the system

disarmed Note: If you use password pin code to double protect the vehicle security, you will need to use it to completely disarm the system.

N. SYSTEM’S TRIGGER CHECK

(For two-way transceiver operation only)

By Table – 2, press and hold F button of LCD remote until 2 beeps heard, release and re-press F button 2

more times, the LCD display show “ALARM CHECK “ on text field (see Table 2), then press button to

activate system trigger check.

Note: If it has no response then you are out of range.

O. SYSTEM’S STATUS CHECK

(For two-way transceiver operation only)

By Table – 2 press and hold F button of LCD remote until 2 beeps heard, release and re-press F button

one more time, the LCD display show “STATUS CHECK “ on text field (see Table 2) then press

button to activate system status check.

Note: If it has no response then you are out of range.

P. DRIVER PAGING / LOSE & FOUND (

For two-way transceiver operation only) It is useful the event that someone wants to page the driver of the parked vehicle or someone cannot find his LCD remote transceiver. Under the ignition switch “off” condition, press and hold the valet switch for 3 seconds to page the driver, one chirp sound shall be emitted from the vehicle and the paging melody sound continues sounding from you Remote LCD transceiver.

DOME LIGHT CONVENIENCE SUPERVISION (Optional Feature)

The alarm has a unique feature that will turn on your vehicle dome light as follows:

1. Upon disarming, the interior light will remain on for 30 seconds.

2. If the vehicle is intruded, the interior light will flash for the same duration as the siren. Note: Turning on the ignition switch or arming the alarm will turn off the dome light.

IGNITION CONTROL DOOR LOCK/UNLOCK. (Programmable Feature)

If the vehicles door locks have been interfaced to the security system, the system will automatically lock the vehicle's doors when the ignition is turned “ON” and /or unlock the vehicle’s doors when the ignition is turned “OFF”. (Default is “OFF”)

S. TRUNK RELEASE (CHANNEL 3) OUTPUT.

Press and hold button on the transmitter for two seconds to remote control the trunk release or other

electric devices.

CHANNEL 4 TIMER CONTROL OUTPUT

By Table – 1, Press and hold F button of LCD remote until 1 beep sound , release and re-press F button 3 more times the LCD display show “CH 4“ on text field (see Table 1) then press button to activate channel 4 function. Or press remote

function. Channel 4 is user-programmable timer output. You may program the built-in timer to send a ground signal for any time duration from 1 second to 120 seconds. For instance, this timer output may be used to turn on the headlight, power window or sunroof. (Factory defaults setting at 1 sec. pulse output.)

transmitter and buttons at the same time to active Channel 4

RS-777 OP REV 1D

Page 11

2013/05/29

U. POWER SAVER MODE (Default OFF)

By table - 2 -1– 4 under Menu mode while “POWER SAVE” icon flash press

“

Save

” unit under power save mode, the LCD remote transceiver use “0” current to save the battery power, LCD

indicate “SAVE “.

Exit: Press any button of the LCD remote transmitter to exit “Power Save Mode”.

button, LCD HHU show

V. POWER ON MEMONRY:

This security system is equipped with circuitry that will allow the unit to remember its alarm state if the power is lost and then reconnected.

W. SECOND VEHICLE SECURITY OPERATION:

Your 1-way remote transmitter can be utilized to control a second vehicle security system, To program the remote control transmitter to a second vehicle, follow the instructions

* For 1-way transmitter press button

1. Once shift button (

built-in.

2. Press any button on the remote control transmitter to control a second vehicle security system LED on Transmitter

will flash 2 times indicate it’s 2nd car operation no matter which button is pressed.

** For LCD transceiver – 2nd car operation :

+ )

+ for 2 seconds until transmitter LED

is pressed the LED flash 2 times to indicate the second transmitter pin code has

(flash 2 times ) as a shift button.

a. By table-2-1-6 Press and hold F button until 2 beeps heard, release F button b. flash on the text field of LCD screen, press button to enter the menu mode.

c. Press & release button to move down the menu to #6, CAR SELECT d. Select CAR 1 or CAR 2 by pressing or button (text field show CAR 1 or CAR 2).

X. CHECK VEHICLE’S VOLTAGE:

Press and hold F button of LCD remote until 2 beeps sound , release and re-press F button for three times, the LCD remote will show “VOLTS CHECK“ icon flash on text area (see Table 2), then press button to

activate system Voltage check. Please note that this data is for your reference only. Please check the exact data on vehicle.

REMOTE START OPERATION:

A. TO REMOTE START THE VEHICLE:

When you want to start your vehicle,

1. Press button once on the transmitter.

2. The parking light will activate to indicate the remote start received the signal.

3. The engine will start in approximately 5 seconds.

4. Once the engine is running, after couple seconds the parking lights will turn on and the climate controls will activate and adjust the vehicle’s interior temperature to your presetting. (While the vehicle is running, the “minutes” digit on the LCD screen will flash and the will indicate count down timer based on the 5, 10, 20 or 30 minute run time set up by your installation center.)

5. The vehicle will run for a programmable 5 to 30 minute cycle before shutting down. (When the unit shuts off the count down timer will turn off and the transmitter will play a melody.) NOTE: The Remote Start Unit will not start the vehicle if any one of the following conditions exists:

1. The hood is opened.

2. The brake pedal is pressed.

3. The optional remote start enable toggle is switched to the “OFF” position. (If installed)

4. The gear selector is in any gear other then “PARK” or “NEUTRAL”

SAFE START (Child safety mode)

Factory default is set to press the button once on the transmitter to start the vehicle. You can program this feature to eliminate an accidental remote start:

1. The user presses the transmitter buttons twice within 3 seconds to start the vehicle. or

2. The user presses the transmitter and button at the same time to start the vehicle.

NOTE: Contact your installing dealer to activate this feature.

