ADLINK ASD26-MT1 ET User Manual

ASD26-MT1 Series

2.5" SATA 6 Gb/s Solid State Drive

Specification

Revision: 1.0

Date: 20th Decenber 2013

Advance Technologies; Automate the World.

Document History

Revision

0.01 2013/30/05 Preliminary Release

0.02 2013/6/20 Updated IOPS

0.1 2013/8/7 Added MT1 CT series models

1.0 2013/12/20 Added MT1 EP series models

Date Changes

2 Specification

Copyright 2013 ADLINK Technology, Inc.

Disclaimer

The information in this document is subject to change without prior notice in order to improve

reliability, design, and function and does not represent a commitment on the part of the

manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental,

or consequential damages arising out of the use or inability to use the product or documentation,

even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright.

All rights are reserved. No part of this document may be reproduced by any mechanical,

electronic, or other means in any form without prior written permission of ADLINK Technology,

Inc.

Specification 3

Table of Contents

1 Introduction.......................................................................... 5

1.1 Overview...................................................................................................5

1.2 Product Specification.....................................................................................5

1.3 Functional Block Diagram ............................................................................. 12

1.4 Product Image .......................................................................................... 13

1.5 Mechanical Drawing:................................................................................... 14

1.6 Architecture.............................................................................................. 15

1.7 Hot Plug Support ....................................................................................... 15

2 Pin Locations and Signal Descriptions ................................. 16

2.1 Pin Locations............................................................................................ 16

2.2 Signal Descriptions..................................................................................... 16

3

ATA Command Sets............................................................. 18

3.1 ATA Command ......................................................................................... 18

3.2 Power Management Command Set ................................................................. 22

3.3 Security Mode Feature Set............................................................................ 23

3.4 SMART Command Set ................................................................................ 23

3.5 Host Protected Area Command Set ................................................................. 24

3.6 48-Bit Address Command Set ........................................................................ 24

3.7 Device Configuration Overlay Command Set ...................................................... 25

3.8 General Purpose log Command Set................................................................. 25

4

SATA Command Sets........................................................... 26

4.1 SATA Command........................................................................................ 26

5

References .......................................................................... 27

6

Getting Service.................................................................... 28

4 Specification

1 Introduction

1.1 Overview

The ASD26 (ASD26-MT1) series 2.5" SATA Solid State Drive (SSD) delivers leading performance in an industry
standard 2.5" form factor while simultaneously improving system responsiveness for mobile applications over
standard rotating drive media or hard disk drives. By combining leading NAND flash memory technology with
our innovative high performance firmware, ADLINK delivers a SSD for native Serial Advanced Technology
Attachment (SATA) hard disk drive drop-in replacement with enhanced performance, reliability, ruggedness and
power savings. Since there are no rotating platters, moving heads, fragile actuators, or unnecessary delays due
to spin-up time or positional seek time that can slow down the storage subsystem, significant I/O and
throughput performance improvement is achieved as compared to rotating media or hard disk drives. This
document describes the specifications of the ASD26 series 2.5" SATA SSD in 2.5" form factors.

The ASD26 series 2.5" SATA SSD primarily targets SATA based servers, fanless laptop PCs, highly rugged mobile
client devices, as well as thin and light mini/sub-notebooks. Key attributes include high performance, low
power, increased system responsiveness, high reliability, and enhanced ruggedness as compared to standard
mobile SATA hard drives. The ASD26 series 2.5" SATA SSD is available in a 2.5" form factor that is electrically,
mechanically, and software compatible with existing 2.5” Serial ATA slots and cables. Our flexible design allows
interchangeability with existing mobile hard drives based on the SATA interface standard.

1.2 Product Specification

1.2.1. Form Factor: 2.5” SSD form factor

1.2.2. Capacity: 32 GB (ASD26-MT1032-CT/ ASD26-MT1032-ET)

64 GB (ASD26-MT1064-CT/ ASD26-MT1064-ET)

128 GB (ASD26-MT1128-CT/ ASD26-MT1128-ET)

256 GB (ASD26-MT1256-CT/ ASD26-MT1256-ET )

512 GB (ASD26-MT1512-CT/ ASD26-MT1512-EP )

CT: Commercial Temperature 0 to +70°C, ET: Extend Temperature ‐40°C to +85°C

EP: Extend Temperature ‐40°C to +85°C with PLDP (Power loss data protection)

Unformatted capacity

32GB 62,533,296

64GB 125,045,424
128 GB 250,069,680
256 GB 500,118,192
512 GB 1,000,215,216

Table 1: User Addressable Sectors

Total user addressable sectors

in LBA mode

Notes: 1. 1GB=1,000,000,000 bytes and not all of the memory can be used for storage.

