Advance Multimedia Internet Technology WIQ318 Users Manual

WIQ318AM User’s Manual

Copyright

The contents of this publication may not be reproduced in any part or as a whole, stored, tran scribed in
an information retrieval system, translated into any language, or transmitted in any form or by any
means, mechanical, magnetic, electronic, optical, photocopying, manual, or otherwise, without the
prior written permission.

Trademarks

All products, company, brand names are trademarks or registered trademarks of their respective
companies. They are used for identification purpose only. Specifications are subject to be changed
without prior notice.

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against radio interference in a commercial environment. This equipment can generate, use and radiate
radio frequency energy and, if not installed and used in accordance with the instructions in this manual,
may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause interference, in which case the user, at his own expense, will be required to take
whatever measures are necessary to correct the interference.

CE Declaration of Conformity

This equipment complies with the requirements relating to electromagnetic compatibility, EN
55022/A1 Class B.

The specification is subject to change without notice.

1

Table of Contents

Chapter 1 Introduction.............................................................................. 3

Functions and Features ........................................................................3

Packing List .........................................................................................5

Chapter 2 Hardware Installation............................................................... 6

2.1 Panel Layout ..................................................................................6

2.2 Procedure for Hardware Installation.............................................. 7

Chapter 3 Network Settings and Software Installation............................. 9

3.1 Make Correct Network Settings of Your Computer....................... 9

Chapter 4 Configuring Wireless Broadband Router............................... 10

4.1 Login to Configure from Wizard ................................................. 11

4.2 Status............................................................................................ 13

4.4 Basic Setting ................................................................................ 14

4.5 Forwarding Rules......................................................................... 32

4.6 Security Settings .......................................................................... 36

4.7 Advanced Settings........................................................................ 50

4.8 T oolbox........................................................................................ 63

Appendix A TCP/IP Configuration for Windows 95/98 ........................ 68

Appendix B 802.1x Setting..................................................................... 73

Appendix C WPA-PSK and WPA.......................................................... 79

Appendix D FAQ and Troubleshooting.................................................. 92

What can I do when I have some trouble at the first time?...... 92

How do I connect router by using wireless?............................... 95

2

C

h

a

p

t

e

r

1

I

n

t

r

o

d

u

c

t

i

o

C

h

a

p

t

e

r

1

I

n

t

r

o

C

h

a

p

t

e

r

1

Congratulations on your purchase of this outstanding Wireless Broadband Router. This product is
specifically designed for Small Office and Home Office needs. It provides a complete SOHO solution
for Internet surfing, and is easy to configure and operate even for non-technical users. Instructions for
installing and configuring this product can be foun d in this manual. Before you install and use this
product, please read this manual carefully for fully exploiting the functions of this product.

Functions and Features

Router Basic functions

z Auto-sensing Ethernet Switch

Equipped with a 4-port auto-sensing Ethernet switch.

z WAN type supported

The router supports some WAN types, Static, Dynamic, PPPoE , PPTP ,L2TP, Dynamic IP
with Road Runner.

z Firewall

d

I

n

t

r

o

d

n

u

c

t

i

o

n

u

c

t

i

o

n

All unwanted packets from outside intruders are blocked to protect your Intranet.

z DHCP server supported

All of the networked computers can retrieve TCP/IP settings automatically from this product.

z Web-based configuring

Configurable through any networked computer’s web browser using Netscape or Internet
Explorer.

z Virtual Server supported

Enable you to expose WWW, FTP and other services on your LAN to be accessible to
Internet users.

z User-Definable Application Sensing Tunn el

User can define the attributes to support the special applications requiring multiple
connections, like Internet gaming, video conferencing, Internet telephony and so on, then this
product can sense the application type and open multi-port tunnel for it.

z DMZ Host supported

Lets a networked computer be fully exposed to the Internet; this function is used when
special application sensing tunnel feature is insufficient to allow an app lication to function
correctly.

z Statistics of WAN Supported

Enables you to monitor inbound and outbound packets

3

Wireless functions

z High speed for wireless LAN connection

Up to 54Mbps data rate by incorporating Orthogonal Frequency Division Multiplexing
(OFDM).

z Roaming

Provides seamless roaming within the IEEE 802.11b (11M) and IEEE 802.11g (54M)
WLAN infrastructure.

z IEEE 802.11b compatible (11M)

Allowing inter-operation among multiple vendors.

z IEEE 802.11g compatible (54M)

Allowing inter-operation among multiple vendors.

z Auto fallback

54M, 48M, 36M, 24M, 18M, 12M, 6M data rate with auto fallback in 802.11g mode.

