ADTRAN NetVanta 300 User Manual

NetVanta 300 Series Router P/N 1200422L1, 1200423E1/L1, 1200426E1/L1, 1200429L1

Quick Start Guide

GETTING STARTED

Two configuration methods are available for your NetVanta router:

• Web-based GUI

• AOS Command Line Interface (CLI)

The GUI lets you configure the main unit settings and provides online guidance and explanations for each setting. However, using the AOS CLI may be necessary for more advanced configurations.

ACCESS THE GUI

You may access the web-based GUI from any web browser on your network by following these steps:

1. Connect the router to your PC using one of the ETHERNET ports on the back of the unit.

2. During bootup your PC will obtain an IP address from the NetVanta 300 Series unit’s DHCP server. By default, both the DHCP and HTTP servers are enabled.

3. Enter the unit’s IP address in your browser address line. The default IP address is 10.10.10.1.

4. You will then be prompted for the username and password (the default settings are admin and password).

5. The initial GUI screen appears.

6. Click on Getting Started in the System menu on the left side of your screen and follow the on- line instructions.

For security purposes, you should set up an admin password immediately. Use the Passwords page of the Web GUI to change this password.

For more detailed documentation, visit us online at www.adtran.com.

CONFIGURE THE ATM PVC

1. Click on the Getting Started link under the System menu. This brings up a side bar page.

2. Click on Step 1 - Configure the Public Interface at the top of the side bar page to open the ATM PVC page.

3. Enter the PVC number and select an Interface Mode. Usually this is PPP or PPPoE; however, if IP routing is chosen, you will need to enter an IP address.

4. Click Apply. If PPP or PPPoE is selected as the Interface Mode, you will be taken to the PPP page after clicking Apply. Here you will need to select the type of authentication needed, authentication passwords, and the Address Type. In most cases you will want the

Address Type to be Negotiated. Click Apply when all the information is complete.

ACCESS THE CLI

If needed, you can access the AOS CLI via a Telnet session.

1. Telnet to the unit’s IP address. The default IP address is 10.10.10.1.

2. You will then be prompted for the username and password (the default settings are admin and password).

3. Enter enable at the > prompt.

4. Enter the enable password when prompted. The default password is password.

FACTORY DEFAULT SWITCH

• If the factory default switch (shown in the back panel illustrations on the next page) is pressed during bootup, the unit will stay in bootstrap mode. Since the unit has no serial port, Telnet has been built into the boot code. The default IP address is 10.10.10.1.

• If the factory default switch is pressed and held for 5 seconds after boot, the ETHERNET interface on the NetVanta 340 (or the VLAN 1 interface on the NetVanta 344 and NetVanta 347) will default to 10.10.10.1 and all access policies will be removed from that interface.

• If the factory default switch is pressed and held for 30 seconds, a default configuration will overwrite your existing configuration and reboot the unit.

The default switch must be pressed WHILE the power light is flashing green. Do not press the default switch BEFORE the power light is flashing green, as this will cause boot to be missed

By default, the NetVanta unit comes with an ADSL and an Asynchronous Transfer Mode (ATM) port already configured and enabled. The service provider should provide a PVC (VPI/VCI) number which will be used to configure the ATM PVC.

Quick Start Guide

For more detailed documentation, visit us online at www.adtran.com.

NetVanta 300 Series Router P/N 1200422L1, 1200423E1/L1, 1200426E1/L1, 1200429L1

ADSL CONNECTOR PINOUTS

Pin Name Description

1, 2 — Unused

3 T ADSL Tip

4 R ADSL Ring

5, 6 — Unused

NetVanta 340 Rear Panel Layout

ETHERNET PINOUTS

Pin Name Description

1 TX1 Transmit Positive

2 TX2 Transmit Negative

3 RX1 Receive Positive

4, 5 — Unused

NetVanta 344 Rear Panel Layout

6 RX2 Receive Negative

7, 8 — Unused

CONFIGURE YOUR APPLICATION

More detailed documentation for configuring your ADTRAN unit is provided on the ADTRAN OS Documentation CD included in your shipment. For more detail on hardware setup, refer to the

appropriate Hardware Installation Guide. For more detail on configuring your system, refer to the ADTRAN Operating System (AOS) Command Reference Guide, configuration guides, and technical support notes.

NetVanta 347 Rear Panel Layout

Important: For additional details on product features, specifications, installation, and safety, refer to the appropriate Hardware Installation Guide on the ADTRAN OS System Documentation CD shipped with the base unit and available online at www.adtran.com.