Adtran Installing the NetVanta 1224 Quick Start Guide

For more detailed documentation, visit us online at www.adtran.com

Quick Start Guide, 61200500L1-13B, November2003

TechnicalSupport 1-888-4ADTRAN (1-888-423-8726)

Quick Start Guide

CONNECT THE CONSOLE INTERFACE

To establish a connection to the NetVanta 1224 (1224ST) Switch’s CONSOLE interface, you need the following items:

• VT100 terminal or PC (with VT100 terminal emulation software)

• Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate interface for your terminal or PC communication port on the other end

1. Connect the DB-9 (male) connector of your serial cable to the CONSOLE port on the rear panel of the switch.

2. Connect the other end of the serial cable to the terminal or PC.

3. Insert the connector of the provided power cord into the power interface on the rear panel of the unit, and plug the cord into a standard electrical outlet.

4. Once the switch has powered up, open a VT100 terminal session using the following settings: 9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press <Enter> to activate the ADTRAN operating system command line interface (AOS CLI).

INSTALLING THE NETVANTA 1224 (1224ST) SWI TCH P/N 1200500L1/1200504L1

CONFIGURE THE UNIT’S IP ADDRESS

Configure the IP address and subnet mask by following these steps. If you are not sure what IP address to assign, please contact your network administrator.

1. Enter enable to activate the Enable command security mode.

2. When prompted, enter the enable password (the default password is password).

3. Enter config terminal to activate the Global configuration mode.

4. Enter interface vlan 1 to access the configuration parameters for the VLAN (virtual LAN) interface.

5. Enter ip address 10.26.12.12 255.255.255.0* to assign an IP address and subnet mask to the VLAN interface. Depending on your network configuration, you may need to set a default gateway as well.

*Note: These are example entries only. Modify them to match your configuration.

6. Enter no shutdown to activate the virtual interface to pass d ata.

7. Enter end to return to the Global configuration mode.

8. Enter copy running-config startup-config to save the running configuration to the unit’s non-volatile memory (NVRAM).

Switch> Switch>enable Password: Switch#configterm Switch(config)#interface vlan 1 Switch(config-vlan 1)#ip address 10.26.12.12 255.255.255.0 Switch(config-vlan 1)#no shutdown Switch(config-vlan 1)#end Switch#copyrun start Configurationbuilt. Switch#

For more detailed documentation, visit us online at www.adtran.com

Quick Start Guide, 61200500L1-13B, November 2003

TechnicalSupport 1-888-4ADTRAN (1-888-423-8726)

Quick Start Guide

CONFIGURE YOUR APPLICATION

Two configuration methods are available for your NetVanta Switch:

• Web-Based GUI

•AOSCLI Once the IP address is configured (as described in the previous steps), you may

access the web-based GUI from any web browser on your network by following these steps:

1. Connect the switch to your network using any of the 24 Ethernet ports on the front of the unit.

2. Enter the IP address in your browser address line (see example, below).

3. You will then be prompted for the username and password (the default settings are admin and password).

INSTALLING THE NETVANTA 1224 (1224ST) SWI TCH P/N 1200500L1/1200504L1

4. The initial GUI screen appears.

The web-based GUI lets you configure the main switch settings and provides online guidance and explanations for eachsetting. However, use of the AOS CLI may be necessary for more advanced configurations. Access the CLI via the console port or a telnet session. For more details on CLI access, refer to the

AOS Command Reference Guide on your ADTRAN OS System Documentation CD (included in shipment).