Advance Adapters 50-0226 User Manual
ADVANCE ADAPTERS INC. P/N: 50-0226
P.O. Box 247, 4320 Aerotech Center Way New Item: (09/97)
Paso Robles, CA 93447 PAGE 1 OF 3
Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 12-18-09
DODGE NV4500 5 SPEED23 SPLINE OUTPUT
TO TOYOTA L/C 16 SPLINE
KIT CONSISTS OF:
No. Qty Part No. Description
1. 1 51-0224 ADAPTER CASTING
2. 1 52-0226 16 SPLINE SPUD SHAFT (23T INTERNAL)
3. 1 K it 715532 TRANSFER CASE LINKAGE BRKT. ASSY.
4. 1 716199 RETAINER
5. 1 716301 SEALED BEARING
6. 1 716507 GASKET
7. 8 720046 10mm-1.5 x 40mm LONG
8. 2 723735 3/8" FLAT WASHER
9. 2 723739 3/8"-16 x 7/8" H.H.C.S.
10. 5 724303 7/16" LOCKWASHERS
11. 8 724324 7/16" HIGH COLLAR LOCK WASHER
12. 3 724345 7/16" x 14 x 5" HEX HEAD BOLT
13. 2 724349 7-16" x 14 x 1-1/2" H.H.C.S.
14. 1 728701 NYLON NUT
15. 1 728702 7/8" FLATWASHER
16. 1 TLC001 LAND CRUISER INSTRUCTION MANUAL
17. 1 NV001 NV INSTRUCTION MANUAL
NOTE:
This adapter kit has an overall transmission assembled length of 18.750". This kit will work ONLY with Dodge NV4500
gas transmissions having 23 spline output.
CAUTION:
There are two 3/8" holes located on the side of the adapter for the mechanical shifter linkage. If your vehicle
has a 3 speed vacuum type shifter, these holes are not going to be used. They will need to be plugged with the
hardware provided and small amount of silicone.
SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components
will void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly
recommend that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We
recommend that a service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally
available at automotive dealerships and parts stores.
ADVANCE ADAPTERS INC. P/N: 50-0226
P.O. Box 247, 4320 Aerotech Center Way New Item: (09/97)
Paso Robles, CA 93447 PAGE 2 OF 3
Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 06-06-01
DODGE NV4500 5 SPEED23 SPLINE OUTPUT
TO TOYOTA L/C 16 SPLINE
NOTE:
1. This adapter is designed for exclusive use of the Dodge 4WD 23 spline output version of the NV Model 4500
transmission. You must use this transmission due to the length and spline size of the output shaft. The shaft must
be shortened to the 5.420" cutoff length (see Page 3). In order to cut the shaft off, you will need to remove the
tailhousing. The shaft can be cutoff using and abrasive cutoff saw or a skill saw equipped with a special metal cutting
blade. Be sure to use safety glasses during this procedure.
2. The assembly of the adapter plate to the transfer case should be very much like the originally transmission that is being
replaced. A new flat washer and nut are provided for the early model vehicles to hold the two gears in position.
3. The alignment between the new adapter plate and transfer case must be performed by the new bearing that has been
included with the adapter. This sealed bearing will have the external snap ring on the outside of the adapter similar
to the original transmission. This will prevent the special transmission fluid of the New Venture gear box from mixing
with the transfer case fluids. When installing the adapter to the NV4500 make sure the stock dowel pins are
in the transmission.
4. When using this transmission assembly with a 6 cylinder Toyota engine, you may need to modify the gas tank area
on 1979 and newer vehicles. It would be advisable that your vehicle be equipped with a suspension lift and you should
plan on removal of the stock rear crossmember. A new Advance Adapter crossmember #716022, will be required.
This transmission assembly is the very shortest possible and careful planning is a must when performing the
installation with the stock 6 cylinder.
5. The transfer case shift controls will need to be modified for use with the new transmission. A new bracket #715532
has been supplied.
SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components
will void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly
recommend that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend
that a service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at
automotive dealerships and parts stores.
Loading...