Advance Adapters 713089 User Manual

ADVANCE ADAPTERS INC. P/N: 713089

P.O. Box 247, 4320 Aerotech Center Way New Item: (2/99)
Paso Robles, CA 93447 PAGE 1 OF 3
Telephone: [phone] Fax: [phone] Page Rev. Date: 03/7/09

CHEVY V8 BOLT-IN MOUNT

1976-86 CJ's also V6's WITH AUTO TRANS.

KIT CONSISTS OF:
No. Qty Part No. Description

1. 2 4980 STOCK GM MOUNTS

2. 1 713089-L LEFT MOUNT

3. 1 713089-R RIGHT MOUNT

4. 1 713089S RUBBER BUMP STOP

5. 10 723701 3/8"-16 NUT PLATED

6. 10 723704 LOCK WASHER, 3/8" PLATED

7. 8 723733 H.H.C.S. 3/8"-16 X 2-1/2" PLT (GR 5)

8. 2 723738 H.H.C.S. 3/8"-16 X 2-3/4"

9. 2 724301 NYLON LOCK NUT, 7/16"-14 PLT.

10. 2 724302 FLAT WASHER 7/16" PLT.

11. 2 724311 H.H.C.S. 7/16"-14 X 3-1/2" (GR 5)

12. 1 JP001 JEEP INSTRUCTION MANUAL

SPECIAL NOTE:

If using this mount with our clutch
bracket P/N 716638, the clutch
linkage bracket will require some
modifications.

The GM rubber mount supplied in this kit may
be a loose fit over the tubing on our mount. If so
the bolt installed and tightened through the mount
will squeeze the two tabs on the GM mount
closer together for a proper fit to the Advance
Adapters mount. These GM mounts supplied
sometimes vary in widths from the manufacture.

INSTALLATION PROCEDURES:

This mount kit is designed as a bolt in application. Some cutting is required.

1. Unbolt and remove the stock frame mounts from the vehicle. The passenger side
stock bump stop must be cut off and the frame rail must be ground flat.

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void
any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend that
you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a service
manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive dealerships
and parts stores.

ADVANCE ADAPTERS INC. P/N: 713089

P.O. Box 247, 4320 Aerotech Center Way New Item: (2/99)
Paso Robles, CA 93447 PAGE 2 OF 3
Telephone: [phone] Fax: [phone] Page Rev. Date: 12-12-00

CHEVY V8 BOLT-IN MOUNT

1976-86 CJ's also V6's WITH AUTO TRANS.

2. Frame rail ground flat.

4. The new mounts use the hole of the stock frame mounts,
plus the front shock tower bolt hole. A new bump stop has
been added as part of the mount.

3. Driverside frame with stock mount removed.

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void
any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend that
you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a service
manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive dealerships
and parts stores.