PRO PLM Installation Instructions
PROFESSIONAL INST ALLA TION STRONGLY RECOMMENDED
Installation Precautions:
Roll down window to avoid locking keys in vehicle
during installation
Avoid mounting components or routing wires near
hot surfaces
Avoid mounting components or routing wires near
moving parts
Tape or loom wires under hood for protection and
appearance
Use grommets when routing wires through metal
surfaces
Use a Digital Multi Meter for testing and verifying
circuits. DO NOT USE A TEST LIGHT, OR
"COMPUTER SAFE PROBE" as these can set off air
bags or damage vehicle computers.
Technical Support (800) 225-6074
or go to
http://techservices.audiovox.com
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference that may
cause undesired operation.
Warning! Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
1
PRO PLM SYSTEM LAYOUT
TRACKING PORT
PROGRAMMING BUTTON
BLACK GROUND
YELLOW IGNITION
PURPLE DOOR TRIGGER (+)
RED/WHITE +12 VOLT BATTERY
8 Pin
WHITE PARKING LIGHT OUTPUT
BROWN DOOR TRIGGER (-)
RED PARKING LIGHT INPUT
ORANGE ARMED OUTPUT (-)
PROPLM
OPEN
DK GREEN INSTANT TRIGGER (-)
BLACK/WHITE HORN OUTPUT (-)
6 Pin
LT. GREEN INSTANT TRIGGER (-)
GREEN/WHITE ILLUMINATED ENTRY (-)
DK BLUE TRUNK RELEASE (-)
BLUE TRUNK SHUNT (+)
RED/BLACK DISARM INPUT 2
RED DISARM INPUT
5 Pin
GREEN/BLACK ARM INPUT 2
GREEN ARM INPUT
RED/BLACK 2ND UNLOCK
GREEN UNLOCK OUPUT (-)
3 Pin
RED LOCK OUTPUT (-)
LED / OVERRIDE BUTTON
SHOCK SENSOR DIAL
DBI PORT
2
SETUP & PROGRAMMING - CONSUMER MODE
Consumer Mode Transmitter Programming Bank
1. Turn the ignition ON.
2. Press and release the override button 3 times.
3. The system will chirp 1 time.
4. Press the lock button of each transmitter you wish to program.
5. The system will respond with 1 chirp for each accepted transmitter .
6. Turn the ignition OFF to exit transmitter programming.
7. The system will chirp 2 times to confirm exit.
Note: This system has 1 button programming which programs all channels of the transmitter to the
system at once.
Consumer Mode Feature Programming Bank - No Transmitters
1. Turn the ignition ON.
2. Press and release the override button 3 times, the system will chirp 1 time.
3. Turn the ignition OFF, the system will chirp 2 times.
4. Turn the ignition ON, the system will chirp one time indicating option #1 in the feature bank. The
LED will flash the current setting for the option.
5. Use the override button to scroll through the selections in the feature bank, the system will chirp to
match the feature number.
6. Press the programming button on the module to change the desired feature. The LED will flash
indicating the features setting.
7. Turn the ignition OFF to exit programming, the system will chirp 1 time to confirm exit.
Consumer Mode Feature Programming Bank - With Transmitters
1. Turn the ignition ON.
2. Press and release the override button 3 times, the system will chirp 1 time.
3. Turn the ignition OFF, the system will chirp 2 times.
4. Turn the ignition ON, the system will chirp one time indicating option #1 in the feature bank. The
LED will flash the current setting for the option.
5. Use the CAR FIND/P ANIC button to scroll through the selections in the feature bank, the system will
chirp to match the feature number.
6. Press the LOCK button to change the desired feature. The LED will flash indicating the changed
feature.
7. Turn the ignition OFF to exit programming, the system will chirp 1 time to confirm exit.
Defaulting the Features in the Feature Programming Bank
1. Turn the ignition ON.
2. Press and release the override button 3 times, the system will chirp 1 time.
4. Press the programming button on the module, the system will chirp 4 times indicating the features
have been defaulted.
NOTE: The system will remain in programming mode as long as the ignition is on, there is no
time limit. To exit programming turn the IGNITION OFF.
3
SETUP & PROGRAMMING - CONSUMER MODE, CONTINUED
Dome Light Delay/Theater Lighting Programming
The system can be programed to delay arming after the lock button is pressed (60 second max) for vehicles
with a dome light delay or theater dimming feature. Once programed the system will ‘learn’ the timing of the
dome light delay and add 2 seconds before arming.
