Advance Adapters 712505 User Manual

ADVANCE ADAPTERS INC. P/N: 712505

P.O. Box 247, 4320 Aerotech Center Way
Paso Robles, CA 93447 PAGE 1 OF 2
Telephone: [phone] Fax: [phone] Page Rev. Date: 06-25-07

JEEP T90 3 SPEED TRANSMISSION TO

FORD V8 ENGINES 1965 & UP

KIT CONSISTS OF:

No. Qty Part No. Description

1. 1 711504 ADAPTER CASTING

2. 1 716172 PI LO T B USH IN G (.625" I.D.)

3. 1 716706 NATIONAL SEAL #482208

4. 4 723119 S.H.C.S. 5/16"-18 x 1-1/4" LONG

5. 1 761019 BEARING RETAINER

6. 1 JP001 JEEP INSTRUCTION MANUAL

INSTALLATION INSTRUCTIONS:

When replacing a 4 cylinder engine, a new transmission input shaft, Advance Adapter Part No. 716014, will be required.
A new cluster gear, Part No. 716018, is required when replacing a 16 tooth input shaft. Most conversions will require
the transfer case to be moved forward in order to obtain a good engine position. This will require driveshaft
modifications. The engine should be offset towards the driver's side by approximately 1" in order to allow for driveshaft
and starter motor clearance.

1. Install pilot bushing into the engine crank shaft.

2. Remove the bearing retainer from the front of the 3 speed transmission and cut the snout off as illustrated to an
overall length of 1-5/8". Remove the seal and install the new seal provided with the kit. The seal must have the
open side towards the transmission.

3. The following Ford parts will be necessary:

Clutch Release Bearing
Clutch Release Lever
Pressure Plate
Clutch Disc with 1-1/8"-10
Flywheel
Bellhousing with small index diameter of 4.848"

OPTIONAL ITEMS:

Qty Part No. Description

1 716177 CLUTCH REL. ARM
1 716011 T90 RETAINER
1 716014 T90 INPUT SHAFT

When replacing a 4 cylinder, it is necessary to
purchase the 716014 Input shaft & the 716011
Retainer.

4. Bolt the new bearing retainer to the front of the adapter housing using the 4 bolts supplied.

5. Bolt the adapter plate to the new bellhousing. The bellhousing must be from a 1965 or newer Ford engine. Early
model bellhousings are not applicable for use with this kit.

6. Bolt the transmission to the adapter plate using the original bolts.

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void
any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend that
you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a service
manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive dealerships
and parts stores.

ADVANCE ADAPTERS INC. P/N: 712505

P.O. Box 247, 4320 Aerotech Center Way
Paso Robles, CA 93447 PAGE 2 OF 2
Telephone: [phone] Fax: [phone] Page Rev. Date: 10-29-01

JEEP T90 3 SPEED TRANSMISSION TO

FORD V8 ENGINES 1965 & UP

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void
any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend that
you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a service
manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive dealerships
and parts stores.