2. 1 Sector = 512 bytes

Specification 5

1.2.3. Flash: Multi-Level Cell (MLC) component with Toggle-Mode (19nm)

1.2.4. Band Performance

ASD26-MT1XXX-CT:

Capacity Access Type MB/s

32GB

64GB

128GB

256GB

512GB

ASD26-MT1 ET & ASD26-MT1 EP:

Capacity Access Type MB/s

32GB

64GB

Sequential Read Up to 440 (SATA 6 Gb/s)

Sequential Write Up to 83 (SATA 6 Gb/s)

Sequential Read Up to 410 (SATA 6 Gb/s)

Sequential Write Up to 160 (SATA 6 Gb/s)

Sequential Read Up to 530 (SATA 6 Gb/s)

Sequential Write Up to 310 (SATA 6 Gb/s)

Sequential Read Up to 530 (SATA 6 Gb/s)

Sequential Write Up to 440 (SATA 6 Gb/s)

Sequential Read Up to 530 (SATA 6 Gb/s)

Sequential Write Up to 450 (SATA 6 Gb/s)

(on normal mode)

Sequential Read Up to 440 (SATA 6 Gb/s)

Sequential Write Up to 83 (SATA 6 Gb/s)

Sequential Read Up to 410 (SATA 6 Gb/s)

Sequential Write Up to 160 (SATA 6 Gb/s)

128GB

Sequential Read Up to 520 (SATA 6 Gb/s)

Sequential Write Up to 290 (SATA 6 Gb/s)

Sequential Read Up to 500 (SATA 6 Gb/s)

256GB

Sequential Write Up to 430 (SATA 6 Gb/s)

Sequential Read Up to 510 (SATA 6 Gb/s)

512GB

Sequential Write Up to 430 (SATA 6 Gb/s)

Table 2: Maximum Sustained Read and Write Bandwidth

Notes: 1). Performance measured using CrystalDiskMark, ATTO.

2). 1 MB/sec = 1,048,576 bytes/sec is used in measuring sequential performance. If

1 MB/sec = 1,000,000 bytes/sec is used, performance values become 4.85% higher.

3). Test platform: Sandy Bridge (Windows 7 64-bit)

4). Actual performance dependent on specific application.

6 Specification

1.2.5. Read and Write IOPS

ASD26-MT1XXX-CT:

Capacity Access Type IOPS

32GB

64GB

128GB

256GB

512GB

4K Read (IOPS) 40,000 (SATA 6 Gb/s)

4K Write (IOPS) 20,000 (SATA 6 Gb/s)

4K Read (IOPS) 40,000 (SATA 6 Gb/s)

4K Write (IOPS) 40,000 (SATA 6 Gb/s)

4K Read (IOPS) 89,000 (SATA 6 Gb/s)

4K Write (IOPS) 75,000 (SATA 6 Gb/s)

4K Read (IOPS) 95,000 (SATA 6 Gb/s)

4K Write (IOPS) 80,000 (SATA 6 Gb/s)

4K Read (IOPS) 94,000 (SATA 6 Gb/s)

4K Write (IOPS) 81,000 (SATA 6 Gb/s)

ASD26-MT1XXX-ET: (on normal mode)

Capacity Access Type IOPS

32GB

64GB

128GB

256GB

512GB

Table 3: Random Read/Write Input/Output Operations per Second

Notes: 1. Performance measured using IOMETER Pro with queue depth set to 32

2. Write cache enabled

4K Read (IOPS) 40,000 (SATA 6 Gb/s)

4K Write (IOPS) 20,000 (SATA 6 Gb/s)

4K Read (IOPS) 50,000 (SATA 6 Gb/s)

4K Write (IOPS) 40,000 (SATA 6 Gb/s)

4K Read (IOPS) 70,000 (SATA 6 Gb/s)

