Admiral DDB1501AWZ, DDB1501AWW, DDB1501AWB Owner’s Manual

D,shwash

Operating li

Loading ..

Dishwashe

'iiiii

_= = == = =

_=7

Care & Cleaning ............ 8

Troubleshooting ......... 9-10

Warranty & Service ........ 11

Guide d'utilisation

et d'entretien .............. 12

Gui_ de Uso y Cuidado ..... 24

Part No. 6 919419 B _2005 Maytag Appliances Sales Co.

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in this

manual are not meant to cover all possible conditions and

situations that may occur. Common sense, caution and care

must be exercised when installing, maintaining or operating

tile dishwasher. Always contact your manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words, Labels

Important Safety Instructions

Products with a .uL_)label have been listed with Underwriter's Laboratories, Inc. - those with a CSA tag have

been listed with Canadian Standards Association. Nevertheless, as with any other equipment using electricity

and moving parts, there is a potential hazard.

1. Read all instructions before using the dishwasher.

2. Use the dishwasher only for its intended function.

3. Disconnect electrical power to dishwasher before attempting to service.

4. To avoid electrical shock hazard, the sides and back must be enclosed and the front panels must be

attached before electrical power is applied to the dishwasher. Refer to the installation instructions for

proper grounding procedures.

5. Connect to a properly rated, protected and sized power supply circuit to avoid electrical overload.

6. Children should never be permitted to operate, or play in, with, or around this dishwasher.

Z Toreduce the riskof injury when loading items to be

washed, sharp or pointed items should be locatedwith

the handles up. Also, load sharp items so they are not likely to damage the door seal.

8. Do not touch the heating element on the bottom of the tub during or at the completion of a cycle. It will

be [lot.

9. Use only detergents and rinse additives designed for a residential automatic dishwasher. Never use soap,

laundry detergent, or hand washing detergent in your dishwasher. Keep these products out of reach of

children.

10. Do not sit, stand on or abuse the door or dish racks of the dishwasher.

11. Under certain conditions, hydrogen gas may be produced in a hot water system that has not been

used for two weeks or more.Hydrogen gas is explosive. If the [lot water system has not been used

for such a period, turn on all hot water faucets and let the water flow from each for several minutes. This will

release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during

this process.

12. Do not wash plastic items unless marked "dishwasher safe" or the equivalent. For plastic items not so

marked, check the manufacturer's recommendations.

13. Do not tamper with controls.

14. To prevent accidental child entrapment and suffocation risks, always remove the door to the

washing compartment when removing an old

dishwasher from service or discarding it.

15. Use caution when unloading the dishwasher. Dishes

will be [lot if unloaded shortly after a cycle has

completed.

16. Certified residential dishwashers are not intended for licensed food establishments.

1Z To avoid water, mold or mildew damage to your home,

inlet and drain hose connections should be checked periodically for leaks.

Save These Instructions

for Future Reference

WhatCanandCannotBeWashed

Most tableware, cookware and flatware can safely be washed in your dishwasher. Check with the manufacturer.

_ATE_i_ _|_WA_ER _E_

Aluminum Yes, except anodized. High water temperature and detergents may affect finish.

Cast Iron No Seasoning will be removed, and iron will rust.

China/Stoneware hand-painted. Antique, hand-painted or over-the-glaze patterns may fade. Gold leaf

Crystal Yes, except antique or Always check manufacturer's recommendation before washing. Some

Filters Not recommended. May leave a dingy deposit or stain on dishwasher interior.

Glass Yes A specialty glass called milk glass can yellow with repeated dishwasher

Gold-Plated Flatware No Will discolor.

Pewter, Tin No

Plastics disposable plastic vary in their capacity to withstand high water temperatures and

Stainless Steel Yes Run a Rinse Only cycle (select models) if not washing immediately.

Sterling Silver or No, if has commercial Always check manufacturer's recommendation before washing. Run a

Silverplate "darkening". Rinse Only cycle (select models) if not washing immediately. Prolonged

Wooden Items No Wood maywarp, crack or discolor.

