Advance Security 560A User Manual

JULY. 19. 2002

1

OPERATION:

A. REGULAR TRANSMITTER OPERATION:

Transmitter Button System Function Remark

-

(3-second)

-

-

(2-second)

Lock Doors & Arm System with Chirp Press & release within 1 seconds
Lock Doors & Arm System without Chirp Press & release over 1 seconds

Arm and Delete The 2 Stage Shock Sensor Press twice within 3 seconds.
Panic function Press and Hold for 3 seconds

Unlock Doors & Disarm System with Chirp Press & release within 1 seconds
Unlock Doors & Disarm System without Chirp Press & release over 1 seconds

Two Steps Door Unlock & Disarm System Press twice within 3 seconds.
Channel 2 (Trunk) Timer Control Press and Hold for 2 seconds
Activate or Turn Off The R emote Start or Press twice within 3 seconds.

B. LED display:

LED Function LED Function
Off Disarmed Zone 1: Warn -Away Trigger
Slow Flash Armed 2 flashes... pause Zone 2: Trigger on Trunk/Hood
Fast Flash Passive Arming 3 flashes... pause Zone 3: Trigger on Door Switch
On (Solid) Valet Mode 4 flashes... pause Zone 4: Trigger on Optional Sensor
5 flashes... pause Zone 5: Trigger on Ignition Switch

C. CHIRP INDICATORS: D. PARKING LIGHT:

Chirp Function Parking light Function
1 chirp Arm 1 flash Arm
2 chirps Disarm 2 flashes Disarm
3 chirps Defective Reminder 3 flashes Disarm / Triggered
4 chirps Disarm / Triggered 12 flashes Car Locator
Constant On Under Remote Start

E. ALARM OPERATING CONDITION:

Siren, Horn Parking Light LED Doors Starter Dome Light

1. Arming 1 or 3 Chirps 1 Flash Slow Flash Locking Disable

2. Disarming 2 or 4 Chirps 2 or 3 Flashes Fast Flash Unlocking Turns on for 30-second

3. Trigger Alarming Flashes Slow Flash Disable Flashes

4. Panic Alarming Flashes Flashes

F. ACTIVE LOCK & ARM:

1.Press button on the transmitter.

2.The horn will chirp once and parking light will flash once indicating that the system is now armed. The vehicle
doors will lock upon arming when interfaced with the security system.

SILENT ARMING / DISARMING: Press and hold the or button on the transmitter over 1 second will arm
or disarm your security system, No chirp sound will be heard, arm / disarm confirmation will be through the
vehicles parking lights only.

DEFECTIVE SENSOR REMINDER: If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar.
(See Alarm Feature “I - 4 Programming)

SHOCK SENSOR / OPTIONAL SENSOR BY -PASS:

Press the button once: The siren chirps once, The system is armed.

560A

JULY. 19. 2002

2

Press the button a second time within 3 seconds: The siren chirps twice, the Shock Sensor is now
bypassed.
The sensor bypass feature is programmed to activate for one arming cycle only. The security system will return
to normal operation during the next arming cycle.

H. PASSIVE ARMING

Active arming / disarming is controlling your security system via the remote transmitter. This security system is
equipped with an optional Passive Arming feature, which allows the security system to arm 30 seconds after the
last door is closed. Operation is as follows.

1. Turn the ignition to the “OFF” position and exit the vehicle.

2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any door
/ hood / trunk, the security system LED will stop flashing. It will begin flashing again once the vehicle all
entrances are closed.

3. After 30 -second timer has elapsed, the security system will automatically “ARM”. The siren will chirp [1] time
and the parking lights will flash [1] time.

PASSIVE ARMING WITH PASSIVE DOOR LOCKING (See Alarm Feature “I - 2” Programming):

The vehicle doors will automatically lock after passive arm ing cycle has been completed.

G. ACTIVE UNLOCK & DISARM:

1. Press button on the transmitter.

2. The horn will chirp twice and parking light will flash twice to indicating that the security system is now
disarmed. The vehicle doors will unlock and dome light wills turns on for 30 seconds upon disarming when
interfaced with the security system.

TAMPER DISARMING: If alarm triggered, upon disarm the system, siren chirp 4 times, parking light flash 3
times.

PATHWAY ILLUMINATION (See Alarm Feature “II - 4” Programming): This feature turns the parking light
“ON” for 30 seconds upon a unlock signal and for 10 seconds upon the lock signal.

TWO STEPS DOOR UNLOCK (See Alarm Feature “III - 3” Programming):: This feature will independently

unlock the drives door only when disarming the security system. Pushing the button a second time within
3 seconds will unlock the entire vehicle.

H. DISARMING WITHOUT A TRANSMITTER

The Override function may be used if the remote transmitter is lost or inoperative.

1. Enter the vehicle and turn the ignition switch to 'ON’ position.

2. Within 10 seconds push and release the valet switch

The alarm will enter the disarm mode. You can now start and operate the vehicle normally.

I. VALET MODE: (System in Disarm or Valet mode)

The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your
transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm function
and remote start function are bypassed, however the remote panic feature and remote door locks will remain
operational. To use the valet mode, the system must first be disarmed either by using you remote transmitter,
or by operating the Manual override sequence.

Enter Valet Mode:

1.From the disarmed condition, turn the ignition to “ON” position.

2.Push and hold valet switch for 2 seconds until the LED turns on. The LED wills remain on as long as the
system is in 'valet mode'.

Exit Valet Mode:

1.Return to normal operation, turn ignition 'on'.

2.Push and hold valet switch for 2 seconds, The LED wills turns off indicate the system are exiting the valet
mode.

J. PANIC FUNCTION:

The transmitter can be used as a remote panic switch to manually trigger the alarm in case emergency.

560A