Advanced Technology International USA M200 User Manual

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

M200 Series Copier Controller

Product Overview

The M200 Series Copier Controller accepts one coin to vend one copy. That coin can
be a nickel (M205), dime (M210) or quarter (M225).

The M200 Series Controller's housing - similar to a tall and narrow "breadbox" ­allows for easy mounting on any of its three non-faceplate sides.

The M200 Series Controller runs safely off the low signal voltages of its attached
copier, and comes standard with both a copier specific sprig and bypass keyswitch.

Technical Specifications

• Accommodates 5 VDC to 30 VDC signals from copier

• Rugged tubular lock

• $70 cashbox capacity

• Dimensions: 16.5" x 5.75" x 6"

• Weight: 12 lb

Warranty

The M200 is warrantied against manufacturing defects for a period of one year from
date of shipment, to be determined by the serial number on the inside of its housing.

To honor legitimate warranty claims, Advanced Technologies (TekVend) agrees to
repair or replace at its discretion any M200 Series Controller found defective for
manufacturing defects within the warranty period specified. Advanced Technologies
(TekVend) additionally agrees to pay ground return shipping and insurance on these
warranty repairs or replacements.

Advanced Technologies (TekVend) cannot be responsible for any damage that occurs
to product returned to it due to inadequate return shipment procedures. The shipper
is responsible for ensuring that return shipment packaging is adequate and that the
return shipment is adequately insured.

Advanced Technologies (TekVend) does not warranty its product for damage caused
by abusive use, vandalism, improper installation, and improper field repair. Installer
is expected to use the original copier specific harness (sprig) supplied by Advanced
Technologies (TekVend), and install the M200 on the originally specified copier,
unless otherwise authorized.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

M6000 CreditVend Copier / Printer Controller

Product Overview

The M6000 CreditVend Copier / Printer Controller accepts nickels, dimes, quarters,
and dollar coins to vend one or more images, depending on the amount of monetary
value (credit) not yet spent.

One price is available for all image types.

The M6000 employs SmartCoin technology to ensure that change is always
available for every conceivable vending situation.

Foreign coin mechanisms are available for select countries. Please contact us for
foreign vending applications.

Electromechanical Features

• Two-line backlit user-friendly LCD display

• Two pushbutton switches for programming and readouts

• Red "message" light

• Semi-gloss enamel finish resists marring, scratches

• High security tubular housing lock

• Bypass keyswitch for free copies

• Bent coin return and change request plunger

• Large coin return cup

• Standard copier specific harness (sprig) included

• Large cash box ($900 capacity)

• Single board, single chip design

• Three tube MDB changer (N, D, Q, $1 Coin, $41 capacity)

• Optional five tube US-Canadian MDB changer (N, D, Q, $1 Coin, $82

maximum capacity)

Software Features

• SmartCoin technology assures that change is always available for every

• Controller uses safe low voltage (24 VAC)

The M6000 is warrantied against manufacturing defects for a period of two years

conceivable vending situation

• User-friendly instructions during vending, programming and readouts

• Exact change and error messages indicated by blinking red LED

• Seamless transition to and from exact change mode ensures that controller

"works out of the box"

• Resettable counter allows user to monitor copying by copies per original, or
total copies made per vend cycle

• AccumaVend technology allows user to add monetary value "on the fly" i.e.
while copies are being made

• Time delay reset (TDR) ensures full copy imaging on last full copy credit

• Anti-cheating timeout delay monitors for late copy counts after change return

request made

• Readouts show current (resettable) and cumulative (nonresettable) vend and
bypass copies totals

Technical Specifications

• Controller totally isolated from copier / printer

• Controller works on most all copiers and with most copier signals

• Canadian coin acceptance switch selectable with high capacity changer

• Two key coin inventory system adds measure of security

• Dimensions: 25.5" x 16" x 5.5"

• Weight: 42 lb

Warranty

from date of shipment, to be determined by the serial number on its main board's

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

microchip. Warranties for components of the M6000, if different, supercede this

general warranty.

Specifically, the standard MDB changer is warrantied against manufacturing
defects for a period of two years from date of manufacture, to be determined from
the first four digits of its serial number (wwyy).

Additionally, the optional MDB changer is warrantied against manufacturing
defects for a period of three years from date of manufacture, to be determined
from the first four digits of its serial number (wwyy).

Advanced Technologies (TekVend) agrees to repair or replace at its discretion any
of the above items within the warranty periods specified for them. Advanced
Technologies (TekVend) agrees to pay ground return shipping and insurance on all
warranty repair or replacements.

Advanced Technologies (TekVend) cannot be responsible for any damage that
occurs to product returned to it due to inadequate return shipment procedures.
The shipper is responsible for ensuring that return shipment packaging is
adequate and that the return shipment is adequately insured.

Advanced Technologies (TekVend) does not warranty its product for damage
caused by abusive use, vandalism, improper installation, and improper field
repair. Installer is expected to use the original copier specific harness (sprig)
supplied by Advanced Technologies (TekVend), and install the M6000 on the
originally specified copier, unless otherwise authorized

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

M6500 CreditVend Copier / Printer Controller

Product Overview

The M6500 CreditVend Copier / Printer Controller accepts nickels, dimes, quarters,
dollar coins and $1 and $5 bills to vend one or more images, depending on the
amount of monetary value (credit) not yet spent.

One price is available for all image types.

The M6500 employs SmartCoin technology to ensure that change is always
available for every conceivable vending situation.

Foreign coin mechanisms and bill validators are available for select countries. Please
contact us for foreign vending applications.

