Advance Adapters 50-8200 User Manual

ADV ANCE ADAPTERS INC. P/N: 50-8200

P.O. Box 247, 4320 Aerotech Center Way Old Part No: 711082
Paso Robles, CA 93447 PAGE 1 OF 3
Telephone: [phone] Fax: [phone] Page Rev. Date: 04-25-97

FORD C4 3 SPEED AUTOMATIC TO

TOYOTA LAND CRUISER 3 SPEED T/C

KIT CONSISTS OF:
No. Qty Part No. Description

1. 1 51-7800 ADAPTER (Ref: 711178)

2. 1 51-8100 CASTING (Ref: 711181)

3. 1 52-1500 SPUD SHAFT (Ref: 711315)

4. 1 52-8200 C4 SHAFT (TH350 Spline) (Ref: 711382)

5. 1 716061 VENT ASSY. / C4 CASTING

6. 1 716301 BEARING

7. 1 716507 GASKET (Toyota T/C)

8. 1 716700 SEAL

9. 1 716733 "O"-RING

10. 5 723721 3/8"-16 x 1" H.H.C.S.

11. 3 724345 H.H.C.S. 7/16"-14 x 5" LG

12. 2 724349 7/16"-14 x 1-1/2" H.H.C.S.

13. 1 728701 NUT

14. 1 728702 WASHER

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will
void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend
that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a
service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive
dealerships and parts stores.

ADV ANCE ADAPTERS INC. P/N: 50-8200

P.O. Box 247, 4320 Aerotech Center Way Old Part No: 711082
Paso Robles, CA 93447 PAGE 2 OF 3
Telephone: [phone] Fax: [phone] Page Rev. Date: 07-16-92

FORD C4 3 SPEED AUTOMATIC TO

TOYOTA LAND CRUISER 3 SPEED T/C

FORD C4 AUTOMATIC TRANSMISSIONS:

The Ford C4 automatic transmission has a case length of 11-3/16", 11 bolts for holding the oil pan in position and has a
removable front bellhousing. The bellhousing is available for 289, 302, 351C and 351W Ford engines. There is two
different main case options that are referred to as either a "flared case" or a "step case". The step case has the oil dipstick
entering the transmission case, while the flared case has the dipstick entering the transmission pan. Both models are
acceptable for use with all the Advance Adapter kits. The V8 bellhousing length is 5-7/8" and can be interchanged with
the 2.8 V6 bellhousing on Bronco II and Ranger conversions. On transmissions 1970 and earlier, the pump shaft was
slightly longer and will require shortening for use with our new output shafts. The transmission should be assembled by
a competent mechanic to make sure the transmission operates correctly. The new shaft should be identical to the original
shaft with the only exception being the new splined area for use with the transfer case adapter.

Most C4 transmissions have a breather in the main case of the transmission. There are a new applications where the breather
is installed into the tailhousing. We have included with your kit a new breather for installation into your new adapter housing
only on transmissions that require vented tailhousings. The installation procedure is to simply drill and 11/32" hole in the
top portion of the new tailhousing and press the new vent plug into position. If this is not done on transmissions equipped
with vented tailhousings, then you will have extreme pressure and leakage out the transmission dip stick.

When installing the new tailhousing on the back of your transmission, it may be necessary to trial fit the adapter in position
and make sure that the linkage has all the proper clearance on the internal cavity of the adapter. The bolting of the tailhousing
to the main transmission may need a slight amount of grinding for proper head clearance due to the aluminum sand casting
tolerances.

On installations using a 2-piece main shaft, make sure the shaft and coupler do not bottom out. We have found on occasions
that the transmission output shaft may be slightly longer than we have allowed for; and when coupling into the transfer
case spud shaft, we find a small amount of interference. The adapter housing and spud shaft must be assembled without
interference. DO NOT FORCE THE NEW TAILHOUSING AND TRANSFER CASE TOGETHER. If assistance is
needed, please feel free to call the number listed above.

With the transmission and shaft assembled, you are now ready to assemble the rear adapter plate and transfer case. Press
the new bearing supplied onto the spud shaft with the snap ring towards the threaded end. Press the bearing and shaft
assembly into the back of the adapter plate, Part No. 711178. Make sure that the bearing seats properly. With the adapter
assembled, you can now insert the adapter plate, spud shaft and bearing into the transfer case. Refer to transfer case
instructions for correct procedure of assembling the gears. Bolt the adapter plate into position using the (5) new bolts
provided.

You should now have the transfer case assembled with one adapter and the transmission assembled with the new adapter
housing and main shaft. Install the "O"-ring seal in the proper location and assemble the two units together. Use the (6)
bolts and lock washers to secure the two adapters. DO NOT FORCE THE MALE AND FEMALE CONNECTION. The
adapters should come together evenly. Caution should be taken to the possibility of the male transmission shaft bottoming
out inside the female spud shaft splines.

All installations will require the use of a transmission cooler. The cooler can be either installed in the radiator or a remote
location is acceptable. The transmission shift control can either be a Hurst floor mounted type shifter or sometimes the
existing column shift can be modified on certain applications.

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will
void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend
that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a
service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive
dealerships and parts stores.