ADTRAN 1000 User Manual

Total Access® 1000 DSLAM Dual T1/E1 LIU

T1/E1 LIU

1179010L1

LOOP 1

LOOP 2

Installation and Maintenance

CONTENTS

1. GENERAL .................................................................... 1

2. INSTALLATION .......................................................... 2

3. TESTING ...................................................................... 3

4. MAINTENANCE ......................................................... 3

5. SPECIFICATIONS ....................................................... 3

6. WARRANTY AND CUSTOMER SERVICE ............... 4

FIGURES

Figure 1. Total Access 1000 DSLAM DUAL

T1/E1 LIU ......................................................... 1

Figure 2. Total Access 1000 DSLAM DUAL T1/E1

LIU Menu Tree .................................................. 3

TABLES

Table 1. Compliance Codes ............................................. 2

Table 2. Front Panel Indicators........................................ 3

Table 3. Specifications .................................................... 3

Section 61179010L1-5A

Issue 1, November 2002

CLEI Code: VACJC90C_ _

1. GENERAL

This section provides installation and maintenance information for the ADTRAN Total Access 1000 DSLAM Dual T1/E1 LIU. Figure 1 is an illustration of the unit.

Revision History

This is the initial release of this document. Future revisions to this document will be explained in this subsection.

Features

The basic features of the Total Access 1000 DSLAM Dual T1/E1 LIU, List 1, P/N 1179010L1 include the following:

• Terminates up to two T1/E1 lines providing an interface to the network.

• SF and ESF data framing formats. (T1)

• B8ZS line code format. (T1)

• Local, payload and network loopbacks.

• Front panel indicators showing the status of the unit.

• FAS and FAS+CRC framing. (E1)

• HDB3 line code. (E1)

Figure 1. Total Access 1000 DSLAM

Dual T1/E1 LIU

General Description

The ADTRAN Total Access 1000 DSLAM Dual T1/ E1 LIU is a common card plug-in for the ADTRAN Total Access 1000 DSLAM. It connects the Data Access Terminal to a T1/E1 line. All data formatting and line encoding as well as backplane timing and control are performed by the Total Access 1000 DSLAM Dual T1/E1 LIU.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by ADTRAN could void the user’s authority to operate this equipment.

61179010L1-5A

Trademarks: Any brand names and product names included in this document are

trademarks, registered trademarks, or trade names of their respective holders.

2. INSTALLATION

C A U T I O N !

SUBJECT TO ELECTROSTATIC DAMAGE

OR DECREASE IN RELIABILITY.

HANDLING PRECAUTIONS REQUIRED.

After unpacking the unit, inspect it for damage. If damage is noted, file a claim with the carrier, and then contact ADTRAN. Refer to Warranty and Customer Service.

The Total Access 1000 DSLAM Dual T1/E1 LIU, List 1, plugs directly into the ADTRAN Total Access 1000 Data Access Terminal. No installation wiring is required.

The Total Access 1000 DSLAM Dual T1/E1 LIU should be installed in the Total Access 1000 Data Access Terminal channel bank in the slot labeled LIU. When installing the T1/E1 LIU in the Total Access 1000, grasp the unit by the front panel and push the unit into the connector until the unit is fully seated. Lock the unit into position.

Compliance Codes

This product is intended to be installed in a Total Access 1000 Chassis providing a Type “B” or “E” enclosure, with Restricted Access. Table 1 shows the Compliance Codes for the Total Access 1000 LIU.

Electronic Provisioning

The craft interfaces on the Total Access 1000 ATM BCU are used to change default options and obtain access module status through menu screens. To access the menu screens, connect a VT100 terminal or computer running a terminal emulation program to the front panel craft interface ADMIN port using a standard male-to-male RS-232 DB-9 cable. Craft port settings are as follows:

• 9600 Baud (default) (changeable to 19200 or 38400 in menus)

• No parity

• 8 Data bits

• 1 Stop bit

Windows HyperTerminal

Windows HyperTerminal can be used as a VT100 terminal emulation program. Open HyperTerminal by selecting PROGRAMS/ACCESSORIES/ HYPERTERMINAL. Refer to the Help section of HyperTerminal for additional questions.

NOTE

To ensure proper display background, select VT100 terminal emulation under SETTINGS.

Table 1. Compliance Codes

Code Input Output

Power Code (PC) C C Telecommunication Code (TC) X – Installation Code (IC) A –

Provisioning Options

All options on the T1/E1 LIU are provisionable electronically using the craft interface on the ATM BCU (Bank Controller Unit). See Figure 2.

Password

The ATM BCU will display the log on screen, and a valid user ID and password are required to access menus. The factory default is ADMIN for the account administrator, and PASSWORD for the password.

Menu Navigation

To traverse through the menus, select the desired entry and press ENTER. To work backward in the menu press the ESC (escape) key.

61179010L1-5A

+ 2 hidden pages