ADS Environmental Services QR 775020 A0 User Manual
ADS® Eureka Digital System User
Manual
October 2009 QR 775020 A0
ADS LLC
4940 Research Drive
Huntsville, AL 35805
Telephone (256) 430-3366 / Fax (256) 430-6633
www.adsenv.com
ADS Eureka Digital System User Manual
Copyright © 2009 ADS® LLC. All rights reserved.
ADS® is a registered trademark of ADS LLC.
Microsoft®, Windows®, and Internet Explorer® are registered trademarks of
Microsoft Corporation.
Intel® and Centrino® are registered trademarks of Intel Corporation.
All other brand and product names are trademarks or registered trademarks of
their respective holders.
Notice of Proprietary Information
The information contained herein represents the latest information available at
the time of publication. ADS reserves the right to make any changes or
modifications to the content of this document, without notice, to reflect the
latest changes to the equipment. No part of this document may be reproduced
in any form without the written consent of ADS.
ii
ADS Eureka Digital System User Manual
Table of Contents
Chapter 1 Introduction ......................................................................1
System Features...........................................................................................3
Transmitters ...........................................................................................3
Automatic Velocity Measurement.........................................................3
In-Case Battery Charging ......................................................................3
Advanced Analysis Software.................................................................3
System Components and Options..........................................................4
Optional Equipment and Software.........................................................4
ADS No-Hassle Warranty and Return Policy..............................................5
New Product Warranty ..........................................................................5
Replacement or Loaner Equipment .......................................................5
Shipping.................................................................................................5
Product Returns......................................................................................5
Chapter 2 Principles of Leak Noise Correlation..............................7
Methods for Locating Leaks........................................................................8
Sensor Position...........................................................................................10
Leak Beyond the Sensors.....................................................................10
Leak on Connecting Pipe.....................................................................10
Chapter 3 System Components......................................................11
Descriptions ...............................................................................................12
Transmitter...........................................................................................12
Accelerometers ....................................................................................14
Receiver Unit.......................................................................................15
Headphones..........................................................................................15
Magnetic Antenna................................................................................15
Car Charge Cable.................................................................................16
Mains Charger......................................................................................16
Transmitter Y-Cable ............................................................................16
Receiver USB Cable............................................................................16
Transport Case.....................................................................................16
Software CD.........................................................................................16
Small Tablet Computer (optional).......................................................17
Ruggedized Tablet Computer (optional).............................................17
Chapter 4 Getting Started ...............................................................19
Hardware and Software Setup ...................................................................20
Software and Hardware Requirements ................................................20
Software Installation............................................................................20
Power Management .............................................................................20
iii
ADS Eureka Digital System User Manual
Chapter 5 Eureka Digital Software .................................................21
Splash Screen.............................................................................................22
Main Screen...............................................................................................23
Main Menu.................................................................................................24
File Menu.............................................................................................24
Run Menu.............................................................................................27
View Menu...........................................................................................28
Delayed Recording Menu....................................................................30
Correlation Mode Menu.......................................................................33
Help Menu ...........................................................................................33
Toolbar Buttons .........................................................................................34
Display Area ..............................................................................................35
Correlation Display..............................................................................35
Zoom/Peak Noise Suppression............................................................35
Buttons.................................................................................................36
Pipe Display.........................................................................................37
Spectrum Display.................................................................................37
Tracker.................................................................................................38
Control Area...............................................................................................40
Pipe ......................................................................................................40
Quick Start...........................................................................................41
Filters ...................................................................................................46
Sound ...................................................................................................48
Chapter 6 Deployment.....................................................................50
Choosing the Transducer Type..................................................................51
Attaching the Transducers .........................................................................52
Accelerometers ....................................................................................52
Hydrophones........................................................................................52
Setting up the Transmitters........................................................................54
Setting up the Receiver Unit......................................................................55
Radio Range...............................................................................................56
Inter-Transducer Distance..........................................................................57
Velocity......................................................................................................58
Filter Settings.............................................................................................59
Chapter 7 Index…….........................................................................60
iv
C H A P T E R 1
Introduction
The ADS® Eureka Digital System is the latest model in the proven Eureka
family of high-performance leak noise correlators designed for locating
leaks in buried water pipes. Combining advanced technology, operational
flexibility, and simplicity, Eureka Digital offers a comprehensive solution
for leak location, even under conditions ranging from substantial
background noise to minimal leak noise. This system is effective on
metallic, plastic, and cement pipes.
