ADS-TEC VMT7010, VMT7012, VMT7015 User Manual

User Manual

Terminals

VMT7010/VMT7012/VMT7015

Version 1.1

VMT7010/VMT7012/VMT7015 1

Table of Contents

1 Notes 3

1.1 Relevant device documentation 3

1.2 Explanation of used symbols 3

1.3 Data, figures and modifications 4

1.4 Trademarks 4

1.5 Copyright 4

1.6 Environmental conditions 5

1.7 EC-Directives and Standards 6

1.8 Scope of delivery 7

1.9 Device features 8

2 Operating and safety instructions 10

2.1 Operating location 10

2.2 Damage due to improper use 11

2.3 Warranty / repairs 11

2.4 Treatment and disposal of lithium batteries 11

2.5 Safety instructions 12

3 Assembly 13

3.1 External Device Dimensions VMT7010 13

3.2 External Device Dimensions VMT7012 14

3.3 External Device Dimensions VMT7015 15

4 Putting into operation 16

4.1 Check for operational readiness 16

4.2 Available interfaces 17

4.3 Order of steps during commissioning 19

5 Operation 20

5.1 Front Panel Operation Keys 20

5.2 Soft keyboard 21

5.3 Touch screen 22

5.4 Status displays 23

5.5 RFID reader (as an option) 24

5.6 RFID configuration 25

5.6.1 MIFARE 25

5.6.2 LEGIC 26

5.7 ComInput configuration 27

VMT7010/VMT7012/VMT7015 2

6 Interfaces 28

6.1 24V / 48V DC power supply 28

6.1.1 Release contact (IGN) 29

6.2 Autostart function 30

6.3 Speakers 31

6.4 USB connections 32

6.5 Network connection (RJ45) 33

6.6 WLAN wireless card (optional) 34

6.7 Bluetooth wireless card (optional) 35

6.8 Serial interface COM1 (RS232) 36

7 Drives 37

8 Software & driver installation 38

8.1 Configuration Center 40

8.1.1 Automatic brightness adaptation 41

8.1.2 COM input configuration 42

8.1.3 Ignition Key Locking 42

8.1.4 USB lock 43

8.1.5 ON / OFF pushbutton configuration 44

8.1.6 RFID sample application 45

8.1.7 Soft keyboard 45

8.1.8 Screen Mop 46

8.1.9 Soft keyboard 46

9 Technical details 47

10 Service & support 48

10.1 ads-tec support 48

10.2 Company address 48

11 Declaration of EC-Conformity 49

VMT7010/VMT7012/VMT7015 3

Information:

We would recommend to make use of our website contents (www.ads-tec.de) in order to use current data and to be quickly and comprehensively informed of any technical modification.

DANGER

Indicates an imminent danger. If not avoided, death or severe injury will result.

WARNING

Indicates a possible danger. If not avoided, death or severe injury could result.

CAUTION

Indicates a possible danger. If not avoided, light or minor injuries could result.

ATTENTION

Indicates a possibly damaging situation. If not avoided, the system or something in its surroundings could be damaged.

Information:

The symbol "Information" indicates notes, terms and/or conditions that strictly need to be observed to ensure optimised and/or zero-defect operation. Tips and suggestions for the efficient use of the device and software optimisation are also provided.

1 Notes

1.1 Relevant device documentation

The following documents are decisive to unit setup and operation: User manual (this documentation): Contains information for installation, commissioning and operation of the device along with technical

data of the device hardware. Website You can download drivers, software, user manuals, leaflets and flyers from the Download section of our

website www.ads-tec.de.

1.2 Explanation of used symbols

VMT7010/VMT7012/VMT7015 4

1.3 Data, figures and modifications

All data, text and figures were prepared to the best of our knowledge. They do not represent any assurance for the properties themselves. Despite taking utmost care, no liability can be assumed for accuracy, completeness and actuality of the information. Subject to changes.

1.4 Trademarks

It is noted that any software and/or hardware trademarks and any company brand names mentioned in this documentation are all subject to the general trademark protection rights. StoraXe® and Big-LinX® are registered trademarks of ads-tec. All other third-party trademarks used are hereby acknowledged. In the case of infringement of trademark rights, ads-tec reserves the right to exercise all rights.

1.5 Copyright

This instruction manual is protected by copyright. For the authorised user, simple usage rights are granted within the scope of the intent of the contract. Any modified use or exploitation of the provided content, particularly duplication, modification or publishing in whatever form is permitted only with the prior consent of ads-tec.

In the case of copyright infringement, ads-tec reserves the right to exercise all rights.

VMT7010/VMT7012/VMT7015 5

 Temperature for devices without a heater

in operation* -20 ... 55°C for storage -30 ... 60°C

 Temperature for devices including a heater

in operation* -30 ... 55°C for storage -30 ... 60°C

 Humidity

In operation 10 … 85% without condensate For storage 10 … 85% without condensate

This unit is compliant to the DIN EN 60068-2-29 (shock and bump) testing specification

 Vibration and shock resistance

EN 60721-3-5 (06.1998), class 5M2 for HDD version, class 5M3 (terrestrial vehicles) for SSD version, 5 hours of noise-type vibrations; 3.6 g rms and 30 g peak value

Additionally applies MIL-STD 810F (01.2000), annex C, figure 514.5C (US highway truck transportation)

*(depending on mass storage device)

1.6 Environmental conditions

The device can be put into operation and used under the following conditions. Failure to observe any one of these conditions will invalidate the warranty. ads-tec cannot be held liable for any damages arising from improper use and handling.