4K Write (IOPS) 50,000 (SATA 6 Gb/s)

4K Read (IOPS) 70,000 (SATA 6 Gb/s)

4K Write (IOPS) 70,000 (SATA 6 Gb/s)

4K Read (IOPS) 70,000 (SATA 6 Gb/s)

4K Write (IOPS) 70,000 (SATA 6 Gb/s)

3. Test platform: Sandy Bridge (Windows 7, 64-bit)

Specification 7

1.2.6. Power On to Ready:

Notes: 1. Write cache enabled

2. Device measured using Drive Master

3. Power on to ready time assumes proper shutdown

(Power removal preceded by STANDBY command)

1.2.7. Compatibility

-- SATA Revision 3.0 compliant

Compatible with SATA 1.5 Gb/s, 3.0 Gb/s & 6.0 Gb/s interfaces

-- ATA/ATAPI- 8 compliant

Type Average Latency

Power on to Ready 1s

Table 4: Latency Specifications

-- SSD enhanced SMART ATA feature set

-- Native Command Queuing (NCQ) command set

-- TRIM supported

1.2.8. Certifications

1.2.9. Power Management

-- 5V SATA

-- SATA interface power management

-- OS-aware hot plug/removal

Certification Description

Indicates conformity with the essential health and safety

CE compliant

UL certified

(only for CT models)

BSMI

Microsoft WHQL Microsoft Windows Hardware Quality Labs

RoHS compliant Restriction of Hazardous Substance Directive

requirements set out in European Directives Low voltage Directive
and EMC Directive

Underwriters Laboratories, Inc. Component Recognition UL60950-1

Compliance to the Taiwan EMC standard “Limits and methods of
Radio Disturbance Characteristics of Information Technology
Equipment, CNS 13438 Class B”

Table 6: Device Certifications

8 Specification

1.2.10. Power Consumption

Capacity Description Min Max Unit

128GB Operating voltage for 5V (+/- 5%) 4.75 5.25 V

256GB Operating voltage for 5V (+/- 5%) 4.75 5.25 V

512GB Operating voltage for 5V (+/- 5%) 4.75 5.25 V

32GB Operating voltage for 5V (+/- 5%) 4.75 5.25 V

64GB Operating voltage for 5V (+/- 5%) 4.75 5.25 V

Table 7: Operating Voltage

Capacity Mode Type Unit

32GB

64GB

Active (average) 2.5 W

Idle (average) 0.5 W

Active (average) 2.5 W

Idle (average) 0.5 W

Note: Active power is measured using IOMETER Power Consumption using Data Logger _No

DIPM

1.2.11. Temperature

128GB

256GB

512GB

Environment Mode Min Max Units

Ambient

Temperature

Humidity

Active (average) 2.5 W

Idle (average) 0.5 W

Active (average) 2.5 W

Idle (average) 0.5 W

Active (average) 2.5 W

Idle (average) 0.5 W

Table 8: Typical Power Consumption

Operating (CT) 0 70 °C

Operating (ET) -40 85 °C

Non-operating -40 85 °C

Operating 5 95 %

Non-operating 5 95 %

Table 9: Temperature Relative Specifications

Note: Measured without condensation

1.2.12. Reliability

Specification 9

Mean Time between Failure (MTBF)

Power on/off cycles 50,000 cycles

Minimum useful life 3 years

1.2.13. Shock and Vibration:

Item Mode Timing/Frequency Max

Parameter Value

Table 10: Reliability specifications

Non-operating At 0.5 msec 1500G

> 1,500,000 hours

Shock1

Vibration2

Notes:

1. Shock specifications assume that the SSD is mounted securely with the input vibration

applied to the drive mounting screws. Stimulus may be applied in the X, Y or Z axis

2. Vibration specifications assume that the SSD is mounted securely with the input

vibration applied to the drive mounting screws. Stimulus may be applied in the X, Y or Z

axis. The measured specification is in root mean squared form.

Non-operating At 1 msec 1500G

Non-operating At 2 msec 1000G

Operating 7~800 Hz 2.17Grms

Non-operating 7~800 Hz 3.08Grms

Table11: Shock and Vibration

10 Specification

1.2.14. Electromagnetic Immunity:

Electromagnetic Immunity tests assume the SSD is properly installed in the representative host system. The
drive operates properly without errors degradation in performance when subjected to radio frequency (RF)
environments defined in the following table.

