ADVANCED POWER TECHNOLOGY APT10086SVR Service Manual
查询APT10086SVR供应商
APT10086SVR
1000V 13A 0.860Ω
POWER MOS V
®
Power MOS V® is a new generation of high voltage N-Channel enhancement
mode power MOSFETs. This new technology minimizes the JFET effect,
increases packing density and reduces the on-resistance. Power MOS V
®
also achieves faster switching speeds through optimized gate layout.
• Faster Switching • 100% Avalanche Tested
3
• Lower Leakage • Surface Mount D
MAXIMUM RATINGS All Ratings: TC = 25°C unless otherwise specified.
Symbol
V
DSS
I
I
DM
V
V
GSM
P
TJ,T
T
I
AR
E
E
Parameter
Drain-Source Voltage
Continuous Drain Current @ T
D
Pulsed Drain Current
Gate-Source Voltage Continuous
GS
1
= 25°C
C
Gate-Source Voltage Transient
Total Power Dissipation @ TC = 25°C
D
Linear Derating Factor
Operating and Storage Junction Temperature Range
STG
Lead Temperature: 0.063" from Case for 10 Sec.
L
1
Avalanche Current
Repetitive Avalanche Energy
AR
Single Pulse Avalanche Energy
AS
(Repetitive and Non-Repetitive)
1
4
PAK Package
APT10086SVR
D3PAK
G
1000
13
52
±30
±40
370
2.96
-55 to 150
300
13
30
1300
D
S
UNIT
Volts
Amps
Volts
Watts
W/°C
°C
Amps
mJ
STATIC ELECTRICAL CHARACTERISTICS
Symbol
BV
I
D(on)
R
DS(on)
I
DSS
I
GSS
V
GS(th)
USA
405 S.W. Columbia Street Bend, Oregon 97702-1035 Phone: (541) 382-8028 FAX: (541) 388-0364
EUROPE
Avenue J.F. Kennedy Bât B4 Parc Cadéra Nord F-33700 Merignac - France Phone: (33)5 579215 15 FAX: (33) 556 47 9761
Characteristic / Test Conditions
Drain-Source Breakdown Voltage (V
DSS
On State Drain Current
2
(V
DS
Drain-Source On-State Resistance
Zero Gate Voltage Drain Current (VDS = V
Zero Gate Voltage Drain Current (V
Gate-Source Leakage Current (VGS = ±30V, V
= 0V, ID = 250µA)
GS
> I
x R
D(on)
2
(VGS = 10V, 0.5 I
= 0.8 V
DS
Max, VGS = 10V)
DS(on)
D[Cont.]
, VGS = 0V)
DSS
, VGS = 0V, TC = 125°C)
DSS
= 0V)
DS
)
Gate Threshold Voltage (VDS = VGS, ID = 1.0mA)
CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed.
APT Website - http://www.advancedpower.com
MIN TYP MAX
1000
13
24
0.86
25
250
±100
UNIT
Volts
Amps
Ohms
µA
nA
Volts
050-5570 Rev B
DYNAMIC CHARACTERISTICS
Note:
Duty Factor D =
t
1
/
t
2
Peak TJ = PDM x Z
θJC
+ T
C
t
1
t
2
P
DM
APT10086SVR
Symbol
C
iss
C
oss
C
rss
Q
g
Q
gs
Q
gd
t
d(on)
t
r
t
d(off)
t
f
Characteristic
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
Total Gate Charge
3
Gate-Source Charge
Gate-Drain ("Miller") Charge
Turn-on Delay Time
Rise Time
Turn-off Delay Time
Fall Time
Test Conditions
V
VDS = 25V
f = 1 MHz
V
GS
VDD = 0.5 V
ID = I
D[Cont.]
VGS = 15V
VDD = 0.5 V
ID = I
D[Cont.]
RG = 1.6Ω
SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS
Symbol
I
I
SM
V
t
Q
Characteristic / Test Conditions
Continuous Source Current (Body Diode)
S
1
Pulsed Source Current
Diode Forward Voltage 2 (VGS = 0V, IS = -I
SD
Reverse Recovery Time (IS = -I
rr
Reverse Recovery Charge (I
rr
(Body Diode)
S
= -I
, dlS/dt = 100A/µs)
D[Cont.]
, dlS/dt = 100A/µs)
D[Cont.]
D[Cont.]
)
= 0V
GS
= 10V
DSS
@ 25°C
DSS
@ 25°C
MIN TYP MAX
3700 4440
350 490
180 270
185 275
16 24
90 135
12 24
10 20
43 65
10 20
MIN TYP MAX
13
52
1.3
800
11
UNIT
pF
nC
ns
UNIT
Amps
Volts
ns
µC
050-5570 Rev B
THERMAL CHARACTERISTICS
Symbol
R
θJC
R
1
Repetitive Rating: Pulse width limited by maximum junction
temperature.
2
Pulse Test: Pulse width < 380 µS, Duty Cycle < 2%
APT Reserves the right to change, without notice, the specifications and information contained herein.
Characteristic
Junction to Case
Junction to Ambient
θJA
0.4
0.1
0.05
0.01
0.005
, THERMAL IMPEDANCE (°C/W)
JC
θ
Z
0.001
-5
10
3
See MIL-STD-750 Method 3471
4
Starting T
D=0.5
0.2
0.1
0.05
0.02
0.01
SINGLE PULSE
-4
10
FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION
-3
10
RECTANGULAR PULSE DURATION (SECONDS)
-2
10
+25°C, L = 15.38mH, R
j
=
-1
10
MIN TYP MAX
0.34
40
25Ω, Peak IL = 13A
G
=
1.0 10
UNIT
°C/W
Loading...