Advanced Power Technology APT APT4018HVR Datasheet
APT4018HVR
400V 22A 0.180Ω
POWER MOS V
®
TO-258
Power MOS V® is a new generation of high voltage N-Channel enhancement
mode power MOSFETs. This new technology minimizes the JFET effect,
increases packing density and reduces the on-resistance. Power MOS V
also achieves faster switching speeds through optimized gate layout.
• Faster Switching • 100% Avalanche Tested
• Lower Leakage • Popular TO-258 Package
MAXIMUM RATINGS All Ratings: TC = 25°C unless otherwise specified.
Symbol
V
DSS
I
I
DM
V
V
GSM
P
TJ,T
T
I
AR
E
E
Parameter
Drain-Source Voltage
Continuous Drain Current @ T
D
Pulsed Drain Current
Gate-Source Voltage Continuous
GS
1
= 25°C
C
Gate-Source Voltage Transient
Total Power Dissipation @ TC = 25°C
D
Linear Derating Factor
Operating and Storage Junction Temperature Range
STG
Lead Temperature: 0.063" from Case for 10 Sec.
L
1
Avalanche Current
Repetitive Avalanche Energy
AR
Single Pulse Avalanche Energy
AS
(Repetitive and Non-Repetitive)
1
4
®
D
G
S
APT4018HVR
400
UNIT
Volts
22
88
Amps
±30
±40
Volts
200
1.6
-55 to 150
Watts
W/°C
°C
300
22
Amps
30
1210
mJ
STATIC ELECTRICAL CHARACTERISTICS
Symbol
BV
I
D(on)
R
DS(on)
I
DSS
I
GSS
V
GS(th)
USA
405 S.W. Columbia Street Bend, Oregon 97702-1035 Phone: (541) 382-8028 FAX: (541) 388-0364
EUROPE
Avenue J.F. Kennedy Bât B4 Parc Cadéra Nord F-33700 Merignac - France Phone: (33)5 579215 15 FAX: (33) 556 47 9761
Characteristic / Test Conditions
Drain-Source Breakdown Voltage (V
DSS
On State Drain Current
2
(V
DS
Drain-Source On-State Resistance
Zero Gate Voltage Drain Current (VDS = V
Zero Gate Voltage Drain Current (V
Gate-Source Leakage Current (VGS = ±30V, V
= 0V, ID = 250µA)
GS
> I
x R
D(on)
2
(VGS = 10V, 0.5 I
= 0.8 V
DS
Max, VGS = 10V)
DS(on)
D[Cont.]
, VGS = 0V)
DSS
, VGS = 0V, TC = 125°C)
DSS
= 0V)
DS
)
Gate Threshold Voltage (VDS = VGS, ID = 1.0mA)
CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed.
APT Website - http://www.advancedpower.com
MIN TYP MAX
400
22
24
0.180
25
250
±100
UNIT
Volts
Amps
Ohms
µA
nA
Volts
050-5821 Rev B
DYNAMIC CHARACTERISTICS
Note:
Duty Factor D =
t
1
/
t
2
Peak TJ = PDM x Z
θJC
+ T
C
t
1
t
2
P
DM
APT4018HVR
Symbol
C
iss
C
oss
C
rss
Q
g
Q
gs
Q
gd
t
d(on)
t
r
t
d(off)
t
f
Characteristic
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
Total Gate Charge
3
Gate-Source Charge
Gate-Drain ("Miller") Charge
Turn-on Delay Time
Rise Time
Turn-off Delay Time
Fall Time
Test Conditions
V
VDS = 25V
f = 1 MHz
V
GS
VDD = 0.5 V
ID = I
D[Cont.]
VGS = 15V
VDD = 0.5 V
ID = I
D[Cont.]
RG = 1.6Ω
SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS
Symbol
I
I
SM
V
t
Q
Characteristic / Test Conditions
Continuous Source Current (Body Diode)
S
1
Pulsed Source Current
Diode Forward Voltage 2 (VGS = 0V, IS = -I
SD
Reverse Recovery Time (IS = -I
rr
Reverse Recovery Charge (I
rr
(Body Diode)
S
= -I
, dlS/dt = 100A/µs)
D[Cont.]
, dlS/dt = 100A/µs)
D[Cont.]
D[Cont.]
)
= 0V
GS
= 10V
DSS
@ 25°C
DSS
@ 25°C
MIN TYP MAX
3350 4020
510 715
198 300
135 200
24 36
60 90
11 22
10 20
48 75
612
MIN TYP MAX
22
88
1.3
380
6.4
UNIT
pF
nC
ns
UNIT
Amps
Volts
ns
µC
050-5821 Rev B
THERMAL CHARACTERISTICS
Symbol
R
θJC
R
1
Repetitive Rating: Pulse width limited by maximum junction
temperature.
2
Pulse Test: Pulse width < 380 µS, Duty Cycle < 2%
APT Reserves the right to change, without notice, the specifications and information contained herein.
Characteristic
Junction to Case
Junction to Ambient
θJA
0.7
0.5
0.1
0.05
0.01
0.005
, THERMAL IMPEDANCE (°C/W)
JC
θ
Z
0.001
-5
10
3
See MIL-STD-750 Method 3471
4
Starting T
D=0.5
0.2
0.1
0.05
0.02
0.01
SINGLE PULSE
-4
10
FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION
-3
10
RECTANGULAR PULSE DURATION (SECONDS)
-2
10
+25°C, L = 5.00mH, R
j
=
-1
10
MIN TYP MAX
0.62
40
25Ω, Peak IL = 22A
G
=
1.0 10
UNIT
°C/W
Loading...