Yes, except antique or Always check manufacturer's recommendation before washing.

may discolor.

delicate crystal, types of leaded crystal may etch with repeated washings.

washing.

Yes, top rack, except Always check manufacturer's recommendationbefore washing. Plastics

items, detergents. Disposable plastic itemsare not dishwasher safe for this

reason.

Prolonged contact with foods containing salt, vinegar, milk products or

juice could damage finish.

contact with food containing salt, acid or sulfide (eggs, mayonnaise and seafood) could damage finish. Commercial "darkening" may be

removed by detergent.

Opemin9Tips

Before You Start

• Don't prerinse. Simply scrape off any bones or

large food particles.

• If connected to a food waste disposer, make certain

the disposer is empty before starting the dishwasher.

• Scrape off tomato-based food soils (see page 8).

• Remove certain foods such as mustard, mayonnaise, lemon juice, vinegar, salt or dressings

from stainless steel flatware as soon as possible. These foods may cause rusting and pitting if allowed

to remain in contact with the surface for an extended

period of time.

Starting the Dishwasher

1. After loading the dishwasher and adding detergent, select the desired cycle by pressing the cycle select pad until the light next to the desired cycle

is illuminated. Choose the desired options by

pressing the pads. The indicator lights for the selected cycle and options will illuminate. To cancel an option press the pad again.

2. To start a cycle, close the door until it latches then press the START/Cancel pad once. After a pause,

the fill will begin. The display countdown (select

models) will flash until START/Cancel is pressed.

To cancel a running cycle, press the START/Cancel

pad once. The dishwasher will drain, then shut off. To turn the dishwasher off without draining, press the START/Cancel pad twice. To prevent

unplanned cycle or option changes, these selections

are "locked in" after 1 minute.

Note

• If the cycle select pad is pressed after the controls have been "locked in", the light beside the selected cycle will flash three times.

Adding a Forgotten Item

For best cleaning, the forgotten item should be added

early in the cycle.

1. Grasp door handle and unlatch door without opening completely. All lights will flash to indicate

that the cycle is suspended.

2. Wait for the water circulation to stop.

3. Open the door and add the item.

4. Close and latch the door. Lights will stop flashing when the door is properly shut. After a slight delay, the cycle resumes automatically at the point of

interruption.

Notes

Note

• If START/Cancel is not pressed within 30 seconds of choosing your cycle, the dishwasher

will turn off.

The dishwasher remembers your last cycle so you do not have to reset the cycle each time. To start the dishwasher using the same cycle and options selected on the previous wash, just press the START/Cancel pad.

• If the door is opened during a running cycle, there may be up to a 30 second delay before the

dishwasher restarts after closing the door.

• Extended interruption of the wash cycle is not

recommended.

General Recommendations

[Rack features vary by model)

• Items can be centered behind a single tine or loaded at an angle to maximize space.

• Avoid blocking or preventing the spray arms from

spinning freely. Do not allow items to extend beyond the racks.

• Face soiled surfaces toward the center of the dishwasher.

For best dishwashing results follow these guidelines to determine the best arrangement for your items.

10 Place Setting Load

[Rack features vary by model)

To remove the basket(s) from the door:

1. Grasp the utensil basket by the handle. Slide it toward

the top of the door.

2. Lift the basket off the securing knobs.

To replace the basket(s) in the door:

1. Align the slots on the backside of the utensil

basket with securing knobs on the door.

2. Set the utensil basket on the securing knobs.

3. Slide the basket toward the bottom of the door until it locks into place.

Removing the Upper Rack

The rack can be removed when tall or oversized items

need to be loaded into the lower rack. Unload the rack before removing it from the dishwasher.

To remove rack with tab-lock rack stops:

Upper Rack

Lower Rack

Upper Rack

Glasses, cups, stemware, light-weight plastics, plates, bowls, pans, long-handled utensils etc. can be loaded in this rack. Do not load glasses over the tines.

