ADVANCED POWER TECHNOLOGY APT10M11JVR Service Manual

查询APT10M11JVR供应商

APT10M11JVR

100V 144A 0.011Ω

POWER MOS V

®

Power MOS V® is a new generation of high voltage N-Channel enhancement
mode power MOSFETs. This new technology minimizes the JFET effect,
increases packing density and reduces the on-resistance. Power MOS V

also achieves faster switching speeds through optimized gate layout.

• Faster Switching • 100% Avalanche Tested

• Lower Leakage • Popular SOT-227 Package

S

G

®

ISOTOP

G

D

®

S

SOT-227

"UL Recognized"

D

S

MAXIMUM RATINGS All Ratings: TC = 25°C unless otherwise specified.

Symbol

V

DSS

I

D

I

DM

V

GS

V

GSM

P

D

TJ,T

STG

T

L

I

AR

E

AR

E

AS

Parameter

Drain-Source Voltage
Continuous Drain Current @ T
Pulsed Drain Current
Gate-Source Voltage Continuous
Gate-Source Voltage Transient
Total Power Dissipation @ T
Linear Derating Factor
Operating and Storage Junction Temperature Range
Lead Temperature: 0.063" from Case for 10 Sec.
Avalanche Current
Repetitive Avalanche Energy
Single Pulse Avalanche Energy

1

1

(Repetitive and Non-Repetitive)

= 25°C

C

= 25°C

C

1

4

APT10M11JVR

100
144
576

±30
±40

450

3.6

-55 to 150
300
144

50

2500

UNIT

Volts

Amps

Volts

Watts

W/°C

°C

Amps

mJ

STATIC ELECTRICAL CHARACTERISTICS

Symbol

BV

I

D(on)

R

DS(on)

I

DSS

I

GSS

V

GS(th)

USA

405 S.W. Columbia Street Bend, Oregon 97702-1035 Phone: [phone] FAX: [phone]

EUROPE

Avenue J.F. Kennedy Bât B4 Parc Cadéra Nord F-33700 Merignac - France Phone: [phone] FAX: [phone]

Characteristic / Test Conditions

Drain-Source Breakdown Voltage (V

DSS

On State Drain Current
Drain-Source On-State Resistance

Zero Gate Voltage Drain Current (VDS = V
Zero Gate Voltage Drain Current (V
Gate-Source Leakage Current (VGS = ±30V, V
Gate Threshold Voltage (VDS = VGS, ID = 2.5mA)

CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed.

2

(V

DS

APT Website - http://www.advancedpower.com

= 0V, ID = 250µA)

GS

> I

x R

D(on)

2

(VGS = 10V, 0.5 I

= 0.8 V

DS

Max, VGS = 10V)

DS(on)

D[Cont.]

, VGS = 0V)

DSS

, VGS = 0V, TC = 125°C)

DSS

= 0V)

DS

)

MIN TYP MAX

100
144

24

0.011
250

1000
±100

UNIT

Volts

Amps
Ohms

µA

nA

Volts

050-5550 Rev C

DYNAMIC CHARACTERISTICS

Note:

Duty Factor D =

t

1

/

t

2

Peak TJ = PDM x Z

θJC

+ T

C

t

1

t

2

P

DM

APT10M11JVR

Symbol

C

iss

C

oss

C

rss

Q

g

Q

gs

Q

gd

t

d(on)

t

r

t

d(off)

t

f

Characteristic

Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
Total Gate Charge

3

Gate-Source Charge
Gate-Drain ("Miller") Charge
Turn-on Delay Time
Rise Time
Turn-off Delay Time
Fall Time

Test Conditions

V

VDS = 25V

f = 1 MHz

V

GS

VDD = 0.5 V

ID = 50A @ 25°C

VGS = 15V

VDD = 0.5 V

ID = I

D[Cont.]

RG = 0.6Ω

SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS

Symbol

I

I

SM

V

t

Q

Characteristic / Test Conditions

Continuous Source Current (Body Diode)

S

1

Pulsed Source Current
Diode Forward Voltage 2 (VGS = 0V, IS = -I

SD

Reverse Recovery Time (IS = -I

rr

Reverse Recovery Charge (I

rr

(Body Diode)

S

= -I

, dlS/dt = 100A/µs)

D[Cont.]

, dlS/dt = 100A/µs)

D[Cont.]

D[Cont.]

)

= 0V

GS

= 10V

DSS

DSS

@ 25°C

MIN TYP MAX

8600 10300
3200 4480
1180 1770

300 450

95 145

110 165

16 32
48 96
51 75

918

MIN TYP MAX

144
576

1.3

250

2.5

UNIT

pF

nC

ns

UNIT

Amps

Volts

ns

µC

050-5550 Rev C

THERMAL/PACKAGE CHARACTERISTICS

Symbol

R
R

V

Isolation

Torque

1

Repetitive Rating: Pulse width limited by maximum junction
temperature.

2

Pulse Test: Pulse width < 380 µS, Duty Cycle < 2%

APT Reserves the right to change, without notice, the specifications and information contained herein.

Characteristic

Junction to Case

θJC

Junction to Ambient

θJA

RMS Voltage (50-60 Hz Sinusoidal Waveform From Terminals to Mounting Base for 1 Min.)
Maximum Torque for Device Mounting Screws and Electrical Terminations.

3

See MIL-STD-750 Method 3471

4

Starting T

0.3
D=0.5

, THERMAL IMPEDANCE (°C/W)

JC

Z

θ

0.1

0.05

0.01

0.005

0.001

-5

10

0.2

0.1

0.05

0.02

0.01

FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION

SINGLE PULSE

-4

10

-3

10

RECTANGULAR PULSE DURATION (SECONDS)

-2

10

+25°C, L = 241µH, R

j

=

-1

10

MIN TYP MAX

0.28
40

2500

13

25Ω, Peak IL = 144A

G

=

1.0 10

UNIT

°C/W

Volts

lb•in

1

2