Electromechanical Features

• Two-line backlit user-friendly LCD display

• Two pushbutton switches for programming and readouts

• Red "message" light

• Semi-gloss enamel finish resists marring, scratches

• High security tubular housing lock

• Bypass keyswitch for free copies

• Bent coin return and change request plunger

• Large coin return cup

• Safe 24 VAC external power supply included

• Standard copier specific harness (sprig) included

• Large cash box ($900 capacity)

• Single board, single chip design

• Three tube MDB changer (N, D, Q, $1 Coin, $41 capacity)

• Optional five tube US-Canadian MDB changer (N, D, Q, $1 Coin, $82

maximum capacity)

• Self diagnostic MDB bill validator ($1 and $5 bills, $500 capacity)

Software Features

• SmartCoin technology assures that change is always available for every

• Controller uses safe low voltage (24 VAC)

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

conceivable vending situation

• SmartCoin technology dynamically controls bill type acceptance based on
maximum credit allowed, and change available

• User-friendly instructions during vending, programming and readouts

• Exact change and error messages indicated by blinking red LED

• Seamless transition to and from exact change mode ensures that controller

"works out of the box"

• Resettable counter allows user to monitor copying by copies per original, or
total copies made per vend cycle

• AccumaVend technology allows user to add monetary value "on the fly" i.e.
while copies are being made

• Time delay reset (TDR) ensures full copy imaging on last full copy credit

• Anti-cheating timeout delay monitors for late copy counts after change return

request made

• Readouts show current (resettable) and cumulative (nonresettable) vend and
bypass copies totals

Technical Specifications

• Controller totally isolated from copier / printer

• Controller works on most all copiers and with most copier signals

• Canadian coin acceptance switch selectable with high capacity changer

• Two key coin inventory system adds measure of security

• Dimensions: 25.5" x 16" x 5.5"

• Weight: 46 lb

Warranty

The M6500 is warrantied against manufacturing defects for a period of two years

from date of shipment, to be determined by the serial number on its main board's
microchip. Warranties for components of the M6500, if different, supercede this
general warranty.

Specifically, the standard MDB changer is warrantied against manufacturing
defects for a period of two years from date of manufacture, to be determined from
the first four digits of its serial number (wwyy).

Additionally, the optional MDB changer is warrantied against manufacturing
defects for a period of three years from date of manufacture, to be determined
from the first four digits of its serial number (wwyy).

The bill validator is warrantied against manufacturing defects for a period of three
years from date of manufacture, to be determined from the first four digits of its
serial number (wwyy).

Advanced Technologies (TekVend) agrees to repair or replace at its discretion any
of the above items within the warranty periods specified for them. Advanced
Technologies (TekVend) agrees to pay ground return shipping and insurance on all
warranty repair or replacements.

Advanced Technologies (TekVend) cannot be responsible for any damage that
occurs to product returned to it due to inadequate return shipment procedures.
The shipper is responsible for ensuring that return shipment packaging is
adequate and that the return shipment is adequately insured.

Advanced Technologies (TekVend) does not warranty its product for damage
caused by abusive use, vandalism, improper installation, and improper field
repair. Installer is expected to use the original copier specific harness (sprig)
supplied by Advanced Technologies (TekVend), and install the M6500 on the
originally specified copier, unless otherwise authorized.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

M6506 CreditVend Copier / Printer Controller

Product Overview

The M6506 CreditVend Copier / Printer Controller accepts nickels, dimes, quarters,
dollar coins and $1 and $5 bills to vend one or more images, depending on the
amount of monetary value (credit) not yet spent.

Six prices are available to support up to six image types e.g., letter, legal and ledger,
for black and white, or full color copies. Other pricing schemes are possible,
depending on copier make and model (e.g., two color, reduction and enlargement,
etc.). The multi-pricing capability of the M6506 can only be used on copiers
supporting mode B or serial communication protocols.

The M6506 employs SmartCoin technology to ensure that change is always
available for every conceivable vending situation.

Foreign coin mechanisms and bill validators are available for select countries. Please
contact us for foreign vending applications.

Electromechanical Features

• Two-line backlit user-friendly LCD display

• Two pushbutton switches for programming and readouts

• Red "message" light

• Semi-gloss enamel finish resists marring, scratches

• High security tubular housing lock

• Bypass keyswitch for free copies

• Bent coin return and change request plunger

• Large coin return cup

• Safe 24 VAC external power supply included

• Standard copier specific harness (sprig) included

• Large cash box ($900 capacity)

• Single board, single chip design

• Three tube MDB changer (N, D, Q, $1 Coin, $41 capacity)

• Optional five tube US-Canadian MDB changer (N, D, Q, $1 Coin, $82

maximum capacity)

• Self diagnostic MDB bill validator ($1 and $5 bills, $500 capacity)

Software Features

• SmartCoin technology assures that change is always available for every

• Controller uses safe low voltage (24 VAC)

• Fully compatible with Ricoh Aficio, Xerox and Minolta color copiers

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

conceivable vending situation

• SmartCoin technology dynamically controls bill type acceptance based on
maximum credit allowed, and change available

• User-friendly instructions during vending, programming and readouts

• Exact change and error messages indicated by blinking red LED

• Seamless transition to and from exact change mode ensures that controller

"works out of the box"

• Resettable counter allows user to monitor copying by copies per original, or
total copies made per vend cycle

• AccumaVend technology allows user to add monetary value "on the fly" i.e.
while copies are being made

• Time delay reset (TDR) ensures full copy imaging on last full copy credit

• Anti-cheating timeout delay monitors for late copy counts after change return

request made

• Readouts show current (resettable) and cumulative (nonresettable) vend and
bypass copies totals by copy type (A through F)

Technical Specifications

• Controller totally isolated from copier / printer

• Controller works on most all copiers and with most copier signals

• Canadian coin acceptance switch selectable with high capacity changer

• Two key coin inventory system adds measure of security

• Dimensions: 25.5" x 16" x 5.5"

• Weight: 46 lb

The M6506 is warrantied against manufacturing defects for a period of two years

Warranty

from date of shipment, to be determined by the serial number on its main board's
microchip. Warranties for components of the M6506, if different, supercede this
general warranty.

Specifically, the standard MDB changer is warrantied against manufacturing
defects for a period of two years from date of manufacture, to be determined from
the first four digits of its serial number (wwyy).

Additionally, the optional MDB changer is warrantied against manufacturing
defects for a period of three years from date of manufacture, to be determined
from the first four digits of its serial number (wwyy).

The bill validator is warrantied against manufacturing defects for a period of three
years from date of manufacture, to be determined from the first four digits of its
serial number (wwyy).

Advanced Technologies (TekVend) agrees to repair or replace at its discretion any
of the above items within the warranty periods specified for them. Advanced
Technologies (TekVend) agrees to pay ground return shipping and insurance on all
warranty repair or replacements.

Advanced Technologies (TekVend) cannot be responsible for any damage that
occurs to product returned to it due to inadequate return shipment procedures.
The shipper is responsible for ensuring that return shipment packaging is
adequate and that the return shipment is adequately insured.

Advanced Technologies (TekVend) does not warranty its product for damage
caused by abusive use, vandalism, improper installation, and improper field
repair. Installer is expected to use the original copier specific harness (sprig)
supplied by Advanced Technologies (TekVend), and install the M6506 on the
originally specified copier, unless otherwise authorized.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

M7500 CreditVend Copier / Printer Controller

Product Overview

The M7500 CreditVend Copier / Printer Controller accepts nickels, dimes, quarters,
dollar coins, $1, $2, $5, $10 and $20 bills and proprietary magnetic debit cards to
vend one or more images, depending on the amount of monetary or card value
(credit) not yet spent. The M7500 comes standard with a high capacity premium
changer.

