Adtran NetVanta 4305 Quick Start Guide

For more detailed documentation, visit us online at www.adtran.com

Quick Start Guide

NETVANTA 4305 (SYSTEM) P/N 1200890L1

TD RD LNK

LAN 2

TD RD LNK

STATUS

WAN DBU

NET 1

LAN 1

TD RD

WAN DBU

NET 2

INSTALL THE NETWORK INTERFACE MODULE (NIM)

1. Verify the unit is not connected to a power source.

2. (Optional) To install the Dial Backup Interface Module (DIM), carefully align the P1 connector on the NIM with the J1 connector on the DIM. Using only fingertip pressure to ensure that neither circuit board bends or flexes, firmly seat the connectors. Secure the DIM to the NIM using the supplied screws and standoff posts.

3. Slide the NIM into the option slot until the module is firmly positioned against the back of the chassis.

4. Secure the push pins at both edges of the module.

5. (Optional) To install the Wide Slot Interface Module, align the module with Slot 3 and slide the module into the chassis until it is firmly positioned against the backplane connectors. Secure by tightening the screws.

CONNECT TO THE NETVANTA 4305 CONSOLE

Before connecting to the NetVanta 4305 CONSOLE interface you will need the following items: VT100 terminal or PC (with VT100 terminal emulation software) and a straight-through serial cable with a DB-9 (male) connector on one end and the appropriate interface for your terminal (or PC) on the other.

1. Connect the DB-9 (male) connector of your serial cable to the CONSOLE port on the rear panel of the unit.

2. Connect the loose end of the serial cable to the VT100 terminal or PC (with terminal emulation software).

3. Open a VT100 terminal session to the NetVanta 4305 using the following settings: 9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press <Enter> to activate the ADTRAN Command Line Interface.

4. Enter enable at the > prompt.

5. Enter the password when prompted. The default password is password.

WIDE SLOT 1

STATUS ACTIVITY TEST

LED DESCRIPTIONS

For these LEDs…

STATUS

NET 1/ NET 2 WAN

NET 1/ NET 2 DBU

NET 1/NET 2 TD/RD

LAN 1/ LAN 2 LNK

LAN 1/ LAN 2 TD/RD

This activity…

Green (blinking)

Green (solid) Power is on and self-test passed.

Red (solid)

Yellow (solid) Unit is in test.

Off No NIM is installed, or interface is administratively down.

Green (solid) Link is up and everything is operational.

Red (solid)

Yellow (solid) Unit is in test.

Off No DIM is installed.

Green (solid)

Green (blinking)

Red (solid)

Yellow (solid) Unit is in test.

Green (blinking)

Off There is no activity on the WAN or DBU port.

Green (solid) 10BaseT Ethernet link is up.

Yellow (solid) 100BaseT Ethernet link is up.

Green (blinking)

Off There is no activity on the Ethernet port.

NetVanta 4305

Indicates that…

Unit is powering up. On power-up the STAT LED blinks rapidly for five seconds, during which time the user may escape to boot mode from the console port.

Power is on, but the self-test failed or the boot mode (if applicable) code could not be booted.

An alarm condition is occurring on the WAN interface, or there is a self-test failure.

DIM is ready. For the ISDN BRI DIM, green solid indicates that the negotiation with the switch is complete.

Unit is in dial backup.

An alarm condition is occurring on the DBU interface, or there is a self-test failure.

There is activity on the WAN or DBU port.

There is activity on the Ethernet port.

Quick Start Guide

CONSOLE

For more detailed documentation, visit us online at www.adtran.com

NETVANTA 4305 (SYSTEM) P/N 1200890L1

ETH 0/2

100- 250VAC, 0.75A

WAN-T1 DSX-1 DBU WAN-T1 DSX-1 DBU

WAN-T1 DSX-1 DBU

50/60Hz

LED DESCRIPTIONS (CONTINUED)

For these LEDs…

WIDE SLOT 1 STATUS

WIDE SLOT 1 ACTIVITY

WIDE SLOT 1 TEST

This activity…

Off Card is not installed.

Green (solid) Card is recognized by the system

Red (solid) Alarm condition with card.

Green (blinking)

Off There is no data activity on card.

Off Card is not in test.

Yellow (solid) Card is in test mode.

Indicates that…

There is data activity on the card (e.g., for the Octal T1 Module, this indicates TD/RD data).

CONSOLE PINOUT

Pin Name Description

1 DCD Data Carrier Detect (output)

2 RD Receive Data (output)

3 TD Transmit Data (input)

SLOT 2 NET/DBUSLOT 3 WIDE MODULE

SLOT 1 NET/DBU

ETH 0/1

ETHERNET PINOUT

Pin Name Description

1 TX1 Transmit Positive

2 TX2 Transmit Negative

3 RX1 Receive Positive

4, 5 — Unused

6 RX2 Receive Negative

7, 8 — Unused

COMMANDS

Refer to the ADTRAN Operating System (OS) Command Reference Guide (provided on the ADTRAN OS Documentation CD) for details on configuring the system using the Command Line Interface.

4 DTR Data Terminal Ready (input)

5 SG Signal Ground

6 DSR Data Set Ready (output)

7 RTS Request to Send (input)

8 CTS Clear to Send (output)

9 RI Ring Indicate (output)