Advance Adapters 716638 User Manual

ADVANCE ADAPTERS INC. P/N: 716638

P.O. Box 247, 4320 Aerotech Center Way
Paso Robles, CA 93447 PAGE 1 OF 2
Telephone: [phone] Fax: [phone] Page Rev. Date: 10-28-96

JEEP CLUTCH CONTROL MOUNTING BRKT.

1973-87 USING CHEVY V8 ENGINES

KIT CONSISTS OF:
No. Qty Part No. Description

1. 1 716030 SPEC. BALL PIVOT 7/16"-14 THREADS

2. 2 716031 NEW JEEP REPLACEMENT BUSHINGS

3. 2 716037 STEEL STRAPS

4. 1 716139 CLUTCH FORK WEDGE

5. 1 716638-BLK MOUNTING PLATE

6. 4 723704 3/8" LOCK WASHER

7. 2 723719 3/8"-24 JAM NUT

8. 2 723724 3/8"-16 x 1-3/4" H.H.C.S.

9. 2 723739 3/8"-16 x 1" H.H.C.S.

10. 1 725002 1/2" LOCK WASHER

11. 1 725030 1/2"-13 x 2-1/2" H.H.C.S.

SPECIAL NOTES:

1. All original linkage and connections must remain as illustrated.

2. New nylon ball pivot bushings have been furnished since we have experienced severe wear on the original clutch
tube.

3. Grease assembly before operation.

4. Adjust linkage for proper release bearing clearance. Refer to your Jeep service manual for the adjustment procedure.

5. Both pedal and release arm springs must be re-used.

6. These kits are for all Jeep CJ models, Cherokee, and Jeep truck vehicles.

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void
any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend that
you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a service
manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive dealerships
and parts stores.

ADVANCE ADAPTERS INC. P/N: 716638

P.O. Box 247, 4320 Aerotech Center Way
Paso Robles, CA 93447 PAGE 2 OF 2
Telephone: [phone] Fax: [phone] Page Rev. Date: 11-15-94

JEEP CLUTCH CONTROL MOUNTING BRKT.

1973-87 USING CHEVY V8 ENGINES

The new mounting plate bolts to the engine block using one 1/2"-13 X 2-1/2" LONG bolt
and lock washer. Multiple tapped holes permit various centerline locations on vehicles
1973-87. The position varies with the transmission being used or model of original
transmission being replace.

Standard distance on most bellhousings.

ORIGINAL GREASE SEAL BOOT
2 PLACES

Original parts

Pedal return
spring

Original spring
clips - 2 places

Some variations will occur on different
bellhousings requiring shimming with 3/8"
standard flat washers.

3/8"-16 X 1" H.H.C.S. for plate

Bolt goes through holes
into bellhousing

3/8"-16 X 1-3/4" H.H.B. for
engine block

Original pedal

Original clutch tube. It must be trapped between the
pivot point so that the original spring clips can be used.

ORIGINAL BRACKET: Depending on exact engine
location, this bracket may need to be spaced away
from the firewall up to 1-1/2" and can be moved inward
towards new engine for proper clutch tube spacing
over ball pivots. This varies depending on engine
position. No spacing should be required with engines
offset 1/2" towards driver's side.

Zerk Nut

(2) 3/8"-24 Jam nut

Original
linkage

Original clutch lever
return spring

Clutch release lever
P/N 716176 - Other
levers will not work.

Both springs must be re-used on a
new V8 clutch installation.

New clutch fork wedge
P/N 716139

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void
any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend that
you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a service
manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive dealerships
and parts stores.