The Eureka Digital provides the following benefits:
ADS Eureka Digital System User Manual
Optimum performance under difficult leak detection conditions
Operation not limited by radio range
Digitally recorded sound for repetitive analysis
Optional direct transmitter connection to pipe (street-work
friendly)
Three-sensor input for automatic velocity measurement
Flexible operation
Eureka Digital uses the same technology as the successful Enigma® multipoint correlation system, a system that has demonstrated outstanding
performance in leak location.
The system offers two methods for determining the leak position: 2transducer and 3-transducer. The 2-transducer method involves
positioning the red and blue sensors at either side of the suspected leak
position. The system then measures the amount of time required for the
leak sound to reach the respective sensors. The Eureka Digital then
determines the leak position based on the known velocity of sound and
distance between the sensors.
1
ADS Eureka Digital System User Manual
2-Transducer Method
The 3-transducer method incorporates a third (yellow) sensor for
measuring velocity. Employing this option increases the accuracy of
locating the leak position.
3-Transducer Method
2
System Features
The following sections describe some of the components and features
included in the ADS Eureka Digital System.
Transmitters
The transmitters offer real-time (radio) operation or delayed recording
(logging) operation, which eliminates radio range problems associated
with conventional correlators. A transmitter also includes an integrated
sensor that can connect directly to the pipe. This allows the chamber cover
to be closed, resulting in much less of a disruption to traffic.
Automatic Velocity Measurement
Every Eureka Digital can operate with three sensors without requiring a
third transmitter. The third sensor connects directly to the receiver
module. Three sensors provide the capability for measuring velocity,
improving leak location accuracy and significantly reducing the
opportunity for dry holes.
ADS Eureka Digital System User Manual
In-Case Battery Charging
The transmitter and receiver module batteries can be charged in the
transportation case from either a vehicle 12Vdc or mains supply. This
offers additional flexibility because battery charging can occur while
traveling between sites.
Advanced Analysis Software
Eureka Digital provides software tools for the following:
Spectral analysis of leak sound
Advanced correlation, coherence, and filtering
Optional manual filter control
Audible and visual inspection of leak noise
Pipe material and velocity modification following results
computation
Optional user-defined pipe materials and velocity tables
Tracker function for selecting the best portion of recorded sound to
retrieve the correlation peak
3
System Components and Options
Two accelerometers
Two digital transmitters
Digital receiver module (incorporating third signal input)
Choice of one of the following:
Small handheld computer
Ruggedized handheld computer
Software for laptop
Vehicle antenna
Headphones
Rugged carrying case (with integrated battery charging capability)
ADS Eureka Digital System User Manual
Optional Equipment and Software
Hydrophones
Correlator reference unit
Accelerometer grip attachment
Measuring wheel
4
ADS Eureka Digital System User Manual
ADS No-Hassle Warranty and Return Policy
The following sections detail the hassle-free warranty and return policy for
the ADS Eureka Digital System.
New Product Warranty
ADS will repair or replace any Eureka Digital System equipment (supplied
by ADS) that is defective in materials and/or workmanship for up to two
(2) years following the date of shipment from ADS. To make a warranty
claim, the customer should simply call ADS at (256) 430-3366 or contact
the ADS Support Center toll-free at (877) 237-9585. The ADS Client
Services Agent will assign a Return Materials Authorization (RMA) to the
customer’s claim immediately.
The customer shall return a defective unit or part to ADS for
troubleshooting and repair or replacement within 10 days with the RMA.
