Advance Adapters 712514 User Manual

ADVANCE ADAPTERS INC. P/N: 712514

P.O. Box 247, 4320 Aerotech Center Way
Paso Robles, CA 93447 PAGE 1 OF 2
Telephone: [phone] Fax: [phone] Page Rev. Date: 11-05-12

JEEP T18 4 SPEED TRANSMISSION TO

FORD V8 ENGINES 1965 & UP

KIT CONSISTS OF:
No. Qty Part No. Description

1. 1 711512 ADAPTER CASTING

2. 1 716016 TRANSMISSION INPUT SHAFT (17T)

3. 1 716173 PILOT BEARING

4. 1 716724 C/R SEAL NO. 11734

5. 4 723119 S.H.C.S. 5/16"-18 x 1-1/4"

6. 2 724309 H.H.C.S. 7/16"-14 x 2" LONG

7. 1 761019 BEARING RETAINER

8. 1 JP001 JEEP INSTRUCTION MANUAL

INSTALLATION INSTRUCTIONS:

When converting this Jeep 4 speed transmission, you must change the transmission input shaft to the new style that
has been furnished in this kit.

If this kit is being used on a T18 transmission, then the stock needle bearings will be retained. The T18 transmission
also used two sizes of shifter synchronizer rings. If the transmission you have has a synchronizer ring that is too large,
you will then be required to purchase P/N TT87-D14 from your Border Auto Parts 619-461-0171.

1. Install new shaft.

2. Install pilot bushing into the engine crank shaft.

3. Bolt the bearing retainer to the adapter plate using the 4 bolts supplied.

4. Install the new oil seal with the open side towards the transmission and make sure that it locates directly over the
transmission into the adapter. New bolts have been provided to go through both the transmission and adapter plate
and thread into the new bellhousing.

5. Place the adapter plate to the bellhousing, apply RTV silicone on the adapter plate and then index the transmission
into the adapter. New bolts have been provided to go through both the transmission and adapter plate and thread
into the new bellhousing.

6. The following Ford parts will be necessary:

OPTIONAL ITEMS:
Qty Part No. Description

1 716177 CLUTCH REL. ARM

Clutch Release Bearing
Clutch Release Lever
Pressure Plate
Clutch Disc with 1-1/16"-10 spline
Flywheel
Bellhousing with small index diameter of 4.686"

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void
any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend that
you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a service
manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive dealerships
and parts stores.

ADVANCE ADAPTERS INC. P/N: 712514

P.O. Box 247, 4320 Aerotech Center Way
Paso Robles, CA 93447 PAGE 2 OF 2
Telephone: [phone] Fax: [phone] Page Rev. Date: 10-20-10

JEEP T18 4 SPEED TRANSMISSION TO

FORD V8 ENGINES 1965 & UP

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void
any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend that
you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a service
manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive dealerships
and parts stores.