One price is available for all image types.

The M7500 employs SmartCoin technology to ensure that change is always
available for every conceivable vending situation. Value can be added to cards, and
value on cards can be used to make images, but value on cards cannot be converted
to money.

Foreign coin mechanisms and bill validators are available for select countries. Please
contact us for foreign vending applications.

Electromechanical Features

• Two-line backlit user-friendly LCD display

• Two pushbutton switches for programming and readouts

• Red "message" light

• Semi-gloss enamel finish resists marring, scratches

• High security tubular housing lock

• Bypass keyswitch for free copies

• Bent coin return and change request plunger

• Large coin return cup

• Safe 24 VAC external power supply included

• Standard copier specific harness (sprig) included

• Large cash box ($900 capacity)

• Single board, single chip design

• Five tube US-Canadian MDB changer (N, D, Q, $1 Coin, $82 maximum

capacity) standard

• Self diagnostic MDB bill validator ($1, $2, $5, $10 and $20 Bills, $500
capacity)

• Card programmable MDB card reader for making, revaluing and using debit
cards

Software Features

• SmartCoin technology assures that change is always available for every

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

conceivable vending situation

• SmartCoin technology dynamically controls bill type acceptance based on
maximum credit allowed, and change available

• User-friendly instructions during vending, programming and readouts

• Exact change and error messages indicated by blinking red LED

• Seamless transition to and from exact change mode ensures that controller

"works out of the box"

• Resettable counter allows user to monitor copying by copies per original, or
total copies made per vend cycle

• AccumaVend technology allows user to add monetary value "on the fly" i.e.
while copies are being made

• In card mode, unused credit is always returned to card

• In card mode, copier / printer use privileges are determined by a group

number field stored on the card

• Virginal cards can be initialized for group number and value directly on the
controller

• Card revaluation can be turned off

• Card vend price can be different than cash vend price

• Time delay reset (TDR) ensures full copy imaging on last full copy credit

• Anti-cheating timeout delay monitors for late copy counts after change return

request made

• Readouts show current (resettable) and cumulative (nonresettable) vend and
bypass copies totals

Technical Specifications

• Controller uses safe low voltage (24 VAC)

The M7500 is warrantied against manufacturing defects for a period of two years

• Controller totally isolated from copier / printer

• Controller works on most all copiers and with most copier signals

• Canadian coin acceptance switch selectable with high capacity changer

• Two key coin inventory system adds measure of security

• Dimensions: 25.5" x 16" x 5.5"

• Weight: 46 lb

Warranty

from date of shipment, to be determined by the serial number on its main board's
microchip. Warranties for components of the M7500, if different, supercede this
general warranty.

Specifically, the MDB changer is warrantied against manufacturing defects for a
period of three years from date of manufacture, to be determined from the first
four digits of its serial number (wwyy).

The bill validator is warrantied against manufacturing defects for a period of two
years from date of manufacture, to be determined from the first four digits of its
serial number (wwyy).

Note that the card reader is warrantied against manufacturing defects for a period
of one year from date of shipment, to be determined by the serial number on the
card reader itself.

Advanced Technologies (TekVend) agrees to repair or replace at its discretion any
of the above items within the warranty periods specified for them. Advanced
Technologies (TekVend) agrees to pay ground return shipping and insurance on all
warranty repair or replacements.

Advanced Technologies (TekVend) cannot be responsible for any damage that
occurs to product returned to it due to inadequate return shipment procedures.
The shipper is responsible for ensuring that return shipment packaging is
adequate and that the return shipment is adequately insured.

Advanced Technologies (TekVend) does not warranty its product for damage
caused by abusive use, vandalism, improper installation, and improper field
repair. Installer is expected to use the original copier specific harness (sprig)
supplied by Advanced Technologies (TekVend), and install the M7500 on the
originally specified copier, unless otherwise authorized.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

M7506 CreditVend Copier / Printer Controller

Product Overview

The M7506 CreditVend Copier / Printer Controller accepts nickels, dimes, quarters,
dollar coins, $1, $2, $5, $10 and $20 bills and proprietary magnetic debit cards to
vend one or more images, depending on the amount of monetary or card value
(credit) not yet spent. The M7506 comes standard with a high capacity premium
changer.

Six prices are available to support up to six image types e.g., letter, legal and ledger,
for black and white, or full color copies. Other pricing schemes are possible,
depending on copier make and model (e.g., two color, reduction and enlargement,
etc.). The multi-pricing capability of the M7506 can only be used on copiers
supporting mode B or serial communication protocols.

The M7506 employs SmartCoin technology to ensure that change is always
available for every conceivable vending situation. Value can be added to cards, and
value on cards can be used to make images, but value on cards cannot be converted
to money.

Foreign coin mechanisms and bill validators are available for select countries. Please
contact us for foreign vending applications.

Electromechanical Features

• Two-line backlit user-friendly LCD display

• Two pushbutton switches for programming and readouts

• Red "message" light

• Semi-gloss enamel finish resists marring, scratches

• High security tubular housing lock

• Bypass keyswitch for free copies

• Bent coin return and change request plunger

• Large coin return cup

• Safe 24 VAC external power supply included

• Standard copier specific harness (sprig) included

• Large cash box ($900 capacity)

• Single board, single chip design

• Five tube US-Canadian MDB changer (N, D, Q, $1 Coin, $82 maximum

capacity) standard

• Self diagnostic MDB bill validator ($1, $2, $5, $10 and $20 Bills, $500
capacity)

• Card programmable MDB card reader for making, revaluing and using debit
cards

Software Features

• SmartCoin technology assures that change is always available for every

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

conceivable vending situation

• SmartCoin technology dynamically controls bill type acceptance based on
maximum credit allowed, and change available

• User-friendly instructions during vending, programming and readouts

• Exact change and error messages indicated by blinking red LED

• Seamless transition to and from exact change mode ensures that controller

"works out of the box"

• Resettable counter allows user to monitor copying by copies per original, or
total copies made per vend cycle

• AccumaVend technology allows user to add monetary value "on the fly" i.e.
while copies are being made

• In card mode, unused credit is always returned to card

• In card mode, copier / printer use privileges are determined by a group

number field stored on the card

• Virginal cards can be initialized for group number and value directly on the
controller

