Advance Adapters 712523 User Manual

ADVANCE ADAPTERS INC. P/N: 712523

P.O. Box 247, 4320 Aerotech Center Way
Paso Robles, CA 93447 PAGE 1 OF 2
Telephone: [phone] Fax: [phone] Page Rev. Date: 10-23-96

TOYOTA L/C 3 SPEED TRANSMISSION TO

CHEVY V8 ENGINES

KIT CONSISTS OF:
No. Qty Part No. Description

1. 1 711525 ADAPTER PLATE

2. 1 716170 PILOT BUSHING

3. 1 716222 BEARING RETAINER

4. 1 716514 GASKET

5. 1 716719 SEAL (Toyota #90311 28004)

6. 4 723116 5/16" LOCK WASHER

7. 2 725002 1/2" LOCK WASHER

8. 2 725008 H.H.C.S. 1/2"-13 x 1-1/2" LONG

9. 4 720010 S.H.C.S. 8mm x 40mm

10. 2 725017 S.H.C.S. 1/2"-13 x 1-3/4" LONG

11. 2 725019 1/2" HIGH COLLAR LOCK WASHER
12 1 TLC001 LAND CRUISER INSTRUCTION MANUAL

INSTALLATION INSTRUCTIONS:

When converting the Toyota 3 speed transmission, you will find that the original input shaft length is approximately 3/
8" too long for use with the Chevy bellhousing. The adapter plate and special bearing retainer will provide the necessary
spacing to pull the transmission back and make the necessary lengths compatible for the Chevy bellhousing. Make sure
that the new seal is installed with the open side towards the transmission and that the gasket is properly installed between
the new retainer and the front of the transmission. New metric bolts have been included for installation of the thicker
bearing retainer. When using this transmission on V8 conversions, driveshaft modifications will be required.

1. Remove the original 3 speed bearing retainer and install the new retainer equipped with the new seal. Be sure gasket
is used between transmission and bearing retainer and use the longer metric bolts and lock washers for installation.
Make sure that the bolts do not protrude into the transmission gear assembly.

2. Fit the new steel plate onto the front of the Toyota 3 speed transmission and make sure that all bolts will have
necessary clearance.

3. Drill the lower transmission mounting holes out for clearance of the new 1/2" bellhousing bolts.

4. Install new pilot bearing into engine crank. Make sure that the contact with the Toyota transmission input shaft
is correct.

5. Bolt the transmission to the Chevy bellhousing using the hex bolts in the upper locations and the socket head bolts
in the lower locations.

6. The following Chevy parts will be necessary:

Clutch Release Lever
Pressure Plate 11" - Centerforce CF165473S
Clutch Disc with 1-1/8"-10 Spline
Flywheel - 168 tooth
Bellhousing with Small Index Diameter of 4.686" (must have 14" inside clearance)

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void
any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend that
you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a service
manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive dealerships
and parts stores.

ADVANCE ADAPTERS INC. P/N: 712523

P.O. Box 247, 4320 Aerotech Center Way
Paso Robles, CA 93447 PAGE 2 OF 2
Telephone: [phone] Fax: [phone] Page Rev. Date: 02-14-03

TOYOTA L/C 3 SPEED TRANSMISSION TO

CHEVY V8 ENGINES

NOTES:

1. Be sure to grease inside pocket diameter of bearing, this will provide lubrication on the bearing retainer.

2. Release bearing should have .060" clearance between flywheel fingers and face of bearing.

3. Clutch disc should have .030" clearance between flywheel and disc when fully disengaged.

4. The 10.500" clutch assembly and small flywheel is not recommended. The 168 tooth flywheel should
be used if at all possible.

5. Do not use original Toyota Land Cruiser clutch disc.

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void
any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend that
you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a service
manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive dealerships
and parts stores.