Replacement or Loaner Equipment
For a defective part, ADS will ship a replacement part immediately once
the customer makes an initial claim. However, if ADS does not receive
the defective part within 30 days or testing concludes that the part
experienced excessive wear and tear or abuse for the period of use, ADS
will bill the customer for the replacement part.
For a defective unit, at the customer’s request, ADS will ship a temporary
(loaner) unit to the customer at the time of the initial claim. However, if
ADS does not receive the temporary unit from the customer within 15 days
of receiving the repaired or replacement unit or testing concludes that the
unit experienced excessive wear and tear or abuse for the period of use,
ADS will bill the customer for the temporary unit.
Shipping
The customer must pay to ship defective equipment to ADS for repair or
replacement. However, ADS will incur the costs for shipping the repaired
or replacement equipment back to the customer using the same priority
shipment procured by the customer upon returning the defective
equipment to ADS.
Product Returns
If the customer is not satisfied with the performance of the Eureka Digital
System, the customer may return the equipment within 30 days for a full
5
ADS Eureka Digital System User Manual
refund, provided the condition of the equipment is in the same condition as
sold, except for expected or normal wear and tear for the period of use.
6
ADS Eureka Digital System User Manual
C H A P T E R 2
Principles of Leak Noise Correlation
Leak noise correlation is used to detect leaks in pipes with a positive
internal pressure, where leaks allow a loss of flow to the outside. The
movement of fluid through the leak causes rapid pressure changes around
the site of the leak, establishing a noise source at the leak. This noise
travels in both directions, at the same velocity, along the pipe from the
leak. These principles are used to determine the leak location.
Note: Noise is not a constant frequency, like a musical note, but a
random and constantly changing blend of different frequencies.
The correlator operates on this principle.
7
ADS Eureka Digital System User Manual
2
Methods for Locating Leaks
Previous methods of leak location relied on an initial detection of a noise,
which was then traced along ground level to identify the location of the
maximum noise. This location was assumed to be directly above the
location of the leak. The equipment used for this method included
listening sticks and stethoscopes, but these were difficult to use if the noise
proved too faint or loud for accurate location. Background noise was
another problem; electronically-filtered amplifiers were introduced in an
attempt to overcome such problems.
A correlator operates by comparing the noise detected at two different
points in the pipeline. Noise travels from the leak in both directions along
the pipeline at a constant velocity (depending on several factors).
Therefore, if the leak occurs at an equidistant location between the two
sensors, these sensors will detect the noise at the same time. Conversely,
if the leak does not occur at an equidistant location, then the sensors will
detect the same noise at different times. The correlator measures this
difference (delay) in time.
The following diagram provides an illustration of this principle:
Assume the sensors are located on the valves A and B (convenient access
points for underground pipes). However, the leak occurs closer to valve
A.
By the time a particular noise from the leak has reached A, the same noise
heading towards B has travelled only as far as X. The distance from X to
B causes a delay (t) before the noise arrives at B. Therefore, the correlator
detects the delay (t) between the arrival of the noise at A and B. Assume
the velocity of sound is V and the distance between the sensors is D. As
the distance from X to B = V * t (velocity x time), then D = (2 * L) + (V *
t). This equation may be rearranged to provide L, the distance from the
sensor closer to the leak site:
L
)*( tVD
The sound velocity can be calculated based on the pipe diameter and
material, and the distance between the sensors can be determined by
careful measurement. Therefore, the correlator can calculate and display
the location of the leak as a direct distance from the closer sensor. The
correlator also may be used to measure the actual velocity of sound in the
8
ADS Eureka Digital System User Manual
pipe under investigation, ensuring the greatest accuracy in locating the
leak.
9
Sensor Position
Correlator operation relies on the location of the leak existing between the
two sensors. However, two contexts can prevent this from occurring. The
solution requires moving one sensor before a successful correlation can be
performed.
Leak Beyond the Sensors
If the leak is located beyond the length of pipe between the sensors, the
correlator will ignore the transit time from the leak to the nearest sensor
because the transit time will be the same for both sensors. This will give
the impression that the leak exists directly at the location of the sensor
closest to the leak (occasionally referred to as out-of-bracket). This
requires that one sensor be moved to locate the leak position accurately.