Lower Rack

A variety of items such as dinner plates, mixing bowls, pots and pans and baking dishes can be loaded in this

rack. Wider items can be placed along the left side and

back of this rack.

Utensil Baskets

Removable Door Utensil Baskets

For best cleaning results, prevent items from nesting together by placing some items in the baskets with handles up and some with

handles down. Load knives handles up and spoons and forks

handles down.

Roll the rack '/3to '/_of the way out.

Locate the rack stops at the end of each track. Squeeze the tab in the middle of the rack stop and pull the rack stop straight out. Take care to support

the rack while removing the rack stops.

3. Roll the rack all the

way out of the track

and remove from the dishwasher.

To replace:

1. Replace the dishwasher rack by Stylemay

guiding the wheels varybymodel into the tracks.

2. Push each rack stop squarely into the end of the track until the catch pops into the small hole on the

side of the track.

Important:

The dishwasher will not operate correctly if the

wash arm is not aligned with one of the water inlet

holes on back wall of the dishwasher.

Rack

Stop

DishwasherUse

Hot Water

For optimal cleaning and drying results, hot water is necessary. The incoming water temperature

should be 120 ° F [49 ° C) to properly activate the detergent and melt greasy food soils.

To check the incoming water temperature, turn on the

hot water faucet nearest the dishwasher and let it run _._.. ....

into a glass in the sink. Place a candy thermometer in _ T_ the glass and check the temperature once it has stopped rising. PRE

U t y tne'er-en" " ...............

Use a detergent designed specifically for use in an

automatic dishwasher. Be sure it is fresh. Store

granular detergent in a cool, dry place (not under the

sink).

Recommended Amount

Too little detergent results in poor cleaning, hard water filming/spotting and poor drying. Too much detergent

can cause permanent etching/cloudiness. Suds can cause the dishwasher to overflow. Measure

the detergent carefully and use only detergents

designed for use in a dishwasher. Less detergent is

needed in soft water. Try another brand of detergent if sudsing continues.

The amount of detergent to use is determined by the

hardness of the water and soil level of the load. Refer to the following chart for detergent usage

recommendations.

Light Soil 2 tsp 6 tsp

Soft (0-4 gpg) Normal Soil /4tsp 6 tsp

Heavy Soil 4 tsp 7 tsp

Light Soil /4tsp 6 tsp

Medium (5-9 gpg) Normal Soil 4 tsp 6 tsp

Heavy Soil 5 tsp 7 tsp

Hard (10-12 gpg) All Levels 5 tsp 8 tsp

*Your local water utility or state university extension service can tell

you the degree of water hardness in your area.

In extremely hard water conditions (13 grains per gallon or more*), it is difficult to achieve good

results with any dishwasher. A mechanical water

softener may be necessary to improve water quality, detergent effectiveness, and protect the dishwasher parts from the damage that hard

water can cause.

Add recommended amount of detergent to each cup

as shown and close the detergent lid.

WASH

Do not use detergent with the Rinse Only (select models) cycle. Leave the detergent lid open when running Rinse Only (select models).

Rinse Aid

Regular use of a rinse aid improves drying, reduces spotting and filming, and reduces

moisture left on the dishwasher interior.

An automatic rinse aid dispenser is located next to the

detergent cup.

The window next to the dispenser cap indicates when the rinse aid reservoir needs to be refilled. When the

level of rinse aid is below the indicator marks and the

window is nearly clear, it is time to refill the dispenser.

Check the dispenser monthly.

To add rinse aid to the

dispenser, turn the cap counterclockwise to open.

Remove the cap and pour liquid rinse aid into the @

opening. The amount of rinse aid dispensed during

the cycle is adjustable by moving the lever inside the

reservoir area. For most water conditions use the manufacturer recommended setting of "2". Adjust it up to

the "MAX" setting for hard water. Set the lever anywhere

between these amounts as needed to get the best results. Replace the cap and turn it clockwise to close.