• Card revaluation can be turned off

• Card vend price can be different than cash vend price

• Time delay reset (TDR) ensures full copy imaging on last full copy credit

• Anti-cheating timeout delay monitors for late copy counts after change return

request made

• Readouts show current (resettable) and cumulative (nonresettable) vend and
bypass copies totals by copy type (A through F)

Technical Specifications

• Controller uses safe low voltage (24 VAC)

The M7506 is warrantied against manufacturing defects for a period of two years

• Controller totally isolated from copier / printer

• Controller works on most all copiers and with most copier signals

• Fully compatible with Ricoh Aficio, Xerox and Minolta color copiers

• Canadian coin acceptance switch selectable with high capacity changer

• Two key coin inventory system adds measure of security

• Dimensions: 25.5" x 16" x 5.5"

• Weight: 46 lb

Warranty

from date of shipment, to be determined by the serial number on its main board's
microchip. Warranties for components of the M7506, if different, supercede this
general warranty.

Specifically, the MDB changer is warrantied against manufacturing defects for a
period of three years from date of manufacture, to be determined from the first
four digits of its serial number (wwyy).

The bill validator is warrantied against manufacturing defects for a period of two
years from date of manufacture, to be determined from the first four digits of its
serial number (wwyy).

Note that the card reader is warrantied against manufacturing defects for a period
of one year from date of shipment, to be determined by the serial number on the
card reader itself.

Advanced Technologies (TekVend) agrees to repair or replace at its discretion any
of the above items within the warranty periods specified for them. Advanced
Technologies (TekVend) agrees to pay ground return shipping and insurance on all
warranty repair or replacements.

Advanced Technologies (TekVend) cannot be responsible for any damage that
occurs to product returned to it due to inadequate return shipment procedures.
The shipper is responsible for ensuring that return shipment packaging is
adequate and that the return shipment is adequately insured.

Advanced Technologies (TekVend) does not warranty its product for damage
caused by abusive use, vandalism, improper installation, and improper field
repair. Installer is expected to use the original copier specific harness (sprig)
supplied by Advanced Technologies (TekVend), and install the M7506 on the
originally specified copier, unless otherwise authorized.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

M Series Copier / Printer Controller Optional Components

High capacity

US-Canadian changer

Full body decal

[Minimum order - 50 pcs]

Floor mounting pedestal

Lockable cash box

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

AC500 Bill Changer

Product Overview

Advanced Technologies offers a complete line of bill changers for bulk changing of
paper currency into coins. US bills can be changed into quarters or dollar coins. Box
integrity is assured with full body hinge and screw type lock.

Technical Specifications

• Single hopper

• Bill acceptor takes $1, $2 and $5 bills

• Stacker capacity of 450 bills

• Hopper capacity of 1000 quarters

• Dimensions of 8.5" W X 18" H X 10" D

• Weight of 37 lb

• Optional $1 coin hopper with 800 coin capacity

Warranty

The AC bill changers are warrantied against manufacturing defects for a period of
two years from date of shipment, to be determined by the serial number on its main
board's microchip. Warranties for components of the AC bill changers, if different,
supercede this general warranty.

Specifically, the MDB changer is warrantied against manufacturing defects for a
period of three years from date of manufacture, to be determined from the first four
digits of its serial number (wwyy).

The bill validator is warrantied against manufacturing defects for a period of two
years from date of manufacture, to be determined from the first four digits of its
serial number (wwyy).

Note that the card reader is warrantied against manufacturing defects for a period of
one year from date of shipment, to be determined by the serial number on the card
reader itself.

Advanced Technologies (TekVend) agrees to repair or replace at its discretion any of
the above items within the warranty periods specified for them. Advanced
Technologies (TekVend) agrees to pay ground return shipping and insurance on all
warranty repair or replacements.

Advanced Technologies (TekVend) cannot be responsible for any damage that occurs
to product returned to it due to inadequate return shipment procedures. The shipper
is responsible for ensuring that return shipment packaging is adequate and that the
return shipment is adequately insured.

Advanced Technologies (TekVend) does not warranty its product for damage caused
by abusive use, vandalism, improper installation, and improper field repair.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

AC1001 Bill Changer

Product Overview

Advanced Technologies offers a complete line of bill changers for bulk changing of
paper currency into coins. US bills can be changed into quarters or dollar coins. Box
integrity is assured with full body hinge and screw type lock.

Technical Specifications

• Single hopper

• Bill acceptor takes $1, $2, $5, $10 and $20 bills

• Stacker capacity of 450 bills

• Hopper capacity of 2800 quarters / tokens OR 2200 $1 coins

• Dimensions of 8.5" W X 26" H X 13" D

• Weight of 58 lb

Warranty

The AC bill changers are warrantied against manufacturing defects for a period of
two years from date of shipment, to be determined by the serial number on its main
board's microchip. Warranties for components of the AC bill changers, if different,
supercede this general warranty.

Specifically, the MDB changer is warrantied against manufacturing defects for a
period of three years from date of manufacture, to be determined from the first four
digits of its serial number (wwyy).

The bill validator is warrantied against manufacturing defects for a period of two
years from date of manufacture, to be determined from the first four digits of its
serial number (wwyy).

Note that the card reader is warrantied against manufacturing defects for a period of
one year from date of shipment, to be determined by the serial number on the card
reader itself.

Advanced Technologies (TekVend) agrees to repair or replace at its discretion any of
the above items within the warranty periods specified for them. Advanced
Technologies (TekVend) agrees to pay ground return shipping and insurance on all
warranty repair or replacements.

Advanced Technologies (TekVend) cannot be responsible for any damage that occurs
to product returned to it due to inadequate return shipment procedures. The shipper
is responsible for ensuring that return shipment packaging is adequate and that the
return shipment is adequately insured.

Advanced Technologies (TekVend) does not warranty its product for damage caused
by abusive use, vandalism, improper installation, and improper field repair.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

AC2001 Bill Changer

Product Overview

Advanced Technologies offers a complete line of bill changers for bulk changing of
paper currency into coins. US bills can be changed into quarters or dollar coins. Box
integrity is assured with full body hinge and screw type lock.

Technical Specifications

• Dual hopper

• Bill acceptor takes $1, $2, $5, $10 and $20 bills

• Stacker capacity of 1000 bills

• 2 hoppers that can dispense either all quarters [2800 / hopper], all $1 coins

[2200 / hopper], or 1 hopper of each.