ADS Eureka Digital System User Manual
D
Leak
Leak on Connecting Pipe
If the leak is occurring on a pipe that connects to the pipe being measured,
the noise will appear to spread from the connection point and, therefore,
indicate that point as the location of the leak. This requires moving one
sensor to the connecting pipe, ensuring the leak falls between the sensors,
to accurately locate the leak. A thorough knowledge of the entire pipe
network layout is essential to ensuring that the correlator is taking
measurements on the correct section of pipe and that no possibility exists
for leaks on branch pipes, causing false readings.
D1
Sensor A Sensor B
Leak position
indicated with
sensors at A and B
Sensor A
D2
True position
Sensor B
of leak
Sensor C
10
C H A P T E R 3
System Components
The standard Eureka Digital System consists of the following components:
Red transmitter (including antenna)
Blue transmitter (including antenna)
Two accelerometers
Receiver unit (includes antenna and receiver belt pouch)
Headphones
ADS Eureka Digital System User Manual
Magnetic vehicle mount antenna
Car charge cable
Mains charger
Transmitter programming Y-cable
Receiver unit USB cable
Carrying Case
Software CD
The following options are available:
Small tablet computer
Ruggedized tablet computer
Carrying Case
11
Descriptions
The following sections provide brief descriptions of the Eureka Digital
System components.
Transmitter
The transmitters (blue and red) operate in a similar manner, and each
includes the following components:
Radio transmitter
Built-in accelerometer
Pushbutton switch
LEDs
Handle
ADS Eureka Digital System User Manual
Charge/accelerometer connector
Antenna connector
Headphone connecter
The transmitter transfers the information from the transmitter unit to the
receiver unit.
Features
Built-in Accelerometer
Each transmitter contains a built-in accelerometer located in the base of
the unit. The transmitter is attached to a pipe using the magnetic base.
When spatial or positional limitations deem it impractical to use the builtin accelerometer, the external accelerometer may be used.
12
Pushbutton switch
The pushbutton switch turns on and off the transmitter unit. Refer to
Transmitter Control and Indicators below for more information.
LEDs
The LEDs display information about the transmitter. Refer to Transmitter
Control and Indicators below for more information.
Handle
The handle exists for carrying and positioning the transmitter.
Charger/Accelerometer Connector
This connector, located on the side of the transmitter, is used for charging
the transmitter, connecting the external accelerometer, or connecting the
programming cable. The connector is angled slightly downward to divert
rain away from the connector.
Antenna Connector
ADS Eureka Digital System User Manual
The antenna connector is for connecting the standard antenna or an
external antenna, if required.
Headphone Connector
The headphone connector is for connecting the headphones to monitor
signals directly from the transducer.
Recharging the Transmitters and Battery Life
To recharge the transmitters, simply place the transmitter in the case,
connect the charging lead in the case to the transmitter, and connect the
charge lead from the car or mains to the case. A single transmitter also can
be charged directly from an appropriate charger. The charger
automatically uses boost charge and trickle charge rates to obtain optimum
use and battery life. In temperatures ranging from 32 º to 122 º Fahrenheit
(0 º to 50 º Celsius), the batteries can be fully charged (from a totally
discharged status) in approximately 2.5 hours.
The transmitter can operate for approximately 6 to 7 hours (in high-power
mode) on a full charge. In low-power mode, battery life is much longer.
Transmitter Control and Indicators
The top of each transmitter has a pushbutton switch and 7 LEDs.
One High-power radio LED
One Low-power radio LED (This is the proper setting when the
transmitter is within 66 feet (20 m) of the Receiver Unit.)
Five sound/battery LED indicators
13
LED Response While Charging
Under normal circumstances, when the charger is plugged in, the LED bar
graph will ramp up repetitively. This indicates that the battery is
undergoing a fast or top-off charge.
When the fast charge is complete and the battery is just receiving a tricklecharge, the bar graph will stop ramping up and all LEDs in the bar graph
will be off, except the top red LED. This LED will flash quickly once
every 2 seconds.