FUJI

Cycles,OptionsnndLights

Cycles

Choose the cycle that best describes your dishload by pressing the cycle select pad. (See page 3, Operating

Tips, for how to begin the cycle).

Heavy Wash Long cycle for heavy food soils. 132" 2 washes/3 rinses

Normal Wash

Light/Quick Wash

Rinse Only

(select models)

Includes approximately 30 minutes of dry time.

**Number of fills will vary depending on the soil level of each load.

Note

Depending on water temperature, there may be time added to the cycle to bring water up to temperature.

Medium cycle for average food soils. The turbidity sensor is active with this cycle.

Short cycle for light food soils. Rinses dishes being held until there

is a full load.

97-117"

82*

1-2 washes**/1-2 rinses**

1 wash/2 rinses

1 rinse

Options

In addition to choosing a cycle, choose as many available options as are needed for your dishload.

Hi TempWash provides additional heat during the wash portion of the cycle, All cycles

Hi Temp Wash which ensures proper water temperature for better cleaning and drying results. (except Rinse Only

Heated Dry surfaces may be necessary and more moisture may be noticed adhering (except Rinse Only

Belay Used to automatically start the cycle at a later time. See page 7 All cycles

It also adds an additional rinse to the cycle which improves results in hard [select models]) water situations.

For enhanced drying results select this option. When Heated Dry is not

selected, towel drying of some items such as plastic and items with non-stick All cycles

to the dishwasher interior. In models with plastic interiors, it is normal to [select models]) notice vapor escaping from the door vent as the heat dries your dishes. Vapor will escape even if Heated Dry is not selected.

for instructions.

Cycles,OptionsnndLights

Delay

The Delay option can be used to automatically start the cycle at a later time to reduce daytime heat

buildup in the home or to take advantage of reduced

energy costs if available in your area. This option is

also useful for conserving hot water at times of high

household usage (showers, laundry). To set up a Delay:

1. Select the appropriate cycle and options for the load. Close the door.

2. Press the Delay pad until the desired amount of delay time is selected.

3. The Delay indicator and the count down display (select models) will flash until the START/Cancel

pad is pressed.

4. As soon as the START/Cancel pad is pressed, the

flashing will stop and the delay time will begin

counting down. The Delay indicator will remain lit until the delay time has counted down.

5. The cycle will automatically start as soon as the delay time expires.

Note

• If 30 seconds elapse between setting the cycle and options and pressing the START/Cancel pad, the dishwasher will turn off.

To cancel a Delay: When the delay is counting down, press the Delay pad

again. The indicator light will go out and the cycle will

start or resume immediately.

To cancel a Delay and the cycle:

• Press START/Cancel once to drain and turn off the dishwasher.

• Press START/Cancel twice to turn dishwasher off

without draining.

Lights

ON Illuminates during all rinse, wash and dry portions of the cycles.

CareandCleaning

General Recommendations

• The dishwasher interior is normally self-cleaning. Periodically check the bottom of the dishwasher tub to see if any large particles remain.

• Wipe the edge of the inner door liner to remove any food soil splashes which occurred during loading.

• When cleaning stainless steel, always wipe with the grain. Never use products containing chlorine bleach or citric acid.

Standard Exterior

Stainless Steel

Exterior

(select models)

Interior Light to moderate

*Brand names are trademarks of the respective manufacturer. **Call 1-877-232-6771 to order.

Light to moderate

Daily cleaning and light soil

Moderate to heavy soil

Streaks or fingerprints/restore shine Discoloration

Discoloration, or tomato-based stain

• The color from some tomato-based food soils may occasionally adhere to various components of the dishwasher interior, causing temporary discoloration.

To minimize this:

• Remove excess tomato-based food soils from dishes,

before loading.

• Run the Heavy Wash cycle when washing loads containing tomato-based food soils.

• Use a dishwasher detergent that contains chlorine to

better fight staining.

