Advance Adapters 50-5804 User Manual

ADVANCE ADAPTERS INC. P/N: 50-5804

P.O. Box 247, 4320 Aerotech Center Way New Item: (12/00)
Paso Robles, CA 93447 PAGE 1 OF 3
Telephone: [phone] Fax: [phone] Page Rev. Date: 12-04-06

FORD NP435 4 SPEED TRANSMISSION TO

TOYOTA 4WD TRUCK 1979-95 (21 SPLINE)

KIT CONSISTS OF:

No. Qty Part No. Description

1. 1 51-5800 ADAPTER CASTING

2. 1 52-3800 NP435 MAINSHAFT WITH 23 SPLINES (Shortened 1.440")

3. 1 52-5804 COUPLER SHAFT

4. 1 716015 SPECIAL BEARING RETAINER

5. 1 716063 COVER PLATE

6. 1 716308 BEARING

7. 1 716450 SNAP RING (GM#3785205)

8. 1 716456 SNAP RING (T/A#N5000-334)

9. 1 716512 GASKET

10. 1 716564 GASKET

11. 1 716734 SEAL (National #471833)

12. 4 720040 METRIC BOLTS

13. 2 725025 STUD BOLT 1/2"-13 x 1-1/4" LG

14. 2 725029 H.H.C.S. 1/2"-13 x 1-1/4" LG

15. 1 TT001 TOYOTA TRUCK INSTRUCTION MANUAL

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will
void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend
that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a
service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive
dealerships and parts stores.

ADVANCE ADAPTERS INC. P/N: 50-5804

P.O. Box 247, 4320 Aerotech Center Way New Item: (12/00)
Paso Robles, CA 93447 PAGE 2 OF 3
Telephone: [phone] Fax: [phone] Page Rev. Date: 12-19-00

FORD NP435 4 SPEED TRANSMISSION TO

TOYOTA 4WD TRUCK 1979-95 (21 SPLINE)

BORG WARNER NP435 TRANSMISSION:

The NP435 transmission can be identified by a case length of 10-7/8" . The front bolt pattern on the Ford transmissions will
have an 8-1/2" x 6-1/4" bellhousing pattern with a bellhousing pilot diameter of 4.848". This adapter will work on all Toyota
4WD trucks, 1979 through November 1995.

Before you begin to assemble your transmission, you must make sure that you have received the correct main shaft. The
spline on the end of the shaft must have 23 teeth. When assembling the gears onto the new main shaft, make sure that all
gears have the proper end clearance required for oiling. Make sure that all transmission assembly work is done by a competent
mechanic. All surfaces must use gaskets to prevent oil leakage.

The coupler in this kit is made for a 21 spline male shaft that protrudes from the front of your transfer case. Make sure
that the coupler and the output shaft do not bottom out. We have found on occasion that a transmission output shaft may
be slightly longer when we have allowed for; and when coupling into our new spud shaft, we find a small amount of
interference. The adapter housing and spud shaft must be assembled to the back of the transmission without interference.

DO NOT FORCE THE NEW TAILHOUSING ONTO THE TRANSMISSION. If assistance is needed, please feel free

to call the number listed above.

When replacing transmissions that were equipped with turbo-charged 4 cyl. engines, they require a 23 spline coupler. The
linkage on the Toyota transfer cases will vary. Some have the control lever on the tailhousing of the transmission, while
others have it on the transfer case. This adapter can be used with either style and if the opening is not used on the top of
the new housing you will need to cover the square opening.

When bolting the adapter to the main transmission case, you must use two studs in the lower two holes of the adapter. A
slight modification may be necessary to obtain the proper clearance around the lower bearing cover of the stock transmission.
Make sure the bearing retainer clip found on the front side of some transfer cases is removed prior to assembly of the new
adapter. See illustration.

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will
void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend
that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a
service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive
dealerships and parts stores.