Advance Adapters 713027-EK User Manual

ADVANCE ADAPTERS INC. P/N: 713027-EK

P.O. Box 247, 4320 Aerotech Center Way
Paso Robles, CA 93447 PAGE 1 OF 2
Telephone: [phone] Fax: [phone] Page Rev . Date: 01-31-14

TOYOTA LAND CRUISER 4 SPEED TO

CHEVY LS GEN 3 - MARK'S 4WD ADAPT ORS

KIT CONSISTS OF:

No. Qty Part No. Description

1 1 LC165473S LUK CHEVY 11" (LOW-PRO)ASSYBLY
2 1 716673A IN-LINE TEMP SENSOR KIT-1-3/8" X 1/2"NPTF
3 1 716314 T/0 BRG. LOW-DIAPH CLUTCH
4 6 716141A GEN-3 FLYWHEELT BOLT 11MM
5 2 716039 SPACER- FOR SLAVE CYLINDER
6 2 713124-PLT TOYOTA L/C V8 SCAB PLT. FRAME
7 1KIT 713088 CHEVY LS1 UNIVERSAL MOUNT KIT
8 3 713039 SPACER BELLHOUSING MOUNT
9 1 713038 L/C BELLHOUSING MOUNT
10 1KIT 712525 L/C CHEV V8 CONV.KIT (MARKS)
11 1 712525-B T/O BUSHING FOR 712525
12 1 711500M FLYWHEEL GEN-3 VORTEC ENGINES
13 3 725002 LOCK WASHER 1/2" PLATED
14 6 723761 3/8"-16 X1" PRESSURE PLATE BOLT
15 2 723738 3/8"-16 X 2-3/4" H.H.C.S. FOR SLAVE CYLINDER
16 2 723704 LOCK WASHER 3/8" ZINC FOR SLAVE CYLINDER
17 3 720043 H.H.C.S. 12mm X 1.75TH X 70mm STRENGTH CLASS 8.8
18 6 720038 LOCK WASHER- 10MM
19 6 720028 10mm X 1.5 35mm LONG SHCS ZINC plated
20 2 720015 10mm FLAT WASHER FOR SLAVE CYLINDER

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components
will void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly
recommend that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We
recommend that a service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally
available at automotive dealerships and parts stores.

ADVANCE ADAPTERS INC. P/N: 713027-EK

P.O. Box 247, 4320 Aerotech Center Way
Paso Robles, CA 93447 PAGE 2 OF 2
Telephone: [phone] Fax: [phone] Page Rev . Date: 01-31-14

TOYOTA LAND CRUISER 4 SPEED T O

CHEVY LS GEN 3 - MARK'S 4WD ADAPT ORS

SPECIAL GEN 3

11" CLUTCH

NOTE:

1. Thrust tube must be installed prior to release bearing and ring assembly.

2. Make sure that bearing support ring is installed first and then release bearing collar.

3. If assembled before, you will find that the assembly will not fit through flywheel housing bore.

4. This kit fits with both the stock Toyota cast iron and stamped steel release arms.

5. The new release collar is designed to fit both release arms. When using the cast iron arm, new clips have
been provided to connect the arm to the collar. The small square metal blocks need to be installed on
the new collar and Loctite into position.

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components
will void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly
recommend that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We
recommend that a service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally
available at automotive dealerships and parts stores.