Soft damp cloth and liquid spray cleaner. Do Not use abrasive powders or cleaning pads.

Soft cloth or sponge and one of the following:

• Mild detergent and water

• A solution of white vinegar and water

• Formula 409 Glass and Surface Cleaner*, or similar multi-surface cleaner.

• Do Not use products containing chlorine

bleach or citric acid.

Follow with rinse and dry.

Soft cloth or damp sponge and Bon Ami*.

Follow with rinse and dry. Soft cloth and Stainless Steel Magic Spray**. Soft cloth or damp sponge and Cameo Stainless

Steel Cleaner*. Rinse immediately and dry. Soft cloth or damp sponge.

Switch dishwasher detergent to chlorine-based

product.

Storage/Moving

Fill detergent cup with a fresh-scented dishwasher detergent or baking soda and select the Normal Wash cycle. Allow the dishwasher to complete the cycle. Then turn the water supply off and drain the dishwasher. To drain, press the START/Cancel pad once to activate the dishwasher. Press START/Cancel again to activate

the drain. Operate the drain twice to ensure most of the water is removed. Last, disconnect the electrical

supply and prop open the door.

When turning the water supply to the home off, the water shut off at the dishwasher must be turned off also.

Troubleshooting

CHECK THESE POINTS TO HELP SAVE YOU TIME AND MONEY.

Dishwasher will not fill • Press the START/Cancel pad to start the dishwasher

• Be sure door is latched securely.

• Be sure the water is turned on.

• Check that the pad is properly selected for a cycle.

• Check your home's circuit breaker or fuse box.

• Check inlet [lose for a kink.

• Check water valve inlet for sediment and clean if necessary.

Dishwasher will not drain/ water in tub bottom

Dishwasher adds water at • This is normal. The sensor (select models] in the pump must stay submerged so a

end of cycle short fill of water is added after the cycle's last drain.

Detergent cup is not empty • Check that the cycle is completed.

Dishwasher seems noisy "

• If hooked up to a food waste disposer, be sure the knock-out is removed from the disposer inlet.

• Check for food obstruction in the drain or disposer.

• Check drain hose for a kink.

• Check your home's circuit breaker or fuse box.

• Check that tile cycle is completed.

• Be sure dispenser is not blocked.

• Use fresh detergent stored in a cool, dry place. A water valve hiss during fill is normal.

Water circulation sounds are normal. A thumping sound may be a wash arm bumping an item that is extending beyond the

racks. Readjust load to avoid obstructing wash arm. Chopping or grinding sounds may be heard as tile internal food disposer chops [lard items like fruit seeds, nuts, etc.

Humming during tile drain is normal.

A snap noise is the detergent cup lid hitting the door liner when the dishwasher door

is opened at the end of the cycle. This is normal. Proper installation affects the noise level.

Cycle takes too long • Hi Temp Wash has been selected and the cycle is extended to heat water.

• Check to see that the incoming water temperature is 120° F (49°C].

Dishwasher has an odor •

Dishwasher leaks

*Brand names are trademarks of the res

Run dishes being held in the dishwasher through a Rinse Only cycle (select models]. Marly dishwashers [lave a "new" smell when first installed. This will dissipate with use. Dishwasher may not be draining properly. (See "Dishwasher Will Not Drain" section.] Fora strong odor, place baking soda in both sides of the detergent cup. Select

Light/Quick Wash cycle and allow the water to circulate for about 10 minutes. Interrupt the cycle by unlatching the door and let it stand overnight. Restart the

dishwasher by latching the door and allow it to complete the cycle. Another alternative

is to use a dishwasher cleaning product such as Jet-Dry Dishwasher Cleaner*.

• Check that the dishwasher is level. (Refer to the Installation Instructions.]

• Suds can cause the dishwasher to overflow. Measure the detergent carefully and use only detergents designed for use in a dishwasher. Less detergent is needed in soft

water. Tryanother brand of detergent if sudsing continues.

