Advanced Network Devices AND-BTN-KIT-1 Data Sheet

AND-BTN-KIT-1 & AND-BTN-KIT-1D

Button Kit Overview

The peripheral interface adapter (AND-PIA-2 & AND-PIA-2D) interfaces with the
call button via the general purpose input signal on the “poke-home” connector. The
AND Call Button Kit is used for initiating 2-way communication between devices
or devices and phones. This kit can be used with most AND devices to trigger an
external alert.

AND-BTN-KIT-1

Vandal Proof Button Kit

Features

Two Way Communication:

• Activate via push button

• Allows for full duplex hands free
communication

Multiple Extensions:

• Program up to two extensions
or phone numbers. The primary
extension is dialed upon pushing
the button.

• The secondary extension is dialed
when the button is pushed and
held. (I.e. Push once to talk to the
office; push and hold to connect to

campus or district security.)

Dial-Out:

• When connected to an Advanced
Network Device on your PBX
(connected via SIP) the Call
Button Kit can be programmed to
dial both internal extensions and

external phone numbers

• Faceplate diameters are for installation
with any standard back box

• Faceplate is 16 gauge brushed stainless
steel

• Button diameter is .6” (15mm)

• Polished Stainless Steel

• Circuit SPST

• Switch Function Momentary ON

• Rating 2A @ 48VDC

• Electrical Life: 200,000 cycles

• Operating Temperature: -20 C to 55 C

• Ingress Protection: IP65

• Installation Depth: 1” (25.4mm)

• Screw Type Terminals

AND-BTN-KIT-1D

AND-PIA-2 & AND-PIA-2D SpecicationsCall Button Specications

• Use 18-22 AWG stranded or solid core wire
pair to connect button to peripheral interface
board

• Vandal resistant screws included to increase
security

• The peripheral interface adapter
(AND-PIA-2 & AND-PIA-2D) makes
any combination of the following signals
available via two “poke-home” connectors
on the board:

• Line Level Audio In

• Line Level Audio Out

• 2 General Purpose Inputs

• General Purpose Output Relay (N.O. or

N.C; dry or 12V or 15VDC, 1A max)

Device Requirements:

• Compatible with AND devices of
MAC address 20:46:F9:03:00:00
or higher.

• Use with PoE or PoE+ power
source

Notes:

• IPSIGNL-RWB and IPCDS-RWB

require the modied peripheral

interface board
(Part # AND-PIA-2D).

• IPSCM model does not support
this kit.

• ZONEC2 does not require the
AND-PIA-2 or AND-PIA-2D
adapter.

Advanced Network Devices • 3820 Ventura Dr. Arlington Hts. IL 60004 • Phone: [phone] • Fax: [phone]

Website: www.anetd.com • E-Mail: [e-mail]

R1.3

AND-BTN-KIT-1 & AND-BTN-KIT-1D

Diagram 1

Call Button Dimensions

Call Button Capabilities

Functions:

• Intercom

• Dial out pre-programmed number

• Alarm trigger

• Trigger sound masking

• Trigger pre-programmed text

• Page or all-call

• Trigger privacy mode

Advanced Network Devices • 3820 Ventura Dr. Arlington Hts. IL 60004 • Phone: [phone] • Fax: [phone]

Website: www.anetd.com • E-Mail: [e-mail]

Dual Commands:

• Supports up to two commands

• Commands programmable as:

• 1: Button push and release

• 2: Button push and hold

R1.3