11M, 5.5M, 2M, 1M data rate with auto fallback in 802.11b mode.

Security functions

z Packet filter supported

Packet Filter allows you to control access to a network by analyzing the incoming and

outgoing packets and letting them pass or halting them based on the IP address of the source
and destination.

z Domain Filter Supported

Let you prevent users under this device from accessing specific URLs.

z URL Blocking Supported

URL Blocking can block hundreds of websites connection by simply a keyword.

z VPN Pass-through

The router also supports VPN pass-through.

z 802.1X supported

When the 802.1X function is enabled, the Wireless user must authenticate to this router first
to use the Network service.

z Support WPA-PSK and WPA version 1 and 2
When the WPA function is enabled, the Wireless user must authenticate to this router first to

use the Network service

z SPI Mode Supported

When SPI Mode is enabled, the router will check every incoming packet to detect if this
packet is valid.

z DoS Attack Detection Supported

4

When this feature is enabled, the router will detect and log the DoS attack comes from the
Internet.

Advanced functions

z System time Supported

Allow you to synchronize system time with network time server.

z E-mail Alert Supported

The router can send its info by mail.

z Dynamic dns Supported

At present,the router has 3 ddns.dyndns,TZO.com and dhs.org.

z SNMP Supported

The router supports basic SNMP function.

z Routing Table Supported

Now, the router supports static routing.

z Schedule Rule supported

Customers can control some functions, like virtual server and packet filters when to access or
when to block.

Other functions

z UPNP (Uni versal Plug and Play)Supported

The router also supports this function. The applications: X-box, Msn Messenger.

Packing List

z Wireless broadband r outer unit
z Installation CD-ROM

z Power adapter
z CAT-5 UTP Fast Ethernet cable

5

2.1 Panel Layout

2.1.1. Front Panel

C

C

C

h

a

p

t

e

r

2

H

a

r

d

w

a

r

e

I

n

s

t

a

l

l

a

t

i

o

h

a

p

t

e

r

2

H

a

r

d

w

a

r

e

I

n

s

t

h

a

p

t

e

r

2

H

a

r

d

w

a

r

e

a

I

n

s

t

a

n

l

l

a

t

i

o

n

l

l

a

t

i

o

n

Figure 2-1 Front Panel

LED: Ports:

Port Description
PWR
WAN

Port 1-4

Power inlet
the port where you will connect your cable (or DSL) modem or

Ethernet router.
the ports where you will connect networked computers and other

devices.

6

2.1.2. Rear Panel

Figure 2-2 Rear Panel

LED:

LED Function Color Status Description

Power

Status

WAN

WLAN

Link.
1~4

Speed

Power
indication
System
status
WAN port
activity

Wireless
activity

Link status Green On

Green On Power is being applied to this product.

Green Blinking

Green On The WAN port is linked.

Green

Blinking The WAN port is sending or receiving data.

Blinking Sending or receiving data via wireless

Blinking

Status is flash ed once per second to indicate system is
alive.

An active station is connected to the corresponding
LAN port.
The corresponding LAN port is sending or receiving
data.

10/100 Data Rate Green

On

Reset To reset system settings to factory defaults

Data is transmitting in 100Mbps on the corresponding
LAN port.

2.2 Procedure for Hardware Installation

2. Decide where to place your Wireless Broadband Router

7

You can place your Wireless Broadband Router on a desk or other flat surface, or you can mount it
on a wall. For optimal performance, place your Wireless Broadband Router in the center of your
office (or your home) in a location that is away from any potential source of interference, such as a
metal wall or microwave oven. This location must be close to power and network connection.

2. Setup LAN connection

a. Wired LAN connection: connects an Ethernet cable from your computer’s Ethernet port to one

of the LAN ports of this product.

b. Wireless LAN connection: locate this product at a proper position to gain the best transmit

performance.

Figure 2-3 Setup of LAN and WAN connections for this product.

3. Setup WAN connection

Prepare an Ethernet cable for connecting this product to your cable/xDSL modem or Ethernet
backbone. Figure 2-3 illustrates the WAN connection.

4. Power on

Connecting the power cord to power inlet and turning the power switch on, this product will
automatically enter the self-test phase. When it is in the self-test phase, the indicators M1 will be
lighted ON for about 10 seconds, and then M1 will be flashed 3 times to indicate that the self-test
operation has finished. Finally, the M1 will be continuously flashed once per second to indicate
that this product is in normal operation.

8