• Follow directions closely on how to add a forgotten item (log.3).

• Toavoid rinse aid leaking from the dispenser, be sure the lid is securely attached.

)ective manufacturer. Cont.

Troubleshooting

iiiiiii i ilil .....

Indicator lights flashing • Tile countdown display (select models) flashes after a cycle is selected until tile

START/Cancel pad is pressed.

• The countdown display (select models) and the delay indicator flash after a delay is selected until the START/Cancel pad is pressed.

• All active display indicators flash if the door is opened during a running cycle or delay.

• The currently selected cycle flashes if an attempt is made to change the cycle after cycle "lock-in".

Glasses are cloudy/ • Select Hi Temp Wash option. spotted • Check water temperature. Incomingwater should be 120° F (/49° C).

• Always use a rinseaid.

• Confirm that the cloudiness is removableby soaking the item inwhite vinegar for approximately 5 minutes. If removed,the problem isdue to hard water. Adjust detergent amount being used to match water hardness (pg. 5). Be sure detergent is fresh, stored properly and is a highquality brand.

• If cloudiness is not removable,it is etching. This is an erosion of the surface of the glassware and carl be caused by water that is too hot,from using too much detergent or by prewashing. Detergent needs food soil to act upon. If etching has occurred, the glassware is permanently damaged. Toprevent further etching, adjust the detergent amount to match the water hardness, stop prewashing, and use water heating options only when incoming

water temperature isbelow 120° F (/49° C).

Food soil remains • Check water temperature. Incomingwater should be 120° F (/49° C). on dishes • Run hot water at the sink before starting the dishwasher.

• Check water hardness and adjust detergent amount accordingly (pg. 5).

• Use fresh detergent stored in a cool dry place.

• Select proper cycle for the soil level (pg. 6).

• Make sure the upper rack wash arm connector is correctly aligned in one of the water inlet holes (jog./4).

• Load items so they do not block the wash arms (pg./4).

• Load the utensil basket with knife handles up and spoon and fork handles down.

• Do not place glasses over tines.

• Before loading, scrape off burnt on foods and wipe the starchy film from utensils used with pasta, rice and oatmeal. These soils require more energy than the rest of the load to clean.

Items washed in the • Aluminum utensils or pans can leave marks when they rub against other items. Leavea dishwasher or the slight space between items.

dishwasher tub itself • Iron deposits in the water can leave a yellow, brown or orange film on dishes or the are stained/discolored dishwasher tub. A rust filter may be needed. Check with a water treatment company.

• Separate silver or silver-plated silverware from stainless steel. These metals can be damaged by contact with each other during washing.

• Color from tomato sauces may adhere to the interior parts of the dishwasher (pg. 8). If light staining has occurred, leave the door open to oxidize the stain away. Use a dishwasher

detergent that contains chlorine to better fight staining.

• Certain dishwasher detergents may stain silver. Tryanother brand of detergent.

Items not properly • Besure Heated Dry is selected.

dried/moisture is • Water droplets may form on the inner door as part of the drying process. present on the • Use a rinse aid separate from the detergent like Jet Dry* or Cascade Rinse Aid regularly, to

dishwasher interior improve drying. Turn the rinse aid selector toward the MAX setting. after the dry cycle • Check water temperature. Incoming water should be 120° F (/49° C).

• Select Hi Temp Wash option.

• Increase detergent amount to match water hardness (pg. 5).

• Load properly. (log./4)

• Plastic and items with non-stick surfaces are difficult to dry because they have a porous surface which tends to collect water droplets. Towel drying may be necessary.

• Glasses and cups with concave bottoms hold water and require towel drying. Locate these items on the more slanted side of the rack for improved results.

Dishware is chipped • Load dishes according to instructions so they do not strike each other (pg./4).

• Washing fine antique china/crystal in the dishwasher is not recommended.

• Do not load glasses over the tines.

• Do not overload.

*Brand names are trademarks of the respective manufacturer. 10

+ 25 hidden pages