Advance Security CA6150RX Installation guide

PROFESSIONAL

SERIES

Remote Start with Keyless Entry

Installation Guide

CA6150RX

Table of Contents

Before You Begin ......................................................................................3

Wire Connection Guide ........................................................................... 4

8 Pin Main Harness ...................................................................................5

3 Pin Parking Light Harness ..................................................................... 8

6 Pin Start Harness...................................................................................8

4 Pin Auxiliary Harness .......................................................................... 10

2 Pin Door Lock Output Harness ........................................................... 11

Additional Ports ...................................................................................... 15

Antenna / LED / Programming Port .......................................................15

DBI Port....................................................................................................15

Tracking Port ...........................................................................................15

Set Up & Programming ..........................................................................16

Transmitter Programming........................................................................16

Manual Feature Programming.................................................................16

Programming Feature Banks .................................................................. 17

T ach Programming ..................................................................................18

Smart Tachless.Mode .............................................................................18

Feature Descriptions ............................................................................. 19

Transmitter Button Functions ............................................................. 22

Remote Start Shutdown Diagnostics ................................................23

System Layout .........................................................................................24

BEFORE YOU BEGIN

PROFESSIONAL INST ALLA TION

STRONGLY RECOMMENDED

Installation Precautions:

Roll down window to avoid locking keys in vehicle during installation

Avoid mounting components or routing wires near hot surfaces

Avoid mounting components or routing wires near moving parts

Tape or loom wires under hood for protection and appearance

Use grommets when routing wires through metal surfaces

Use a Digital Multi Meter for testing and verifying circuits. DO NOT USE A TEST LIGHT, OR "COMPUTER SAFE PROBE" as these can set off air bags or damage vehicle computers.

Technical Support

or go to

http://techservices.codesystems.com

(800) 421-3209

8 Pin Main Harness

3 Pin Parking Light Harness

6 Pin Start Harness

4 Pin Auxiliary Output Harness

2 Pin Lock Output Harness

8 Pin Main Harness

1 VIOLET/BLACK AUX 1

This wire provides a ( - ) 500mA output capable of driving relays. For Control of optional accessories (i.e. Power Window/Sunroof, etc.).

To activate refer to the transmitter button configuration chart. Please refer to the selectable options for timing.

2 BLACK/WHITE ILLUMINATED ENTR Y OUTPUT ( - )

This wire provides a ( - ) 500mA output for 30 seconds when the system is disarmed capable of driving relays.

Locate the vehicle’s dome light or pin switch wire.

Verification: This wire will register positive voltage or ground when the vehicle's dome light is turned ON.

3 BROWN/BLA CK HORN OUTPUT ( - )

Locate the vehicle’s horn wire.

Verification: This wire will register at positive voltage and register ground when the horn switch is pressed.

Connect the BROWN/BLACK wire to the vehicle’s horn wire. This is a low current output, 500mA.

4 RED/WHITE TRUNK RELEASE OUTPUT ( - )

Locate the vehicle’s trunk release wire at the trunk release switch.

Verification: This wire will register either positive voltage or ground when the trunk release is activated.

This is a low current output, 500mA.

5 BLUE/BLACK IGNITION 3 / ACTIVE OUTPUT ( - )

The Active Output/Ignition 3 output wire provides a ground output when the remote start function is activated and remains until 4 seconds after the remote start is shutdown. The Ignition 3 output wire can be used for several functions listed below. If this wire will be used for multiple application's a 1 amp diode is required in-line with the stripe facing the control module.

Factory transponder (coded key) bypass. General Motors VATS bypass, see the following diagram. Use an SPDT relay (not

supplied). Ignition 3 output, see the following diagram. Use an SPDT relay (not supplied). Accessory 2/3 output, see the following diagram. Use an SPDT relay (not

supplied).

Ignition Switch

VATS Wire #1, WHITE or WHITE/BLACK

X CUT

VATS Control Module

VATS Wire #2, WHITE or VIOLET/WHITE

Fused +12 Volt Battery Source

GM VATS

87a

Matching Value Resistor

BLUE/BLACK ActiveOutput Wire

Ignition 3 Accessory 2/

Fused +12 Volt Battery Source

Jump To PINK Ignition Output Wire From Control Module

87a

To Vehicle's 2nd or 3rd Ignition Wire

BLUE/BLACK Active Outpu Wire

Jump To ORANGE Accessory Output Wire From Control Module

Fused +12 Volt Battery Source

87a

To Vehicle's 2nd or 3rd Accessory Wire

BLUE/BLACK Active Outpu Wire

6 PURPLE/WHITE TACH INPUT

Locate the vehicle’s ignition coil or fuel injector in the engine compartment.

Verification: Test using the following procedure:

1. Set voltmeter to AC VOLTS.

2. Attach positive lead of a volt meter to a constant 12-volt source.

3. Attach negative lead of a volt meter to the wire to be tested.

4. Start the engine.

5. Have someone press on the gas pedal slightly as you monitor the meter. If connected to the correct wire, the voltage reading will increase as the engine’s RPM increases.

Connect the PURPLE/WHITE wire to the negative side of the vehicle ignition coil or fuel injector.

7 GRAY HOOD PIN INPUT ( - )

Install a Hood Pin Switch and connect to the GRAY wire. This connection is required for Remote Start.

Verification: This wire when connected will register ground when the

vehicle's hood is opened. Connect the GRAY wire to the hood pin. NOTE: Be sure to loom the wire, and seal the grommet.

8 BROWN/RED BRAKE INPUT ( + )

Locate the vehicle’s brake light wire at the brake pedal mounted switch.

Verification: This wire registers positive voltage when the brake pedal is

pressed. Connect the BROWN/RED wire to the vehicle’s brake light wire.

3 Pin Parking Light Harness

1 BLACK GROUND

Connect the BLACK wire to a solid chassis ground point using a ring terminal and self tapping screw (not supplied). Scrape away paint from the grounding point to ensure a good connection. The recommended grounding point is a metal surface in the driver’s side kick panel area.

NOTE: Do not ground the BLACK wire with any other vehicle components.

2 WHITE/RED PARKING LIGHT INPUT

3 WHITE PARKING LIGHT OUTPUT

Locate the parking light output wire at the vehicle’s light switch.

Verification: This wire registers positive voltage when the parking lights are

turned on. Positive switching Parking Lights:

Connect the WHITE/RED wire to a 15 Amp max fused battery source.

Connect the WHITE wire to the parking light output wire. Negative switching Parking Lights:

Connect the WHITE/RED wire to a good chassis ground.

Connect the WHITE wire to the parking light output wire.

6 Pin Start Harness

1 PURPLE STARTER OUTPUT ( + )

Locate the vehicle starter wire.

Verification: This wire registers voltage only when the key is turned to the START position.

Verification:

The starter wire registers voltage when the key is turned to the START position.

Connect the PURPLE wire to the vehicle starter wire.

+ 18 hidden pages

Advance Security CA6150RX Installation guide

Specifications and Main Features

Frequently Asked Questions

User Manual