Advanced Control Technologies ZRW100I Specs Instructions
HomePro
ZRW100
RF Home Automation
Radio Frequency Controlled, 120 VAC,
Wall Mounted Switch
Shown with user supplied
DecoraTM trim plate
ZRW100 WALL MOUNTED SWITCH
The ZRW100 Wall Mounted Switch is a component of the HomePro lighting control system. Wire the Wall Mounted
Switch in place of the standard wall switch according to the diagram above and program from the Wireless Controller
to operate loads. Inclusion of this Wall Mounted Switch on the ZTH100 Wireless Controller menu allows remote ON/
OFF control of lamps connected.
This Wall Mounted Switch is designed to work with other HomePro lamp and appliance controls. Z-Wave nodes of
other types can be added to the system and will also act as repeaters if they support this function of repeating the signal
received to other modules in the system.
As part of a HomePro network, the ZRW100 will also act as a wireless repeater to insure that commands intended
for another device in the network are received. This is useful when the device would otherwise be out of the radio
range of the wireless controller.
There are no field repairable assemblies on this unit. It is covered by a one year limited warranty. If service is needed,
the unit must be returned where purchased.
CAUTION! Read and understand these instructions before installing. This device is entended for installation in
accordance with the National Electric code and local regulations in the United States, or the Canadian Electrical Code
and local regulations in Canada. It is recommended that a qualified electrician perform this installation.
Make sure the load controlled the switch does not exceed 1800 watts. For indoor use only. Retain instructions for
future use.
INSTALLATION
Wire this Wall Mounted Switch in place of a current wall switch according to the diagram above. See the ZTH100
Wireless Controller operating instructions to add this module under the command of the Wireless Controller.
Wall Mounted Switch Configuration
The Wall Mounted Switch locally controls the load ON and OFF. A push on the top or bottom of the paddle switch
is used to configure the module to operate from the wireless controller. With the Wireless Controller, the Wall
Mounted Switch can be switched ON and OFF remotely, and can be included in groups of lights that operate at
the same time (a group can also be a single module), and in scenes that set a lighting mood.
Switch power ON and OFF locally
When the top of the paddle is pressed, the power will turn on. When the bottom of the paddle is pressed, the power
will turn off.
HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
0618-01
1
ZRW100 Instructions
110503
Child Protection
The Wall Mounted Switch can be set in a child protect mode by the Wireless Controller. When this mode is active,
a user will have to press the Wall Mounted Switch 3 times rapidly to activate the attached load. The module
operates normally when controlled by the Wireless Controller..
Other functions
The paddle on the Wall Mounted Switch also plays a role as a reset in addition to adding module to groups and
scenes. This is described in more detail in the Wireless Controller instructions.
Over-current protection
The Wall Mounted Switch is protected by an internal fuse. This internal fuse is factory serviceable only. Check
your home circuit breakers before concluding that the product must be returned to manufacturer for repair at a
nominal charge.
WARRANTY
For warranty and general product information visit our web site at www.act-solutions.com
ABOUT ZRW100’S CERTIFICATION
The ZRW100 has been thoroughly tested by the ETL SEMCO
division of Intertek, a nationally recognized testing laboratory. This
product was found to be in compliance with safety standards
ANSI/UL STD 244A and CAN/CSA C22.2 No. 177.
In addition to compliance with product safety standards, the ZRW100
is also certified to comply with applicable FCC and IC rules and
regulations governing RF and EMI emissions.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) This device must accept any interference received, including interference that may
cause undesired operation.
FCC NOTICE
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Increase the separation between the equipment and receiver.
- Consult the dealer or an experienced radio/TV technician for help.
IC NOTICE
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Power 120 VAC, 60 Hz
Signal (Frequency) 908.42 MHz
Maximum Load Resistive: 15 amps (1800 watts) maximum, 120 VAC
Motor: 1/2 H.P. maximum, 120 VAC
Incandescent: 600W maximum, 120 VAC
Range Up to 100 feet line of sight between the Wireless Controller and /or the
ZRW100 Instructions
110503
closest HomePro Reciever Module
0618-01
2
by ADVANCED CONTROL TECHNOLOGIES, INC.
HomePro
Loading...