1. Close all doors with ignition off.
2. Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK , UNLOCK, LOCK. The LED will light
solid to indicate the system has entered DOME DELAY LEARN MODE.
3. Immediately OPEN then CLOSE the door WITHOUT disarming the system. The system will then monitor the
door trigger wire. Once the dome light turns off, the system will then add 2 seconds and then exit the
learning mode.
4. The LED will begin to flash indicating the system has exited the learning mode and is now armed.
CONSUMER MODE PROGRAMMING GUIDE
Transmitter Programming Bank
Feature Programming Bank 1 LED Flash 2 LED Flashes 3 LED Flashes
1. Security Function ON OFF
2. Passive Locks Passive Active
3. Silent Choice ON OFF
4. Passive/Active Arming Passive Active
5. Siren/Horn Siren Horn
6. Door Trigger Delay Instant 15 Second
7. Arm 2 Input Polarity NEG POS
8. Chirps ON OFF
9. Extended Locks 0.9 sec. 3 sec. Dbl pulse U/L
10. Ignition Controlled Locks ON OFF
11. Dk Blue Wire Output Trunk ITS Function
12. Disarm 2 Input Polarity NEG POS
13. Horn Output Timing 16mS 40mS 72mS
14. Real Panic Sound ON OFF
Note: Default settings are in BOLD print.
Changing option #11 to ITS Function changes the functionality of the entire system, refer to the ITS Functionality
section on page 22 of this manual.
4
SETUP & PROGRAMMING - LOT MODE
Lot Mode Transmitter Programming Bank - ACM Transmitter
1. Turn the ignition ON.
2. Press and release the override button 3 times.
3. The system will chirp 1 time.
4. Enter the desired VEHICLE NUMBER into the ACM keyp ad and then press the LOCK button.
5. The system will respond with 1 chirp.
6. Turn the ignition OFF to exit transmitter programming.
7. The system will chirp 2 times to confirm exit.
Note: This system has 1 button programming which programs all channels of the transmitter to the
system at once.
When an ACM keyp ad is programmed to the system, it is automatically transitioned into Lot Mode.
Only 1 vehicle number may be learned to the system.
Lot Mode Feature Programming Bank - No ACM Transmitter
1. Turn the ignition ON.
2. Press and release the override button 3 times, the system will chirp 1 time.
3. Turn the ignition OFF, the system will chirp 2 times.
4. Turn the ignition ON, the system will chirp one time indicating option #1 in the feature bank. The
LED will flash the current setting for the option.
5. Use the override button to scroll through the selections in the feature bank, the system will chirp to
match the feature number.
6. Press the programming button on the module to change the desired feature. The LED will flash
indicating the features setting.
7. Turn the ignition OFF to exit programming, the system will chirp 1 time to confirm exit.
Lot Mode Feature Programming Bank - With ACM Transmitter
1. Turn the ignition ON.
2. Press and release the override button 3 times, the system will chirp 1 time.
3. Turn the ignition OFF, the system will chirp 2 times.
4. Turn the ignition ON, the system will chirp one time indicating option #1 in the feature bank. The
LED will flash the current setting for the option.
5. Use the CAR FIND/P ANIC button to scroll through the selections in the feature bank, the system will
chirp to match the feature number.
6. Press the LOCK button to change the desired feature. The LED will flash indicating the changed
feature.
7. Turn the ignition OFF to exit programming, the system will chirp 1 time to confirm exit.
Defaulting the Features in the Feature Programming Bank
1. Turn the ignition ON.
2. Press and release the override button 3 times, the system will chirp 1 time.
4. Press the programming button on the module, the system will chirp 4 times indicating the features
have been defaulted.
NOTE: The system will remain in programming mode as long as the ignition is on, there is no
time limit. To exit programming turn the IGNITION OFF.
5
SETUP & PROGRAMMING - LOT MODE
Dome Light Delay/Theater Lighting Programming
The system can be programed to delay arming after the lock button is pressed (60 second max) for vehicles
with a dome light delay or theater dimming feature. Once programed the system will ‘learn’ the timing of the
dome light delay and add 2 seconds before arming.
1. Close all doors with ignition off.
2. Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK , UNLOCK, LOCK. The LED will light
solid to indicate the system has entered DOME DELAY LEARN MODE.
3. Immediately OPEN then CLOSE the door WITHOUT disarming the system. The system will then monitor the
door trigger wire. Once the dome light turns off, the system will then add 2 seconds and then exit the
learning mode.