Test Description Performance criteria Reference standard

Electrostatic discharge

Radiated RF immunity

Electrical fast transient

Surge immunity

Conducted RF immunity

Voltage dips, interrupts

Notes:

1. Performance criterion A = The device shall continue to operate as intended, i.e.,

normal unit operation with no degradation of performance.

2. Performance criterion B = The device shall continue to operate as intended after

completion of test, however, during the test, some degradation of performance is
allowed as long as there is no data loss operator intervention to restore device
function.

3. Performance criterion C = Temporary loss of function is allowed. Operator

intervention is acceptable to restore device function.

4. Contact electrostatic discharge is applied to drive enclosure.

1.2.15. Weight: 80 g (with enclosure)

1.2.16. Dimension: 100.0mm x 69.8mm x 9.5 mm (L x W x H)

Contact, HCP, VCP: ±8KV

Air: ±15KV

80~1000MHz, 3V/m,

80% AM with 1 KHz sine

900 MHz, 3 V/m, 50%

pulse modulation at

200Hz

±1KV on AC mains
±0.5KV on external I/O
±1KV differential ±2KV

common, AC mains

150KHz~80 MHz, 3 Vrms,

80% AM with 1KHz sine

0% open, 5 sec
0% short, 5 sec

Table 12: Radio Frequency Specifications

40%, 0.10 sec
70%, 0.01 sec

B EN 61000-4-2:95

A

B EN 61000-4-4:95

B EN 61000-4-5:95

A EN 61000-4-6:97

C
C
C
B

EN 61000-4-3:96

ENV 50204:95

EN 61000-4-11:94

Specification 11

1.2.17. Part Numbers:

Product Name Part No.

ASD26-MT1032-CT 92-99059-7010

ASD26-MT11064-CT 92-99059-7110

ASD26-MT1128-CT 92-99059-7210

ASD26-MT1256-CT 92-99059-7310

ASD26-MT1512-CT 92-99059-7410
ASD26-MT1032-ET 92-99059-3310

ASD26-MT11064-ET 92-99059-3410

ASD26-MT1128-ET 92-99059-3510

ASD26-MT1256-ET 92-99059-3610

ASD26-MT1512-EP 92-99059-3710

1.3 Functional Block Diagram

DDR3

SDRAM

SATA

Host

Interface

Flash Memory

Controller

NAND

Flash
Array

Product Name DRAM Cache Size

ASD26-MT1032-CT 2Gb (256MB) DDR3 SDRAM

ASD26-MT1064-CT 2Gb (256MB) DDR3 SDRAM

ASD26-MT1128-CT 2Gb (256MB) DDR3 SDRAM

ASD26-MT1256-CT 4Gb (512MB) DDR3 SDRAM

ASD26-MT1512-CT 6Gb (768MB) DDR3 SDRAM

ASD26-MT1032-ET 2Gb (256MB) DDR3 SDRAM

ASD26-MT1064-ET 2Gb (256MB) DDR3 SDRAM

ASD26-MT1128-ET 2Gb (256MB) DDR3 SDRAM

ASD26-MT1256-ET 4Gb (512MB) DDR3 SDRAM

ASD26-MT1512-EP 6Gb (768MB) DDR3 SDRAM

12 Specification

1.4 Product Image

Specification 13

1.5 Mechanical Drawing:

Dimensions: 100.0 x 69.8mm x 9.5 mm (L x W x H)

14 Specification

1.6 Architecture

The ASD26 series 2.5" SATA Solid State Drive (SSD) utilizes a cost effective system-on-chip (SoC) design to

provide a full 6 Gb/s bandwidth with the host while managing multiple flash memory devices on multiple

channels internally.

1.7 Hot Plug Support

Hot Plug insertion and removal are supported when the correct connector and an appropriate operating

system (OS) are used as described in the SATA 3.0 Specification. This product supports asynchronous signal

recovery and will establish communications with a host system without hardware device detection by

issuing an unsolicited COMINIT when first mated with a powered connector.

Specification 15

2 Pin Locations and Signal Descriptions

2.1 Pin Locations

The data and power connector pin locations of the ASD26 series 2.5" SATA SSD are as shown below.