• Dimensions of 13.5" W X 26" H X 13" D

• Weight of 91 lb

Warranty

The AC bill changers are warrantied against manufacturing defects for a period of
two years from date of shipment, to be determined by the serial number on its main
board's microchip. Warranties for components of the AC bill changers, if different,
supercede this general warranty.

Specifically, the MDB changer is warrantied against manufacturing defects for a
period of three years from date of manufacture, to be determined from the first four
digits of its serial number (wwyy).

The bill validator is warrantied against manufacturing defects for a period of two
years from date of manufacture, to be determined from the first four digits of its
serial number (wwyy).

Note that the card reader is warrantied against manufacturing defects for a period of
one year from date of shipment, to be determined by the serial number on the card
reader itself.

Advanced Technologies (TekVend) agrees to repair or replace at its discretion any of
the above items within the warranty periods specified for them. Advanced
Technologies (TekVend) agrees to pay ground return shipping and insurance on all
warranty repair or replacements.

Advanced Technologies (TekVend) cannot be responsible for any damage that occurs
to product returned to it due to inadequate return shipment procedures. The shipper
is responsible for ensuring that return shipment packaging is adequate and that the
return shipment is adequately insured.

Advanced Technologies (TekVend) does not warranty its product for damage caused
by abusive use, vandalism, improper installation, and improper field repair.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

Copicode Alpha Copier / Printer Controller

Product Overview

The Copicode Alpha Copier / Printer Controller is a fully alphanumeric keypad
controller designed to vend images against accounting quotas associated with users,
departments and projects.

The Alpha comes standard with approximately 1500 codes, but can be easily
expanded in multiples of 1500 codes, up to a maximum of 6000 codes.

The device supports two and a half levels of accounting [with the optional P200N
printer], or three levels of accounting [with Copy-Track
user codes].

The Alpha supports individual prices for up to four different image types, depending
on copier / printer make and model. The Alpha stores 10 different quotas for limiting
imaging activity by user or project.

The Alpha can be configured for different keypad operation modes. Specifically, it
can be set up for open accounting third party (client / matter) billing, a mode
favored by the legal profession.

The Alpha has four speed buttons and four navigational arrows for quick and easy
administrative programming. When used with Copy-Track software, four sets of
prices are supported across a group of copiers.

With Copy-Track software, usage statistics can be downloaded, and codes uploaded,
manually or serially, using either a laptop or similar device, or a network connection.

The Alpha comes standard with its own 24 VDC power supply, but it can run off
power from the copier / printer in many cases. It is shipped with a copier / printer
specific sprig at no extra charge.

The Alpha has a small footprint, measuring only 4" x 2.5" x 7", and weighs a mere 1
lb. It comes with a one year (from date of shipment) warranty for manufacturing
defects.

®

software, using segmented

Warranty

The Copicode Alpha is warrantied against manufacturing defects for a period of one
year from date of shipment, to be determined by the serial number on its back and
an internal serial number.

Advanced Technologies (TekVend) agrees to repair or replace an Alpha shown to
have manufacturing defects within its warranty period. Advanced Technologies
(TekVend) agrees to pay ground return shipping and insurance on these warranty
repairs or replacements.

Advanced Technologies (TekVend) cannot be responsible for any damage that occurs
to product returned to it due to inadequate return shipment procedures. The shipper
is responsible for ensuring that return shipment packaging is adequate and that the
return shipment is adequately insured.

Advanced Technologies (TekVend) does not warranty its product for damage caused
by abusive use, vandalism, improper installation, and improper field repair. Installer
is expected to use the original copier specific harness (sprig) supplied by Advanced
Technologies (TekVend), and install the Copicode Alpha on the originally specified
copier, unless otherwise authorized.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

Copicode Alpha-X Copier / Printer Controller

Product Overview

The Copicode Alpha-X Copier / Printer Controller is a fully alphanumeric keypad
controller designed to vend images against accounting quotas associated with users,
departments and projects. It is functionally the same as the Copicode Alpha, but is
fully ethernet compliant.

The Alpha-X comes standard with approximately 1500 codes, but can be easily
expanded in multiples of 1500 codes, up to a maximum of 6000 codes.

When used in conjunction with Copy-Track
three levels of accounting through the use of segmented user codes.

The Alpha-X supports individual prices for up to four different image types,
depending on copier / printer make and model. The Alpha-X stores 10 different
quotas for limiting imaging activity by user or project. When used with Copy-Track
software, four sets of four prices are supported across a network of copiers.

The Alpha-X can be configured for different keypad operation modes. Specifically, it
can be set up for open accounting third party (client / matter) billing, a mode
favored by the legal profession.

The Alpha-X has four speed buttons and four navigational arrows for quick and easy
administrative programming. When used with Copy-Track software, all programming
can be done remotely, at a PC.

With Copy-Track software, usage statistics can be downloaded, and user codes
uploaded locally to a laptop [using a null ethernet cable], or remotely [using a hub
connection]. Data can be transferred at will, or as a scheduled task. With port
forwarding, or using a link server, Alpha-X controllers can even be polled for data
over the Internet.

With Copy-Track software, copier preventative maintenance calls can be scheduled
from downloaded usage data.

The Alpha-X comes standard with its own 24 VDC power supply, and is shipped with
a copier / printer specific sprig at no extra charge.

The Alpha-X has a small footprint, measuring only 7.75" x 4.25" x 2.5", and weighs a
mere 2 lb. It comes with a one year (from date of shipment) warranty for
manufacturing defects. It is perfect for locations with many copiers, where user
codes must be updated regularly, and manual collection of user data is a significant
expense.

Warranty

®

software, the Alpha-X supports up to

The Copicode Alpha-X is warrantied against manufacturing defects for a period of

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V305.

one year from date of shipment, to be determined by its internal [boot up] serial
number.

Advanced Technologies (TekVend) agrees to repair or replace any Alpha-X shown to
have manufacturing defects within its warranty period. Advanced Technologies
(TekVend) agrees to pay ground return shipping and insurance on these warranty
repairs or replacements.

Advanced Technologies (TekVend) cannot be responsible for any damage that occurs
to product returned to it due to inadequate return shipment procedures. The shipper

is responsible for ensuring that return shipment packaging is adequate and that the

return shipment is adequately insured.

Advanced Technologies (TekVend) does not warranty its product for damage caused
by abusive use, vandalism, improper installation, and improper field repair. Installer
is expected to use the original copier specific harness (sprig) supplied by Advanced
Technologies (TekVend), and install the Copicode Alpha-X on the originally specified
copier, unless otherwise authorized.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V305.