4. The LED will begin to flash indicating the system has exited the learning mode and is now armed.
LOT MODE PROGRAMMING GUIDE
Transmitter Programming Bank
Feature Programming Bank 1 LED Flash 2 LED Flashes 3 LED Flashes
1. Security Function ON OFF
2. Passive Locks Passive Active
3. Silent Choice ON OFF
4. Passive/Active Arming Passive Active
5. Siren/Horn Siren Horn
6. Door Trigger Delay Instant 15 Second
7. Arm 2 Input Polarity NEG POS
8. Chirps ON OFF
9. Extended Locks 0.9 sec. 3 sec. Dbl pulse U/L
10. Ignition Controlled Locks ON OFF
11. Dk Blue Wire Output Trunk ITS Function
12. Disarm 2 Input Polarity NEG POS
13. Horn Output Timing 16mS 40mS 72mS
14. Real Panic Sound ON OFF
15. Lot Alert OFF ON
Note: Default settings are in BOLD print.
Changing option #11 to ITS Function changes the functionality of the entire system, refer to the ITS Functionality
section on page 22 of this manual.
6
TRANSITIONING BETWEEN MODES - ACM TRANSMITTER
Transitioning into Lot Mode - ACM Transmitter
1. Turn the ignition ON.
2. Press and release the override button 3 times.
3. The system will chirp 1 time.
4. Enter the desired VEHICLE NUMBER into the ACM keyp ad and then press the LOCK button.
5. The system will respond with 1 chirp.
6. Turn the ignition OFF to exit transmitter programming.
7. The system will chirp 2 times to confirm exit.
Note: This system has 1 button programming which programs all channels of the transmitter to the
system at once.
Use of an ACM keyp ad is required.
Once an ACM keyp ad is programmed to the system, it is automatically transitioned into Lot Mode.
Only 1 vehicle number may be learned to the system.
When in lot mode, a consumer remote can not be programmed to the system until it is transitioned to
consumer mode.
All programming features will be defaulted to the factory default settings.
Transitioning into No-Sale Mode - YELLOW
1. Open a vehicle door.
2. Enter the vehicle number into an ACM keyp ad.
3. Press the UNLOCK button.
4. Press and release the # button.
5. Press and release the “YELLOW” button.
6. Close the vehicle’s door .
Note: The ACM keyp ad must be authorized for transitioning.
Note: No-Sale mode disables all functionality of the unit, the unit will be inoperable until reprogrammed
with the PROPLPR programming device. This mode is only used when there is a no-sale of the product
and you are not removing the system from the vehicle.
Transitioning into ITS Mode - GREEN
1. Open a vehicle door.
2. Enter the vehicle number into an ACM keyp ad.
3. Press the UNLOCK button.
4. Press and release the # button.
5. Press and release the “GREEN” button.
6. Close the vehicle’s door .
Note: The ACM keyp ad must be authorized for transitioning.
Note: ITS mode enables the shock sensor only of this device for applications in a vehicle equipped with
a factory security system.
7
TRANSITIONING BETWEEN MODES - ACM TRANSMITTER, CONTINUED
Transitioning into Factory Keyless Upgrade Mode - BLUE
1. Open a vehicle door.
2. Enter the vehicle number into an ACM keyp ad.
3. Press the UNLOCK button.
4. Press and release the # button.
5. Press and release the “BLUE” button.
6. The LED will flash blue 1 time and the system will chirp 3 times.
7. Close the vehicle’s door .
Note: The ACM keyp ad must be authorized for transitioning.
Note: Factory Keyless Upgrade Mode enables all of the device’s security functionality by use of the
factory transmitters.
Transitioning into Security with Transmitters Mode - RED
1. Open a vehicle door.
2. Enter the vehicle number into an ACM keypad.
3. Press the UNLOCK button.
4. Press and release the # button.
5. Press and release the “RED” button.
6. The LED will flash red 1 time and the system will chirp 3 times.
7. Within 5 seconds program the aftermarket transmitter by pressing the lock button of each transmitter you wish to program.
8. Close the vehicle’s door .
Note: The ACM keypad must be authorized for transitioning.
Note: If no remotes are programmed during step 7, the system will automatically transition into the
Factory Keyless Upgrade Mode - BLUE
Note: Security with Transmitters Mode enables all of the device’ s security functionality by use of
aftermarket transmitters.
8
Loading...