If the battery is in a very deep discharge state when the charger is plugged
in, it cannot accept a fast charge. If this occurs, only the bottom LED will
flash (on for 2 seconds/off for 2 seconds). This indicates that the charger
is pre-charging the battery at a low current to prepare the battery to receive
the fast charge. Once the pre-charge is complete, the charger will begin
the fast charge and the bar graph will begin ramping up repetitively (as
under normal conditions).
On/Off
The push button switch has various functions that are initiated by pressing
the button for a short or long time (2 seconds):
ADS Eureka Digital System User Manual
Pressing and holding for 2
seconds and then releasing
Pressing and releasing Sets the transmitter to low power, illuminating
Pressing and releasing Turns off the transmitter and all the LEDs.
Battery Test
When the transmitter is off,
press and release the button
to display the battery level.
When the transmitter is on,
press and hold the button for
more than 2 seconds to start
the battery test.
Accelerometers
Turns on the transmitter and sets the
transmitter to high power, illuminating the
High-power LED. The 5 LEDs display the
sound strength.
the Lo-power LED. The 5 LEDs display the
sound strength.
The Sound/Battery LEDs display the relative
battery charge for approximately 10 seconds.
The Sound/Battery LEDs display the relative
battery charge for approximately 10 seconds.
The accelerometers connect to the transmitters and may be used when the
location or the transmitter does not allow easy attachment to a pipe or
fitting (using the internal accelerometer). They also may be used when the
transmitter must be located aboveground for good signal performance.
14
Receiver Unit
The receiver unit receives power from the USB port of the computer and,
therefore, must be connected to the computer when in use. The unit
receives signals from the transmitters. An accelerometer also can be
connected to the receiver for a 3rd sound input into the system (designated
the yellow channel). The receiver unit uses a screw-on antenna and can be
belt-mounted and used with a laptop computer for greater flexibility.
When using the unit in a vehicle, a magnetically mounted antenna can be
used to improve signal reception from the transmitters.
ADS Eureka Digital System User Manual
The receiver unit has the following connectors and indicators (from left to
right):
Programming connector Used with the optional Y-Cable to program
Transducer connector
LED Illuminates when the unit is connected to
USB connector Used with the USB cable to connect to the
Headphones
The headphones can be connected to either transmitter to monitor the
sound picked up by the transmitter in real-time.
Receiver Unit
the transmitters
Allows for connection of an optional
transducer for 3-transducer operation
the computer. If the LED flashes, the USB
driver has an error or is not loaded.
computer. The cable powers the receiver
unit and allows for the transfer of data.
Magnetic Antenna
The magnetic antenna can be used with the receiver to increase the signal
reception (e.g., when the receiver is used in a vehicle).
15
Car Charge Cable
The car charge cable can be used to connect the case to a power supply in
a vehicle to recharge the two transmitters in the case. The cable connects
to a socket on the side of the case. The transmitters in the case must be
connected to the two charge cables in the case.
Mains Charger
The mains charge cable can be used to connect the case to an AC power
supply to recharge the two transmitters in the case. The cable connects to
a socket on the side of the case. The transmitters in the case must be
connected to the two charge cables in the case.
Transmitter Y-Cable
This cable is used to connect the receiver to the two transmitters when
programming the transmitters from a PC to record sound, instead of
transmitting sound. This can be used for recording sound after a certain
delay.
ADS Eureka Digital System User Manual
Receiver USB Cable
This cable powers the receiver and allows for the transfer of data to and
from the PC. The receiver must receive power from a USB connection to
function.
Transport Case
The transport case stores the standard equipment and provides protection
from the environment. This case can be connected to a car or mains power
source via an adaptor to charge the transmitters when they are stored in the
case. This option can be particularly useful when transporting the system
to a remote location.
Software CD
This CD contains the Eureka Digital software for loading onto a suitable
PC. Refer to Hardware and Software Setup on page 20 in Chapter 4,
Getting Started, for more information.
16
Loading...