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

TC11N Copier / Printer Controller

Product Overview

The TC11N Copier / Printer Controller is a proprietary magnetic card reader /
encoder that vends images against value stored on reusable or throwaway magnetic
stripe cards.

A special Administrator card is used to initialize and value these cards, and to set
control parameters and prices. Depending on copier / printer make and model, and
copier control mode selected, individual prices for up to four different image types
are supported.

Copier / printer use privileges are determined by group numbers stored both on the
cards and in the TC11N.

Usage statistics can be read out on the TC11N's LCD display.

The TC11N comes standard with its own 24 VDC power supply, but it can run off
power from the copier / printer in many cases. It is shipped with a copier / printer
specific sprig at no extra charge.

The TC11N has a small footprint, measuring only 4" x 3.5" x 7", and weighs a mere 2
lb. It comes with a one year (from date of shipment) warranty for manufacturing
defects.

The M7500 is warrantied against manufacturing defects for a period of one year from

Warranty

date of shipment, to be determined by the serial number at boot up [equal to the
serial number on its back].

Advanced Technologies (TekVend) agrees to repair or replace at its discretion any
TC11N within the warranty period. Advanced Technologies (TekVend) agrees to pay
ground return shipping and insurance on any warranty repair or replacement.

Advanced Technologies (TekVend) cannot be responsible for any damage that occurs
to product returned to it due to inadequate return shipment procedures. The shipper
is responsible for ensuring that return shipment packaging is adequate and that the
return shipment is adequately insured.

Advanced Technologies (TekVend) does not warranty its product for damage caused
by abusive use, vandalism, improper installation, and improper field repair. The
installer is expected to use the original copier specific harness (sprig) supplied by
Advanced Technologies (TekVend), and install the TC11N on the originally specified
copier, unless otherwise authorized.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

Card Types

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

P200N Portable Printer

Product Overview

The P200N portable printer is both a fine standalone printer and a perfect companion
to the Copicode Alpha keypad controller.

The P200N printer is truly portable, powered by an internal Ni-Cd battery pack.
When not in use, the P200N battery pack can be recharged using an external 9VDC
wall adaptor (provided).

The P200N is a serial printer, and thus can be hooked up to the COM port of any
computer or to any RS232 device.

The P200N is a thermal printer, meaning that it prints very quickly and reliably, since
there are no moving parts or ribbons in its print head.

The thermal paper needed is standard-sized, and is very easy to load. Simply drop in
a roll, and close the lid. A convenient serrated blade is built in to the paper
compartment for easy tearing off of printouts. Double thickness thermal paper can
be used when two copies of a printout are needed.

The P200N is easy to program, supports multiple languages, accepts baud rates up
to 38,400, and has three internal fonts supporting up to 42 characters across. It
comes programmed to work "out of the box" with a Copicode Alpha.

An easy-to-follow color manual is supplied, along with two rolls of thermal paper.

Warranty

The P200N is warrantied against manufacturing defects for a period of one year from
date of shipment, to be determined by the serial number on the back of its housing.

To honor legitimate warranty claims, Advanced Technologies (TekVend) agrees to
repair or replace at its discretion any P200N found to have manufacturing defects
within the warranty period specified. Advanced Technologies (TekVend) additionally
agrees to pay ground return shipping and insurance on these warranty repairs or
replacements.

Advanced Technologies (TekVend) cannot be responsible for any damage that occurs
to product returned to it due to inadequate return shipment procedures. The shipper
is responsible for ensuring that return shipment packaging is adequate and that the
return shipment is adequately insured.

Advanced Technologies (TekVend) does not warranty its product for damage caused
by abusive use, vandalism, improper installation, and improper field repair.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

RCT - Remote Control Totalizer

Product Overview

Ideal for the print shop and retail copy sales environments, the Remote Control
Totalizer (RCT) allows an attendant to keep track of copies made on a copier up to
150 feet away. After copies are made and paid for, the attendant simply pushes a
reset button to start the process over again for the next customer. The attendant can
enable or disable the copier at will, using a keyswitch. The key is removable in either
the enable or disable position, and so can be locked out after normal business hours.

Technical Specifications

• Easy to read six digit LCD display

• Powered by two long lasting N cells

• Standard 30 foot cable (can be extended)

• Copier specific harness (sprig) included, with bypass plug

• Count circuitry accommodates 5 to 30 VDC copiers

• Wall or table mountable

• Comes with Velcro attachment tape

• Dimensions: 3" x 3" x 2.5"

• Weight: 1 lb

Warranty

The RCT is warrantied against manufacturing defects for a period of one year from
date of shipment, to be determined by the serial number on the back of its housing.

To honor legitimate warranty claims, Advanced Technologies (TekVend) agrees to
repair or replace at its discretion any RCT found to have manufacturing defects
within the warranty period specified. Advanced Technologies (TekVend) additionally
agrees to pay ground return shipping and insurance on these warranty repairs or
replacements.

Advanced Technologies (TekVend) cannot be responsible for any damage that occurs
to product returned to it due to inadequate return shipment procedures. The shipper
is responsible for ensuring that return shipment packaging is adequate and that the
return shipment is adequately insured.

Advanced Technologies (TekVend) does not warranty its product for damage caused
by abusive use, vandalism, improper installation, and improper field repair. Installer
is expected to use the original copier specific harness (sprig) supplied by Advanced
Technologies (TekVend), and install the RCT on the originally specified copier, unless
otherwise authorized.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

Copy-Track® Controller Software

Product Overview

Copy-Track
and Alpha-X terminals to control and account for copying activity on copiers. Copy­Track manages up to 4200 user codes per copier, and supports up to 999 copiers.

Copy-Track communicates with Alpha terminals via RS232 serial, USB serial,
ethernet, or Palm handheld protocols.

Ethernet communication, local or remote, requires Alpha-X terminals. Both Copicode
Alpha and Alpha-X terminals are fully alphanumeric.

User codes can be up to 16 characters in length, and can be segmented into two or
three parts for higher levels of accounting. User codes can either be pre-entered for
security, or entered "on the fly" for third party billing.

User code names can be up to 25 characters long, and copier names can be up to 16
characters long. User codes and copiers are shown in column sortable tables.
Segments of user codes can be displayed in separate, sortable columns.

Copy-Track has extensive reporting capabilities, especially with segmented user
codes. Reports are based on readings, and are date range selectable. Individual
reports for a user code single segment are also possible: for example, you can
generate a report for one user, by client and matter, or one client, by matter and
user. These individual reports can function as invoices for third party billing. All
reports are fully printable, and exportable to Excel, or to the Clipboard.

Three different user prompts are available on Alpha and Alpha-X terminals. For
copiers supporting multiple pricing schemes, the Alpha and Alpha-X terminals
support up to four sets of four prices for four different copy types.

User codes picked up from individual Alpha and Alpha-X terminals can be accepted
into the Copy-Track database and possibly propagated to other terminals according
to a rule set in the program.

Data are first read, then collected by Copy-Track. Serial and Palm connections to
Alpha terminals can be autodetected. These data are then placed in Copy-Track‘s
Access database. This database can be placed anywhere on a network, be password
protected and addressed simultaneously by multiple instances of Copy-Track.

Copier activity is shown in clicks by copy type, and accumulated value by user code.
This activity can be valued in units or money. A collection report shows which copiers
have had data collected from them. Copier activity is used to generate preventative
maintenance reports. Data from Alpha-X terminals can be collected locally or
remotely [over the Internet], either at will or on a scheduled basis.

User codes can be activated or deactivated individually or in groups.

Copy-Track is licensed by base cost, plus number of active copiers and active user
codes needed. Palm data collection software is sold pre-loaded in a Palm Tungsten C
handheld or equivalent, which comes with a special cable.

Copy-Track is designed to run on a Windows PC with a Windows 2000, Windows XP
or Windows 2003 Server operating system.

®

is a PC based program that works in conjunction with Copicode Alpha

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

Print-Track® Print Tracking Software

Product Overview

Print-Track® is one of a suite of software products designed by Advanced
Technologies Inc. (TekVend) to control and account for copying and printing activity
on standalone copiers, networked digital copier-printers, and printers.

Print-Track is a revolutionary new printer control and accounting software product for
Windows PCs. Print-Track comes in two versions: Print-Track Plus, and Print-Track
Pro.

If you are interested in controlling copying, separately, or with printing, please
investigate our sister products Copy-Track

Both versions of Print-Track work stand-alone, on a small workgroup network, or on
a domain. Print-Track comes with three standard components: Print-Track Server,
Print-Track Client, and the common (networkable) database. A variation of Print­Track Client, Print-Track Release Station can be licensed and used in conjunction
with a vending station for anonymous vending of print jobs.

Print-Track works with Win2000, XP Pro and Win 2003 clients. Print-Track Server
need not be mounted on a Win 2000 or 2003 server: it can be mounted on any
Admin logged-on PC on the Windows network, and it controls and accounts for any
printer locally attached to any PC on that network, including IP printers. Print-Track
Client should be (but does not have to be) mounted on all network PCs that originate
monitored print jobs, but it must be mounted on all network PCs that have locally
monitored printers. In "print for pay" or other "secure release" scenarios, Print-Track
Release Station should be installed on a designated PC other than the server PC. In
limited situations, the "fast switching" feature of XP Pro can be used, but "fast
switching" is not supported on a Windows domains

While Print-Track works on a workgroup network, setting up a domain is highly
recommended for networks larger than a few PCs, because a domain's Active
Directory is well suited for logon authentication, PC netbios identification, and
uniform printing security policies. See our white paper "Controlling and Accounting
for Printing on a Windows Network".

While Print-Track is designed for Windows networks using Windows print drivers, it
will properly control and account for (against Mac and Samba logon) any print jobs
originating from Mac Panther or Tiger clients and utilizing CUPS PostScript 3 print
drivers. In such cases, the Mac clients are not bound to Active Directory but instead
print via Samba using our Mac-Track feature.

Because Print-Track uses TCP/IP communication, it will work between Windows
clients and print servers on a Novell network.

®

and Image-Track® respectively.

Main Features of Print-Track Plus

• Pauses and resumes local and remote printers

• Pauses print jobs to account for all important print job characteristics,

including document name, originating PC name, logon, destination printer,
paper size, color vs. B/W, duplex (Word docs), number of copies and pages,
job cost, job size, and date and time submitted (or completed)

• Accurately counts Word copies and automatically groups multiple copies of

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V405.

Excel spreadsheets in parent-child format

• Accurately counts Word pages for "Nup" or "Nup of Nup" printing for most
printers (hp and Lexmark emulation)

• Accounts for and parses print jobs on the local PC, not the application server,
utilizing Print -Track Client

• Allows decimal pricing per print impression to hundredths of a cent, by groups
of printers, for color and B/W

• Default printer pricing can be assigned

• Supports all Windows defined standard paper sizes

• Custom paper sizes can be defined and added

• Built-in duplex discount factor is available

• Printers can be monitored for secure release from a Print-Track Release
Station, or monitored for immediate printing after accounting and parsing

• Printers can be monitored and jobs accepted while a printer is in Service
Mode

• Secured print jobs are located by an "adjustable minimum length" release

password, and can be paid for by coin, bill, card or one or two billing codes.

• Jobs pending queue view can be limited to a single highlighted printer

• Jobs can be kept for reprinting in or out of a server session, to avoid paying

refunds for misprinted "print for pay" jobs, or any other reason

• Jobs pending, jobs completed and jobs kept queues can be column sorted by
job characteristic

• Queues can be customized to remove unwanted information

• Jobs can be automatically deleted for spool size, total number of pages, total

job cost, parsing errors, non-responding client, creation while unmonitored,
and length of time in the jobs pending queue

• Detailed reports can be sorted for up to seven variables (printer, originating
PC, logon, billing codes (two possible types), color and duplex), and
numerous custom preset reports are available

• Reports can be generated for individual billing codes, such as one client or
one matter.

• Jobs can be exported as Excel or PDF files

• Open accounting (codes can be entered on the fly) and closed accounting

(codes must be pre-entered, typed in or drop down selected) are supported

• Two types of custom definable billing codes are available

• Print-Track Server, Client and Release Station are password protected for

both their connected and unconnected states

• Print-Track Client and Print-Track Release Station can be automatically booted
at Windows startup and new logon (HKLM)

• Clients are differentiated by public (anonymous) and private (trusted) status

• Client statuses can be set globally and individually

• Trusted users at private clients can print to any type of monitored printer, but

anonymous users at public clients can print only to secure printers via print
release stations, and must pay for their print jobs

• If billing codes are not used, private clients can print with review only, or can
print to non-secure printers immediately, without any popup dialog (except
printing errors)

• Print jobs can be (but do not have to be) accepted from PCs with no client, or
a non-reporting client, for printing to non-secure printers

• Multiple instances of Print-Track can be conjoined to a single networkable and
password protectable Access or SQL Server database to produce
comprehensive reports on completed print jobs

• Printers of all types of job languages are supported through a constantly
updated parameters file (see list below)

• Statuses of local and remotely monitored printers can be checked and
updated at any time

• Accumulated value can be specified in various currencies

• Print-Track is transparent to Windows; no custom port monitors are installed

• Print jobs can be immediately released against a value limited account based

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V405.

