MLC21AAM
General
Descriptions:
FCC ID : PBLMLC21AAM
802.11ac/abgnDual-Band
The MLC21AAM is a highly integrated module which has built in a 2x2 dual-band
wireless LAN radio. It supports IEEE 802.11ac draft standard and provides the highest
PHY rate up to 867Mbps, offering feature-rich wireless connectivity and reliable
throughput from an extended distance. Optimized RF architecture and baseband algorithms
provide superb performance and low power consumption. MLC21AAM integrates
A/LNA such that the number of the external components is reduced to minimum.
P
Intelligent MAC design deploys a high efficient DMA engine and hardware data
processing accelerators which offloads the host processor. The MLC21AAM supports the
802.11i security standard and implements hardware acceleration for TKIP, CCMP and
WAPI.
WLAN Base band
MLC21AAM baseband supports the following features:
11ac stage-1 feature support
20, 40, and 80MHz channels
MCS0-7 (BPSK, r=1/2 through 64QAM, r=5/6)
MCS8-9 (256QAM, r=3/4 and r=5/6)
VHT A-MPDU delimiter for RX and TX for single MPDU
Clear Channel Assessment (CCA) on secondary
Short Guard Interval
STBC support
Low Density Parity check (LDPC) coding
Support digital pre-distortion to enhance PA performance
Smoothing (channel estimation) extension to MIMO case
Dynamic frequency selection (DFS) radar pulse detection
WLANRF
MLC21AAM RF supports the following features:
tegrated 2.4GHz/5GHz PA and LNA
In
Integrated 5GHz Balun
Support 2.4GHz/5GHz external PA and LNA
Improve the efficiency of RF PA with Digital Pre-Distortion (DPD)
Improve the power variation with TSSI compensated TX power control
GENERAL
IEEE WLAN Standard
IEEE 802.11 a/b/g/n and 802.11ac draft compliant
Support 20MHz, 40MHz, 80MHz in 5GHz band, and 20MHz, 40MHz bandwidth in 2.4GHz band
Dual-band 2T2R mode with data rate up to 867Mbps
Support 256QAM in 2.4GHz band
Support STBC, LDPC, MRC, and transmit Beamforming
Greenfield, mixed mode, legacy modes support
Frame aggregation
Integrated LNA, PA, and T/R switch.
Optional external LNA and PA support.
IEEE 802.11 d/e/h/i/k/r/w support
Security support for WFA WPA/WPA2 personal, WPS2.0, WAPI
Supports 802.11w protected managed frames
QoS support of WFA WMM, WMM PS
802.11 to 802.3 header translation offload
Supports Wi-Fi Direct
Per packet transmit power control
Wake on WLAN
1
SECURITYFEATURES
1
Support for WFAWPA/WPA2 personal, WPS2.0, WAPI
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FOR MOBILE DEVICE USAGE (>20cm/low power eg. AP routers
Radiation ExposureStatement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator & your body.
FOR COUNTRY CODE SELECTION USAGE (WLAN DEVICES)
Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all
WiFi product marketed in US must fixed to US operation channels only.
)
This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the
following conditions must be strictly followed when using this certified module:
KDB 996369 D03 OEM Manual v01 rule sections:
2.2 List of applicable FCC rules
This module has been tested for complianceto FCC Part 15
2.3 Summarize the specific operational use conditions
The module is tested for standalone mobile RF exposure use condition. Any other usage conditions such as
co-location with other transmitter(s) or being used in a portable condition will need a separate
reassessment through a class II permissive change application or new certification.
2.4 Limited module procedures
Not applicable.
2.5 Trace antenna designs
Not applicable.
2.6 RF exposure considerations
This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20cm between
the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required
to confirm compliance with relevant FCC portable RF exposure rules.
2.7 Antennas
The following antennas have been certified for use with this module; antennas of the same type with equal or
lower gain may also be used with this module. The antenna must be installed such that 20 cm can be maintained
between the antenna and users.
2.8 Label and compliance information
The final end product must be labeled in a visible area with the following: “Contains FCC ID:PBLMLC21AAM.The
grantee's FCC ID can be used only when all FCC compliance requirements are met.
2.9 Information on test modes and additional testing requirements
This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous
transmission with other transmitter(s) or portable use will require a separate class II permissive change reevaluation or new certification.
2.10 Additional testing, Part 15 Subpart B disclaimer
This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart
B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be
reassessed for compliance to this portion of rule requirements if applicable.
As long as all conditions above are met, further transmittertest will not be required. However, the
OEM integrator is still responsible for testing their end-product for any additional compliance
requirements required with this module installed.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no longer considered
valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or
remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
OEM/Host manufacturer responsibilities
OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final
product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15
SubpartBbeforeitcanbeplacedontheUSmarket.Thisincludesreassessingthetransmittermodulefor compliance
with the Radio and EMF essential requirements of the FCC rules. This module must not be incorporated into
any other device or system without retesting for compliance as multi-radio and combined equipment.
Loading...