ADTRAN MX2810 M13 User Manual
Product Features
■ Affordable DS3 bandwidth
consolidation
■ Built-in 1:1 redundancy
■ Hot-swappable controller
cards and power
supplies
■ SNMP and Telnet management
■ TL1 alarming and provisioning
support
■ Backhaul multiple service
types (T1/E1)
■ Smallest M13 form factor
available
■ Dual redundant load sharing
DC power supplies
■ M13 and C-Bit signaling
support
■ Industry-standard CSU and
NIU loopback codes
■ NEBS Level 3 compliant
■ Industry-leading, 10-year
warranty
Backhaul consolidation of T1 remains an
important function in network operations.
With central office space at a premium,
carriers need an M13 device that provides
cost efficiency,compact size, and built-in
intelligent redundancy. ADTRAN
®
has
applied its industry-leading expertise in
developing carrier class products to the
MX2810
TM
M13 multiplexer. The MX2810
offers bandwidth consolidation at a low price
and in the smallest footprint available in the
industry. Measuring only 1U high in 19-inch
or 23-inch rackmount configurations, this
compact device gives ILECs a powerful tool
for consolidating 28 T1 signals or 21 E1
signals into a T3 circuit.
The MX2810 houses two hot-swappable
controller cards capable of combining independent T1s, E1s, or T1s and E1s on the same
DS3. The two controller cards also provide
built-in 1:1 redundancy for the DS1 and DS3
signals, as well as built-in BERT (Bit Error
Rate Testing) capabilities. When a T1 failure is
detected, the MX2810 will not swap to the
secondary board until it determines that the
failure is hardware-oriented and not a line
failure. This intelligent redundancy feature
minimizes unnecessary hits to the line that
other M13 units may allow.
Like all ADTRAN products, the MX2810
offers comprehensive management options,
including full management and GUI support
from ADTRAN’s Total Access
®
EMS. It features
a VT100 terminal interface for local configuration. To support SNMP and Telnet
management, the MX2810 has an integrated
10Base-T Ethernet port. It has an RS-232 port
for network management, as well as an
RS-485 port for daisy chaining multiple units.
TL1 alarming and provisioning are also
supported.
The MX2810 meets the most stringent
NEBS Level 3 requirements. In addition, the
product is backed by an industry-leading
10-year warranty.
M13 Multiplexer
MX2810 M13 Multiplexer
Specifications are subject to change without notice. MX2810 is a trademark and
ADTRAN and Total Access are registered trademarks of ADTRAN, Inc. All other
registered trademarks and trademarks mentioned in this publication are the property of their respective owners.
ADTRAN, Inc.
901 Explorer Boulevard
Huntsville, AL 35806
P. O. Box 140000
Huntsville, AL 35814-4000
256 963 8000 voice
256 963 8030 fax
877 457 5007 fax back
General Information
800 9ADTRAN
info@adtran.com
www.adtran.com
Pre-Sales
Technical Support
888 5ADTRAN
support@adtran.com
www.adtran.com/support
Where to Buy
800 827 0807
www.adtran.com/where2buy
Post-Sales
Technical Support
800 726 8663
support@adtran.com
www.adtran.com/support
Regional Offices
Dallas, TX
972 830 9070
Denver, CO
303 471 9150
Irvine, CA
949 260 3500
Kansas City, KS
800 471 8649
Newark, NJ
800 471 8656
Ontario, Canada
416 290 0585
Quebec, Canada
877 923 8726
San Antonio, TX
888 223 7671
International Inquiries
+1 256 963 8716 voice
+1 256 963 6300 fax
international@adtran.com
www.adtran.com/international
ADTRAN is a
TL 9000 registered company.
ADTRAN is an
ISO 9001:2000 registered company.
Product Specifications
Mechanical
■
Dimensions: 1.7 in. H x 17 in. W x 7.86 in. D
(4.32 cm H x 43.18 cm W x 19.96 cm D)
■
Weight: 5.5 lb (2.495 kg) (fully redundant)
Interfaces
DS3 Network Interface
■
Channelized DS3
■
Line build out: Short (0 to 50 feet), and
Normal (50 to 450 feet)
■
Framing format: M13 and C-bit parity
■
Line rate: 44.736 Mbps
■
Line interface: 75 ohm BNC coax female connectors
DSX-1 Interface
■
Line build out: 0 to 655 feet
■
Line rate: 1.54 Mbps
■
Line code: AMI or B8ZS
■
Line interface(s): Dual 64-pin Amp connectors
Clocking
■
Network: Receive from DS3 network
■
Local: Internally generated
Diagnostics
DS3 Network
■
ANSI T1.107 compatible loopbacks
■
Line loopbacks
DSX-1 Ports
■
Local and network loopbacks
■
CSU and NIU loopbacks
Performance Monitoring
Local Network Port Statistics
■
Current 15 minute, 24 hour (96 15-minute intervals),
total for 24 hours and cumulative
DSX Ports
■
BP
■
LOS
■
AIS (loop and carrier)
MX2810 M13 Multiplexer
Electrical
■
Power: 48 VDC, 30 W
Regulatory Standards
■
NEBS Level 3
■
FCC Part 15, Class A
■
NRTL Safety Listed
Management
VT100 Craft Interface
■
DB-9 physical connector
■
EIA-232, PC serial port
SNMP/Telnet
■
Integrated 10Base-T Ethernet
TL1 Alarming/Editing
■
RS-232 X.25 port
■
Ethernet
RS-485 Port
■
Allows the daisy-chaining of units
Alarms
■
External alarm contacts for Critical, Major, and Minor
alarms
■
Normally open pinout
■
Alarm cutoff switch
Environmental
■
Operating temperature: –40ºC to 65ºC
■
Storage temperature: –20ºC to 70ºC
■
Relative humidity: Up to 95 percent, noncondensing
Ordering Information
Equipment Part #
MX2810 Multiplexer Chassis 1185001L1
MX2810 DS3 Controller Card 1185002L2
MX2810 DC Power Supply Unit 1185003L1
MX2810 Test Access Module 1185005L1
MX2810 Redundant System 4185001L5
MX2810 Nonredundant System 4185001L8
6118500xL1-8C February 2004
Copyright © 2004 ADTRAN, Inc.
All rights reserved.
M13 Multiplexer
Network
DS3
28 T1s/21 E1s
MX2810
Loading...