Advance Adapters 715630 User Manual

ADV ANCE ADAPTERS INC. P/N: 715630

P.O. Box 247, 4320 Aerotech Center Way
Paso Robles, CA 93447 PAGE 1 OF 2
Telephone: [phone] Fax: [phone] Page Rev. Date: 07-18-02

SHIFTER LINKAGE ROD & LEVER KIT

FOR EARL Y BRONCO T&C TRANSMISSION

KIT CONSISTS OF:
No. Qty Part No. Description

1. 3 715649 BUTTONS

2. 6 715650 NYLON BUSHINGS

3. 3 715651 CLIPS

4. 1 715653 LEVER

5. 1 715661 ROD

6. 1 715662 ROD

7. 1 715663 ROD

8. 1 715670 LEVER

9. 1 715678 LEVER

10. 3 303115 E-CLIP RETAINER V

PART NO.
71564

P.N. 715670
(REVERSE)

PART NO. 715663

PART NO. 715661

PART NO. 715662

P/N 715678
(1st & 2nd Gear)

PART NO.
715644

BAGGED HARDWARE

PART NO. 715646

PART NO.
715647

TYPICAL HURST SHIFTER

PART NO. 715600

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components
will void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly
recommend that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components.
We recommend that a service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are
normally available at automotive dealerships and parts stores.

ADV ANCE ADAPTERS INC. P/N: 715630

P.O. Box 247, 4320 Aerotech Center Way
Paso Robles, CA 93447 PAGE 2 OF 2
Telephone: [phone] Fax: [phone] Page Rev. Date: 07-18-02

SHIFTER LINKAGE ROD & LEVER KIT

FOR EARL Y BRONCO T&C TRANSMISSION

INSTALLATION INSTRUCTIONS:

1. Align levers with shifter frame and insert neutral *alignment rod through notches in frame and holes in levers.

(*Use small bolt or pin to align).

2. Rotate transmission arms backward and forward. The neutral position for each arm can be felt at the mid-position
of full travel. Reverse arm must be moved to the end of its travel toward the front (disengage position).

3. Adjust position of button on each rod to permit easy slip-in fit of button into nylon bushings in proper lever.

Transmission arms must remain in neutral position while aligning is being performed. Fasten buttons in levers with

spring clips.

4. Remove neutral alignment rod. Test shifter. Stick should move freely from side to side at neutral (between 1-2
& 3-4 shifting paths). An increased pull towards the operator should engage the reverse lever.

5. Adjust shifter stop bolts. Back bolts out of shifter frame into 3rd gear and hold. Screw in 3rd gear stop bolt until
contact is felt. Back out bolt one turn and tighten lock nut. Pull stick firmly back into 4th gear, screw in 4th gear
stop bolt until contact is made, then back out stop bolt one turn and tighten lock nut.

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void
any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend that
you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a service
manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive dealerships
and parts stores.