B. OPERATE THE VEHICLE WHILE RUNNING FROM THE REMOTE START:

To operate the vehicle while engine running from the remote start,

1. Insert the ignition key and turn it to “ON” (not the start) position.

2. Press the brake pedal.

Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down.

C. TEMPORARY STOP FEATURE:

This feature allows the vehicle to remain running after the key has been removed from the ignition. This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would like to leave the motor running and the climate control on.

RS-777 OP REV 1D

Page 12

2013/05/29

1.Before turning off the engine, press the button once on the transmitter and the LED indicator will flash 3 times

to confirm.

2.Turn the ignition key to OFF position. (The engine will stay running.)

3.The engine will run until the pre-programmed time elapsed or shutdown input is received.

D. TURBO CHARGE MODE:

Turbo charge mode keeps the engine running after arriving at you destination for a programmable period of 1, 3 or 5 minutes, This allows the vehicle’s engine time to conveniently cool down the turbo after you have left the vehicle. To activate:

1. While the engine is running, pull up the hand brake and place the transmission gear in the park position.

2. Before turning off the engine, press and release and buttons at the same time.

-- The LED will flash indicating the remote start has entered the turbo charge mode appear on LCD remote.

3. Take the “Ignition Key” from the key cylinder.

-- Engine keeps running. --

4. Exit and secure the vehicle.

-- Engine continues running until the pre-programmed time elapsed. --

1. While the engine is running, pull up the hand brake and place the transmission gear in the park position.

2. Before turning off the engine, ref.2-way HHU quick feature programming (page 6) enable Turbo mode feature

turn on LCD remote.

3. Take the “Ignition Key” from the key cylinder.

-- Engine keeps running. --

4. Exit and secure the vehicle.

-- Engine continues running until the pre-programmed time elapsed. --

NOTE: This feature only applies to vehicles with Turbo Engines.

E. TIMER & DAILY START:

This unit can be programmed to start and run the engine every 3 / 2 hours the engine will run for the programmed running time and then shut down. IMPORTANT: Timer Start should be used only in open areas, never start and run the vehicle in on enclosed space as a garage or carport. Daily Timer Start: The feature is very useful for the driver who wants to run the vehicle punctually at the same time next morning. Before set-up of the “Daily Timer Start”, you should pre-set the time you intend to start engine (Hour / Minutes) by Table-2 -1 -7 set up Daily start first.

TIMER START:

Enter :

1. Turn Ignition On => Off

2. After above (1) within 15 seconds, (ref. page-6 2-way HHU quick feature programming => Enable Time start.) p

ress and hold F button of LCD remote until 3 beeps sound , release and re-press F button until LCD

show “ “ icon flash on LCD remote (see Table 3), then press button to activate

illuminate on LCD display,

start every 3 or 2 hours

parking light flash / siren chirp 3 or 2 times confirm. The vehicle is now programmed to

Time Start.

icon

Exit : Turn Ignition On (LED and parking light flash 4 times, and siren chirp 4 times confirm exit Time Start).

(p.s. press lock or unlock button to turn off icon on 2-way remote)

Daily Start :

Enter :

1. Turn Ignition On => Off

2. After above (1), within 15 sec. ref. page-6 2-way HHU quick feature programming => Enable Daily Start (

& hold F button of LCD remote until 3 beeps heard, release and re-press F button to move blinking cursor to “ “ (see Table 3), then press button to activate Daily Start

display,

parking light flash / siren chirp 6 times confirm Daily Start programmed.

icon illuminate on LCD

Exit : Turn Ignition On (LED and parking light flash 4 times, and siren chirp 4 times confirm exit Daily Start).

(p.s. press lock or unlock button to turn off icon on 2-way remote)

F. TEMPERATURE CHECK

The unit can monitor the present indoor temperature of the passenger compartment before cooling or heating your vehicle. P

ress and hold F button of LCD remote until 2 beeps sound , release and re-press F button for 4

Press

RS-777 OP REV 1D

Page 13

2013/05/29

more times, the LCD remote will show “TEMP CHECK“ icon (see Table 2- 5), then press button

in-door temperature will be shown on the LCD screen. This reading may be higher than actual ambient temperature due to the greenhouse and is relative only the inside vehicle temperature.

G. TO TURN OFF THE REMOTE START:

When the engine is running (by remote start), if you want to stop it,

1. Press button once on the remote transmitter under remote start mode.

2. Move the optional remote start enable toggle switch to OFF position. (If installed)

3. Press the brake pedal The vehicle will shut down and turn off the parking light to indicate engine stopped.

H. SHUT-DOWN INPUT FOR REMOTE STARTER:

If any of the following conditions exist while the system is operating, the engine will not start or will shut down immediately:

1. The hood is opened.

2. The brake pedal is pressed.

3. The parking (hand) brake is released (For Standard Transmission Gear Vehicle or Turbo Timer Mode)

4. Engine is over-revved. {“Tachometer checking type” only}

5. The pre-programmed run time

(5 /10 / 20 / 30 minutes)

has elapsed.

6. Press button twice on the remote transmitter under remote start mode.

7. The system trigger.

8. The vehicle refused to start running after {3} unsuccessful attempts.

I. DISABLING THE REMOTE START SYSTEM: (If installed)

This feature allows your system’s remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed area. To disable the remote start, move the optional remote start enable toggle switch to the OFF position.

; the

RS-777 OP REV 1D

Page 14

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example

- use only shielded interface cables when connecting to computer or peripheral devices).

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Advance Security RS-777 Users Manual

Specifications and Main Features

Frequently Asked Questions

User Manual