2.2 Signal Descriptions

Data Connector:

Name Type Description

S1
S2
S3
S4
S5
S6
S7

GND

A+

A-

GND

B-

B+

GND

Table 13: Serial ATA Data Connector Pin Definitions

Differential Signal Pair A

Differential Signal Pair B

16 Specification

Power Connector:

Name Type Description

P1 V33 3.3V Power
P2 V33 3.3V Power
P3 V33 3.3V Power, Pre-change
P4 GND
P5 GND
P6 GND
P7 V5 5V Power, Pre-change
P8 V5 5V Power
P9 V5 5V Power

P10 GND

P11 DAS/DSS

P12 GND
P13 V12 12V Power, Pre-change
P14 V12 12V Power
P15 V12 12V Power

Table 14: Serial ATA Power Connector Pin Definitions

Device Activity Signal /

Disable Staggered Spin up

Note:

1. All pins are in a single row, with a 1.27mm (0.05”) pitch

2. Pins P1, P2 and P3 are connected together, although they are not connected internally to

the device. The host may put 3.3v on these pins.

3. The mating sequence is

- The ground pins P4-P6, P10, P12 and the 5V power pin P7

- The signal pins and the rest of the 5V power pins P8-P9

4. Ground connectors P4 and P12 may contact before the other 1st mate pins in both the

power and signal connectors to discharge ESD in a suitably configured backplane connector.

5. Power pins P7, P8 and P9 are internally connected to one another within the device.

6. The host may ground P11 if it is not used for Device Activity Signal (DAS)

7. Pins P13, P14, P15 are connected together, although they are not connected internally to

the device.

Specification 17

3 ATA Command Sets

3.1 ATA Command

The ASD26 series 2.5" SATA SSD supports all the mandatory ATA commands defined in the ATA/ATAPI-8

specification.

3.1.1 ATA General Feature Command Set

The ASD26 series 2.5" SATA SSD supports the ATA General feature Command set (non-packet), which

consists of

．EXECUTE DEVICE DIAGNOSTIC

．FLUSH CACHE

．IDENTIFY DEVICE

．READ DMA

．READ SECTOR(S)

．READ VERIFY SECTORS(S)

．SEEK

．SET FEATURES

．WRITE DMA

．WRITE SECTOR(S)

．READ MULTIPLE

．SET MULTIPLE MODE

．WRITE MULTIPLE

The ASD26 series 2.5" SATA SSD supports all the following optional commands

．READ BUFFER

．WRITE BUFFER

．NOP

．DOWNLOAD MICROCODE

18 Specification

gical sectors per logical

Maximum number of sectors transferred

3.1.2 Identify Device Data

The following table details the sector data returned after issuing an IDENTIFY DEVICE command.

F=Fixed

Word

0 F 0040h

1 X 3FFFh Obsolete-Number of logical cylinders (16,383)

2 V C837h Specific configuration

3 X 0010h Obsolete-Number of logical heads (16)

4-5 X 0h Retired

6 X 003Fh

7-8 V 0h

9 X 0h Retired

V=Variable

X=Both

Default Value

General configuration bit-significant

Obsolete-Number of lo

Reserved for assignment by the Compact

Description

information

track (63)

Flash Association

10-19 F varies Serial number (20 ASCII characters)

20-21 X 0h Retired

22 X 0h Obsolete

23-26 F varies Firmware revision (8 ASCII characters)

27-46 F varies Model number

7:0 –

47 F 8010h

48 F 0h Reserved

49 F 2F00h Capabilities

50 F 4000h Capabilities

51-52 X 0h Obsolete

53 F 0007h Words 88 and 70:64 valid

54 X 3FFFh

55 X 0010h Obsolete - Number of logical heads (16)

56 X 003Fh

57-58 X 00FBFC10h Obsolete

59 F 0101h

60-62 125,045,424

63

F

(64GB)

per interrupt on multiple commands

Obsolete - Number of logical cylinders

(16,383)

Obsolete - Number of logical sectors per

logical track (63)