VMT7010/VMT7012/VMT7015 6

EC-Directives

This device is compliant with the provisions and safety objectives of the following EU directives:

 1999/5/EC, R&TTE-Directive (RTTE)  2004/108/EC, EMV-Directive(EMC)

Standards

For verification and compliance with these guidelines, the following harmonized standards have been applied:

 EN 55022  EN 55024  EN 61000-6-2  EN 61000-6-4  EN 60950-1

For verification against environmental influences, the following standards are complied:

 EN 60068-2-6 (vibration test, sinusoidal)  EN 60068-2-27 (shock test)

Information:

For full compliance with the EMC legislation, the connected components and

the cable connections must also meet these requirements. Therefore shielded data cables with shielded plugs have to be used and installed according to the instructions in the operating manual.

Information:

By using the EC conformity declaration in this document, you can find detailed information about the standards applicable to this device.

1.7 EC-Directives and Standards

VMT7010/VMT7012/VMT7015 7

 1 x device  1 x 4-pin plug for power supply  Quick Start Guide

Optional scope of delivery:

 Operating system (license / opt. DVD*)  Installation kit  Power adapter

* depending on operating system

1.8 Scope of delivery

Please check that all of the following components are contained in the packaging:

VMT7010/VMT7012/VMT7015 8

No.

Description

1

Display with touch function

2

Front buttons

3

WLAN antennas (optional)

4

Front USB

5

Power-ON button

1.9 Device features

Front side

Fig. 1:

VMT7010/VMT7012/VMT7015 9

No.

Description

6

Service slot

7

Mounting bracket (optional)

8

Cover for third WLAN antenna

9

Mounting point for brackets

Rear side

Fig. 2:

VMT7010/VMT7012/VMT7015 10

General information

 All users must read this manual and have access to it at all times.  Assembly, commissioning and operation may only be performed by qualified

and trained personnel.

 The safety notices and the manual itself must be observed by all persons who

work with this device.

 At the installation site the valid guidelines and regulations for accident

prevention must be observed.

 The manual contains the most important instructions on how to use this device

in a safe way.

 Appropriate storage, proper transport, installation and commissioning, as well as

careful operation are prerequisites for ensuring safe and proper operation of the device.

 The device can be cleaned by using a soft cloth and a commercially available

glass cleaning agent (e.g. Sidolin) with low alcohol content.

ATTENTION

To prevent damage to the device, all cable lines (power supply, interface cables) must be only be connected while the device is switched off.

ATTENTION

The device may only be switched on after acclimatising to the ambient temperature in order to avoid condensate accumulation.

To avoid overheating in operation: The device must not be exposed to direct radiation by sunlight or any other heat source.

2 Operating and safety instructions

The device operates under electrical voltage and contains highly sensitive components. Intervention by the user is required only for connecting the power supply lines. Should any further modifications be required, it is necessary to consult either with the manufacturer directly or with service personnel authorised by the manufacturer. The device must be de-energised during work. Appropriate measures must be taken to prevent electrostatic discharges on components. If the device is opened up by an unauthorised person, the user may be subject to hazards and the warranty is invalidated.

2.1 Operating location

The VMT control system is designed for use on support arm systems, wall and table mounting or on moving transport equipment (commissioning trolleys, forklifts or similar). You have to take care that the environmental conditions specified in the technical data are met. Use in non-specified environments, i.e., on board ships, in explosive atmospheres or at extreme elevations, is prohibited.

VMT7010/VMT7012/VMT7015 11

Information:

The more the battery is exposed to higher temperatures, the faster it ages.

ATTENTION

Danger of explosion if using incorrect battery types.

ATTENTION

Danger of explosion if using incorrect battery types.

ATTENTION

Lithium batteries should not be exposed to fire, soldered, recharged, opened, short-circuited, reversed or heated above 100 °C and they should be disposed of properly as well as protected against sunlight, moisture and condensation.

2.2 Damage due to improper use

Should the control system have evident signs of damages caused, e.g., by improper operation or storage conditions or due to improper use or handling, the device must be shut down immediately. Ensure that it is secured against being started up accidentally.

2.3 Warranty / repairs

During the device warranty period, any repairs must only be performed by the manufacturer or by service personnel that has been authorised by the manufacturer.

2.4 Treatment and disposal of lithium batteries

This device contains a lithium battery for supplying the system clock with power as long as the supply voltage is not connected. The battery has a life cycle of 3 - 5 years depending on which load is applied.

Lithium batteries may only be replaced by the same type, or by a type recommended by the manufacturer. The used lithium battery should be disposed of in accordance with local legal regulations.

VMT7010/VMT7012/VMT7015 12

ATTENTION

All installation work performed on the device must be performed only under safe, secure and deenergised conditions. The provisions of DIN VDE 0105 apply

Information:

Always adhere to the safety measures applicable when handling components at risk of being damaged by electrostatic discharges. The provisions of DIN EN 61340-5-1 / DIN EN 61340-5-2 apply

2.5 Safety instructions

VMT7010/VMT7012/VMT7015 13

3 Assembly

3.1 External Device Dimensions VMT7010

Fig. 3:

VMT7010/VMT7012/VMT7015 14

3.2 External Device Dimensions VMT7012

Fig. 4:

VMT7010/VMT7012/VMT7015 15

3.3 External Device Dimensions VMT7015

Fig. 5:

ADS-TEC VMT7010, VMT7012, VMT7015 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual