ADVANCED POWER TECHNOLOGY APT1001R6BN Service Manual
查询APT1001R6BN供应商
D
G
S
TO-247
APT1001R6BN 1000V 8.0A 1.60Ω
APT1002R4BN 1000V 6.5A 2.40Ω
POWER MOS IV
N-CHANNEL ENHANCEMENT MODE HIGH VOLTAGE POWER MOSF ETS
MAXIMUM RATINGS All Ratings: T
Symbol
V
I
V
P
TJ,T
DSS
I
D
DM
GS
D
STG
T
L
Parameter
Drain-Source Voltage
Continuous Drain Current @ T
Pulsed Drain Current
Gate-Source Voltage
Total Power Dissipation @ T
Linear Derating Factor
Operating and Storage Junction Temperature Range
Lead Temperature: 0.063" from Case for 10 Sec.
®
= 25°C unless otherwise specified.
C
APT APT
1001R6BN 1002R4BN
1000 1000
= 25°C
C
1
8 6.5
32 26
±30
= 25°C
C
240
1.96
-55 to 150
300
UNIT
Volts
Amps
Volts
Watts
W/°C
°C
STATIC ELECTRICAL CHARACTERISTICS
Symbol
BV
ID(ON)
R
DS
I
DSS
I
GSS
VGS(TH)
Characteristic / Test Conditions / Part Number
Drain-Source Breakdown Voltage
DSS
(V
= 0V, ID = 250 µA)
GS
On State Drain Current
(V
> ID(ON) x RDS(ON) Max, VGS = 10V)
DS
Drain-Source On-State Resistance
(ON)
(VGS = 10V, 0.5 ID [Cont.])
2
Zero Gate Voltage Drain Current (V
Zero Gate Voltage Drain Current (V
Gate-Source Leakage Current (V
Gate Threshold Voltage (V
= VGS, ID = 1.0mA)
DS
2
= V
DS
= 0.8 V
DS
= ±30V, V
GS
, VGS = 0V)
DSS
, VGS = 0V, TC = 125°C)
DSS
= 0V)
DS
MIN TYP MAX
APT1001R6BN
1000
APT1002R4BN 1000
APT1002RBN 8
APT1002R4BN 6.5
APT1001R6BN 1.60
APT1002R4BN 2.40
250
1000
±100
24
UNIT
Volts
Amps
Ohms
µA
nA
Volts
THERMAL CHARACTERISTICS
Symbol
R
R
USA
405 S.W. Columbia Street Bend, Oregon 97702-1035 Phone: (541) 382-8028 FAX: (541) 388-0364
EUROPE
Avenue J.F. Kennedy Bât B4 Parc Cadéra Nord F-33700 Merignac - France Phone: (33) 5 57 92 15 15 FAX: (33) 5 56 47 97 61
Characteristic
Junction to Case
θJC
Junction to Ambient
θJA
CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed.
MIN TYP MAX
UNIT
0.51
°C/W
40
050-0109 Rev B
DYNAMIC CHARACTERISTICS
APT1001R6BN
Symbol
C
iss
C
oss
C
rss
Q
g
Q
gs
Q
gd
td(on)
t
r
td(off)
t
f
Characteristic
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
Total Gate Charge
3
Gate-Source Charge
Gate-Drain ("Miller") Charge
Turn-on Delay Time
Rise Time
Turn-off Delay Time
Fall Time
Test Conditions
V
VDS = 25V
f = 1 MHz
V
GS
VDD = 0.5 V
ID = ID [Cont.] @ 25°C
V
GS
VDD = 0.5 V
ID = ID [Cont.] @ 25°C
RG = 1.8Ω
SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS
I
SM
t
Characteristic / Test Conditions / Part Number
Continuous Source Current
S
(Body Diode)
Pulsed Source Current
1
(Body Diode)
2
Diode Forward Voltage
SD
Reverse Recovery Time (I
rr
Reverse Recovery Charge (I
rr
(VGS = 0V, IS = -ID [Cont.])
= -ID [Cont.], dlS/dt = 100A/µs)
S
= -ID [Cont.], dlS/dt = 100A/µs)
S
Symbol
I
V
Q
MIN TYP MAX
GS
= 0V
1530 1800
230 325
80 120
= 10V
DSS
66 105
6.5 10
36 54
= 15V
DSS
14 28
13 26
55 82
19 37
MIN TYP MAX
APT1001R6BN
APT1002R4BN 6.5
APT1001R6BN 32
APT1002R4BN 26
450 910
2.5 5
8
1.3
UNIT
pF
nC
ns
UNIT
Amps
Volts
ns
µC
SAFE OPERATING AREA CHARACTERISTICS
Symbol
SOA1
SOA2
I
1
Repetitive Rating: Pulse width limited by maximum junction temperature. See Transient Thermal Impedance Curve. (Fig.1)
2
Pulse Test: Pulse width < 380 µS, Duty Cycle < 2%
3
See MIL-STD-750 Method 3471
APT Reserves the right to change, without notice, the specifications and information contained herein.
050-0109 Rev B
Characteristic
Safe Operating Area
Safe Operating Area
Inductive Current Clamped
LM
1.0
0.5
0.1
0.05
0.01
0.005
0.001
D=0.5
0.2
0.1
0.05
0.02
0.01
-5
10
FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION
SINGLE PULSE
-4
10
Test Conditions / Part Number
V
= 0.4 V
DS
= ID [Cont.], VDS = PD / ID [Cont.], t = 1 Sec.
I
DS
, IDS = PD / 0.4 V
DSS
, t = 1 Sec.
DSS
APT1001R6BN 32
APT1002R4BN 26
-3
10
RECTANGULAR PULSE DURATION (SECONDS)
-2
10
10
MIN TYP MAX
240
240
Note:
DM
P
Duty Factor D =
Peak TJ = PDM x Z
-1
1.0 10
UNIT
Watts
Amps
t
1
t
2
t
1
/
t
2
+ T
θJC
C
Loading...