Number of sectors transferred per interrupt

on multiple commands

Total number of user addressable sectors

Specification 19

Minimum PIO transfer cycle time without flow

F=Fixed

Word

V=Variable

X=Both

Default Value

Description

64 F 0007h Multi-word DMA modes supported/selected

65 F 0003h PIO modes supported

66 F 0078h

67 F 0078h

68 F 0078h

69-70 F 0078h

71-74 F 0h

75 F 0h

76 F 001Eh Queue depth

77 F 0106h Serial ATA capabilities

78 F 0h Reserved for future Serial ATA definition

79 F 0048h Serial ATA features supported

80 V 0040h Serial ATA features enabled

81 F 00FCh Major Version Number

Minimum multiword DMA transfer cycle time

per word

Manufacture’s recommended multiword

DMA transfer cycle time

control

Minimum PIO transfer cycle time with IORDY

flow control

Reserved (for future command overlap and

queuing)

Reserved for the IDENTIFY packet DEVICE

command

82 F 001Ah Minor Version Number

83 F 746Bh Command set supported

84 F 7C01h Command sets supported

85 F 6123h Command set /feature supported extension

86 V 7469h Command set /feature enabled

87 V BC01h Command set /feature enabled

88 V 6123h Command set /feature default

89 V 407Fh Ultra DMA modes

90 F 0001h

91 F 0001h

92 V 0h Current advanced power management value

93 V 0FFFEh Master Password Revision Code

94 F 0h

Time required for security erase unit

completion

Time required for enhanced security erase

completion

Hardware reset result. The contents of bits

(12:0) of this word shall change only during

the execution of a hardware reset.

20 Specification

F=Fixed

Word

95 V 0h

96 F 0h Stream Minimum Request Size

97 V 0h Streaming Transfer Time - DMA

98-99 V 0h Streaming Access Latency - DMA and PIO

V=Variable

X=Both

Default Value

Vendor’s recommended and actual acoustic

Description

management value

100-103

108-111

112-115

117-118

121-126

129-159

104 125,045,424

105

106 V 0h Streaming Transfer Time - PIO

107 F 0h Reserved

116 F varies Unique ID

119 V 0h Reserved for technical report

120 F 0h Words per logical sector

127 F 401Ch Command set/feature enabled/Supported

128 F 0h Reserved

160 V 0021h Security status

F 0h Streaming Performance Granularity

V

(64GB)

F 4000h Physical sector size/logical sector size

F 0h

F 0h

F 401Ch Supported settings

F 0h

Maximum user LBA for 48-bit Address feature

set

Inter-seek delay for ISO-7779 acoustic testing

in microseconds

Reserved for word wide name extension to

128 bits

Removable Media Status Notification feature

set support

161-175

176-205

206-216

218-221

223-233

217 V 0h Current media serial number

222 F 0001h Non-rotating media device

234 F 101F Reserved

X 0h Vendor specific

F 0h

X 0h Reserved for assignment by the CFA

F 0h Reserved

F 0h Reserved

Compact Flash Association (CFA) power mode

1

Specification 21

F=Fixed

Word

235 F 0h Reserved

V=Variable

X=Both

Default Value

Description

236-254

236-254

Notes:

255 02A0h Reserved

255 X varies Integrity word (checksum and signature)

1. F=Fixed. The content of the word is fixed and does not change for removable media devices,

these values may change when media is Removed or changed.

2. V=Variable. The state of at least one bit in a word is variable and may change depending on

the state of the device or the commands executed by the device.

3. X=F or V. The content of the word may be fixed or variable.

0001h Reserved

F 0h Reserved

Table 15: Returned Sector Data

3.2 Power Management Command Set

The ASD26 series 2.5" SATA SSD supports the power management command set, which consists of

．CHECK POWER MODE

．IDLE

．IDLE IMMEDIATE

．SLEEP

．STANDBY

．STANDBY IMMEDIATE

22 Specification

3.3 Security Mode Feature Set

The ASD26 series 2.5" SATA SSD supports the Security Mode command set, which consist of

．SECURITY SET PASSWORD

．SECURITY UNLOCK

．SECURITY ERASE PREPARE

．SECURITY ERASE UNIT

．SECURITY FREEZE LOCK

．SECURITY DISABLE PASSWORD

3.4 SMART Command Set

The ASD26 series 2.5" SATA SSD supports the SMART command set, which consist of

．SMART ENABLE OPERATIONS

．SMART DISABLE OPERATIONS

．SMART ENABLE/DISABLE AUTOSAVE

．SMART RETURN STATUS

The ASD26 series 2.5" SATA SSD supports the the following optional commands.