Additional Features in Print-Track Pro

on logon and/or account code

• Accounts can be marked as budgetary (virtual value), or monetary (real
value)

• New accounts can start with a specific value

• Budgetary accounts can be replenished on a regular basis, either as an

"overwrite" or as an "add"

• Accounts can be set to run negative values

• Monetary accounts can be revalued manually or automatically (at print

release stations

• Reports additionally monitor account usage, remaining value and active status

• Accounts can expire after a certain period of non-activity, after a certain date,

or after a certain age

• Account balance can be determined at the client

• Anonymous users at public clients can print to secure and non-secure printers

against their account code value

• The privilege to use only a group of printers can be assigned to an account

• One or more accounts can be assigned a pricing discount factor

• Print jobs can be redirected to identical or equivalent printers, either

unilaterally, or as part of a load balancing scheme

Features of Print-Track Release Station

• No pulse-enable dongle is required

• Jobs are located at the release station by entering a temporary alphanumeric

release password of definable minimum length

• Private clients jobs print without monetary payment

• Public client jobs require monetary payment

• Payment can be made with coin, bill, card account value, or billing code(s)

• Vending controller can vend both copies and prints when connected to a

multifunctional copier / printer

• Vending controller with card readers can be constrained to vend prints by
card only for all print jobs, or those above a certain value, while allowing
vending of copies by coin, bill or card

• Vending controller can be set to "escrow last bill inserted" to save change

• Vending controller copy vending by card can be discounted relative to copy

vending by coin or bill

• Reprints of misprinted jobs can be performed by an Administrator at the
release station

• Orphaned jobs can be printed against monetary, account or billing code value

Licensing and Downloads

Print-Track Plus and Print-Track Pro are licensed by number of monitored printers on
an instance of Print-Track Server, for a specific time period (the lease period).
Instances of Print-Track Release Station are licensed on a per use basis. Licensing
must be completed through an email function. Please call us for pricing.

If you are interested in either version of Print-Track, you can download the
appropriate demo version from our Web site at

http://www.tekvend.com/products/Print-Track.cfm

You can also download various sample reports and an Excel spreadsheet of
supported printers (which is constantly being updated). If any of your organization's
printers are not listed, this most probably only means that the driver has not been
"officially tested" by TekVend personnel.

Windows 98 clients have not been tested with Print-Track, and are not supported.
Additionally, installation of Print-Track server automatically includes the installation
of Dot Net as required.

Installation and Technical Support

We will be glad to work with your IT personnel and your local copier / printer supplier
to assure a smooth, quick and successful installation.

Print-Track comes with free software updates and telephone support for the duration
of the lease period.

Vending Controllers

Currently, TekVend offers four vending controllers suitable for attachment to a Print­Track Release Station: the M6500S, M6506S, M7500S and M7506S controllers.
These controllers are identical to the M6500, M6506, M7500 and M7506 controllers
respectively, except they have a serial port and specialized software for connecting
to a release station PC. For a premium charge, these controllers can be connected to
a release station via a USB port, or an IP hub connection on the local area network.

Note that not only can these controllers simultaneously control copying and printing
on a single copier/printer, but they can also simultaneously control multiple printers.
Furthermore, copy control can be performed via Print-Track Release Station on a
locally attached copier/printer. Finally, print vending can be limited to cards only
(totally, or above a certain print vend price).

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V405.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V405.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V405.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V405.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V405.

Advanced Technologies, Inc.

3758 West Devon Avenue | Lincolnwood, IL 60712 | USA

Sales: [phone] | Service: [phone] | Fax: [phone]

Email: [e-mail] | Web: http://www.tekvend.com

VendGuard 1000 On-line Vending Machine Controller

Product Overview

Advanced Technologies (TekVend) is pleased to introduce the VendGuard 1000 on­line vending machine controller. This new product represents a quantum leap in the
vending machine industry.

No longer are vending machines merely money-based dispensers of candy bars, soft
drinks and the like. Instead, they are used as on-line terminal dispensers of - and
accounting mechanisms for - any motor drivable product needed by employees to do
their jobs.

With the VendGuard 1000 Controller, employees can receive any item they need at
any time: 24 hours a day, 7 days a week, 365 days a year. Plus, they are held
accountable for every item they receive. Further, the server that the vending
machine communicates with (is a terminal to) determines which items an employee
is authorized to receive.

With the VendGuard 1000 system, which includes TekVend's controller installed in a
pullout drawer and connected to from one to three vending machines:

• Employees receive items needed to do their jobs at any time, including
weekends and graveyard shift

• Employees are held responsible for every item dispensed to them (no
hoarding or shrinkage can happen)

• Employees receive only the items they are authorized to receive

• There is no labor cost associated with dispensing these items

• There is essentially no labor cost associated with receiving these items

• Liabilities related to accidents associated with needed items not being

available after hours is reduced essentially to zero

Keep in mind that each item dispensed is date-time stamped at the server as
dispensed to a particular employee. On-line vending machines can therefore be
refilled on a replacement only basis, significantly reducing inventory stock.

One obvious application for VendGuard 1000 controller equipped vending machines
is the dispensing of personal protection equipment and daily consumables in a
factory environment: gloves, sweatbands, safety glasses, batteries, Kevlar sleeves,
tapes, tape measures, knife blades, lubricants, touchup paints, locks, lockout tags,
etc.

Another obvious application is office supplies in a shared environment, specifically
inkjet cartridges and other expensive consumables. A third applications would be
hospital consumables such as bandages, gauze, syringes, suture kits, surgical
gloves, antiseptic hand lotion, etc.

The VendGuard 1000 controller installs easily in a vertical pullout drawer designed to
fit into a Fawn / USI Snackmart vending machine. The vending machine in turn is
connected on-line to a remote server hosted by Transentric Corporation. The entire
package is assembled and marketed by VendGuard of Spokane, WA. Advanced
Technologies (TekVend) manufactures the terminal electronics and hardware that
controls the vending machine.

If you are interested in this product, including new applications, please do not
hesitate to contact VendGuard directly.

Copyright © 2005 Advanced Technologies Inc. All rights reserved. V205.