Advance Adapters 50-7300 User Manual

ADVANCE ADAPTERS INC. P/N: 50-7300

P.O. Box 247, 4320 Aerotech Center Way Old Part No: 711073
Paso Robles, CA 93447 PAGE 1 OF 3
Telephone: [phone] Fax: [phone] Page Rev. Date: 08-13-14

TURBO 350 TO T OYOTA LAND CRUISER

1963 - 1973 (3 SPEED)

KIT CONSISTS OF:
No. Qty Part No. Description

1. 1 51-7300 CASTING (Ref: 711173)

2. 1 52-1500 SHAFT (Ref: 711315)

3. 1 52-7300 TH350 SHAFT (12-3/4" O.A.L.)
4 . 1 Pack 714203 BOLT PACK (50-7300)

5. 1 716062 NYLON BUSHING FOR T350 OUTPUT SHAFT

(CUSTOMER MUST INSTALL)

6. 1 716301 BEARING

7. 1 716507 T/C GASKET

8. 1 716511 "O"-RING

9. 1 728701 NUT

10. 1 728702 7/8" FLAT WASHER

11. 4 723704 3/8" LOCKWASHER

12. 4 723723 3/8"-16 x 1-1/2" H.H.C.S.

13. 1 TLC001 LAND CRUISER INSTRUCTION MANUAL

OPTIONAL ITEM:
Qty Part No. Description

1 716004 CROSSMEMBER ASSY

1 715521 T/C LINKAGE BRKT.

(Includes #716003 Mount)

(If not using a vacuum
controlled shifter)

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will
void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend
that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a
service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive
dealerships and parts stores.

ADVANCE ADAPTERS INC. P/N: 50-7300

P.O. Box 247, 4320 Aerotech Center Way Old Part No: 711073
Paso Robles, CA 93447 PAGE 2 OF 3
Telephone: [phone] Fax: [phone] Page Rev. Date: 08-13-14

TURBO 350 TO T OYOTA LAND CRUISER

1963 - 1973 (3 SPEED)

INSTALLATION INSTRUCTIONS:

This kit is for the GM Chevy and Buick TH350 3 speed automatics to all Toyota Land Cruiser transfer cases, 1963-73. This kit will
not work with FJ60 transfer cases. The design of this kit utilizes two shafts. The first shaft is a modified stock TH350 output shaft
that we have cut to the proper overall length of 12-3/4". The shaft should be installed into your new TH350 transmission by a
competent mechanic. This shaft is compatible with all TH350 transmissions. The new spud shaft should be pressed onto the new
rear bearing so the external snap ring is towards the threaded end of the shaft. The spud shaft and bearing can now be installed
from the transfer case side of the adapter and pressed into the bearing recess. The snap ring that is on the outside diameter of the
bearing will keep the shaft in the proper location. You can examine the transfer case face to see the slight snap ring recess that
will trap the bearing snap ring and establish the correct location. Due to the extreme length of this transmission and adapter,
driveshaft modifications will be required on almost every installation. On Land Cruiser conversions, you will find that the overall
assembled length of the new transmission and adapter will just barely fit between the original rear crossmember and the radiator
location. We suggest that the rear drivetrain be supported by a crossmember underneath the adapter. We offer a new crossmember
assembly that includes the #716003 rubber mount for supporting your transmission assembly. The new crossmember assembly
is Part No. 716004. The right side of the adapter has two tapped holes to assist you in mounting a transfer case linkage bracket
for support of your pivot stud. If your 3 speed transmission was equipped with mechanical transfer case shift control, then you
can purchase Part No. 715521 for mounting the linkage onto the new transmission.

GM TH350 3 SPEED AUTOMATIC:

The GM TH350 has a case length of 21-1/2", 13 bolts for holding the oil pan in position, and is available in two different engine
to transmission bolt patterns. The case is available with a Chevy bolt pattern that has the top two holes 8-1/4" apart, or in a Buick
bolt pattern that has the top two holes 7" apart. The rear side of the transmission case should have a square bolt pattern that uses
4 bolts. Some kits will simply require the existing 2WD shaft to be shortened for use with the new coupler. Make sure that you
measure the cutoff location correctly in order to avoid any additional expenses. All TH350 output shafts will have 27 spines. The
speedometer gear is normally located in the tailhousing, but when adapting it to the transfer case, the location will change to the
back side of the transfer case. The rear transmission support is located in the main case just forward of the tailhousing connection.
This can be used for supporting the crossmember on some installations, but most of the our kits provide support on the new adapter
housing.

When installing the new transfer case adapter, make sure that the coupler and the output shaft do not bottom out. We have found
on occasion that a transmission output shaft may be slightly longer than what we have allowed for; and when coupling into our
new spud shaft, we find a small amount of interference The adapter housing and spud shaft must be assembled to the back of the
transmission without interference. DO NOT FORCE THE NEW TAILHOUSING ONTO THE TRANSMISSION. If assistance
is needed, please feel free to call us on our toll free line, [phone].

When assembling the adapter housing to the transmission case, we have provided you with a new square type "O"-ring seal to
prevent fluid leakage. This seal is a stock GM item that is used on all TH350 installations. On most installations, a slight pan
modification may be required for clearance of the front Universal yoke.

In order to allow for additional front driveline clearance, we recommend that the engine and transfer case be offset to the driver's
side on vehicles having front driveshafts located on the passenger side. On Land Cruiser conversions, this is achieved by offsetting
your drivetrain approximately 1" of centerline or by using one of the front driveshaft kits listed in the Land Cruiser manual.

If you have selected a transmission that has the old style modulator, then we recommend the use of our adjustable modulator, Part
No. 716010. This will also allow for additional driveshaft clearance. All installations will require the use of a transmission cooler.
The cooler can be either installed in the radiator or a remote location is acceptable.

Loctite should be used on all fasteners.

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will
void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend
that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a
service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive
dealerships and parts stores.