．SMART EXECUTE OFF-LINE IMMEDIATE

．SMART READ DATA

．SMART READ LOG

．SMART WRITE LOG

The table below lists the SMART commands.

Specification 23

Subcommand Code LBA Low value

SMART ATTRIBUTE VALUES (READ DATA) D0h

READ ATTRIBUTE THRESHOLDS D1h

ENABLE/DISABLE ATTRIBUTE AUTOSAVE D2h

SAVE ATTRIBUTE VALUES D3h

EXECUTE OFF-LINE IMMEDIATE D4h

EXECUTE SMART OFF-LINE ROUTINE

EXECUTE SMART SHORT SELF-TEST ROUTINE (OFFLINE)

EXECUTE SMART EXTENDED SELF-TEST ROUTINE (OFFLINE)

ABORT OFF-LINE ROUTINE

EXECUTE SMART SHORT SELF-TEST ROUTINE (CAPTIVE)

EXECUTE SMART EXTENDED SELF-TEST ROUTINE (CAPTIVE)

READ LOG SECTOR D5h

WRITE LOG SECTOR D6h

ENABLE SMART OPERATIONS D8h

DISABLE SMART OPERATIONS D9h

RETURN SMART STATUS DAh

00h

01h

02h

7Fh

81h

82h

Table 16: SMART commands

3.5 Host Protected Area Command Set

The ASD26 series 2.5" SATA SSD supports the Host Protected Area command set which consists of

．READ NATIVE MAX ADDRESS

．SET MAX ADDRESS

．READ NATIVE MAX ADDRESS EXT

．SET MAX ADDRESS EXT

The ASD26 series 2.5" SATA SSD supports the following optional commands.

．SET MAX SET PASSWORD

．SET MAX LOCK

．SET MAX FREEZE LOCK

．SET MAX UNLOCK

3.6 48-Bit Address Command Set

The ASD26 series 2.5" SATA SSD supports the Host Protected Area command set, which consists of

24 Specification

．READ NATIVE MAX ADDRESS

．FLUSH CACHE EXT

．READ DMA EXT

．READ NATIVE MAX ADDRESS EXT

．READ SECTOR(S) EXT

．READ VERIFY SECTOR(S) EXT

．SET MAX ADDRESS EXT

．WRITE DMA EXT

．WRITE MULTIPLE EXT

．WRITE SECTOR(S) EXT

3.7 Device Configuration Overlay Command Set

The ASD26 series 2.5" SATA SSD supports the Device configuration Overlay command set, which consists of

．DEVICE CONFIGURATION FREEZE LOCK

．DEVICE CONFIGURATION IDENTITY

．DEVICE CONFIGURATION RESTORE

．DEVICE CONFIGURATION SET

3.8 General Purpose log Command Set

The ASD26 series 2.5" SATA SSD supports the general purpose log command set, which consists of

．READ LOG EXT

．WRITE LOG EXT

Specification 25

4 SATA Command Sets

4.1 SATA Command

The SATA 3.0 Specification is a super set of the ATA/ATAPI-8 specification with regard to supported

commands. The ASD26-MT1 series 2.5" SATA 6.0 Gb/s SSD supports the following features which are

unique to the SATA 3.0 Specification.

4.1.1. Software Settings Preservation

The ASD26 series 2.5" SATA SSD supports the SET FEATURES parameter to enable/disable the

preservation of software settings.

4.1.2. Native Command Queuing

The ASD26 series 2.5" SATA SSD supports the Native Command Queuing (NCQ) command set, which

includes.

．READ FPDMA QUEUED

．WRITE FPDMA QUEUED

Note: with a maximum queue depth equal to 31

26 Specification

5 References

This document references standards defined by a variety of organizations as listed below.

Date Title Location

Dec 2008 VCCI

July 2007 ROHS

July 2007 SFF-8144, 1.8” drive form factor http://www.sffcommittee.org

February 2007

Serial ATA Revision 2.6 http://www.sata-io.org

http://www.vcci.or.jp/vcci_e/general/jo

Search for material description

datasheet at http://intel.pcnalert.com

in/index.html

May 2006

May 2005 SFF-8201, 2.5” drive form factor http://www.sffcommittee.org

April 2004 ATA-7 Spec. Volume 1 http://www.t13.org/

Aug. 2009 ATA-8 Spec. Rev 2 http://www.t13.org/

1995

1996

1995

1995

1997

1994

1995

SFF-8223, 2.5” Drive w/Serial Attachment

Connector

International Electro Technical Commission

EB61000

4-2 Personnel Electrostatic Discharge Immunity

4-3 Electromagnetic compatibility (EMC)

4-4 Electromagnetic compatibility (EMC)

4-5 Electromagnetic compatibility (EMC)

4-6Electromagnetic compatibility (EMC)

4-11 (Voltage variations)

ENV 50204 (Radiated electromagnetic field

from digital radio telephones)

Table 17: Standards References

http://www.sffcommittee.org

http://www.iec.ch

http://www.iec.ch

Specification 27

6 Getting Service

Contact us should you require any service or assistance.

ADLINK Technology, Inc.

Address: 9F, No.166 Jian Yi Road, Zhonghe District
New Taipei City 235, Taiwan
新北市中和區建一路 166 號 9 樓
Tel: [phone]
Fax: [phone]
Email: [e-mail]

Ampro ADLINK Technology, Inc.

Address: 5215 Hellyer Avenue, #110, San Jose, CA 95138, USA
Tel: [phone]
Toll Free: [phone] (USA only)
Fax: [phone]
Email: [e-mail]

ADLINK Technology (China) Co., Ltd.

Address: 上海市浦东新区张江高科技园区芳春路 300 号 (201203)
300 Fang Chun Rd., Zhangjiang Hi-Tech Park,
Pudong New Area, Shanghai, 201203 China
Tel: [phone]
Fax: [phone]
Email: [e-mail]

ADLINK Technology Beijing

Address: 北京市海淀区上地东路 1 号盈创动力大厦 E 座 801 室(100085)

Rm. 801, Power Creative E, No. 1, B/D

Shang Di East Rd., Beijing, 100085 China
Tel: [phone]
Fax: [phone]
Email: [e-mail]

ADLINK Technology Shenzhen

Address: 深圳市南山区科技园南区高新南七道 数字技术园 A1 栋 2 楼 C 区 (518057)

2F, C Block, Bldg. A1, Cyber-Tech Zone, Gao Xin Ave. Sec. 7,

High-Tech Industrial Park S., Shenzhen, 518054 China
Tel: [phone]
Fax: [phone]
Email: [e-mail]

28 Specification

LiPPERT ADLINK Technology GmbH

Address: Hans-Thoma-Strasse 11, D-68163, Mannheim, Germany
Tel: [phone]
Fax: [phone]
Email: [e-mail]

ADLINK Technology, Inc. (French Liaison Office)

Address: 15 rue Emile Baudot, 91300 Massy CEDEX, France
Tel: [phone]
Fax: [phone]
Email: [e-mail]

ADLINK Technology Japan Corporation

Address: 〒101-0045 東京都千代田区神田鍛冶町 3-7-4

神田 374 ビル 4F

KANDA374 Bldg. 4F, 3-7-4 Kanda Kajicho,

Chiyoda-ku, Tokyo 101-0045, Japan
Tel: [phone]
Fax: [phone]
Email: [e-mail]

ADLINK Technology, Inc. (Korean Liaison Office)

Address: 8F Mointer B/D,1675-12, Seocho-Dong, Seocho-Gu, Seoul 137-070, Korea
8F Mointer B/D,1675-12, Seocho-Dong, Seocho-Gu,
Seoul 137-070, Korea
Tel: [phone]
Fax: [phone]
Email: [e-mail]

ADLINK Technology Singapore Pte. Ltd.

Address: 84 Genting Lane #07-02A, Cityneon Design Centre,

Singapore 349584
Tel: [phone]
Fax: [phone]
Email: [e-mail]

ADLINK Technology Singapore Pte. Ltd. (Indian Liaison Office)

Address: 1st Floor, #50-56 (Between 16th/17th Cross) Margosa Plaza,

Margosa Main Road, Malleswaram, Bangalore-560055, India
Tel: [phone]
Fax: [phone]
Email: [e-mail]

Specification 29